Search Documents

By AIME AIME

IN A STATEMENT summarizing general conditions in the Federated American Engineering Societies, the executive secretary, L. W. Wallace, expresses the belief that the Federation has made substantial progress. At the annual meeting of the American Engineering Council, to be held in Washington Jan. 5 and 6, this progress will be shown by reports covering activities in many fields. "Unquestionably," says Mr. Wallace, "the Federa¬tion has made favorable and permanent contacts in Washington. Through the, activities of Congress and of the new Federal administration. we have had the opportunity to render some really constructive service. We feel, however, that the great body of engineers are not adequately informed of the organization of the Federation, of its aims and purposes and of its activities.

Jan 1, 1921

By C. S. Giggins, F. S. Pettit

The oxidation of Ni-Cr alloys in 0.1 atm of oxygen has been studied at temperatures between 800" and 1200°C. For alloys with 30 wt pct or more Cr, continuous layers of Cr2O3 are formed during oxidation. In the case of alloys with chromium concentrations between approximately 5 to 30 wt pct, external scales of Cr203 are formed over grain boundaries whereas internal precipitates of Cr2O3 and external layers of NiO are formed at other areas on the alloy surface. When such conditions are present on the alloy surface, chromium diffuses laterally from those areas covered with a continuous layer of Cr2O3 to areas where a Cr2O3 sub scale exists and it is possible for the sub-scale zone to become separated from the alloy by a continuous layer of Cr2O3. Whether such a state will be attained depends upon the initial grain size of the alloy and the oxidation time. When the concentration of chromium in the alloy is less than 5 pct, Cr2O3 is formed internally both at grain boundaries and within the interior of grains and the alloy is covered with an external layer of NiO. MECHANISMS which describe the growth of oxide scales on nickel-base superalloys are complex and the effects produced by the various elements in these alloys on the oxidation behavior of superalloys are not clearly understood. In order to determine the influence of the different elements on the oxidation behavior of superalloys, it is first necessary to examine the oxidation properties of binary nickel-base systems which contain the principal elements present in the superalloys and then progressively more complex systems until compositions typical of the superalloys are attained. Chromium is present in virtually all nickel-base superalloys and the purpose of the present studies was to examine the selective oxidation of chromium in Ni-Cr alloys. The oxidation characteristics of Ni-Cr alloys have been extensively studied1-" to date principally as a result of the high oxidation resistance exhibited by some of these alloys. Ni-20Cr* has long been known *All compositions are given as wcight percent unless specified otherwise. to be oxidation resistant and is commonly used as resistance heating elements for service temperatures up to 1100°C. This alloy cannot be used for extended periods of time at higher temperatures because of the apparent reaction of the external scale with oxygen to form gaseous CrO3. In spite of the considerable work cited above some important aspects of Ni-Cr oxidation still remain unresolved. Virtually all of the previous studies agree that small additions of chromium to nickel, e.g., <10 wt pct Cr, result in increased oxidation rates as compared to that of pure nickel, whereas larger additions, e.g., 20 to 30 wt pct Cr, form alloys with substantially lower oxidation rates. The controversial aspects of the oxidation mechanisms for these alloys that still remain unresolved are as follows: 1) A description of the oxidation mechanism for the low chromium alloys. 2) A description of the oxidation mechanism for the high chromium alloys, particularly with respect to the composition of the external scale which results in the lower oxidation rates. 3) The specific alloy compositions at which the oxidation mechanism changes from that obtained for low chromium contents to that of the high chromium alloys and the reason for this transition. EXPERIMENTAL The Ni-Cr alloys listed in Table I were prepared from high purity metals by nonconsumably arc melting and casting as buttons. These alloys were then given a preliminary annealing treatment in argon at 815°C for 100 hr to promote homogeneity. Each button was cut into 0.250 in. thick sections that were subsequently cold-rolled to 0.050 in. thicknesses and annealed in argon at 815°C for 48 hr to provide a twinned, equi-axed grain structure. The grain size for these alloys was not uniform and the limits, within which the average grain size lies, are given in Table I for the single-phase alloys. All the alloys were single phase with the exception of the Ni4OCr alloy in agreement with the Ni-Cr phase diagram.&apos;&apos; Rectangular specimens were cut from the sheet to provide surface areas of approximately 2.5 sq cm. Exact areas were determined with a micrometer after surface preparation was completed. All of the specimens except the Ni-40Cr alloy and pure chromium were polished through 600-grit Sic abrasive paper, ultrasonically agitated in ethylene trichloride, rinsed with ethyl alcohol, and electro-polished. The specimens were electropolished in a 10 vol pct H2SO4 (conc), 6 vol pct lactic acid, methyl alcohol solution at 70" to 80°C for 2 min at a current density of 0.8 to 1.2 amp per sq cm. This electro-polishing procedure did not produce acceptable surfaces on the Ni-40Cr alloy nor on pure chromium and the oxidation properties of these materials were obtained for specimens polished through 600-grit Sic

