Search Documents

By Ehsan Nasiri, Keivan Pak Iman

Historically, boulders are a frequent source of problem in soft ground tunneling. It is important to attempt to make an assessment of the nature and quantity of the boulders, although in many cases, it will be impossible to do so with great accuracy. Boulders, can pose major problems for TBMs in terms of slowing down or halting the tunnel advance, cutter damage, and abrasive wear. Although proper selection of the TBM and the cutterhead can reduce the risks, ground uncertainties still cannot be eliminated. The paper reviews a case study of a 3480 mm diameter EPB-TBM in Toronto utilized for completion of 2.5 km tunnel in Glacial Till, crossing the CP railway, HWY 401, a creek, and a confined aquifer. Alignment consists of multiple horizontal curves including small radius curves (r=210 m) at shafts breakthrough. An unexpected boulder cluster lead the contractor to experience extreme damages to the screw conveyor, RFJ system and causing a crack in main motor plate which resulted in losing one of the six main motors. This paper reviews contractor’s solutions and includes discussion on specific claim resolution method used in this project that can be of great value in preparation of specification and GBR for similar projects.

Jun 13, 2021

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By Heinz Petry

In deep strip mines the job of moving overburden may be so much bigger, and more costly than the removal of coal or ore that the operation is often called dirt mining. Constant improvement in stripping machines and techniques of using them is needed to offset rising costs and to increase production in mines that are now operating, and to make it economically possible to work deeper or thinner deposits.

Jan 1, 1962

By Girish Roy, Robert Goodfellow, Angel Del Amo, Bingzhi Yang

Designing and constructing tunnels in seismic prone areas present unique challenges to both designers and contractors. The Westside Purple Line Extension Project– Section 3 in Los Angeles requires crossing an active fault that may subject the tunnels to extreme structural demands. In order to ensure that the linings will safely accommodate the fault movement, a revolutionary composite section—steel plate embedded in the intrados of the precast concrete segmental tunnel lining was finally selected. Additionally, continuous expansion steel plates over the circumferential joints will be installed to mitigate the potential opening of the circumferential joints.

Jun 13, 2021

By Yuting Xue, Taghi Sherizadeh, Mark Van Dyke, Dogukan Guner, Khaled Mohamed

The Coal Pillar Rib Rating (CPRR) technique has been developed to assist in rib support design in underground coal mines. One major challenge of the data collection process is the measurement of coal strengths in the field. Schmidt hammer has been verified as a useful tool to determine coal strength. An alternative approach is to obtain the representative strength of coal mass by determining the coal lithotypes in the field based on the coal brightness profile by experienced geologists or mining engineers. In this paper, image processing techniques have been used to quantify the texture of coal images of different lithotypes with the purpose of classifying coal lithotypes. The coal images were collected from the pillar ribs with exposed surfaces in underground coal mines, and the coal lithotypes were identified when taking the images. The method of Gray-Level Co-Occurrence Matrix (GLCM) was used to analyze the textures of coal images of different lithotypes, and the texture parameters, such as contrast, homogeneity, energy, and entropy, were compared. The results show that the images of coal with different lithotypes have different textures, which can be quantified through the image processing. The results from this study demonstrate the potential of classifying coal lithotypes using rib photos and easing the data collection process of CPRR.

Feb 1, 2024

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By R. L. Wiegel

Some of the mineral deposits that are being processed today, and especially those expected to be processed in the future, have relatively low compositions of the valuable mineral. With these low-grade ores, it is necessary to be able to design processes that are sufficiently low-cost to permit exploitation. One approach to minimizing the capital and operating costs for these processes is to use the capabilities of computer process simulation in the design phase of development, to make important technical and economic decisions regarding the evaluation of alternative process flow schemes, the selection of equipment and the choice of operating conditions. There are mathematical simulation models for most mineral processing operations, including several each for size reduction, size classification and mineral separations. To be able to tie these individual operating models together in an integrated mineral process simulation, however, it is important, in fact in some cases essential, that there be a model which describes how the mineral system responds to size reduction in making the liberated valuable and waste mineral particles available for concentration or rejection operations and the locked particles available for possible recirculation. This, then, is the role played by the mineral liberation model, showing the relationship between particle size, quantity and composition throughout the process.

Jan 1, 2011

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By g. Caproni

The main constituent of the feed to the "Sulphide Section" (31 t/h), in the F. Sartori Plant (6000 tid) of the Miniere di Mon)eponi(Sardinia), is the ore of the Campo Pisano -Funtanaperda Mine (1 ? Difficulties have always been experienced in the treatment of this ore, owing to the extramely fine Pyrite-Sphalerite intergrowth and to the high Pyrite and soluble salts contents. The first mentioned difficulty was overcome with a rather complex flowsheet (see fig.1A and lB)(2); the others with a reagent combination that required a pH of 11 in a pulp loaded with soluble salts. This meant high consumption of alkalizer, and also of the other reagents; furthermore the alkalizer had to be mainly NaOH with only minor amounts of lime, because the latter tended to depress not only the pyrite but also the middlings, which were supposed to float. With dialchylditiophosphate alone as a collector, a lower pH could have been used, but a certain amount of amylxanthate was indispensable to promote flotation of the middlings. On the other hand, a bulk-flotation of sphalerite and pyrite at low pH could not be very advantageous on account of the high pyrite content in the feed(3).

