Search Documents

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

By M. J. Beus

A shaft is truly the "lifelinen of an underground mine. Damage to the shaft lining and guides as a result of ground movement can result in serious loss of production and extensive and continual repair. In some mining districts, annual shaft repair and maintenance costs resulting from high rock stresses and excessive displacement are in the millions of dollars per year. For many years, the Bureau of Mines has conducted research to characterize the rock mass and to develop structural guidelines to improve the design of accessways in deep mines. Much of this work has centered on determining the in situ conditions that affect the structural stability of shafts in the Coeur d'Alene Mining District of northern Idaho. Recent work by Beus and Board (1984) has concentrated on measuring the rock and support behavior during sinking of the Silver Shaft at the Lucky Friday Mine. These results are currently being used as a comparative data base for further basic research as well as to establish structural design criteria. The factors affecting the deign and structural stability of deep mine shafts are numerous. A design approach that use field data as input and directly compares field measurements with numerical models can validate the procedure and provide realistic design criteria. Naturally occurring "fixed? conditions such as magnitude, direction, and ratio of in situ stresses, geologic environment, and physical properties and constitutive relationships of the rock mass ere obviously basic to numerical modeling.

Jan 1, 1989

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By Ray Brandon

The recent introduction of polymer geogrids for ground control purposes in underground mines allows mine operators more flexibility in choosing improved products for several applications. This is evidenced most clearly in longwall recovery operations. Since November, 1994, many mine operators have chosen Fortrac geogrid assemblies for the purpose of securing longwall recovery areas prior to shield removal. Fortrac is a lightweight, strong, and flexible polyester geogrid available in many strengths. Utilizing the "diamond" seaming method, different strengths of Fortrac geogrids are easily fastened together so stronger geogrids may be placed in the most critical areas and lighter geogrids in less critical areas.

Jan 1, 1996

By Shosei Serata

The Stress Control Method improves productivity and safety in underground coal mining. The method stabilizes the roofs and floors of mine openings in both shallow and deep coal beds, regardless of whether or not there are ground stability problems. This paper describes the means by which a tapered pillar experiment is used to collect in situ data, which is then used as input for a computer model. The resulting computer model is then used to optimize Stress Control design for the mine under study. The behavior of any underground coal mine is not elastic, as is generally conceived in the conventional view of rock mechanics, but rather is highly time-dependent and site-specific. Unfortunately, conventional rock mechanics methods based on the elastic principle are not able to capture the highly non-elastic nature of ground behavior which actually occurs. To capture actual behavior, a new method of study is required. In this regard, geomechanical study of an underground coal mine may be compared to studying the behavior of a living fish. Its true behavior zannot be understood by examining it "dead in the laboratory. It Is the "live" nature of the coal mine that is required for design optimization of the Stress Control Method in the given mine. The Stress Control Method is based on a time-dependent theory of the global behavior of the mine ground, which generally contradicts the conventional elastic theory of ground behavior. Therefore, site-specific adaptation of the Stress Control Method required a comprehensive understanding of the global behavior of the mine as a function of time and site-specific ground conditions.

Jan 1, 1986

By Gang Chen

Conventional methods designate a factor of safety, a deterministic number, to indicate the stability of a mine excavation. However, this deterministic description of excavation stability is frequently insufficient or inaccurate and, sometimes, misleading. Employing the probabilistic analysis to determine the likelihood of mine excavation failures will lead to a better understanding of ground control problems and result in more rigorous designs of the excavations. Based on the theory of probability, two approaches are taken in this study for the probabilistic analysis of excavation stability. The first one utilizes direct integrations for the estimation of failure probabilities of mine excavations. Due to the complexity of the integration, this approach can only be applied to solve relatively simple problems. In order to overcome the limitation of the direct integration method, the second approach employs the first-order second-moment approximation of the failure probabilities for more complex ground control problems. The probabilistic analysis offers a deeper insight into the uncertainty associated with the stability of mine excavations. The study indicates that the distributions of parameter values play a significant role in the mine excavation stability, which can not be disclosed by the conventional methods of stability analysis. Greater dispersiveness of the parameter values will lead to a different probability of failure, although the factor of safety estimated by conventional methods stays the same if the mean values of the parameters are constant. By taking consideration of the probabilistic distributions of the parameters, the probability model can provide more reliable designs of mine excavations.

Jan 1, 1996

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By Gary B. Petersen

The author has developed a seven-step process called the Applied Rock Mechanics (ARM) Protocol that the author has used to solve numerous roof stability problems in mines throughout North America since 1975. It is a practical evaluation process using trained observation, innovative data collection instrumentation, video borehole cameras, analytical processes, and controlled testing methods that have become highly effective in solving ground control problems in every type of underground mine. This paper will describe each of the steps of the protocol and how the rock mechanics engineer applies them to resolve a typical ground control problem.

