Search Documents

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By Sergio N. Monteiro

Wastes generated by our society and the question on how to dispose them is, nowadays, a relevant matter of concern. The objective of the present work was to characterize the technical properties of composites made of discarded jute sackcloth with its coarse wove fabric, serving as reinforcement phase, and polyethylene wastes collected from city dumps, as continuous matrix. Different amounts, up to 30 wt.% of jute plain weave, fabric were press molded at 160°Ctogether with sieved polyethylene particles. The resulting composites displayed mechanical properties that could compete with those of low-density wooden board. Both by presenting a solution to, otherwise, disposed wastes and by helping to prevent deforestation, the investigated composite may be regarded as an environmentally correct material.

Jan 1, 2006

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Esher Hsu

In Taiwan, around 8,000 tons of batteries are consumed per year but only 17% of which were collected and transported to oversea for recovery. The dumping used batteries have become a potential environment problem. How to increase the collection efficiency of used batteries is an important issue for EPA in Taiwan. Besides, some treatment plants are on process to get permission for recovering used batteries. The objective of this study is to estimate the recycling cost of spent consumer battery and explore the feasibility of recovering used consumer batteries in Taiwan based upon the principle of cost-efficiency. The recycling cost including collection cost and recovery is estimated based on a survey. Results would provide some suggestions to Taiwan EPA regarding feasibility of recovering used batteries in Taiwan.

Jan 1, 2006

By Xi Zhang

A technique for fabricating free-standing, high-aspect-ratio porous and pillar-type Ni structures has been developed using wet Si processing. A wafer of (100) Si was initially etched in HF solution to form deep pores with micron-sized diameter. The aspect ratio can exceed 200. By introducing the as-etched Si into a defined aqueous Ni2+ solution, Ni deposits grew rapidly onto the sidewalls and replaced the Si. Long-time immersion allows the Si sidewalls to be completely converted and thus form a metallic Ni structure with high-aspect-ratio pores. It is known that close-packed submicron Si pillars can be formed by oxidizing and subsequent etching of the macropore sidewalls. Treated in the same Ni solution, high-aspect-ratio Ni pillars were correspondingly emerged by replicating the original pillar-type Si structure.

Jan 1, 2006

By David Arana

The use of gas-water dispersion of a molten material flow onto a vibrating surface is developed as a process to minimize water pumping requirements, minimize the risks of explosions, and minimize the post solidification dewatering and fines handling equipment requirements. The process uses existing vibration transport technologies and common plant utilities. Plant trials using the smaller footprint and the progressive molten particle cooling time have yielded encouraging results. The results are analyzed and reported.

Jan 1, 2006

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By Javier Enrique Basurco Cayllahua

In this work, a gram-positive bacteria was used as biosorbent to elucidate the aluminum load capacity under different conditions related to metallurgical and chemical plants. The sorption data followed the Langmuir, Freundlich, Dubinin-Radushkevich isotherms. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Dubinin-Radushkevich model fits better the aluminum biosorption data. The maximum sorption capacity was found to be 41.59 mg.g-1. The maximum removal of aluminum was 95% at pH around 5. The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). This study indicated that the R. opacus is an environmental friendly biosorbent.

Jan 1, 2009

By Patricia Martínez Nicolás

Nickel and ferronickel are some of the major components in the production of special alloys; however, the energy consumption for their production greatly increases their price. A cheaper option could be to use NiO and a reducing agent. This work presents experimental and theoretical analysis to estimate the effect of slag basicity and amount of reducing agents on the NiO reduction from the slag which interacted with molten steel at 1600 °C in an EAF. The slag system contained CaO, SiO2, CaF2 and NiO together with a reducing agent, ferrosilicon or carbon. The NiO content in the slag was 25 mass%. The amounts of the reducing agents (Si and C) were 1 to 4 times the stoichiometric mass to reduce NiO. The CaO/SiO2 ratio was 1.5 and 2.5. The kinetics of the process was very fast since after few minutes the maximum nickel yield was obtained. The slag basicity had a negligible effect on the reduction of NiO.