Jan 1, 1971

By Ramiro da Conceição do Nascimento, Horst Guenter Feldhagen, Rafael Piumatti de Oliveira

Mixed hydroxide precipitate (MHP) is a nickel intermediate product that has economical benefits to downstream leaching of lateritic marginal ores. Usually, this product is subsequently processed and refined to produce nickel by hydrometallurgy, but an alternative route can be made integrating hydrometallurgy and pyrometallurgy. Assessing the overall consumption of ferroalloys to obtain stainless steel, as an increasing practice performed in China, the synergy of nickel extraction from laterites by leaching and precipitation asMHP with the production ofMHP agglomerates applied as rawmaterial to furnaces of ferronickel production is a very attractive practice. This work aims to further the technological development of an agglomerated product feasible to hydro-pyro integration. The agglomeration experiments were performed by traditional pelletizing (firing the pellets) and cold bonded pelletizing (aging the pellets by appropriate stocking). Appropriate compositionswere prepared withMHP, additives and binders for each of these routes. A specific study of binder composition was made to find an adequate melting point. The produced pellets were tested to prove their properties by crushing strength tests. The standardization applied to iron ore was followed. The best result of crushing strength was 98.52 daN/pellet. The agglomerates with approved crushing strength for use in electric furnaces were smelted to produce alloys containing nickel; the agglomerates were characterized by scanning electron microscopy. The alloy obtained was metallic ferronickel with sulphide precipitates. Therefore, MHP pellets can be precursors of nickel alloys, which have to be refined to obtain the desirable composition.

Jul 6, 2020

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By Neal Retzer, Adam Bedell, Nick Cioffredi

The first wagon trail across Loveland Pass was built in 1869 thus starting the struggle between the Colorado Rockies and interstate travel. The 1st Pioneer Bore underneath Loveland Pass at the Continental Divide in Colorado was attempted between 1941 and 1943 and was abandoned due to ground conditions at the Loveland Fault. Construction on the nearby Eisenhower Tunnel began in 1967 and was completed in 1973. Numerous challenges associated with tunneling, including at 11,000 ft were overcome. The purpose of this paper is to summarize the history of investigation and construction challenges associated with the Eisenhower Tunnel to celebrate its 50th anniversary.

Jun 13, 2023

By Hoke M. Garrett

The domestic cement industry demands about 550 trillion Btu annually, at a time when reduced fuel use has become a necessity due to the energy shortage. In terms of the overall power picture, that 550 trillion Btu, which includes both fossil and electrical energy, means about 0. 870 of all energy consumed in the U. S. The various factors influencing reduction of this energy consumption are the subject of this paper. Nationally, the energy shortage is being tackled on two fronts--increasing supply and reducing demand. Making cement consumes energy; therefore, the industry cannot join the effort to increase the energy supply except indirectly as noted later. Demand can also be attacked on two fronts--by reducing cement consumption or by reducing the amount of energy required to make cement. The following discussions on reducing cement industry energy consumption center briefly on the prospect of reducing cement consumption followed by a broad evaluation of the potentials for improving cement-making thermal efficiency.

Jan 1, 1974

By F. Ikumapayi

Hydrogen peroxide production was measured during the grinding of a complex sulfide ore, and its oxidizing effect on solid surfaces was investigated using Fourier transform infrared spectroscopy (FTIR) with diffuse reflectance attachment measurement. In turn, an attempt was made to correlate the formation of hydrogen peroxide, surface oxidation and sphalerite flotation. Additionally, in order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the effects of major components of calcium and sulfate species present in recycled process water and the effect of temperature on sphalerite flotation were investigated through bench-scale flotation tests using complex sulfide ores. The significance of process water species in flotation was studied using tap water, process water and simulated water containing calcium and sulfate ions. Formation of hydrogen peroxide was revealed during the grinding of the complex sulfide ore, and its formation was counteracted by diethylenetriamine (DETA). The FTIR spectrum of the pulp solid fraction showed varying degrees of oxidized surface species, which are related to the concentration of H2O2 analyzed in pulp liquid. Bench-scale flotation using two different complex sulfide ores showed that sphalerite recovery is better in process water than in tap water. Flotation results also indicated a varied recovery of sphalerite at different temperatures in either tap water or process water.

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By Neilson Rudd

Many deep well waste disposal. operations have adopted the technology of the petroleum industry but fail to make full use of the knowledge and experience upon which this technology is based. Inexperience in subsurface exploration commonly leads industrial personnel to an over simplified understanding of the complex subsurface rock/fluid environment and overly optimistic "degree of exploration /adequacy of knowledge" ratios. Several fundamental differences between disposal and petroleum production are discussed. In particular, the evolution of understanding of the subsurface in relation to degree of exploration is demonstrated by summarized case histories of such other forms of subsurface fluid exploitation as oil pro¬duction and underground gas storage, tracing subsurface interpretations from the initial exploratory concept to that of fullest development. Evolutionary changes in interpretation and their significance as applied to deep well disposal are stressed.

Jan 1, 1971