Jan 1, 1970

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962

By Harold M. Feder, Robert V. Schablaske, Irving Johnson, Ewald Veleckis

The stoichiometry, structure, and stability of the internzediate phases formed between zinc and some of the rare earth (RE) metals were systematically exarnined by means of a recording effusion balance and X-ray diffraction analyses. In the La-, Ce-, PY-, Nd-, and Y-Zu systems, at or below about 600 C, the following sequences of phases (REZnx) were found: La, x = 1, 2, 4.0, 5.25, 7.3, 17/2, 11, and 13.0;&apos; Ce, x = 1, 2, 3, 11/3, 4.3, 5.25, 7.0, 17/2,* and 11; Pr,x = 1,2, 3, 11/3 ,* 4.3, 5.3(?), 7.0, 17/2,* and 11; Nd,x = 1,2, 3,* 11/3,* 4.3, 6.5, 8.5,* and 11; Y,x = 1,2,3, 11/3, 4.5, 5.0, 17/2,* and 12.* The structure types of all these phases were classified. In addition, lattice parameters were obtained for the first time for the pluses denoted by asterisks. In the absence of de tectable valency or electronegativity effects the systesnatic trends in the results have been ascribed to the effects of&apos; the lanthanide contraction. For example, the maximum number of zinc atoms in the coordination polyhedron surrounding the RE atom decreases from twenty-four to twenty-two to twenty as the size of the RE atom decreases. THE structures and compositions of a great many intermetallic phases (e.g., the Laves phases) are known to be based primarily, but not exclusively, on the space-filling efficiency of various modes of packing together atoms of different sizes. The valencies and electronegativities of the constituent atoms are, however, also influential. In extreme cases hypothetical intermetallic phases which fulfill the efficient spacefilling requirements may not be present in the constitutional diagram because of thermodynamic instability brought about by the operation of valency or electronegativity factors. Hence, for a detailed study of the influence of atomic size on alloy structure and composition, it would be desirable to minimize variations of valency and electronegativity. The intermetallic phases formed by the rave earths (RE) with some common partner offer an excellent opportunity for isolating the effects of size from those of valency and electronegativity. The rare earths exhibit a large, but smooth, decrease in size (the lanthanide contraction) in the series from lanthanum to lutetium when inter comparison is made for a common valence state, e.g., isolated atoms or trivalent ions. The elements yttrium and scandium are frequently included as pseudo rare earths; their sizes place them in the vicinity of dysprosium and lutetium, respectively. The electronegativities of RE elements vary by less than 10 pet. The trivalent state is the most common; however, the well-known tendency of cerium, praseodymium, and terbium to achieve higher valencies, and of samarium, europium, and ytterbium to seek lower valencies, requires that caution be exercised in the assumption of equal valencies. In the present study the existence, constitution, and structure of each of the numerous intermediate phases formed by zinc with lanthanum, cerium, praseodymium, neodymium, or yttrium were examined systematically and in detail. The investigation was conducted by a recording effusion balance technique and by X-ray diffraction analysis. The results enrich our knowledge of the phase diagrams of these systems. In addition, they present some clear-cut evidences of the operation of the size factor alone. EXPERIMENTAL PROCEDURE Apparatus. The mode of operation of the recording effusion balance and its application to phase studies have been discussed in detail elsewhere.&apos; In this work, an effusion cell containing a finely divided alloy was suspended within an evacuated tube from the beam of an analytical balance. The tube was immersed in a massive molten salt bath whose temperature was controlled to within 0.5o C during each experiment. The loss in weight of the alloy owing to effusion of zinc* was continuously recorded. Two effusion cells, 1/2 in. diam by 1 in. high, were machined from tantalum rods. Two orifices were drilled laterally into the walls of each cell. The orifice areas were determined by calibration with pure zinc: cell A had a total orifice area of 6.5 x 10-41 sq cm, and cell B an orifice area of 9.8 x 10-3 sq cm. By appropriate choices of orifice area and temperature the wide range of volatilities from pure zinc to pure rare earth metal could be investigated. X-ray diffraction powder photographs were made at room temperature with a 114.6-mm Debye-Scherrer camera with both filtered CuKa radiation and filtered CrKa radiation. Lattice parameters were refined by a computer-programmed least-squares analytical treatment which incorporated appropriate extrapolation techniques.2 Frequent use was also made of a special computer program3 designed to generate a powder pattern from an assumed structure in order to verify structural assignments. Materials. Lanthanum, neodymium, and yttrium were purchased from the Lunex Co., cerium from the Cerium Metals Corp., and praseodymium from the St.

Jan 1, 1968

By O. Hoover, M. Herman, V. V. Damiano

The Jetter and borie&apos; teclznique of determining textures using a spherical specimen has been applied to tlze study of compression-rolled beryllium sheet. Snzall spheres the order of 1 mm in diam cut from the beryllium sheet were autotnatically rotated about tz41o axes using the G.E. single-crystal goniometer. Quantitative pole figures were obtained without tke need to apply absorption corrections. Compression-rolled beryllium exhibited peak intensities ,for (0002) planes of positions tilted 10 deg to the rolling plane and a near random distribution of (1010) planes about the nornal to the rolling plane. TECHNIQUES for determining textures of rolled sheet material are amply described in the literature. The techniques are found to be variations of two basic methods. One due to Decker, Asp, and arker, referred to as the transmission method, utilizes a thin-sheet specimen in which the X-ray beam enters the specimen from one side and the intensity of the beam which emerges from the opposite side is measured. The second method due to chulz,3 referred to as the reflection method, utilizes a thick specimen and the intensity of the beam emerging from the same side is measured. The two rotations of the specimen in the beam are designated a and 8. In order to completely determine the texture of sheet material, it is generally necessary to use a combination of the two methods. The calculations involved in correcting the raw X-ray data for absorption effects and the combining of the data obtained by the two methods are very laborious and time consuming. To avoid the intensity corrections which arise as a result of the changing diffraction volume and path length within the sample other methods have been proposed. The Norton method utilizes a cylindrically shaped specimen cut from the sheet material. Since the rods have rotational symmetry, the absorption correction is constant for rotations about the sheet texture. Jetter and Borie&apos; employed a spherical specimen to analyze the fiber texture of extruded aluminum rods. The spheres were rotated rapidly about the fiber axis to include a large number of grains in the X-ray beam and changes in intensity with respect to tilts of the fiber axis were measured. The absorption correction was constant for all angles and was neglected. The Jetter and Borie&apos; technique finds excellent ap- plication to very fine-grained low-absorbing metals in which the entire sphere volume can contribute to the diffraction volume. In the case of low-absorbing metals, however, serious limitations on specimen thickness occur as demonstrated by Braggs due to de-focussing effects. Peak shifts may occur which negate the assumption that integrated intensities are proportional to peak intensities. These limitations in sphere size to the order of 0.5 to 1 mm for beryllium require that the grain size be sufficiently small to include a large enough statistical sample. The present paper describes the application of spherical specimens less than 1 mm in diam to the quantitative determination of pole figures for compression-rolled beryllium sheet having a grain size the order of 10 p. EXPERIMENTAL 1) Specimen Preparation. Two techniques for spark-machining beryllium spheres were tried. One involved the use of a hollow cylinder as a cutting tool. The tool was fed into the rotating cylindrical specimen as shown in Fig. l(a). The hollow cylinder was carefully aligned such that the axis of the cylinder and the axis of the specimen lay in the same plane and were 90 deg to each other. As the hollow cylinder was fed into the rotating cylindrical specimen, a spherical shape was formed as shown in Fig. 1. Alignment was very critical. Slight misalignment resulted in the formation of a barrel-shaped specimen instead of a sphere. A second technique involved the use of a cutting wheel shaped as shown in Fig. 2 with a groove of the desired radius. A section of the sheet specimen was first turned into a cylinder on the left part of the cutting wheel. It was then shifted to the right and a spherical specimen was turned as shown in Fig. 2. The axis of the cylinder lay in the plane of the sheet. Flats corresponding to the rolling plane of the sheet were used to grip the specimen during the machining operation and these served to identify the rolling plane of the sphere. 2) Rotation of Spec=. The spherical specimen is shown mounted on the G.E. single-crystal goniometer in Fig. 3. The knob A of the goniometer shown in Fig. 3 rotates the specimen about the pedestal axis. These angles have been designated as @ angles. The knob B rotates the specimen about an axis perpendicular to the pedestal axis. These angles have been designated as p angles. A device was made to automatically drive the single-crystal goniometer by means of two flexible shafts connected to the A and B knobs as shown in Fig. 3. The motor system was designed to rotate the knob A, thus rotating the specimen through angles of $I while the B knob remained stationary. After one complete

