Search Documents

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By Paramguru R. K, Jena P. K

Increasing demand for copper, lead and zinc with continuous depletion of good grade ore reserves, warrants the need for utilization of lean and complex ores of these metals. There is worldwide effort to develop suitable processes for these purposes. The present paper deals with the chloride leaching of complex base metal sulphide concentrates of two Indian deposits. A two stage leaching process is suggested keeping selectivity of metal dissolution in view.In the first stage most of the lead and zinc are reacted with dilute FeCI3 (0.3M) solutions at a temperature ono°c where major portion of the lead remains in the residue and zinc reports in solution. After taking out lead chloride by brine leaching, the residue has been treated for copper dissolution. A concentrated FeCI3 leaching at boiling temperature as well as ambient aqueous chlorine leaching have been separately tried to dissolve out the copper from the residue. Based on the results obtained, a flowsheet for the proposed process is presented.

Jan 1, 1981

By Crazy Horse - The Journal of Explosives Engineering - Vol 20 No 1

The crew at Crazy Horse Memorial has produced a w o n d e rful new video called “The Fine Art of Mountain Carving.” The video closely examines for the first time, the extraordinary explosives engineering on the Crazy Horse mountain currently in pro g ress in the Black Hills of South Dakota. The 56-minute video takes the viewer up the mountain for a behind-the-scenes look at the drilling and blasting crew at work on the mountain. The video was written, edited and produced by Robb D e Wall and is available exclusively from the Crazy Horse Memorial in both DVD and VHS formats. For i n f o rmation, see www.crazyhorsememorial.org The following, is a brief summary of the 25 steps involved in carving the mountain. The video goes into extensive detail on each of the 25 steps. Both those in the explosives industry and those outside the industry will find the video intere s t i n g .

Jan 1, 2004

Mining at Waihi on the Martha Hill commenced in 1878 and between 1892 and 1953 produced 35 million ounces of bullion from some 13.5 million short tons of ore from 40 named quartz reefs. The general geology of the ore is recorded in detail with differing interpretations by Bell and Fraser (1912) and Morgan (1924). The reefs and stringers have formed by fissure filling and replacement in mainly quartz andesite dacite flows within the Waihi 'Graben'. The host rocks are extensively propylitised with intense alteration forming zones of kaolin adjacent to the main reefs.

Jan 1, 1979

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or book- keeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. T he emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1964

By G. J. S. Govett

World mineral production is dominated by six countries - the U.S., the U.S.S.R , Canada, South Africa, Australia and China - which also hold most of the reserves of the world?s minerals. For the developed and centrally planned countries, there is a strong positive correlation between the mineral production of a country and its land area: there is no correlation between mineral production and land area for the less developed countries. These facts imply that, after taking due account of geological controlling factors, a country may expect to produce minerals in approximate proportion to its land are a provided that political, economic, and historical factors are conducive to mineral exploration and mining. Contrary to popular political belief in many parts of the world, the developed countries are the major source of mineral imports for the industrialized countries. Moreover, exports of ores and minerals account for a relatively small par t of world trade, and are an important factor in the export picture of only a few of the less-developed countries. The looming resource confrontation between the developed and the less-developed countries is based largely on the false premise that the industrialized countries of the world are minerals-poor and owe their wealth to cheap minerals from the less-developed countries. The data presented refute this. Geological controls are relatively minor in the present distribution of world mineral production; political and economic factors are dominant. It is argued that an expansion of world trade in minerals - based on increased exploration and new forms of finance for mining ventures - rather than cartels, price-fixing and trade restrictions is by far the preferable solution to the problem of redressing the legitimate grievances of the poor countries of the world.

