Search Documents

By C. D. McMaster, John C. Hartley

Three systems that monitor ventilating fans are described . These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown .

Jan 1, 1964

By G. W. Jones

[A survey of the literature relating to ignition temperatures of acetylene-air and acetylene-oxygen mixtures reveals rather wide disagreement in the reported results. In some instances the ignition temperatures of acetylene-air mixtures were reported to be lower then those of acetylene-oxygen mixtures, which is contrary to experience with other combustibles. To clear up some of the reported discrepancies, the authors have investigated the ignition temperatures of acetylene both in air and oxygen, and their results are presented in this report.]

Jan 1, 1941

By Mark Flower

A 20L ignition test chamber has been used to test suspensions of 7 UK and world traded coals in air and O2/CO2 mixtures typical of oxy-combustion conditions. The coals varied in rank from sub-bituminous to bituminous and were tested in varying concentrations from the ignition limit to 400g/m3. Following each successful test the combustion residue was collected, weighed and analysed within a thermogravimetric analyser, allowing Q factors to be estimated. The ignition limit varied slightly in air, but was mostly around the 200g/m3 level. With the exception of Coal C, which was much harder to ignite, it correlated roughly with coal rank. The ignition limit changed significantly with O2 concentration when in mixed O2/CO2 gases. Only a few high volatile coals ignited in 21% O2/CO2 v/v, and then only with a 2500 J, rather than a 1000J, igniter. An increase in O2/CO2 levels to 30 or 35% gave ignition patterns similar to those carried out in air with a further increase to 40% having little additional effect. In addition the minimum ignition concentration decreased with increase in O2. Heterogeneous combustion or gasification of the coal by CO2 appears to be confirmed by comparing weight loss results for air and O2/CO2 mixtures respectively for an equivalent peak pressure rise.

Jan 1, 2009

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By James Pennington

[The Mining and Metallurgical Divisions of the Bureau of Mines, Region V, conducted an investigation in 1950-51 of the iron sulfide deposits in Aitkin and Carlton Counties, Minn. Twelve diamond-core-drill holes, aggregating 2,347 feet, were drilled in secs. 14 and 15, T. 46 N., R. 25 W., Aitkin County, to increase reserves of iron sulfides known to exist 2 miles southwest in secs. 28 and 29, T. 46 N., R. 25 W. Three diamond-core-drill hobs, totaling 561 feet, were drilled in Canton County, sec. 7, T. 46 N., R. 2 0 W., to check reports of the presence of a large sulfide deposit in that area. Mineral-dressing tests were made on cores from 10 holes drilled in Aitkin County. These included core from hole 21 drilled in sec. 28 and submitted by the Glen Development Co.]

Jan 1, 1953

By John W. Cole

The Butte district has been the principal producer of metallurgical-grade manganese in the United States since World War I. Manganese dioxide nodules are produced from rhodochrosite ore by concentrating the rhodochrosite and roasting the concentrate in rotary "cement-type" kilns. The Anaconda Copper Mining Co. is the only producer at present. Under the stimulus of a purchasing program administered by Metals Reserve Company during World War II, however, several independently owned or operated mines (including the Norwich) produced manganese carbonate ore. These mines were examined in Juno 1949 by John W. Taber, mining engineer, Bureau of Mines. A core-drilling program to develop ore in the Norwich mine was recommended and approved. drilling was completed early in 1950. This report gives factual data obtained.

Jan 1, 1951

By Scott W. Hazen, George W. Gladfelter

This report presents the results of an initial investigation into some problems resulting from the use of assays representing unequal sample interval lengths and the use of the weighted average grade of ore in evaluating bedded mineral deposits . A mathematical proof and examples are given to show that the unweighted and weighted assay averages are equivalent when there is no correlation between assay value and sample interval length but that these averages are different when there is correlation between assay value and sample interval length . The amount of this difference between estimates is a function of the degree of correlation . One set of sample and assay data , based on 11 stratigraphic sections of the Phosphoria formation in Idaho , indicates that the relationship between the amount of difference between estimates and the correlation factor is approximately linear . If this correlation relationship can be established , within acceptable limits of precision , as a consistent attribute of deposits , the estimate of weighted average grade of ore could be predicted directly from the unweighted estimate of grade of ore by using the relationship as a prediction factor . Randomness tests on the sample and assay data from the Phosphoria formation , using the mean - square - successive - difference method , indicate that correlation between assay value and sample interval length ( each sample interval length represents an individual bed or stratum of the formation ) , apparently has little effect on the independence between successive assays , between successive sample interval lengths , and between the products of assays and sample interval lengths . Therefore , these data can be analyzed statistically as long as the original sample sections have been selected at random for sampling .