Jan 1, 1967

By M. J. Pool

The partial molar heats of solution in liquid tin of cadmium, silver, tellurium, and zinc have been measured at 655°. 700°, and 750°K by liquid-metal solution calorimetry. Silver, cadmium, and zinc are endothermic at these temperatures while tellurium is exothermic. Only the heat of solution of silver depends on composition while all four elements show a temperature-de pendent heat of solution. The heat of solution of tellurium is constant up to 0.6 g-at. pct, becomes increasingly more exothermic, and reaches a limiting value at 1 g-at. pct Te. The limiting value has been used to calculate the heat of formation of SnTe at 750°K. The heat effects associated with the dissolution of the compounds Ag2 Te, CdTe, and ZnTe in liquid tin were measured at 750°K. These values are cotnOined with the measured hat effects at 750°Kfor silver, cadmium, tellurium, and zinc to detertrline the heats of formation of the telluride compounds. Cadmium lelluride exhibits a heat of dissolution which has a compositional dependence. THERE is a considerable amount of interest in the compounds of tellurium because of their electronic properties. Both cadmium and zinc tellurides are thermoelectric materials and considerable work has been done on their electronic properties but a limited amount of data is available on their ther-modynamic properties. This work was undertaken to elucidate the heat of formation data on cadmium and zinc telluride. Since both cadmium and zinc are in Group II it seemed to be of interest to compare the values obtained for them with the heat of formation of a Group I telluride. Silver telluride was selected for this comparison. In the course of the work it was also possible to determine the heat of formation of tin telluride and therefore to make a comparison of some of the Group I, 11, and lV tellurides with the metallic elements silver, cadmium, and tin being in the same period. There is also a great deal of interest in the energetic changes which occur upon addition of solute elements to a common solvent. This investigation provided an opportunity to study the partial molar heats of solution of silver, cadmium, tellurium, and zinc in liquid tin. The partial molar heats of solution are of theoretical interest because solute-solute interactions are a minimum in dilute solutions and application of solution models is simpli- fied. In order to complete the analysis of solute-solute and solute-solvent interactions the temperature dependence of the partial molar heats of solution was also measured. MATERIALS AND EXPERIMENTAL PROCEDURE All materials were of the highest purity available. The silver, zinc, cadmium, and tellurium were obtained from American Smelting and Refining Co. and were reported to be 99.999 pct pure. The silver telluride, zinc telluride, and cadmium telluride were obtained from Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp., and were electronic-grade material of 99.999 pct purity. Tin used for the solvent bath and for calibration was obtained from the Vulcan Manufacturing Co. and was reported as being 99.99 pct pure. The liquid-tin solution calorimeter used in this work is similar in principle to the differential twin-type calorimeter described by K1eppa.l Two of three identical calorimeter wells are used together during any set of experiments, one well being active and the other being passive. The wells are positioned 120 deg apart in an aluminum calorimeter block. Each well contains a multijunction thermopile and a Pyrex test tube to hold the liquid metal bath. Forty-eight of the thermopile junctions are distributed over the surface of each calorimeter well adjacent to the test tube and serve to integrate the heat effects occurring. The other forty-eight are next to the aluminum calorimeter block. The thermopiles for the three wells are connected differentially so that any change in temperature at the outer junctions (which will be the same for both wells because of the high conductivity of the aluminum block) will oppose for the two wells and result in no shift of the zero. The electrical output represents the true temperature difference between the two reaction vessels. A reaction occurring in the active well gives a comparison with another body of very similar thermal properties. In this way, any spurious heat effects due to slight temperature drifts within the entire calorimeter block are eliminated. The output of the differential thermopile goes to a dc amplifier with multiple ranges of from * 10 pv to 1 30 mv. The output of the amplifier is then fed into a Leeds and Northrup strip-chart recorder. The adiabatic temperature change is then calculated using the technique of Howlett, Leach, Ticknor, and ever.&apos; The aluminum calorimeter block is contained in a cylindrical furnace with main and control heaters