Jan 1, 1977

By H. Möhle

Premier Mine is a large underground diamond mine, situated at Cullinan in the Gauteng Province of South Africa. The mine hoists over 3 millions tons of diamond bearing kimberlite per year, from a modern, mechanized panel retreat block cave mining operation. Troughs sited at the base of the cave are developed into the overlying caved ore, allowing loading access to the ore through draw points. Trough opening is therefore a vital aspect of the mining operation. Most of the production is dependent on fast, reliable and safe trough opening. Successful trough openings are achieved under difficult mining conditions due to restricted void, long up-holes and the inherent properties of kimberlite?soft, elastic rock with a high swell factor. Early in 1998, Premier Mine undertook a joint development project (with an electronic initiation system supplier) to determine whether the use of a fully programmable electronic detonator system would enhance the mining cycle in the trough opening process. Blasting commenced in February 1998, initially with blasts of a similar size and duration to those that had been previously blasted with shock-tube systems, to confirm the operational capabilities of the blasting system. The accuracy, reliability and flexibility of the electronic delay detonators (EDDs) minimized associated risks for re-engineering of the trough opening process. Further, as blast timing was optimized, larger blasts were successfully initiated. To date over 20 troughs have been opened successfully with the use of EDDs. Not only did it take less time to open troughs, but also drilling and blasting operations have been optimized, as well as an overall improvement in safety. This paper details the benefits that EDDs have delivered to Premier Mine in this area. The logic followed is: ?Review of the original trough opening practices ?Re-engineering of the trough opening process ?Implementation of EDDs ?Evaluation of improvements and conclusions.

Jan 1, 2000

By J. van Lookeren

In the case of a reservoir where the oil underlies a large gas cap and overlies bottom water, production can be inzproved considerably if wells are perforated below the water-oil contact rather than opposite the oil-bearing section. The theoretical arguments for this improvement, which in some cases may be tenfold, are supported by experimental evidence. INTRODUCTION Reservoirs frequently consist of one sand body containing an oil layer underlying a thick, gas-bearing section and overlying bottom water (Fig. 1). Wells in such reservoirs are customarily opened up opposite the oil-bearing interval or, rather, opposite the lower part of this interval (Fig. 2). More often than not, it is inefficient or prohibited to blow off large quantities of gas with the oil. This im-psses a severe limitation on the drawdown, which results in low oil-production rates. Because of the small difference in specific gravity between oil and water, the latter will easily cone upwards, so that the production of water together with the oil is not prevented by this completion method. In such a situation wells should be opened deeper, in the originally water-bearing zone. The gas can be shut off by not perforating over the upper part of the interval (Fig. 3) or by a tubing hung close to the bottom of the interval (Fig. 4). Initially much water will be produced, but when steady-state conditions have been established (as depicted in Figs. 3 and 4) larger drawdowns are permissible than in a conventionally completed well, and correspondingly higher oil-production rates will result. Water cuts are only slightly higher because of the small effect of gravity on the water-oil flow distribution. CALCULATIONS The ratio of improvement has been estimated by means of approximate calculations. The completion depicted in Fig. 4 is the most convenient basis for these calculations. By postulating that vertical flow gradients can be disregarded, the Appendix shows that the well-known Dupuit formula can be obtained except for some complication due to the presence of two fluids rather than one. The Appendix makes the reasonable assumption that, for suitable boundary conditions, the oil layer occupies a constant fraction of the total fluid height throughout the reservoir. The oil- and water-production rates can thus be related to the liquid levels in the borehole as follows:

Jan 1, 1966

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

Good morning ladies and gentlemen, and may I thank you for inviting me once again to address your conference. I would first like to welcome you all, especially international delegates and conference speakers. ItÆs a pleasure to be with you all and I hope that you have the time to enjoy the many beautiful sights that the Coromandel and Bay of Plenty have to offer.   Holding your conference in Waihi is particularly apt, especially bearing in mind the conference theme û 'Mining in the Community'. There can be few venues in the world that can boast a world class gold deposit of the likes of Martha Hill located right here in the centre of a rural service town. ItÆs a deposit that has a mining history active now in its third century and that to date has yielded some 7.5 million ounces of gold and 50 million ounces of silver. I doubt that when John McCombie and Robert Lee discovered gold at Martha Hill in 1878 that they had any inkling that their endeavours would be the foundation for a mine that would become such an inseparable part of the economic and social fabric of Waihi for the next 130 years.   This is now my fifth appearance at a New Zealand minerals conference, I especially value such occasions as it allows me to comment on your industryÆs performance over the past year, share my thoughts on matters affecting your industry, and also to give you some feedback from central government.

