Search Documents

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By A. M. Gaudin

Introduction The discovery of artificial radioactivity, that is, of radioactivity of acorns other than those which are naturally radioactive, has increased vastly the possibility of using radioactivity as an analytical cool. The incomparable value of radioactive atoms, which are commonly termed tracers, arises from the extreme sensitivity of this analytical method. To get an idea of this extreme sensitivity it may be useful co recall that gravimetric analytical methods will not permit the weighing of anything much lighter than one-hundredth of a milligram of material. Under the most favourable circumstances, this represents an uncertainty in the answer of 1016 acorns, or 10,000,000,000,000,000 acorns. Accurate spectrographic methods possibly have a sensitivity 10,000 times greater than this, but the uncertainty is still of the order of 1012 atoms. The tracer permits ascertainment of decay of a single atom so that its sensitivity, without half trying, can be several orders of magnitude greater than that of any other method available co chemists. In addition co the sensitivity of tracers to which reference has just been made, tracers have another property which makes them unique. A radioactive atom is almost exactly like the corresponding non-radioactive acorn m regard to its electronic structure, and therefore in regard to its chemical properties. The nucleus is different, but the nucleus does not participate in chemical reactions. Therefore, a tracer acorn behaves like an ordinary atom until such time as its nucleus undergoes a catastrophic decay. This unique property permits one to use tracer acorns as atomic spies and therefore to follow the behaviour of acorns of a certain kind among their own kind. In other words, the tracer method permits us to study and measure what we call self-diffusion. All of the uses of tracers that have been made depend on the two properties co which reference has been made.

Jan 1, 1949

By C. Prévost, V. Leclerc, R. Pinto, M. Ruel

"A buffer’s ability to dampen production variations is directly related to its size. Small buffers cannot handle large variations in production, resulting in production losses when their inventory is depleted or saturated. This paper presents a predictive control algorithm used to regulate the inventory in a buffer of limited size, subject to large production variations caused by an upstream batch process. The algorithm was designed to manage the acid flow rates in an acid regeneration process, servicing batch leach reactors at Rio Tinto Fer et Titane, in Sorel-Tracy, Québec. The objective was to increase production by reducing equipment downtime caused by imbalances in the acid tanks servicing the leach reactors. The controller attempts to maintain acceptable acid tank volumes by optimizing the leach reactors acid/slag ratio and reaction time as a function of anticipated acid needs, all while maintaining product quality.INTRODUCTION Some beneficiation processes in extractive metallurgy require processing bulk material in batches. Typical examples of metallurgical beneficiation batch processes are smelting, leaching, electrowinning, elution and carbon-in-pulp. These processes are often situated midstream in an ore beneficiation flow sheet and either receive or transfer ore to continuous processes. Batch processes, by their very nature, introduce large variability in the flow sheet, because they process large finite quantities of material at nearly periodic time intervals. In order to dampen variations in production, various buffers–tanks and stockpiles–are utilized to accumulate ore upstream and downstream of batch processes. A buffer’s ability to dampen production variations is directly related to its size (Phillis & Gumede, 2011). Small buffers cannot handle large production variations, resulting in equipment downtime when their inventory is depleted or saturated (Everett, 2010, Berton et al., 2013). Consequently, the batch equipment production rates must be adequately managed to minimize production losses, attributed to depleted or saturated inventories, while maintaining product quality. Algorithms that anticipate or predict future production variations are often utilized to regulate buffer inventories, subject to large flow rate variations (Salvo et al., 2002; Bonvin, 2013). This paper presents a predictive control algorithm used to maintain an acceptable volume in a spent acid tank servicing several batch leach reactors. The algorithm is implemented at the acid leach plant of Rio Tinto Fer et Titane, in Sorel-Tracy, Québec."