Jan 1, 1965

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena&apos; and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By F. G. Jones, R. D. Pehlke, H. E. Gardner

The solubility of nitrogen in liquid Fe-18 pct Cr-8 pct Ni-0. 7 to 2.3 pct A1 alloys has been measured up to the solubility limit for the formation of aluminum nitride in the temperature range 1600° to 1700°C uszng the Sieverts&apos; method. The solubility of nitrogen in 18-8 stainless steel increases with increasing aluminum content. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from the elements dissolved in liquid 18-8 stainless-steel alloys has been determined to be: ?G° = -42,500 + 20. IT in the range from 1600° to 1700° C. EVANS and pehlke1 have measured the equilibrium conditions for the formation of aluminum nitride, AlN, in liquid Fe-A1 alloys. The present study extends that work to the more complex solvent, liquid 18 pct Cr-8 pct Ni (18-8) stainless steel. Recent work by Small and pehlke2 has dealt with the effect of fourth-element additions on the solubility of nitrogen in 18-8 base alloys. They found the effect of aluminum additions, up to 0.74 pct, on the solubility of nitrogen to be small. The present study covered the range from 0.74 to 2.28 pct aluminum, and by extending the composition range may be used to better define the effect of aluminum on the nitrogen solubility in these alloys. EXPERIMENTAL PROCEDURE The Sieverts&apos; method was used to measure the equilibrium solubility of nitrogen gas in liquid 18-8 stainless steel alloys containing 0.74, 1.49, 1.93, and 2.28 pct Al. The solubility was measured as a function of the nitrogen gas pressure at temperatures of 1600°, 1650°, and 1700°C. The apparatus used is the same as described by Small and Pehlke.2 The 100-g melts were made from Ferrovac-E high-purity iron, Crucible Steel Co.; 99.95 pct Cr, Union Carbide Corp.; 99.9 pct Ni, International Nickel Co.; and 99.99+ pct Al, Aluminum Co. of America. The aluminum was charged at the bottom of the crucible, surrounded by nickel and iron. The chromium was packed into the interstices to minimize vapor transport of the aluminum during initial melting. The hot volume of the system, measured for each melt with argon, ranged from 45 to 55 standard cu cm with a temperature coefficient of —8 x 10-3 cu cm per °C. The melt temperature was measured with a Leeds and Northrup disappearing-filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature calibration of the system by Small and pehlke2 was assumed. Two problems are involved in determining the solubility product of a solid, metal nitride phase in liquid iron alloys. These are: 1) establishing the point of departure from Henrian behavior at the solubility limit of the metal nitride phase; and 2) determining the composition of the solid nitride which is precipitated. Determination of the solubility product of AlN was made by admitting small amounts of nitrogen into the reaction bulb until the deviation from Sieverts&apos; law was clearly evident in the form of a pressure halt. To obtain the solubility product at several temperatures during one run the following procedure was used: 1) add increments of nitrogen to determine the Sieverts&apos; law line at the lowest desired temperature; 2) continue to add nitrogen to precipitate a small amount of the nitride phase; 3) increase the melt temperature 50°C to dissolve the precipitated nitride; 4) repeat step 2 until either a nitride formed or the system reached ambient pressure; if a nitride formed at 1650°C, the sequence was repeated at 1700°C. The composition of the precipitated phase was checked by an X-ray diffraction pattern obtained from powder scraped from the surface of the solidified 1.93 pct A1 melt. RESULTS AND DISCUSSlON Solubility Measurements. Fig. 1 is a typical nitrogen-absorption curve obtained from measurements on a 1.93 pct A1 alloy. Since the initial absorption of nitrogen follows Sieverts&apos; law the nitrogen solubility is plotted as a function of the square root of the pressure of nitrogen gas in the reaction bulb. The results of the solubility measurements for all alloys studied are summarized in Table I. The slope of the Sieverts&apos; law line for each alloy was determined. Since this is also the solubility of nitrogen at 1 atm pressure of nitrogen gas, the latter designation is used for the data. It should be noted. however, that in most cases the value lies above the solubility limit for AlN. Fig. 2 shows the effect of aluminum on the solubility of nitrogen at this reference pressure and as a function of melt temperature. The solid portions of the lines represent attainable solutions; the dashed regions lie above the limit for precipitation of AlN.

