Search Documents

By John G. H. Crump, E. W. Owen, Peter P. Gregory

A noticeable decrease in activity characterized the year 1938 in the West Texas area. The total number of wells completed dropped to 2045 for 19381 as compared with 2806 completions in 1937,l a decline of 27.12 per cent. This trend contrasts the sharp increase of 76.29 per cent in completions in 1937 over the 1936 total. Of 2045 well completions during 1938,' 1788 were oil wellsll 16 were gas producers1 and 241 were listed as failures.' During 1938 the ratio of dry holes drilled to oil-producing or gas-producing wells completed was one dry hole to each 7.48 oil wells, which compares with one dry hole drilled to each 7.477 oil wells in 1937. Nearly 200 wells drilled during 1938 in West Texas were either wildcat or partly wildcat wells, an increase of about 25 over the year 1937, when approximately 175 wells drilled were so classified. The 200 exploratory wells drilled represent about 10 per cent of the total number of wells completed. West Texas produced 71,257,541 bbl.1 of oil in 1938 as compared with 75,743,000 bb1.2 of oil in 1937, a decrease of 4,485,459 bbl., or a 5.92 per cent decline. By comparison, West Texas produced 22.36 per cent more oil in 1937 than during 1936. In December 1938, the 9247 producing oil wells in West Texas1 averaged 22.08 bbl. per day per well as compared with December 1937, when 7571 wells1 produced an average of 25.18 bbl. per day per well, or a decline in daily well average of 12.32 per cent. Discoveries No outstanding new fields were discovered in West Texas during 1938, in spite of continued, active wildcatting operations. Several new oil-producing areas were, found, however, the value of which is still unknown.

Jan 1, 1939

By E. W. Owen, John G. H. Crump, Peter P. Gregory

A noticeable decrease in activity characterized the year 1938 in the West Texas area. The total number of wells completed dropped to 2045 for 19381 as compared with 2806 completions in 1937,l a decline of 27.12 per cent. This trend contrasts the sharp increase of 76.29 per cent in completions in 1937 over the 1936 total. Of 2045 well completions during 1938,' 1788 were oil wellsll 16 were gas producers1 and 241 were listed as failures.' During 1938 the ratio of dry holes drilled to oil-producing or gas-producing wells completed was one dry hole to each 7.48 oil wells, which compares with one dry hole drilled to each 7.477 oil wells in 1937. Nearly 200 wells drilled during 1938 in West Texas were either wildcat or partly wildcat wells, an increase of about 25 over the year 1937, when approximately 175 wells drilled were so classified. The 200 exploratory wells drilled represent about 10 per cent of the total number of wells completed. West Texas produced 71,257,541 bbl.1 of oil in 1938 as compared with 75,743,000 bb1.2 of oil in 1937, a decrease of 4,485,459 bbl., or a 5.92 per cent decline. By comparison, West Texas produced 22.36 per cent more oil in 1937 than during 1936. In December 1938, the 9247 producing oil wells in West Texas1 averaged 22.08 bbl. per day per well as compared with December 1937, when 7571 wells1 produced an average of 25.18 bbl. per day per well, or a decline in daily well average of 12.32 per cent. Discoveries No outstanding new fields were discovered in West Texas during 1938, in spite of continued, active wildcatting operations. Several new oil-producing areas were, found, however, the value of which is still unknown.

Jan 1, 1939

By George C. Bravner

WITH the great expansion currently being made in the aluminum output of the United States, not only by the company that has heretofore been the sole producer but by a now organization in the field it is only natural to wonder to what degree the; ore reserves of the United States can contribute to the growing consumption. For the three-year period 1937-'39 the U.S. Bureau of Mine's figures indicate that the annual domestic production of bauxite averaged about 370,000 long tons, compared with average, annual import of about 194,000 long tons. About 85 per cent of the imports came from Surinam, nearly all of which went into aluminum manufacture. Not all of the or -kipped from mines in the United States is used to make alumimun however as Bureau figures indicate that in these three years an average of only 48 per cent of the domestic ore shipment were so used the abrasive chemical and other industries taking respectively 27, 21, and 4 per cent of the output. The recent increase in the demand for bauxite has been of course in it use for aluminum manufacture. This as is well known is largely attributable to the world race for supremacy in

