Search Documents

By Wen L. Cai

This paper examines the effects of different block dimensions and cone bases on the economic open pit limit design based on case studies on a coal deposit consisted of two west- east elongated, near vertical thin seams starting with a base model dimension of 200x170x50 (NX*NY*NZ) with a block dimension of 10mx5mx4m (DX*DY*DZ), the blocks were combined along easting, northing and elevation directions. Two cone bases were used, one with a base radius of 10 meters, the other with a base radius of 0. Two pit design algorithms, one is the floating cone algorithm, the other is an optimum algorithm, were used to see which one of the two pit design algorithms is more sensitive to block dimension and cone base variations. The results are presented and analyzed.

Jan 1, 1992

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995

By Z. F. Wang, W. K. Choi, A. E. Torma

The present study has investigated the bioleachability of low-grade and high-grade pyritic gold ores and the extraction of gold from the leach residues of bioleaching with thiourea solutions. Final gold extractions as high as 96% were obtained from the high-grade ore and above 93% from the low-grade ore. The gold extraction was found to follow the extent of pyrite biooxidation. Using a cyclic voltammetric technique and carbon-paste-FeS2 electrode it was found that the semiconductor pyrite oxidation involves many intermediate electrochemical reactions. Furthermore, the oxidation is solid-state diffusion controlled as suggested by chronoamperometric and chronopotentiometric measurements.Using Sand's approach, the activation energy of solid-state diffusion biooxidation of pyrite was determined to be AEa=22.4 kJ. A generalized model for the mechanisms of pyrite oxidation has been presented.

Jan 1, 1990

By R. J. Hickson

From 1993 through 1999, Cyprus Amax Minerals successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized and an environmental issue was appropriately remediated. The projects stretched over three continents: from arctic Russia to the Atacama Desert, from sea level to an elevation of 4,900 m (16,00Oft), from city suburbs to remote wilderness and from a low of US$130 million to more than US$ 1billion. The operations included open-pit and underground mines, mill and leach facilities and involved gold, copper, molybdenum and coal. The diversity of these projects inspired Cyprus Amax to create a "best-practices” project-management protocol to steer corporate expansion in the new millennium. This paper summarizes these best practices, while highlighting the project-management pirfalls to avoid.

Jan 1, 2000

By Diane Germain, Normand Tassé, Claude Dufour

At the East Sullivan site, pore-waters underlying a wood waste cover that prevents sulfide oxidation are characterized by an anoxic environment, abundance of dissolved organic substrates, and near neutral pHs. Such conditions favor sulfate reduction and base metals precipitation as sulfides, as well as carbonate-metal precipitation. Pore-water composition from 1992 to 1998 shows a significant Fe2+ decrease. Therefore, the restoration strategy of that site capitalizes on these alkaline and reductive properties. Since 1998, a novel treatment of acid effluents, based on the recirculation of water discharged around the impoundment through the organic cover, is tested on the site. Available data gathered in 1998 and 1999 shows that the pH of recirculated water flowing within the wood waste cover increases by 2 to 4 units and that Fe,, concentrations decrease by a factor greater than 6.

Jan 1, 2000

By Shosei Serata

Salt cavities have been proven to be a suitable structure for underground storage of various matters in gas, liquid or solid form. Since the technique of underground storage was developed mainly through field experiences in solution mining, a wider use of solution cavities for storage of gaseous and solid matters requires evaluation of three basic rock mechanics problems; cavity instability, boundary rock failure and surface subsidence. Cavity instability is due to the non-linear long-term creep properties of the surrounding ground media which are sensitive to cavity pressure changes associated with the storage. The cavity boundary rock failure is caused by the loss of effective confining pressure to the boundary rock media in the process of storage of gaseous and solid matters. Surface subsidence is the final outcome of the stress envelope originated around a cavity, eventually reaching the ground surface. The rock mechanics processes of instability, failure and surface subsidence are explained by using various field examples in salt domes and bedded formations. Methods of solving the problems are discussed including stress relief, stress control and computer optimization of design.

Jan 1, 1973

By George E. Aiken

Agglomeration developments in the iron ore industry of North America are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. These relationships have occurred mainly during the last 20 years. Many of these changes are an outgrowth of events which involved the history of the Mesabi Range. Although magnetic taconites had been discovered in the Lake Superior area about 1870, they remained unvrorked in part for lack of concentration methods and a generally unfavorable economic climate. Some 20 years later the rich Mesabi hematites were found beginning the era of direct shipping ores which continued through World War II. These Lake Superior iron ores included reserves of an estimated three billion tons. Following World War II, decreasing ore grades and rising costs began to force the closing of many underground iron mines. The early 50's saw the beginning of the decline in direct shipping ores and a spurt in produc- tion of natural iron concentrates. However, the market for unprocessed concentrates began to decline in the early 60's as agglomerated products and foreign ore s began to dominate the U. S. market.

Jan 1, 1973

By K. N. Santini

Natural zeolites are gaining recognition as an important commodity with an increasing number of industrial and consumer applications. This potential has prompted the Anaconda Minerals Company and other firms to investigate occurrences and markets for zeolites. The deposits of mordenite-rich tuff at Rome are of interest for their economic potential and for the excellent opportunity they provide to study a zeolite deposit formed in a hydrologically closed basin. Location The Rome property is located approximately 9 km west of Rome, Oregon, in Townships 31S. and 32S., Range 41E., Malheur County. It lies within the Owyhee Uplands of the northern Basin and Range physiographic province (Figure 1). The area discussed here includes a major portion of the depositional basin in which the zeolitic tuffs occur.