Jan 1, 2006

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

The southern portion of the Swan Coastal Plain, a geomorphological element formed since late Tertiary times, contains commercially exploitable accumulations of ilmenite, zircon, rutile and monazite associated with a series of raised shorelines. The location of the deposits is controlled by a locally outcropping Archaen granite/ granulite complex and a sea current pattern determined by local geography and a prevailing wind direction. A progression from medium to high titanium ilmenite is evident parallelled by progressive leucoxenisation as the age of the deposits increases. Variations in trace element content accompany this process. Circulating groundwater has caused vertical mineralogical variations within individual deposits and by precipitation of iron has formed layers of hardpan.The Geographe Bay deposits are of important economic significance.INTRODUCTIONObservations made during the course of a brief survey of the southern portion of the Swan Coastal Plain provide an outline of the geology and mineralogy of the mineral sand deposits of the area. This preliminary study will require considerable modification in the light of more detailed work in the future.REGIONAL GEOLOGYThe Geographe Bay area is situated in the south-west corner of Western Australia between longitudes 115° O'W. and 116° O'W. and latitudes 33° 15'S. and 33° 45'S.The general geology of the area is shown in Fig. 1 where the control of the physiography exercised by the Cape Leeuwin-Cape Naturaliste basement ridge is readily apparent. Between this ridge and the Precambrian east of the Darling fault lies the southern part of the Perth basin which contains outcropping Jurassic to Recent sediments and lavas (McWhae, et al., 1958).The Leeuwin-Naturaliste ridge is the exposed portion of L Assistant Production Managcr. Laporte Titanium (Aust.) Ltd.

Jan 1, 1964

The paper point out the way whereby the Canadian gobernment regulates and motivates mineral development. In this sense, its important the role of Gobernment policy in the development of the industry to its a stage. The progress of industry is due to a favorauble political climate which created an atmosphere of trust that has atracted foreing investment. Therefore, Canada's position owes much to sound legislation that recognizes the high element of risk in exploration and development and also the exhaustibility of mineral deposits.

Nov 20, 1969

By Brent Duncan, Doug Harding, Bob Stier

The 73rd Street Tunnel Project is part of “The Tunnel and Reservoir Plan” (TARP)also known as the Deep Tunnel Project, and is located in the Village of Bedford Park, County of McCook, State of Illinois. The project consists of a ø 4.42 meter × 2,060 meter long (14´-6? bore, 6,760 foot)tunnel. The completed tunnel is used as a bypass tunnel for the McCook Cup Reservoir Project. The project was awarded to Affholder Inc. of St. Louis, in 2000. The paper describes the project in which a new, high-powered open gripper type main beam machine was used in which high advance rates have been achieved using conventional muck haulage techniques. Features of the project include the installation of rock support consisting of counter-sunk rock bolts that are required to be pull-tested for strength per project specifications. Installation and testing of the bolts are done during the boring cycle. Muck haulage was done by conventional muck car train and hoisting at the construction shaft. As the site layout did not include a tail tunnel, the trains needed to be shuttled at the shaft bottom. Even with the bolting requirements and the muck haulage without a tail tunnel, the Affholder site personnel still achieved high advance rates on the 73rd Street Project.

Jan 1, 2003

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

This publication is the fourth in a series of miners? circulars covering various phases of accident prevention in bituminous-coal mines; these circulars constitute a text hook for courses of instruction on accident prevention in bituminous-coal minim. To these may be added material of particular interest in the field where the course is presented. Other circulars in the series are: Accident Statistics as an Aid to Prevention of Accidents in Bituminous-Coal Mines (Miners? Circular 47). Accidents from Falls of Roof and Coal in Bituminous-Coal Mines (Miners' Circular 48). Accidents from Hoisting and Haulage in Bituminous-Coal Mines (Miners' Circular 49).

Jan 1, 1946

Andesites are a major source of aggregate for much of the North Island of New Zealand. There are regional differences with respect to some important properties of the andesites. Some are reactive with cement and are designated as potentially deleterious or deleterious by the concrete industry. Other andesites, particularly those that are slightly altered or weathered, have rather high Plasticity or Clay Indices and perform poorly in road construction.   The performance of the andesites has been investigated and can be shown to be determined by: +        the chemistry of the rock which in turn determines the chemistry of the glass in the rock; +        the presence of large amounts of groundmass glass in the rock; and +        the nature of the superimposed alteration processes. Environment of extrusion and how rapidly the rock has been cooled or chilled are also important as they determine the fabric of the rock and how much glass will be present in the rock.   There are three main types of alteration that affect the quality of the aggregate: 1.   hydrothermal alteration, 2.   late magmatic alteration associated with the devitrification of glass, and 3.   weathering.   Each of these alteration types produces different alteration minerals. In fresh andesites the devitrification of glass has an important affect on the rockÆs properties. The Taranaki andesites are shown to have unusually (in comparison with other North Island andesites) high Na2O contents, held in the groundmass glass, which is the fundamental reason for the high alkali û silica reactivity of these andesites.

Jan 1, 2005