Jan 1, 1941

By A. G. H. Anderson, Eric R. Jette

A few years ago, while the writers worked on the constitution of ternary and quaternary alloys consisting mainly of iron, chromium and siliconl,2 some information on microstructures and hardness, not incorporated in the published work, alas obtained. It has not been possible to do any further work on the properties of the alloys. The information possessed is hereby presented for the interest it may have in connection with the constitution of the alloys. Microstructures Referring to the iron-chromium-silicon diagram,' the regions that received most attention were those in which the sigma phase appears. It was found that the mode of occurrence of this phase varied much with the condition under which it mas formed, and the mode influenced considerably the hardness of the alloys. In some slowly cooled alloys, well within the alpha + sigma-phase boundary, sigma occurs in pabterns suggesting a eutectic. The structure of such an alloy is shorn in Fig. 1, showing it to be partly coarsely laminated and partly globular mottled. In other annealed and slowly cooled alloys, the lanlinated structure is entirely absent, and sigma appears in an irregular distribution of sharply cornered elongated areas (Figs. 2 and 3). These areas all possess a more or less mottled structure. A carbide phase is also visible in these two photomicrographs; it is represented by bright white arras of various shapes, sometimes apparently enveloping the sigma. Quenched and aged specimens, whose compositions arc: located near the phase boundary between alpha and sigma + alpha regions, have structures not unlike martensite (Figs. 5 and 6). Fig. 4 shows the structurc of alloy No. 35 as quenched from 1100" C.; it is a typical solid solu-

Jan 1, 1938

By Eric R. Jette, A. G. H. Anderson

A few years ago, while the writers worked on the constitution of ternary and quaternary alloys consisting mainly of iron, chromium and siliconl,2 some information on microstructures and hardness, not incorporated in the published work, alas obtained. It has not been possible to do any further work on the properties of the alloys. The information possessed is hereby presented for the interest it may have in connection with the constitution of the alloys. Microstructures Referring to the iron-chromium-silicon diagram,' the regions that received most attention were those in which the sigma phase appears. It was found that the mode of occurrence of this phase varied much with the condition under which it mas formed, and the mode influenced considerably the hardness of the alloys. In some slowly cooled alloys, well within the alpha + sigma-phase boundary, sigma occurs in pabterns suggesting a eutectic. The structure of such an alloy is shorn in Fig. 1, showing it to be partly coarsely laminated and partly globular mottled. In other annealed and slowly cooled alloys, the lanlinated structure is entirely absent, and sigma appears in an irregular distribution of sharply cornered elongated areas (Figs. 2 and 3). These areas all possess a more or less mottled structure. A carbide phase is also visible in these two photomicrographs; it is represented by bright white arras of various shapes, sometimes apparently enveloping the sigma. Quenched and aged specimens, whose compositions arc: located near the phase boundary between alpha and sigma + alpha regions, have structures not unlike martensite (Figs. 5 and 6). Fig. 4 shows the structurc of alloy No. 35 as quenched from 1100" C.; it is a typical solid solu-