Jan 1, 2012

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By Nicholas Chlumecky

One of the oldest mine supports in use today is timber cribbing. In many mining operations material, installation and maintenance costs for timber cribbings are substantial. Their performance characteristics also add to mining costs. During the 1970'6, the U.S. Bureau of Mines recognized many of the deficiencies of timber cribbing and very successfully initiated the development of steel-fiber- reinforced (SFR) concrete blocks. Since the early 1980's this SFR concrete cribbing has been manufactured as a high quality product which has found increasing acceptance by mine operators. The rapid acceptance of the SFR concrete block cribbing has proven that its use is eliminating many of the deficiencies of timber cribbing while providing superior load carrying capability. The use of SPR concrete blocks to build the cribbing is based on the same principle as wood. That is, stacking longitudinal, rectangular blocks in layers in a crisscross manner. The blocks are positioned at right angles to the blocks of the layer below. With this situation, the possibility of misalignment exists when the concrete blocks at the base are not placed exactly parallel or when the blocks of the base are subject to unequal settlement. Such misalignments creates localized, high stress areas which reduces the load capacity of the cribbing made from SFR concrete blocks. Recognizing the problem of misalignment, the Underground Supports Division of Commercial Shearing, Inc., conceived a circular, one-piece, steel-fiber-reinforced concrete cribbing which is being marketed under the name - Donut Cribbing. This concept eliminates the possibility of misalignment and provides 100% bearing between layers of stacked cribbing as well as other advantages. The purpose of this paper is to discuss the performance characteristics, installation speed and economical factors of each of the three cribbing types -- timber cribbing, SFR concrete block cribbing and SFR concrete Donut Cribbing.

Jan 1, 1986

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012

By Tony Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and Laurel Hill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereonet, and rose diagram projections so that the Loyalhanna's structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts. pillar sizes, etc., that lessen miner exposure to these hazards.

Jan 1, 2002

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By Ulrich Paschedag

The WESTFALIA group of companies developer and manufactures underground mining machinery for complete high-performance longwalls. WESTFALIA uses a state of the art electrohydraulic system as the most important component for the realisation of today's fully automated plow or shearer longwall. The shield control unit (SCU) allows maximum custom designed software flexiblity as well as maximum hardware reliability. The master control unit (MCU) monitors shield support data as well as the plow/shearer position. By using an industry standard PC in an explosion-proof box with an intransically safe keyboard nearly unlimited software capabilities can be obtained with inexpensive hardware. Among various other modes of operation this MCU allows the monitoring and recording of data which can be transmitted to a surface computer. Production and operational adjustments can be made by the mine management based on the MCU information. Statistical analysis of the distribution of roof pressure under various conditions is also possible. The WESTFALIA automation system PM-4 gives the operator maximum flexibility and helps the mine management to run their longwall more efficiently and safely.

Jan 1, 1994

By R. D. Yancich

A case study of longwall mining surface subsidence was performed at a mine in Southwestern Pennsylvania. The mine operated in the Pittsburgh coal seam which averaged 70-72 inches with 6-8 inches draw slate in the longwall location. The average overburden depth ranged from 625 8eet to 660 feet. Three adjacent longwall panels were studied and classified as Panel 1, Panel 2, and Panel 3. The following is information on each and can be seen on the General Mine Map (Fig. 1).

Jan 1, 1984

By John Smyth

Mining through in panel entries and the full face recovery method has been successfully practiced at U.S. Stwl, Mine 50. Suppat of the cut-through entries and recovery room is critical. Traditionally, concrete crib or fly ash cement backfill has been utilized. However, these traditional methods are not feasible at Mine 50 due to the difficulties of the plow face mining through these types of support. Recent development of new cable support systems provides an option for cut-through entry support. Mine 50 and Jennmar Corporation personnel have worked together to design and apply the cable systems in the cut-through entries and full face recovery room to eliminate standing support. To date, a number of full face recovery rooms and cut-through inpanel entries have been successfully mined. The results indicate that the cable systems combined with high capacity shields, have provided sufficient capacity to support the roof. Utilizing the Jennmar Finite Element Analysis (JFEA) computer program (Stankus and Guo, 1996), an analysis of the stress and roof deflection changes as the longwall gradually cut through was conducted. From the finite element analysis data, a supplemental support plan was designed. The history and experiences at Mine 50 are presented. Based on the case experiences and modifications made to the finite element analysis, an improved design criteria for future use has been formulated.

Jan 1, 1998