Jan 1, 1969

By J. J. Gilman, T. A. Read

FOLLOWING the deformation 01 zinc monocrys-tals, sharply bent basal planes are observed near several types of inhomogeneities. Three of these in-homogeneities have characteristics which are quite regular so that they can be studied and analyzed. These are compressive kink bands, "deformation bands," and the inhomogeneities near end restraints. The present paper describes experiments in which "deformation bands" were artificially produced, and bend plane phenomena are discussed in terms of dislocation theory. Also, two new bend plane phenomena are described. The importance of bend plane phenomena in the deformation of crystals is not widely recognized. Many phenomena may be explained in a manner similar to the discussion in this paper. Jillson1 has pointed out that the "punching effect" in zinc is a bend plane phenomenon and is not caused by prismatic slip.&apos; Bowles3 has suggested that they may be involved in diffusionless phase changes. Cahn4 has discussed the role of bend plane formation in the polygonization of zinc. Experimental Work Tensile Kink Bands: Because of the geometrical similarity between "deformation bands" and "kink bands" (compare Fig. 1 of this paper with Fig. 1 of the paper by Hess and Barrett"), the band shown in Fig. 1 of this paper will be called a "tensile kink band," and that shown by Hess and Barrett will be called a "compressive kink band." It is felt that the term "deformation band" should be reserved for banded structures in polycrystalline materials such as iron." Tensile kink bands seem to form spontaneously in aluminum crystals deformed by tensile loading.7-10 In zinc and cadmium crystals they do not form in good, carefully loaded specimens.&apos;." However, tensile kink bands can be produced artificially in zinc crystals. The present authors did this by scratching one of the flat surfaces of triangular crystals transversely with a sharp needle. Natural tensile kink bands caused by inhomogeneities sometimes appeared in deformed crystals which were identical in appearance with the artificially produced ones. Zinc monocrystals were grown by the Bridgman method in graphite molds. Chemically pure zinc (99.999+ pct Zn) was used and the molds were sealed inside evacuated pyrex tubes during growth. The crystal cross sections were equilateral triangles with a typical base of 0.210 in. The artificial kink band shown in Fig. 1 is typical of tensile kink bands in zinc. The band lies between two bend planes which run from upper right to lower left and is inclined oppositely to the slip bands which are sharply bent at the two bend planes. The general form of the artificial tensile kink bands was independent of the scratch depth (1 to 5 mils deep) and also independent of which side was scratched. These variables did cause variations, however. Deep scratches produced more localized kink bands than light scratches. Also, if the angle between the slip plane traces and a transverse scratch varied appreciably among the three sides, then localization of the resulting kink bands also varied. Furthermore, if the slip direction lay nearly parallel to the scratched side, the band was more developed near the scratched side than at the opposite edge. Scratches produced tensile kink bands for crystal orientations from xo = 15" to x, = 75". Fig. 2 shows a scratched crystal after deformation. One triangular side lies in the plane of the photograph. The right hand tensile kink band was produced by a transverse scratch on the upper right side. The next two kink bands were the result of scratches on the front surface. The kink band at the left was caused by a scratch on the lower back side. All four bands have the same general form. A longitudinal scratch was also made on the crystal shown in Fig. 2 to determine the effect of a scratch on the critical shear stress. The critical shear stress of the scratched region was 33.9 g per sq mm compared to 24.4 g per sq mm for the un-scratched region above it. Fig. 3 shows Laue patterns of the crystal shown in Fig. 2. Fig. 3a shows the pattern of the undeformed crystal. The orientation was x, = 21°, A, = 31". After deformation, Fig. 3b was made of the homogeneously deformed portion of the crystal. The spots are compact but split into two halves. This region was elongated 45 pct and its orientation was x = 14", X = 20"; the sine law predicts x = 14", A = 20.5". Fig. 3c was taken near the center of the middle tensile kink band of Fig. 2. The pattern shows a range of orientations and polygonization in this region. The spread in orientation was due to the fact that the basal planes were curved (see Fig. 1) rather than flat as in the ideal case. Some may also have been the result of elastic distortions and "local curvatures." The orientation range was x = 23" to 32", A = 30" to 42". It is apparent from Fig. 3 that the material inside and outside the kink band rotated in opposite directions with respect to the tension axis during deformation. The orientation calculated from the ideal configuration of Fig. 9,

Jan 1, 1954

By C. A. Winkler, V. Hospadaruk

PREVIOUS papers from this laboratory have discussed the effect of chloride ion on the cathode polarization during electrodeposition of copper from copper sulphate-sulphuric acid electrolytes, in the presence and absence of gelatin. The steady state polarization&apos;" was found to decrease sharply and pass through a minimum with increasing chloride ion concentration in the presence of gelatin. The minimum shifted to higher chloride ion concentrations and to higher polarization values with increase in current density or gelatin concentration, while an increase of temperature shifted the minimum toward lower halide concentrations and lower polarizations. Since these observations were made in acid-copper sulphate electrolytes that contained no other addend than gelatin, there was obviously the possibility that they were not applicable to deposition of copper from commercial electrolytes that contain a variety of other substances in relatively small amounts. In particular, it was of interest to determine whether the presence of arsenic, antimony, or bismuth in the electrolyte would materially alter the behavior. Experiments have now been made under a variety of conditions with systems containing these cations, and the results are summarized in the present paper. Experimental Polarization measurements were made at 24.5oC in a Haring cell in the manner described previously.&apos; Electrolytes were made with doubly-distilled water, and contained 125 g per liter of copper sulphate and 100 g per liter sulphuric acid, both of reagent grade Eimer and Amend gelatin from a single stock was used throughout. Chloride ion was introduced as reagent grade sodium chloride, and arsenic, antimony, and bismuth by dissolving the chemically pure metal in hot concentrated sulphuric acid and adding appropriate amounts of the solutions to the electrolyte. Each cathode, of 1/16-in. thick rolled copper, was first etched in 40 pct nitric acid and washed thoroughly with distilled water. The surface was then brought to a standard condition4~9 by electrodeposition from an acid-copper sulphate electrolyte containing no gelatin, at a current density of 3 amp per sq dm for 30 min, followed by deposition at a current density of 2 amp per sq dm for l hr. As in previous studies, the cathode polarization eventually attained a steady-state value (15 to 75 min) such that further change in polarization did not exceed 0.2 mv per min. The polarization values recorded are those for the steady states. "Excess weights" were determined with arsenic and antimony present in the electrolyte, as the difference between the weights of the deposits obtained in the presence of these cations and those obtained in their absence, with the two cells connected in series. When gelatin was present along with the arsenic or antimony, it was also added to the electrolyte in the cell in series. Results and Discussion The results of the study are summarized in Figs. 1 to 6. From Fig. 1, top, it is evident that the presence of arsenic or antimony alone results in an increase of polarization, while bismuth alone causes a decrease. The presence of gelatin (25 mg per liter) rather drastically modifies all three cation effects, as indicated in the lower panels of the same figure. The addition of chloride ion, when no gelatin is present, causes comparable decreases in polarization in the presence of antimony and bismuth, but a relatively larger decrease when the electrolyte contains arsenic. It is interesting to note that the decrease in polarization brought about by addition of chloride when both arsenic and antimony are present parallels the behavior with arsenic alone, while the polarization in the electrolyte containing the cation mixture, without chloride added, corresponds to that for an electrolyte containing only the antimony cation. Similarly, the polarization at zero concentration of chloride in electrolyte containing arsenic and bismuth is that corresponding to an electrolyte containing arsenic alone. From Figs. 3a, 4a and 4b, it is clear that, in the presence of gelatin at a level of 25 mg per liter, the effect of chloride in the presence of arsenic and antimony, or a mixture of the two, becomes quite analogous to that observed in the absence of added cations. When both bismuth and gelatin are present (Fig. 5), the decrease in polarization with increased chloride concentration is virtually absent. This is perhaps a reflection of the large decrease in polarization brought about by the bismuth itself in the presence of gelatin. The shifts of the minimum in the polarization-chloride concentration curves brought about by changes of temperature (Fig. 3b), gelatin concentration (Figs. 3c and 4c) and current density (Fig. 3d) when the metal cations were present are all similar to the corresponding shifts observed in their absence." The approximately linear "excess weightv-anti-mony concentration relation recorded in Fig. 6 would seem to indicate that antimony is codeposited with copper to a considerable extent. On the other hand, only very limited amounts of arsenic appear to be adsorbed or codeposited.