Jan 1, 2017

By L. Li

Iron removal is a common procedure in hydrometallurgy of non-ferrous metallic ores. Chemical precipitation and solvent extraction are currently the main methods employed for separation of iron from copper leach solution. However, chemical precipitation methods have the problem of producing large amounts of iron precipitates, and/or requiring high temperature and high pressure conditions for precipitation. The precipitates are difficult to separate from the solution. Emulsification is a general problem for solvent extraction, which causes loss of extractants and contamination of the electrolyte. A common problem for solvent extraction and chelating ion exchange processes is the difficult iron stripping process. Therefore, finding an efficient and environmentally friendly method for iron removal is of great significance. In this paper, new processes of using ion exchange resins to remove iron from copper leach solution have been investigated. Salicylic acid, amino carboxylic acid, amino phosphonic acid and hydroxy-oxime resins were employed to adsorb iron from a simulated copper leach solution containing 40 g/L of Cu2+ and 36 g/L of Fe3+. It was found that a hydroxy-oxime resin, named Z-Fe, has excellent adsorption selectivity on Fe3+. Desorption behavior of the resin was studied by two step elution using dilute H2SO4 and oxalic acid solution, respectively. After optimizing the adsorption-elution processes, the extent of removal of iron from the simulated copper leach solution using resin Z-Fe was 90%, while copper recovery could reach 100% in closed circuit processing.

Jan 1, 2016

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By J. E. Moyle

The costs of labour and electric power are of prime concern to almost all industrial enterprises, and various methods of reducing their impact on production costs are constantly being developed. Automation is one of these schemes, and has received a good deal of attention in the past few years. In the mining industry, compressed air is almost universally used, and its cost is significant. Although the compressor machinery now in use has achieved a high degree of development, the hazard of explosion and fire still exists in these systems. There is thus considerable resistance in some quarters to suggestions that such installations can be safely and successfully automated. The Milliken power plant consists of two 30,000 lb. /hr. fully equipped high-pressure boilers, four H.P. air compressors, a steam turbine for stand-by power, and several L.P. compressors and vacuum pumps. With the installation of automatic and protective equipment in the machinery section, the shift force has been reduced from three to two men.

Jan 1, 1963

By J. Basi, J. A. Finch

ABSTRACT Testing the effects of bubble size (Db) in a Mo cleaning ?otation column at Highland Valley Copper mine indicated that increasing the proportion of small (< 1 mm) bubbles signi?cantly improved column metallurgical response, compared to typical operation. The results were a three- to four-fold Mo recovery increase and a 1 to 2% Mo (absolute) concentrate grade increase. The improvedcolumn operation produced a 4% Mo plant recovery increase. This study also showed that modelling the ?otation rate constant (k) as an inverse square function of Db was more accurate than considering k to be inversely proportional to Db.

Jan 1, 2010

The principles and utility of in-situ coal gasification are discussed, and a first field test conducted by the Alberta Research Council in 1976 near Forestburg, Alberta, is described. The test was carried out in a 12-ft subbituminous coal seam under 60 feet of cover. Within this seam, a 30 by 60-foot block , containing approximately 650 tons of coal, was delineated by four injection/production holes which were oriented to take advantage of the natural fracture system in the coal. Linkage between holes was established by reverse combustion and gasification was accomplished by injecting air into the ignited coal. No steam was injected but operating pressures were adjusted to utilize formation waters for partial carbon -steam gasification. The coal gasification runs lasted six weeks and gasified an estimated 900 tons of coal ,&apos; during sustained periods of gasification, a fuel gas with heating values of between 110 and 150 Btu/scf was obtained. Plans are now being developed for excavating the test site and inspecting the subsurface cavities created by gasification.