Jan 1, 1938

By A. Rosenzweig, M. M. Karnowsky

The generalized binary diagram of the Au-Sn-Pb system is presented. The chief characteristic is the pseudobinary between lead and AuSn. On the high-gold side of the pseudobinary, four reaction isotherms were found at 363°, 274°, 225°, and 204°C. On the low-gold side of the pseudobinary, three reaction isotherms at 277°, 205°, and 176°C were found. A vertical section from the eutectic solder composition to gold was developed from the isothermal sections generated. METALLURGICAL problems arising from the intentional or accidental formation of Au-Sn-Pb alloys in soldering applications have indicated a need for information on the phase equilibria in this ternary system. The literature indicates that a complete diagram presenting this information has not been prepared. Even the recent excellent work by prince' entitled "The Au-Pb-Sn Ternary System" actually extends only to the AuSn or 50 at. pct Au range. There are more events in the 50 to 100 at. pct Au than in the less than 50 at. pct range. This article by Prince furnished much guidance in preparing this report. Initial efforts with the isopleth from the eutectic solder composition 61.9 wt pct Sn-38.1 wt pct Pb and 0 to 90 wt pct Au indicated that extensions of the work to the whole of the diagram (even if in less detail) were necessary to understand this system. In undertaking the construction of such a diagram, this study used differential thermal analyses (DTA) and metallography with verification and identification of phases by electron microprobe analyses. EXPERIMENTAL PROCEDURE The procedure began with the development of a cell which would be unreactive with lead, tin, and gold, retain its strength to 1100°C, exclude oxygen, and also furnish a suitable well for insertion and protection of a thermocouple to monitor temperature changes in the material. Such a cell would make it possible to reuse the sample should a repetition of determination be desired. Fig. 1 is a photograph of two such quartz cells as finally developed. The specimens have been run many times. The cell is made up of an inner sample bucket and an outer capsule with a thermocouple well which the sample surrounds. The DTA unit was an assembly devised from available instrumentation. The sample holder was a 3-in.-long cylinder of nickel, 2 1/2 in. in diam, fitted securely in a vertical tube furnace. Two holes 7/8 in. in diam were symmetrically located to receive the quartz cells. A dummy cell with nickel powder was used as the reference. The absolute temperature was recorded with a Pt/Pt 10-pct Rh thermocouple with an automatic Kaye ice bath compensator. (Calibration indicated the compensator to be accurate to better than ±0.5° over the 100° to 1000°C range.) The absolute temperature was measured in the sample and recorded on an L&N mul-tirange recorder with a full-scale display of 1 mv and automatic ranging of 99 mv. The differential signal between the sample temperature and the reference temperature was amplified with an L&N microvolt amplifier and recorded on an L&N Speedomax G recorder. Since two charts were obtained, the chart speeds were equalized and each event was noted on the differential chart, and the temperature at that time was obtained from the temperature record.

Jan 1, 1969

By Ralph D. Parker

The Frood mine (Fig. 1) is 2½ miles north of Sudbury, at a general elevation of 1000 ft. above sea level. It includes the original Frood location, which was the No. 3 mine of the Canadian Copper Co., and the adjoining Frood Extension, which until 1929 belonged to the Mond Nickel Co. Mine Openings The mine is operated from two vertical shafts and one underground incline shaft. No. 3, for men, supplies and ore, is a vertical six-compartment shaft in the footwall of the south mining area and extends froin surface to a depth of 3045 ft. No. 4 is a vertical three-compartment shaft, 2500 ft. north of No. 3 and adjacent to the north mining area. It extends from surface to a depth of 3345 ft., and is used exclusively for hoisting ore. No. 5 shaft, inclined at 65' to the horizontal and of three compartments, is near No. 4 and extends from the 2600-ft. level to 77 ft. below the 3100 level. It is used for development below the 2800 level. The ventilation shaft, No. 1, with which this paper is directly concerned, will be described fully in the following pages. Mining Methods The orcbody is laid out in 80-ft. sections at right angles to the gcneral strike and numerically indicated from the southern extremity toward the north. Each section consists of a 45-ft. stope and a 35-ft. pillar, extending the full width of the orebody. Pillars and stopes are superimposed from level to level. The present mining territory is divided into two vertical areas, a north and a south area. Both areas have the same number of stopes on each level, the two areas being separated by 10 sections to be mined later. In a few instances, at the ends of the south area, where the orebody has narrowed, longitudinal stopes are used, of more than the usual 45-ft. width. It will thus be seen that mining operations hare been concentrated in two relatively small areas, offering