Jan 1, 1964

By J. R. Long

The investigations described herein are concerned with a portion of a systematic research, by the Federal Bureau of Mines on ductile titanium. The Bureau's work on the metal has resulted in development of a semi commercial process for the preparation of titanium and has also made available significant information on the fabrication and physical properties of this new strong, light, corrosion-resistant metal. Considerable interest has been aroused by this work, and a number of other laboratories have begun similar investigations. However, the necessity for Consolidating titanium by normal powder metallurgy methods presents difficulties in producing commercial forms and shapes on a large scale. This investigation was therefore undertaken for the purpose of improving the technique for consolidation of titanium powder into solid nonporous metal.

Jan 1, 1949

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By Q. H. Forbes

"The high injury rand fatality rate in coal mining, as compared with other industries, has caused the mining industry to become more and more interested in accident prevention methods.The prevention of accidents in the mining industry is probably not as simple a problem as it is in other industries, but if the experience of coal mining companies who have taken up the work of accident prevention seriously during recent years means anything, there is little doubt that most mining companies car improve their accident records very materially.Such results can be obtained in practically all instances without adding to production costs. In fact, there is little doubt that a well-organized program of accident prevention Will bring about a 'material production cost reduction due to increased efficiency, lower labor turnover, fewer delays due to accidents, better satisfied workmen, and a direct saving in compensation costs as well as many other items of expense.The more closely a. person is connected with the work of accident prevention, the more he becomes a believer in the value of amity in human relationships and the more he is able to exercise a spirit of toleration, fairness, justness, and helpfulness toward the problems of others, whatever those problems may be. Human nature responds to just these expressions of good willAnother great and invaluable effect of working for safety, is the fact that it is building up in the mind an appreciation of that which is constructive and, conversely, in opposition to that which is destructive In other words; the person who is sincerely striving to prevent accidents because they are destructive, costly, tad injurious, is subconsciously training his mind to look on any proposition from a constructive point of view. Working for accident prevention and safety is about the finest social training any person can have. It does not make a Person a financial Wizard or an executive genius, but it does make for the highest type of citizenship.While humanitarian reasons alone should be sufficient to maze accident prevention work an important factor in every mining organization, there are other reasons as well, since it has been proved conclusively that there can be no efficiency and economy without safety, as somebody pays when safety is lacking. Every safety device pays dividends; every safety application evaded is an assessment and a loss. Dangerous conditions are the most expensive and extravagant conditions in or about a coal mine. The economic gains are of considerable interest to all coal mining companies and this is brought about as before stated--through decreased compensation rates, the reduction of labor turnover, etc."

Dec 1, 1930

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By F. G. Miller

[Petroleum technoloF;istz and 1 rot-re s s ive OT e:?ztors. con stantl;, are striving to increase the percentage of oil that y to recovered from reservoir rocks throe::;:: wells. The exhaustive studies that have been made of the function of natural r:; as in t h-_ T r odI action of oil, for cx<n.mTnle, have aidedd of.erators greatly in incroasin,&apos; the q-:Arrntity of oil recovered from reservoirs. i.rtural gas dissolv3d in ar--d otinerwwisa &apos;1s&apos;.,ocintjd under rre3suro with oil in roscrvoir roci.s, howover, i:; not the only source of energy available for moving oil through sa&apos;:&apos;l to wells. l becoming "reservoir-energy conscious&apos;t engineers hr-vo -d o^.rued t}:-Lt in many petroleum reservoirs the edgewater flanking t -,e oil accum.-,lation conetitutos a potential source of onergy capable, tL-ou;_h rro? gr control, oil&apos; increasing oil-recovery efficiencies materially. i o ]enter is ti-.-,, on-cronchinunt of water into the oil- and gas--fillod ?art of the reservoir considered as an evil to be combatted by devious mot&apos;:r:ci :i,.t r,ttL er a natural conseque::c4, incident to the withdrawal of oil nna gas from the wells, that nay be T.usod advantrt eou ;ly in lonr`t}toning tr e r&apos;lowin g lift of wells a.nd, i norcas in:; the economic recovery of oil and Little is known about the by which water off: oratos in driving nil throe:gh reservoir roc:-.:,, nd i:. a scorcity of rubli:;Lad informs-¬t .on nn rates of :)Ov.:m.,:- t of : r.tcr ..at v:1:11 res,-_lt in ^r i-nu oil recoveries. Bureau of :fines engine_:? ; - reciate. the r,aucity of scientific knowledge or. the &apos;test methods of a,r.lying the natural water arive to in¬crease oil-recovery efficiencies ant ,i.;?l __-itir?,~ ting irties that will, they hope, Contribute to t.1&apos;.e T ros?Jr.t. small _ %nd of information now av tilable on tt:e cubjoct. This r».crt a oyno-.::is or brief comrilnt.ion of r,ublished data and thought accuinulnt.~d so far, to la)or;~.tory ox-:erimnntrr¬tiorn and, further rosoarch on the z_rrinciplos unri;rlyir..g the natr.rr+1 eater drive no it nffocts oil recovery. :Lie writer:: Lore that t.i.c cx-nositiorn of a?rzilable inforr-at ion i rcs?r.toi in the rernrt r .-II .i ,.1rtt cor_jt_-i:ctive tho.-_.I_t and efforts loadir,-z to -:ard more con.r .ote extraction n;&apos; o tl from reservoirs.]