Jan 1, 1954

lv. H. Blauvelt, Great Falls, Montana (communication to the Secretary): In his remarks on Mr. Stetefeldt&apos;s paper (Trans., xxiii., 587)) Mr. Goetz observes: " Trouble experienced with producers at Great Falls influenced me to try Taylor producers instead of those of Wellman. But recent reports show that the Wellman producers work better, besides coating nearly 50 per cent. less than Taylor producers of equal capacity. Indiana and Illinois coals cannot be used in the Taylor producers by reason of the large size and hardness of the clinkers which they form." I think that Mr. Goetz must have been misinformed regarding the work of this producer in Illinois. One of the large mauafacturing concerns in that State, the Illinois Zinc Company, situated at Peru, which uses a coal mined in the vicinity, tried one Taylor producer, some four years ago, in competition with those of an older type, which it had been using. As a result of this trial, the company has now thirteen Taylor producers, which have been in operation for about three years. A recent report from these works says that the Taylor producers have largely reduced the loss of coal through the grate, and have also improved the quality of the gas, as compared with that produced from the same coal in the producers of the older type. This Illinois coal is, perhaps, the worst in the country for making gas; since, besides containing from 20 to 40 per cent. of ash, it carries a large quantity of pyrites, so that the clinkers are large and extremely hard, and the capacity of the producer is most severely tested.

Jan 1, 1895

By Francis M. Walters

IN spite of the war and the preoccupation of many physical metallurgists with work on secret or confidential problems, definite progress was made during 1944 in our understanding of the behavior of steel and of the effect of alloying elements. During the first two years of the war there was much concern over the possible unavailability of certain alloying elements; this period saw the development of the N.E. (National Emergency) steels. However, the measures taken eased the alloy situation and currently, highly practical problems under study are the graphitization of low-carbon steel and weld-cracking, while investigations of more theoretical interest have concerned hardenability, isothermal reactions, the effect of hydrogen and the interpretation of the notched-bar impact test.

Jan 1, 1945

By David R. Mitchell

IF you are the owner of a mine, or a mine executive, or just an ordinary miner, and have a son about to go to college, do you urge him to take up mining engineering or do you try to dissuade him from such a course? If you live in the East, or the Middle West and your interest has been in coal rather than metal mining, the chances are that your young hopeful will be urged to do almost anything else rather than follow in father&apos;s footsteps.

Jan 1, 1939

By H. R. Page, A. E. Jr Lee

From the inception of zinc retorting on a commercial scale in the United States in 1890,&apos; the retort employed has undergone wide variations in its composition and manufacture, facilitating in part equally remarkable improvements in furnace capacities. The early day hand made clay retort was charged with carbonates or silicates or with coarse dead roasted concentrates mixed with a large proportion of charge fuel resulting in a relatively low zinc burden and fired 24 hr in direct coal fired furnaces. Its modern counterpart is fabricated in hydraulic presses from clay mixtures containing sizeable amounts of either silicon carbide or silica flour, charged with sintered flotation concentrates to more than three times the early day zinc burden and fired 24 to 48 hr in gas fired furnaces. This paper does not attempt to describe in detail the early day clay retort practice as it is well outlined in treatises by Ingalls,2 Lodin,3 Liehig,4 Hofman5 and others. A brief review of clay retort practice is presented together with a description of the major developments since 1912. Clay Retorts The Belgian type retort, both in the circular and elliptical forms, has been used almost exclusively. Typical dimensions of press made clay retorts around 1910 are shown in Table 1. Variations in these dimensions were used at different plants according to local conditions to a maximum inside diameter of 9 in. and inside length of 54 in. However, the effective heat penetration in a 24 hr firing cycle and the tendency of the retort to bend limited the retort size. Use of the elliptical vessel was an attempt to present a stronger cross-section resisting the tendency to bend and to increase the burden without increasing the depth of heat penetration. One exception to the 48-54 in. length was the 60 in. retort used as early as 1905 at Palmerton by means of supporting the last 12 in. at the butt end with a specially designed furnace back-wall. This backwall construction with the 60 in. retort had been developed and used at Bethlehem by G. G. Con-vers and A. B. DeSaulles. An attempt was made at Blende, Colo. to use even larger retorts of the Rhenish type based on European practice and requiring much higher furnace temperatures. Satisfactory plastic clays capable of withstanding these temperatures were not available, and the plant never operated successfully. PREPARATION OF BATCH Composition of the clay retort by weight was 40 to 50 pct raw clay and the balance "grog." Generally speaking the mix consisted of 7 parts plastic clay to 9 parts grog by volume. Principal source of the clay used was the Cheltenham vein—sometimes referred to as "St. Louis city clay." A typical analysis was A12O3-31.0 pct, SiO2-50.0 pct, Fe2O3-2.5 pct, MgO-0.3 pct, CaO-1.5 pct and loss on ignition 14.0 pct. At the smelter the clay was weathered whenever possible and then crushed to 0.08 in. or finer. Grog consisted of calcined adobies, cleaned retort scrap and cleaned refuse fire brick such as old furnace brick, blast furnace linings, and others. Saggers from ceramic plants and calcined flint clay were later used. The grog materials were ground to 0.12 m. or finer. Occasionally coke dust up to 10 pct of the mix was substituted for a part of the grog following European practice.² Particle size of the grog has a major influence on the retort properties—the larger the grain, the better can the retort withstand thermal shocks, resist bending at furnace temperatures and resist corrosion from slag; the smaller the grain, the lower the loss of zinc vapor through the retort walls. Grog forms the skeleton of the retort, and the clay shrinks around its grains to act as a binder. In the drying process, the grog has a stabilizing effect on the drying rate, decreasing shrinkage and giving up previously absorbed water to the surrounding clay to minimize the danger of cracking or checking.² Grog and clay were mixed through a horizontal pug mill with 10 to 20 pct water added, depending on whether the retort was to be formed by hand or mechanically, more water being required for the hand process. The batch or "mud" extruded from the pug mill was cut in convenient lengths for handling, stacked in piles or in special rooms, covered with wet burlap and allowed to "rot" or age from 1 to 8 weeks to increase plasticity. HAND MOLDING If the retort was to be molded by hand, the mud was repugged after the rotting period and given to the molders. Their molds consisted of 3 sheet iron or wood cylinders, each one third the retort length and defining the outer shape of the retort. Beginning with the bottom section, mud was placed in the form and tamped with a rammer