Jan 1, 1934

By J. F. Radavich

Many heats of steel of low carbon value have been known to produce brittle pieces of steel. The brittleness is believed to be due to the impurities located within the grain boundaries. Such brittle steels have been examined with an optical microscope to ascertain the nature and the amount of the impurities present at the grain boundaries. Due to the relatively low resolving power of the optical microscope, the impurities are not visible in fine detail. The writer obtained some sheet steel and proceeded to determine the location of the impurities and to show the application of the electron microscope to the study of grain boundaries. One sample was known to be capable of becoming embrittled, whereas another sample was believed to be much less susceptible to embrittlement. Treatment of Specimens The specimens were embrittled by annealing above the A3 point under mildly oxidizing conditions. One piece of ingot iron could not withstand a 90" bend, whereas another piece of ingot iron was not affected and could withstand a 90" bend. The brittle piece was then annealed at a high temperature in a hydrogen atmosphere. The annealed ingot iron was termed cured and could withstand a 90" bend very easily. The three specimens examined will be designated as brittle, good. and cured in the discussion that follows. Procedure The sizes of the specimens were as follows: one piece of brittle ingot iron-3/8 by 35 in.; one piece of good ingot iron-96 by 1/8 in.; one piece of cured ingot iron-36 by 54 in. The specimens were too small to be polished by hand and therefore were mounted in bakelite. The polishing procedure was carried out in the conventional manner with the use of 1/0 through 3/0 papers, and the final polish was done with alumina on a billiard cloth. The specimens were then etched in a 4 pct solution of picral in alcohol, and then they were examined through an optical microscope. An area was chosen that showed distinct grain boundaries, and an effort was made to keep near this area when pulling the replicas REPLICA TECHNIQIJE The replica technique used in the preparation of the replicas for examination under the electron microscope is described in Electron Metallography.' It consists essentially of the following steps: 1. Obtaining a suitably etched specimen. 2. Applying a swab of ethylene di-chloride on the surface. 3. Applying a formvar solution on the surface. 4. Placing a screen on any desired spot. 5. Breathing on the fornivar layer. 6. Applying scotch tape on the screen and film. 7. Pulling the film and the screen up with the Scotch tape. 8. Separating the screen from the Scotch tape. This replica technique is very similar to the one described by Harker and Shaefer. However, with the added step, the percentage of replicas removed is very much higher regardless of the length of the time from the etching of the specimen to the actual pulling of the replica. The replicas were then shadow cast with manganese at a filament height to replica distance ratio of 1 1/2:7. This produced a very high contrast replica for use in the electron microscope. One of the dificulties encountered with this study was the restricted area of the specimen. The width of the specimens was the same as that of the 200 mesh nickel supporting screen. In order to increase the effective area, the screens were cut down as shown in Fig 1. The arrow indicates the direction in which the replica was pulled. This operation made it possible to obtain a large percentage of good replicas. Fig 3 shows an electron micrograph of a brittle piece of ingot iron and a grain boundary that was polished mechanically. The surface is very rough probably due to the incomplete removal of the flowed layer by the picral etchant. The grain boundary does show evidence of impurities. It was decided to electropolish the specimens to obtain a much smoother surface than the one obtained by mechanical polishing. ELECTROPOLISHING The specimens were cut in half to expose the metal on the back side. The exposed metal had sufficient area to make good electrical contact and electropolishing was carried out easily. The conditions for electropolishing were 0.9 amp, 35 volts, and 25 sec. in an electrolyte composed of 850 cc of ethyl alcohol, 100 cc distilled water, and 50 cc of perchloric acid. The polished specimens were then etched in the 4 pct picral solution for a shorter time than was necessary for

Jan 1, 1950

By G. L. Oldright, Virgil Miller

It is well known, in metallurgical circles, though less recognized in the technical press, that there have been remarkable increases in the capacity of the blast furnace in the last five .years. In places this capacity has been almost doubled. This paper will brief the experimental work carried on during more than five years with the direct assistance of the technical staffs of three lead smelters treating three distinctive types of feed. The first is the custom smelter of the International Smelting and Refining Co. at Tooele, Utah1, with a multiplicity of ores; the second, the Kellogg, Idaho, smelter of the Bunker Hill and Sullivan Mining and Concentrating CO.2, treating an exceedingly rich lead charge, such as is now being made more and more as the practice of concentration is improved; and the third, the smelter at Trail, B. C., owned by the Consolidated Mining and Smelting Company of Canada, Limited3, which treats highly zinciferous charges and later recovers zinc from the slag. In comparing operations at these three smelters it must be clearly recognized that the objectives in smelting differ through differences in economics. Many operations are not, then, strictly comparable. There have also been decided improvements in operation since all of the smelters were examined, though this was but a relatively short time ago. The general factors that govern speed in smelting and the loss of metals in the smelters examined will be stressed. (For details of operation the reader is referred to the original papers.) This paper will then be an examination of the fundamentals of operating units in a search for improvements, and not a description of three great lead smelters. Capacity of Blast Furnace Assuming a well prepared and self-fluxing charge to start with, enough coke must be added: (1) to melt the charge, particularly the slag-forming