Jan 1, 1938

By G. R. Hopkins, E. W. COCHRANE

According to reports received by the United States Bureau of Mines , Department of Commerce , as of January 1 , 1930 , there were 412 completed refineries in the United States with a daily crude oil capacity of 3,755,585 barrels . This compares with 413 refineries of 3,509,540 barrels capacity on January 1 , 1929 , which indicates that whereas the number of refineries was practically unchanged , the total capacity increased 8 per cent during the past year . Of the completed plants as of January 1 , 1930 , 358 plants , of 3,634,825 barrels total capacity , were operating and 54 , with a capacity of 130,760 barrels , were shut down . Compared with a year ago , this indicates a decline in the percentage of the total refinery capacity that is inoperative . There has been a decided decrease in the number of shut-down plants since 1924 and 1925 , when one plant in every three was inoperative . Many of the inoperative plants of 1924 and 1925 were constructed soon after the boom times of 1920. Some of these were operated for a time but were unable to show a profit during 1923 and 1924 , when an overproduction of crude petroleum was accompanied by demoralized markets for refined products . Prices for refined products improved in 1925 and 1926 , but only a comparatively few of the shut -down plants , then partly obsolete , were able to obtain or renew their crude connections and compete successfully with the larger , more firmly established refineries . After five years or more of continuous idleness , a refinery would be rendered practically useless through corrosion and obsolescence . Consequently , most plants now being carried as " shut -down " have operated intermittently since 1923 . struction . A material change occurred in 1929 in the matter of plants under con- On January 1 , 1929 , there were 14 plants under construction , with a potential capacity of 99,000 barrels per day , whereas on January 1 , 1930 , there were only eight plants of 37,200 barrels capacity being built . This decline was due to the fact that the construction program in west Texas , which was at or near its height on January 1 , 1929 , was completed prior to January 1 , 1930 .

Apr 1, 1930

By John R. Bradley

The available supply of fuel and power is a subject of importance at all times and particularly at this time. The following brief survey of fuel and power in the United States appraises the extent of the several primary sources of energy the approximate monthly demand, 1929-40; the chief centers of production and consumption; and shifts in the principal uses from 1929 to recent years. The period covers the boom year 1929, the years of the great depression, the more normal year 1937, the recession in 1938, the year 1939, and 1940 (which was affected by armament programs). In some instances, the data for 1939 and 1940 are preliminary. The four primary sources of fuel and power are coal, petroleum, natural gas, and water power. Wood fuel, important in some regions, and foreign trade in natural gas and hydroelectricity represent a relatively small part of the energy supply and are not considered in this study. The tonnages shown are in terms of coal, based upon the calorific or B. t. u. equivalents of the several sources of power. In practice, the usable heat or energy varies according to the type of equipment available for its use. For example, the efficiency of turbine water wheels and internal-combustion engines is much higher than that of steam plants and household-heating devices.