Jan 1, 1982

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By Arthur B. Arnold, Curtis T. Scott

The Blue Mountain Tunnel is a part of the Sultan River Hydroelectric Project. The Sultan Project is in the Cascade Mountain Range, approximately 56 km (35 mi) northeast of Seattle, Washington. The geology is structurally complex, consisting of graywacke and argillite, with lesser amounts of metaigneous rocks. The tunnel, excavated with a tunnel boring machine (TBM), is 4.32 m (14 it) in diameter and 6.3 km (3.9 mi) long. The average 24 hour advance was 41 m (134 it) with a maximum of 71 m (234 it). The tunnel is essentially unlined except for 383 m (1,257 it) in a low cover area and in the rocktrap. Inspection of the tunnel after one year of operation showed it to be in good condition with only a minor amount of rock debris in the rocktrap.

Jan 1, 1987

By David G. Abbott, Frank Coluccio

This paper will discuss the construction of nearly 165 m (540 ft) of 3.5. m (138 in) o.d. reinforced concrete pipe to replace an existing utilidor under the Duwamish River in Seattle, Wash. The project required that two 27.4 m (90 ft) deep shafts be installed for use as jacking and reception shafts during the tunneling operation, and permanent vaults once completed. Soil conditions to be excavated consisted of soft saturated sand and silt with a 21.3 m (70 ft) water head. This required the shafts to be constructed using ground freezing techniques and the tunnel installed by pipe jacking, using a Mechanical Earth Pressure Counter Balance (MEPCB) slurry shield. The original utilidor was constructed between 1924 and 1925, and has since been deliberately flooded because it is considered to be structurally unsound.

Jan 1, 1995

By D. S. Kostick

Soda ash production in the United States during 1994 increased 4%, reaching 9.3 Mt (10.2 million st). That was the second highest production year. Domestic nameplate soda ash capacity is about 11 Mt (12 million st). Overall, the industry operated at about 85% of capacity. Some companies produced at 100% of capacity while others produced at below their design ratings. Although domestic soda ash consumption was slow during the first half of the year, third- and fourth-quarter sales increased, especially in the flat¬glass and fiberglass sectors. These two sectors increased because of greater demand for glass products in the automotive and construction industries. Soda ash sold for pulp caustic soda increased during 1994. This was due to higher prices for and reduced availability of electrolytic caustic soda. It is often preferred for pulp digestion because of its stronger alkalinity.

Jan 1, 1995

By Shunji Sukizaki

Recently development of cheaper and cleaner energy sources has become a more important and urgent issue, because of the soaring crude oil price and environmental problems such as global warming. In this social context, to establish basic technologies and solve fundamental issues associated with environmental impact assessments, the Environmental Impact Assessment Group of the Research Consortium for Methane Hydrate Resources (MH21 research consortium) in Japan has conducted a number of research and development activities since FY2001. These activities include: 1) surveys of the marine environment that will form the basis of environmental impact assessments associated with methane hydrate development; 2) the development of core technologies to monitor deep-sea environments; 3) research of major issues related to environmental impact assessments; and 4) the development of numerical models to predict the deformation of seafloor sediments containing methane hydrates.

Jan 1, 2008

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By D. M. Cregger, J. L. Rosenblad, R. E. Ranken

The construction of a large span, high-walled underground opening in a low strength shale rock is unprecedented. The feasibility of constructing a pumped storage project with several tunnels and a large underground powerhouse in low strength shale rested largely on the feasibility of building stable openings large enough to accommodate the required equipment. Because of the lack of experience with large openings in shale, the decision was made to excavate a test adit and test chamber and conduct a multi-faceted geotechnical evaluation program designed to yield pertinent in-situ data on the ability of the shale to accommodate a large underground opening. Factors considered in the shape, size, orientation, and location of the test chamber were: (1) similarity to the anticipated powerhouse chamber, (2) nature of the most important data to be obtained, (3) feasibility of construction, and (4) economics.

Jan 1, 1983

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By M. F. Vancas

The San Manuel oxide ore reserve ranges in depth from being exposed on the surface to lying 1000 ft. beneath a conglomerate layer all of which is confined in the subsidence zone of an active sulfide block caving operation. Present day recovery of the oxide copper values is either by open pit mining-dump leaching, or in-situ leaching of the oxide ore using dilute sulfuric acid solutions and solvent extraction/electrowinning processing of the pregnant leach solutions. Future plans are for continuation of leaching with expansion of reserves and increased processing rates. The state of the mining industry and copper in particular has not been good for a number of years. All of the producers that are still operating have made major adjustments in order to remain competitive. Magma Copper Co. is no exception.

Jan 1, 1987

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

By Setareh Afrouz, Emily Sarver, Cigdem Keles

The resurgence of severe lung disease among US coal miners since the mid-1990s has led to efforts to better characterize and monitor respirable dust exposures, particularly focusing on mineral constituents from rock strata surrounding the coal. A rapid analysis method for silica (quartz) mass using direct-on-filter Fourier transform infrared (FTIR) spectroscopy has been developed, which can also estimate kaolinite, a primary silicate mineral in many coal mines.

Feb 24, 2022