Jan 1, 1937

By Herbert W. Graham

IRON ORE is widely distributed throughout the world. Ores sufficiently high in iron content to be practical for the operations of iron and steel making occur in so many places that it is only by the accident of political subdivisions that any given nation does not have adequate and suitable iron ore. Data prepared by various authorities show that in the Lake Superior region alone there are reserves of 1,200,000,000 tons of iron ore of an iron content and at the level of production cost to which the industry has been accus tomed. At an annual consumption of 80,000,000 tons these reserves will last fifteen years. Taken alone these figures would be alarming, but over a considerable period of years the total reserve tonnage has been more or less steadily increased by improvement and extension of mining and beneficiation methods. The rate of depletion of reserves has been only about one third of the rate of consumption. On this basis the cheap high-grade ores of Lake Superior would last 45 years.

Jan 1, 1947

By R. G. Ward

The temperature gradient in the subhearth metal or "salamandern of the iron bhst furnace results in the establishment of gradients in the concentrations of silicon, manganese, carbon, and sulfur. The temperature and compositional variations observed in three blast furnaces are analyzed according to irreversible thermodynamics and the systems appear to be close to the steady state condition. Apparent heats of transport, Q, for silicon, manganese, carbon, and sulfur are found to be respectively -17.5, -5, -2.1, and+22k cal per g mol. In conclusion the significance of thermal diffusion in extraction metallurgy is briefly discussed. INCREASING interest has been shown in recent years in the application of irreversible thermodynamics to metallurgical problems. In particular studies have been made of the transport of matter in thermal gradients1-' and under chemical gradients imposed by a binary solvent However, no detailed example in extraction metallurgy has been reported although gradients are the essence of many extractive processes. The case of the distribution of elements in molten blast furnace iron under a thermal gradient is discussed here. DATA In blast furnace operation the hearth bottom is often extensively destroyed by molten metal, and the metal may penetrate perhaps 10 ft into the furnace foundations forming a "bear" or "salamander". Several hundred tons of molten metal may thus exist beneath the level of the conventional tap hole and remain relatively undisturbed for several years under a thermal gradient. This system is subject to little convective stirring because the temperature decreases from top to bottom, and mechanical stirring due to movements in the stack and to tapping operations is unlikely to penetrate far into the metal. The system may thus be regarded as static