Jan 1, 1950

By C. E. Armantrout, J. A. Rowland, D. F. Walsh

THE close-packed-hexagonal structure of mag-J- nesium is converted to a ductile and malleable body-centered-cubic lattice by the addition of lithium in excess of 10 pct. Further, the density of magnesium or magnesium-base alloys is decreased by additions of lithium. The practical possibilities of such alloys as a basis for uniquely light, malleable, and ductile structural materials were pointed out by Dean in 1944&apos; and by Hume-Rothery in 1945.2 It was apparent to these investigators, however, that more complex compositions would be required if strengths sufficient for structural applications were to be developed in these alloys. In a search for strengthening additions, various investigators w have examined a number of the ternary and more complex alloys containing magnesium and lithium. An investigation of the fundamental characteristics of these alloys was undertaken by the Bureau of Mines. The investigation was initiated with a study of the magnesium-rich corner of the equilibrium diagram for the ternary system, Mg-Li-Al. The following data from published investigations of Mg-Li-A1 alloys were available: 1—a description of isothermal sections at 20" and 400°C through the Mg-Li-A1 constitution diagram by F. I. Shamrai;&apos; 2—a diagram by P. D. Frost et al." showing approximate phase relationships at 700°F for a number of the Mg-Li-A1 alloys; and 3—diagrams showing the constitution at 500" and 700°F for the Mg-Li-A1 alloy system published by A. Jones et al.&apos; Where compositions and temperatures permit comparison, these diagrams show disagreement. The 700°F isotherms of Frost and Jones differ only in the placement of the phase boundaries. But Sham-rai&apos;s 400°C (752°F) isotherm shows a variation in phases as well as in phase boundaries. Although rigid comparison of these different isothermal sections might not be justifiable, it seems impossible to reconcile Shamrai&apos;s construction with the isotherms of Frost or Jones. The isothermal sections presented in this paper were prepared to determine compositions which might be suitable for age hardening and to develop the general slope and placement of the various phase boundaries in the magnesium-rich corner of the diagram. Sections at 375", 200°, and 100°C were selected for investigation. In constructing these sections, the solubility of aluminum in magnesium, as reported by W. L. Fink and L. A. Willey Vn 1948, was used at the binary Mg-A1 boundary and the solubility of lithium in magnesium was obtained from the equilibrium diagram for that system as reported by G. F. Sager and B. J. Nelson" in the same year. The solubility of magnesium in lithium was determined experimentally and conforms in general to data reported by P. Saldau and F. Shamrai." Parameters for AlLi and MgI7A1, were taken from American Society for Testing Materials X-ray diffraction data cards. Experimental Procedures Although the isothermal sections presented in this paper are not unusually complex, the experimental techniques involved in their construction are made extremely difficult by the relatively high vapor pressure of lithium and the great chemical activity of both magnesium and lithium. Because of these characteristics, which make precise control of the composition of equilibrium-treated filings practically impossible, the disappearing phase method was used in preference to the parametric method in conjunction with metallographic studies. The alloys used in this investigation were melted and cast in an atmosphere of helium using a tilting-type furnace which enclosed a steel crucible and mold in a single unit. Each portion of the charge (500 to 600 g) was cleaned carefully just before placing it in the crucible; and the charge, crucible, and entire melting apparatus were evacuated and then washed with grade A helium while preheating to approximately 100°C. The alloys were melted and chill cast in an atmosphere of helium. Alloys prepared in this way were relatively free from inclusions and a fluxing treatment was considered unnecessary. The cylindrical ingots obtained were scalped and then reduced 96 pct in area by direct extrusion, yielding % in. diam rod. Sections of the rod, approximately 3 in. long, were given equilibrium heat treatments and then sampled for metallographic examination, X-ray diffraction study, and chemical analysis. The surface of each equilibrium-treated rod was machined to a depth sufficient to insure removal of contaminated material before samples for chemical analysis or X-ray diffraction study were obtained, and all decisions on microstructure were based on the examination of the central portion of the metallographic specimen. All specimens homogenized at 375°C were analyzed after this equilibrium heat treatment. When the composition of an alloy placed it in a critical area of the 200" or 100°C isothermal section, a check chemical analysis was made on a sample taken from the alloy specimen as-heat-treated at the particular temperature. Standard chemical procedures of gravimetric analysis were used in the determination of magnesium and aluminum; lithium, potassium, and sodium were determined by flame photometer methods