Jan 1, 2006

By Manis Kumar Jha

Leaching studies were carried out for the recovery/ recycling of metals from PCBs containing 17.05% Cu, 0.74% Ni, 1.74% Fe, 4.35% Pb and 8.32% Sn using various acids such as H2SO4, HCl and HNO3. While sulfuric acid was not a suitable leachant for the dissolution of metals from PCBs, hydrochloric acid selectively dissolved tin. The nitric acid was found to be effective lixiviant with the recovery of 99.99% Cu, Fe, Ni and 36.7% Pb in 6M HNO3 at S/L ratio of 100 g/L and 90oC. The kinetic studies carried out with 2M and 4M HNO3 at 90oC showed ?Ash diffusion control dense constant size-spherical particles? model.

Jan 1, 2010

By María Cristina Ruiz

Enargite rich copper concentrates can not be treated by conventional smelting/converting technology and thus nonconventional methods such as leaching must be used. Since enargite (Cu3AsS4) is a hard to dissolve mineral in acidic solutions, pyrite, a common impurity in copper concentrates, could be used to increase the enargite dissolution rate. On this matter, we present in this work experimental data on the pressure leaching of a mixed enargite-pyrite concentrate in H2SO4-O2. The results show that the dissolution of enargite from the mixed concentrate is considerably faster than the dissolution of pure enargite mineral. The leaching rate increases significantly with temperature. Over 98% of enargite was dissolved in leaching 64 micron size particles at 200 ºC and 100 psi of partial pressure of oxygen in just 30 minutes. A change in the partial pressure of oxygen from 50 to 150 psi showed also a large influence in the leaching rate.

Jan 1, 2010

By Nam-Il Um

Bottom ash contains several ferrous materials (ferrous metals, Fe3O4, Fe2O3, FeS, etc.). In particular, ferrous metals contain heavy metal because Ni and Cr are chemically attracted to iron. Likewise, Cu is used to coat Ni and Cr metals as polish or to prevent corrosion. In this study, an Fe3O4-Fe2O3 double layer (similar to pure Fe) was found to have been formed in ferrous metal during air-annealing in an incinerator (1000°C). A strong thermal shock such as one that occurs during the water-cooling of bottom ash results in the breakdown of this oxidation layer, facilitating the degradation of ferrous metals and formation of corrosion products. Therefore, Fe-ion (heavy metal) oxides may be formed on ferrous metals and may be separated from bottom ash via magnetic separation. This study sought to investigate the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion (heavy metal).

Jan 1, 2006

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

By Khandaker M. Anwar Hossain

This paper presents the development of lightweight concrete (LWC) incorporating pumice aggregate and volcanic ash (VA) based ASTM Type I blended cement (PVAC). Fresh and mechanical properties of LWC mixtures such as slump, air content, compressive strength, tensile strength, density and modulus of elasticity are described. The durability characteristics are investigated by drying shrinkage (DS) and water permeability. The investigation suggests the production of LWCs incorporating blended PVAC and VPA having satisfactory strength/durability characteristics for structural applications. The use of PVAC induces the beneficial effect of reducing drying shrinkage and water permeability. Development of such non- expensive and environmentally friendly LWCs with acceptable strength and durability characteristics is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.

Jan 1, 2010

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By Susan Jacob

The heat of fusion of silver was measured using high temperature differential scanning calorimetry (HTDSC). Heating rate, sample mass, calibration standard and cover gas flow rate were varied to determine their impact on instrument accuracy and reproducibility. Good reproducibility was achieved in most of the runs. Accuracy was not satisfactory in most of the runs, though three runs gave results within 1.7%, 3.3% and 3.5% of the literature value, within the acceptable limits. A larger mass and higher heating rate tend to generate more accurate results.

Jan 1, 2006

By Dirk van Zyl

As part of the North American regional activities during the Mining, Minerals and Sustainable Development Project (MMSD) one project focused on the development of sustainability evaluations at the operations level. Engagement was identified as one of the seven important questions to be addressed. Engineers and scientists employed in the mining, minerals and materials production arenas must understand the importance of stakeholder engagement, both within and outside the operations as it is essential in the ongoing activities required to contribute to sustainable development. After developing the awareness that a social license can only be contemplated if engagement is in place, they also have to develop skills in engagement processes. This presentation will present the business case for engagement as well as an approach to motivate undergraduate mining engineers to embrace it. The presentation will also review some recent and ongoing research to improve the engagement process.

Jan 1, 2010