Jan 1, 1977

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005

By J. Schmidt

The development of set of laboratory experiments, intended to help undergraduate students meet Canadian Engineering Accreditation Board requirements for Engineering Design outcomes, is described.The laboratory, which is part of a third year level course in hydrometallurgy, is aimed at advancing the ability of students to generate and use experimental results to design an industrial copper leach/SX/EW plant. Emphasis is placed on the students demonstrating the ability to use of their engineering knowledge in weighing the pros and cons of the various process options that they test in converging to a final flowsheet. INTRODUCTION Over the past number of years the Canadian Engineering Accreditation Board, CEAB, has dramatically shifted the way that they evaluate undergraduate programs. In the past, the focus was on measuring of the quantity and quality of material the students were intended to learn as well as the methods and resources used to deliver that material. Now, rather than principally evaluating the inputs of programs, the focus is more on measuring the quality of the outputs from the programs, i.e. the quality of graduating students. In this regard, the CEAB has developed a list of twelve attributes that learners must develop in the course of their studies. Engineering programs must, not only demonstrate that their curriculums provide opportunities to develop these attributes, but must measure student proficiency in each of these attributes as they progress toward graduation. One particular graduate attribute that Laurentian University’s Bharti School of Engineering has encouraged its faculty members to develop content for is “design”. Engineering Canada (2018) defines this attribute as “an ability to design solutions for complex, open-ended engineering problems and to design systems, components or processes that meet specified needs with appropriate attention to health and safety risks, applicable standards, and economic, environmental, cultural and societal considerations”. The previous laboratory component for the hydrometallurgy course was a collection of unconnected experiments covering leaching, solvent extraction, ion exchange, and electrowinning. Like in other undergraduate courses, students would perform stand-alone experiments, make the specified measurements, do the specified analyses of the results, and report the findings, all as strictly detailed in the lab manual. The vision for the new lab was to create an experience that would more closely mimic an industrial research program whereby students would start with a given feed material and would progress through a series of connected experiments. Emphasis is placed on the student demonstrating competency in, not only, generating and analyzing experimental data, but also in using the data along with their engineering knowledge to design and evaluate the pros and cons various plant configuration options. Principally, students are asked to weigh cost, safety, and environmental concerns in converging to their final flowsheet. In designed the leach circuit, students must weigh the costs/benefits of varying leach temperature. Higher leach temperatures will yield faster and more complete copper dissolution, which will allow for the specification of relatively smaller leaching circuits, saving capital costs. However, hotter acid solutions are more dangerous to handle and require increasing amounts of energy to heat the slurry, increasing operating costs. In solid/liquid separation, students must weigh the pros and cons of the addition of a flocculent to assist settling. The flocculant will allow for the design of a thickener circuit that employs units with a relatively smaller area, but will result in a thickener underflow with a lower pulp density, which may necessitate a larger number of thickeners. In addition, the environmental concerns of producing a tailings product that contains an organic contaminant should be addressed. In solvent extraction, students must specify the number of stages of loading and stripping, as well as organic and aqueous flowrates to produce suitable raffinate and rich electrolyte streams. Finally, in electrowinning, students will compare the costs/benefits and risks of the use of precious metal coated titanium dimensionally stable anodes (DSAs) versus conventional Pb based anodes.

Jan 1, 2019

By George E. Cole

"It is a truism that the metals, and particularly the precious metals tend to monopolize the attention of those interested £n the mineral industry. This is a tendency to be mildly, but actively and continuously combatted if we are to have a well-rounded mineral development." There are in the province of Ontario a number of industries centred about the non-metallic minerals. Too little is heard of the part these play in our industrial life. It is with the intention of showing what the gypsum industry is doing in Ontario that this paper is written. The writer lays no claim to any originality in the discussion and merely offers some material in an endeavour to assist in bringing about that &apos;well-rounded mineral development&apos; sought for Ontario. M. Y. Williams in his "The Silurian Geology and Faunas of Ontario Peninsula and Manitoulin and Adjacent Islands"1 in discussing the industries dependent on the Silurian rocks of south-western Ontario points out that "the splendidly ordered gypsum mine at Caledonia, formerly owned by the Alabastine Company of Paris, and now owned by the Ontario Gypsum Company, is a revelation to the average man, who disconnects mining entirely with this part of Ontario". This region is better known as one of the richest and most thickly settled agricultural areas in Canada.

Jan 1, 1925

By Takashi Nakamura, Atsushi Iizuka, Yong Fan, Etsuro Shibata

The level of iron in typical copper slag reaches nearly 40% by mass, in the form of iron silicate. We designed a method to oxidize the nonmagnetic iron silicate to magnetite, permitting the selective recovery of the slag’s iron content by magnetic separation. This would effectively decrease the volume of dumped slag; the reclaimed iron could be used for iron and steel making. The crystallization behaviors of magnetite and hematite were studied as reaction products of the molten oxidation of copper slag. A gas atmosphere of 1% by volume of oxygen was found to effectively precipitate the slag’s iron content as magnetite.