Jan 1, 1956

By Milton Glicken

THE airborne geophysicist is a busy man these days. In his plane he may have the airborne magnetometer, the airborne scintillation counter, and the airborne electromagnetic surveying system. Each of these is an independent tool, but all require additional auxiliary equipment for locating the aircraft in space: recording altimeters and Shoran or aerial cameras. Now there is still another piece of equipment, the airborne magnetic gradiometer, an accessory to the magnetometer. To understand its uses, consider the function of the magnetometer itself. Aside from detecting magnetic ore, the airborne magnetometer finds greatest use in spotting intrusions of igneous material. Where there is enough contrast in magnetic susceptibility of igneous rock and adjacent formations, it outlines the intrusion. Certain minerals also influence the magnetometer directly, but with the exception of magnetite and possibly one or two others, their effect is weak and can be detected only when there is sufficient ore and the magnetometer flight passes very close to it. An igneous intrusion of infinite depth with vertical sides is represented on a magnetometer record by an anomaly, as in Fig. 1. Amplitude of the high depends on susceptibility contrast of the igneous rock. Generally speaking, the edge of the intrusion lies below the point of inflection of the curve, and this point, where the curvature changes from positive to negative on the magnetometer profile, would be near A in Fig. 1, with a counterpart, of course, on the other side. Location of the contact is one of the principal objects of the survey, but finding the precise point is not always easy, as inspection of the curve near A will show. Mineralization is often found at the contact zones, as at B. Magnetic effects, if detected, may be small, as in B&apos;, and when superimposed on the anomaly due to the instrusion they are very difficult to discern and analyze. Furthermore, if these small fluctuations are to be perceived by the magnetometer the vertical scale should be large. This increases the slopes of the anomaly and makes detection of small deviations and inflection points even more difficult. The airborne magnetic gradiometer was designed to help overcome these difficulties. What it presents is the first derivative of the magnetometer record with respect to time, that is to say, the slope at any point. Fig. 2 represents an actual magnetometer record (solid line) with the corresponding gradiometer record (dashed line) superimposed. Both records read from right to left. Vertical lines on the original magnetometer record are automatic steps designed to keep the pen from going off scale. The slope of any curve is greatest at the point of inflection or point where the curvature changes sign, and this point is a maximum (or minimum) on the gradi- ometer. The chief advantage of the gradiometer is that maxima or minima are much easier to see and to locate precisely; hence an accurate location for the point of inflection can easily be found. Note that points C and D are more sharply defined than C and D&apos;. Similarly the small fluctuations of the original record, so important to the interpreter, are far more clearly shown at E, F, and G, than on the original record at E&apos;, F&apos;, and G&apos;. Though not necessarily highs and lows on the gradiometer, they do show up clearly what would take a painstaking analysis to detect on the original magnetometer record. Will the gradiometer have a particular configuration which indicates an orebody? Not necessarily. The total intensity curve, or original magnetometer record, can display an orebody in various ways, depending on dimensions, orientation, latitude, and composition, as well as on direction, flight height, and instrumental sensitivity of the traverse. Where the total intensity can take on so many different shapes the gradiometer must vary too. It is generally recognized that interpretation of total intensity magnetometer records requires an expert analysis; the gradiometer can be of considerable assistance to the expert but it does not replace him. Mechanism of the gradiometer is simple. A Leeds & Northrup recorder in the aircraft records the magnetic gradient simultaneously with the total intensity, which is on another recorder. Fiducial marks are put on both records simultaneously and the speed of the paper through the recorders is kept the same on both. This makes it possible to place one record over the other for direct comparison. In the laboratory the flights are positioned on a map. Maximum and minimum points on the gradiometer, which can then be posted on the map at their proper locations, may be expected to fall along a trend crossing the direction of flight. Trends should indicate the edge of an intrusion, or some other important features, and when superimposed on the total intensity contour map help greatly to locate the points of inflection, or line of zero curvature.

Jan 1, 1956

By Jerome Strauss

IN his review of developments in 1943, Gilbert Seil, Chairman of this Committee on Reduction of the Ferroalloy Ores, tabulated the consumption of the alloying metals in relation to the steel production of that year. In the year just closed the approximate tonnage was of the same order, differing only to a minor degree or suffering some correction with more precise figuses available, as indicated in the following estimates: Consumption Metals in Tons Steel 92,000,000* Manganese 700,000 Silicon 200,000 Chromium 200,000 Nickel 75,000 Molybdenum 20,000 Tungsten 8,000 Vanadium 1,700 Titanium 1.600 Boron 10 `Production figure. The technologic studies instituted during 1942 and carried forward with such great vigor during 1943 continued into 1944 although in some instances were brought to a close either by completion of the specific development

Jan 1, 1945

By C. K. Leith

CERTAIN ideas on iron and steel sanctions to follow originated in a series of conferences held under the joint auspices of the War Department and Brookings Institute in Washington last spring. The views presented may be regarded as those of substantial segments of the steel industry. In view of the fact that steelmaking capacity can be so quickly converted to the production of armament, any effective control must necessarily include the entire steel industry and not solely the parts devoted to the production of implements of war. It must also be exercised all the way from production and shipment of raw materials through their ultimate conversion into finished products and use. Control will be dis- cussed under two main headings: (I) control of raw materials at the source; (2) control of steel capacity within the Axis countries.

Jan 1, 1944

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter&apos;s interesting paper which appear to require explanation, if not modification.

Jan 1, 1901

By T. Egleston

THE direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German bloomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Not¬withstanding the improvements which have been made in the construction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The Dame of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process. * Read at the Montreal meeting, September, 1879.

Jan 1, 1880