Jan 1, 1963

By P. J. Soltis

Direct as well as indirect evidence of a-phase ordering was found in a "near-a" type titanium alloy, Ti-8Al-1Mo-1V. The annealed alloy showed an anomalous decrease in second-stage creep rate at 950°F (510°C) and 47,500 psi. Anomalous increases were noted in initial yield stress after 500 hr creep exposure and in tensile strength after 1100 hr creep exposure. Debye-Scherrer X-ray diffraction patterns obtained on fine-grained polycrystalline speci-ment showed much line broadening and development of superlattice lines after 500 hr at 510° C. Examination with the light and electron microscopes failed to reveal phase changes in thermally exposed material, but detailed metallography is presented illustrating the plastic and fracture characteristics of the alloy. Electron-metallographic evidence is presented, however, which shows the nature of the nucleation and growth of ordered regions from the disordered a in annealed material. In the original phase diagram of the binary Ti-Al system constructed by Ogden et al.1 aluminum was shown to be soluble in a titanium over a wide temperature range at concentrations up to about 30 pct. Subsequently, a number of papers2-7 have appeared which indicate the existence of either intermetallic compounds and/or ordered phases in the a field up to 25 pct Al. In the most recent of these, Goldak and Gordon paw7 have determined unequivocally the ordered hexagonal D019 structure for Ti3Al in a 25 pct Al alloy. No superlattice lines were observed above 1112°F (600°C). Previously, the embrittle-ment encountered by Crossley and Carew4 in low- temperature heat treatments of binary Ti-Al alloys low in aluminum had been attributed to the appearance of a new phase in light micrographs. In the present work, direct as well as indirect evidence is presented showing the existence of a-phase ordering in what is essentially the binary Ti-8A1 alloy containing small percentages of the ß stabilizers molybdenum and vanadium, i.e., the "near-a" Ti-8Al-1Mo-1V alloy. Although Bohanek and Kessler8 have shown that this alloy has good stability at temperatures up to 1100°F (593°C), the present work shows instability at 950°F (510°C) where long exposure times were used. Light and electron microscopy proved very useful in revealing the mechanical behavior of ordered a and led to the conviction that ordered "near-a" alloys may have remarkably good properties and useful engineering applications.

Jan 1, 1965

By Dr. O’Neil Thomas J., Donald W. Gentry

Money is like an arm or leg-use it or lose it." -Henry Ford INTRODUCTION If it were not for the existence of interest, the analysis of investment opportunities would be greatly simplified. In the absence of interest, investors would be indifferent as to when cash outlays are made or cash benefits are received. It would, in fact, be irrelevant whether the outlays preceded or followed inflows as long as both amounts are known with certainty. Of course, it does make a considerable difference whether, for example, a firm receives $1 million now or five years from now. The reason is that money does, indeed, have a value which is a function of time. Interest is how this time value is measured. Interest is generally defined as money paid for the use of borrowed money. In other words, interest is the rental charge for using an asset over some specific time period. The rate of interest is the ratio of the interest chargeable at the end of a specific period of time to the money owed, or borrowed, at the beginning of that period. In order to understand why interest exists, it is necessary to take the lender's viewpoint. The lender can justify charging interest for several reasons: 1) Risk: The lender is faced with the possibility that the borrower will be unable to repay the loan. 2) Inflation: Money repaid in the future will be in units of lower value due to inflation. 3) Transactions Cost: There will be expense incurred in preparing the loan agreement, recording payments, collecting the loan, and other administrative tasks. 4) Opportunity Cost: By committing limited funds to one borrower, a lender is unable to take advantage of other available opportunities. 5) Postponement of Pleasure: By lending money, an individual (or organization) is postponing the pleasure which that money could purchase. Each of these is a valid reason for a lender demanding interest from a borrower. The level of interest is, like the price of other assets, determined by supply and demand. Nonetheless, from time to time various analysts have taken a then current average interest rate and broken it down into the components described previously.

Jan 1, 1984

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946

By G. S. Hume

RECENT developments in the Turner Valley gas and oil field, 40 mi. southwest of Calgary, Alberta, have indicated a large producing crude-oil area. Drilling be¬gan in Turner Valley in 1913 but no major developments took place until the fall of 1924, when Royalite No. 4 well at a depth of 3740 ft. in the upper part of the Paleozoic (Mississippian) limestone obtained a production - of 20,000 M cu. ft. of gas with a content of about one imperial gallon of naphtha (73° A.P.I.) per M cu. ft. This well produced as much as 600 bbl. of naphtha per day, and until abandonment in 1934 produced 911,313 bbl., which together with the gas sold was valued at about $5,000.000.