Jan 1, 2015

"This paper deals with the reconciliation of open stope performance at Olympic Dam, South Australia, with a focus on stope stability, recovery, and operational aspects of stope reconciliation in relation to the expected or planned stope design. The observed stope performance is inconsistent with the equivalent linear overbreak sloughing criteria for assessing the performance of large open stopes. The aim is to investigate new stope performance criteria using quantitative (overbreak, underbreak, maximum depth of wall failure) and qualitative (stope productivity, observed fragmentation) information that correlates with the observed stope behaviour, providing a process for improving future stope designs.RÉSUMÉ Le présent article traite de la réconciliation de la performance des chambres ouvertes à Olympic Dam, Australie du Sud, en ciblant la stabilité des chambres, la récupération et les aspects opérationnels de la réconciliation des chambres par rapport à la conception attendue ou planifiée des chambres. La performance observée des chambres ne concorde pas avec les critères d’épaisseur équivalente du bris hors profil pour évaluer la performance de grandes chambres ouvertes. L’objectif est d’étudier de nouveaux critères de performance des chambres au moyen de données quantitatives (rupture hors profil, rupture à l’intérieur du profil planifié, profondeur maximale d’effondrement du mur) et qualitatives (productivité de la chambre, fragmentation observée) qui concordent avec le comportement observé des chambres, fournissant ainsi un processus pour améliorer les futures conceptions des chambres."

Jan 1, 2015

By D. C. R. Espinosa, P. Aliprandini, F. P. C. Silvas, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel ores are divided into two types: sulfide deposits and lateritic deposits. About 60% of nickel resources are found in laterite ore, while the remaining 40% is contained in sulfide ore. Laterite ore is usually processed via pyrometallurgical means or through hydrometallurgical techniques that include acid leaching and metal value recovery from solution. In this study, copper and nickel adsorption by Dowex M4195 ion exchange resin from an acidic sulfate liquor was investigated. The acidic sulfate liquor was collected from an atmospheric leaching process (AL) of laterite ore. Ion exchange experiments were conducted in a batch system by varying parameters such as pH, time, metal concentration and temperature. Initially, mono-elemental synthetic solutions of nickel and copper were used in the experiments and then a synthetic solution simulating AL liquor was tested. Test results showed that the resin exhibited high selectivity towards copper and nickel, however, a high concentration of iron in the synthetic AL solution interfered with the recovery of nickel and cobalt by the resin.INTRODUCTION Nickel is one of the most important industrial metals in the world. It is widely used in industrial applications, such as the production of stainless steel, magnets, electroplating and special alloys (Dizge et al., 2009). The main sources of industrial nickel production are sulphide deposits; only 40% of industrial production uses lateritic ores. However, it is estimated that 60% of global nickel resources are found in nickel laterite deposits (Kuck, 2016). Since industrial nickel demand continues to grow, the development of new technologies for the extraction of nickel from laterite ores has become an interesting research topic (Agatzini-Leonardou, 2009)."

Jan 1, 2017

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

The introduction consists of back-ground information, of an historical and statistical nature, relating to the Thompson mine. The geological presentation is based on illustrations that are intended to provide a progressively closer look at the ore occurrence. The illustrations consist of an index map, a geological map of a 15-by 85-mile area including the Thompson mine, a series of four maps dealing with the geophysics and geology of a 6-by 4\f.j-mile area at Thompson, a mine level plan and corresponding section, two sto11e 11lans and corresponding sections, and photo-graphs and photomicrogra11hs of the various one types. T HE Thompson mine is located about 400 miles due north of Winnipeg. The ore deposit was dis-covered in February, 1956. Five years later on March 25, 1961, the Thompson production facilities were officially dedicated with the shearing of the first nickel produced at the Thompson refinery. Full production, at an annual rate of more than 75,000,000 lbs. of refined nickel, was attained later in the year.

Jan 1, 1963