Jan 1, 1941

By Robert W. Geehan

The Bureau of Mines has been developing deposits of critical and essential minerals in the United States since 1939. A preliminary examination of the Union lead mine was made in November 1944 and January 1945 by W. T. Benson, a Bureau of Mines engineer, who recommended development by diamond drilling. The Bureau conducted a drilling project at the mine from February 12 to May 16, 1947. The property is in sec.12, T. 17&apos;N., R. 19 E., Mount Diablo Base and Meridian, in. southern Washoe County, Nev., about 15 miles south of Reno. The Union lead mane, also known 4s the Commonwealth mine, has been an intermittent producer of zinc-lead-silver ore since 1860. During World War II, ore was shipped to smelter& near: salt Lake City, Utah. The Bureau drilled 21 diamond-drill holes having a total length of 1,549 feet and 20 long percussion-drill holes with a total length of 359 feet. The program was designed to test for horizontal and vertical extensions of the ore body and to prospect for parallel ore bodies. As a result of this program, extensions of the ore zone were established, but no parallel ore-bearing structures were found. The areas drilled were limited by drill sites available.

Jan 1, 1950

By W. Beckering

IN CHARACTERIZING tars obtained by the low-temperature carbonization or North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite early it became evident in the tar-research program of the Bureau of Mines, U.S. Department of the Interior, that the small number of published spectra available for hydroxy aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was initiated as a continuing part of the tar program. As these spectra should be valuable to other investigators in this and related fields, they are being presented in this report. This group or spectra (figs. 1-98) represent 97 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Samples have been obtained from commercial and private laboratories or synthesized at the Bureau of Mines Lignite Experiment Station, Grand Forks, N. Dak.

Jan 1, 1959

This manual covers the operation and lubrication procedures for the Eimco Pumpable Roof Bolting Machine. This machine meets U. S. Bureau of Mines Schedule 2G Approval. This manual is divided into three major parts: 1. Machine dimensions; 2. operating instructions and; 3. Lubrication. Whenever front or rear, right or left arc mentioned it is assumed that the reader is standing behind the machine looking toward the boom. The boom is at the front of the machine. Safety When leaving machine parked on an incline turn wheels into the rib or block wheels. Do not run over power cables. Make sure your power cable is up out of the way so others can&apos;t run over it. Machine has a fire suppressor system for the power unit. The remote actuator (pressure cylinder) is located at the operator&apos;s station. Components and service procedures on page 59.

Jan 1, 1976

By Don B. Hunter

The Bureau of Mines investigated the extraction of alumina from calcined kaolin by leaching with boiling RCI in a train of three 50-gal continuous, stirred reactors. Slurry discharged from the reactors con-tained an excessive amount of fines, which impeded solid-liquid separation. Autogenous grinding of coarse solids that accumulated in the reactors was the source of the fines. This report describes modifications to the reactors and to the operations that led to decreased fines generation and improved solid-liquid separation. Modifications to the reactors included custom-made impellers, the addition of a baffle system, a subsurface slurry discharge system, and slower rotation of the impellers. Concurrent testing of a continuous horizontal belt filter showed that the form filtration rates were increased from 350 to almost 1,000 Ib/h+ ft-2 when the modified reactors were used.

Jan 1, 1984

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By Frank D. Lamb

"INTRODUCTION The use of beryllium and its alloys has come into prominence in the last 15 years and increased considerably during the war. In contrast to other light metals, such as aluminum and magnesium, beryllium is relatively hard, has a high melting point (1,285° C.), and other properties that make it resemble steel in many respects. It has a specific gravity of 1.85, is only slightly heavier than magnesium (specific gravity 1.74), and is appreciably lighter than aluminum (specific gravity 2.7). Its lack of ductility prevents its use as a structural material, but this difficulty may be overcome in the future by the use of various alloy forms. The only important commercial alloy in which beryllium is used today is with copper. The addition of small percentages (1/2 to 2 percent) of beryllium to copper imparts properties to the alloy that make it desirable for use in springs carrying electrical current, particularly at high temperature. Many other uses of berylliam are known, and new uses are being found constantly that make the metal of increasing interest.Possibly the main factor preventing the use of more beryllium is the lack of a large source of beryllium ore. Many beryllium minerals are found as minor constituents of natural deposits, some of the more common ones being beryl (Be3Al2(Si03)6), chrysoheryl (Be A1204), helvite (3(Mn, Fe) Be Si04. MnS), and phenacite (Be2Si04). Of the known beryllium minerals, beryl is by far the most common and has been found distributed rather widely throughout the world. It usually occurs associated with granitic rocks and is commonly found as a constituent of granitic pegmatite."

Mar 1, 1947