Jan 1, 1937

By R. I. Jaffee, R. M. Evans

IN recent years, the interest in liquid metals as heat-transfer media for power plants has been very great. The possibility of the development of nuclear power plants has increased this interest and served as the impetus behind much research on low melting metals and alloys for such purposes. The principal reasons for consideration of liquid metals as heat-transfer media lie in their high thermal conductivity and consequent high heat-transfer coefficients, stability at high temperatures, and the high ranges of temperature possible. The element gallium possesses some of the requisite properties for a heat-transfer liquid. It is a unique material, having a low melting point and a high boiling point. Pure gallium melts at 29.78oC, and suitable alloying will produce a metal which melts below room temperature. The boiling point is about 2000°C. As it is a liquid metal, the heat-transfer characteristics would be good. Gallium is not now readily available, due in part to a lack of uses for the metal. Nevertheless, it is not a rare element, and a sufficient supply of gallium exists to permit its consideration for this use. Since gallium has some promise as a heat-transfer liquid, owing to its unique properties, research on the subject was carried on at Battelle Memorial Institute at the request of the Bureau of Ships, U.S.N. The research had as its objectives the determination of the effect of alloying on the melting point of gallium, and the study of the corrosion of possible container materials. In this research, alloys were found which had significantly lower melting points than pure gallium, but none which simultaneously fulfilled other additional requirements, chiefly the corrosion problem. Neither was it found possible to reduce the melting point of certain otherwise suitable alloys appreciably by small additions of gallium or gallium alloys. The results gave little hope that gallium alloys can be developed which enhance the good properties and minimize the undesirable characteristics of elemental gallium. Thus, gallium now appears less promising than other metallic heat-transfer media. The experimental thermal-analysis techniques used in this work have been described.' Experimental Results As a first approximation, the development of low melting gallium alloys was based on alloying elements suitable for use in a nuclear power plant, which also lowered the melting point of gallium. Information from the literature, summarized in Table I, indicates that. tin, aluminum, and zinc are the only suitable elements which cause a lowering of the melting point of gallium. Indium and silver also lower the melting point of gallium, but are of little interest for use in nuclear power plants. Of the elements reported not to lower the melting point of gallium, there is some ambiguity on the behavior of copper. Weibke3 obtained solidus arrest temperatures of 29°C for Cu-Ga alloys from 60 to 90 pct Ga, 0.8C lower than the generally accepted melting point. This may be the effect of a eutectic close to gallium, or, more likely, the result of impurities, or experimental error. The seven elements listed in Table I whose effects were not known were of potential interest if they lowered the melting point of gallium. Their effects were determined experimentally for this reason. Binary alloys containing nominally 2 pct of each of these elements were prepared in the form of 2-g melts by placing the components in a graphite crucible and holding them in an argon atmosphere at 370°C for 5 hr. These melts were then subjected to thermal analysis. In all cases. the solidus temperature was the melting point of gallium. Since these elements (As, Ca, Ce, Mg. Sb, Si, and T1) did not lower the melting point of gallium, they were not considered further as components of a eutectic-type alloy. Ga-Sn-Zn Alloys Preliminary considerations of this system for low-melting alloys were encouraging. All three binary systems were of the simple eutectic type. The composition and melting points of the eutectics were as follows: Sn-9 pct Zn (199°C), Ga-8 pct Sn (20°C), and Ga-5 pct Zn (25°C). Therefore, the probability of a ternary eutectic was high. For reasons to be discussed later, aluminum could not be used as an alloying constituent, leaving the Ga-Sn-Zn system as the only one of interest for low-melting gallium-

Jan 1, 1953

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone, quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide, The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over-burden was dug by hand labor, dumped to the quarry floor and trans-ported to the dump in quarry cars, Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi-circle around the top of the quarry about 200 ft. from the face and about 50 ft, above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river: As quarrying pro-gressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp,, 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft, above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting hays into which the motors are raised whenever the river reaches flood stage.

Jan 1, 1938

By William D. Klopp, Joseph R. Stephens

Chromium alloys were coated with silicon, alumi-nuw, and boron by pack cementation. None of these simple coatings provided adequate nitridation/oxida-tion protection for a Cr -0.17pct Y alloy substrate as shown by a substantial Increase in the ductile -brittle transition temperature after air exposure for 100 hr at 2100°F. Iron-modified silicide coatings afforded good protection, holding the transition temperature of air-exposed specimens to 350° F compared to 200° F for uncoated unexposed specimens and 800°F for un-coated exposed specimens. Additional attractive cant-binations of modi-tying elements included Fe-mo, Fe-Mo-W, Fe-,Mo-W-Ti, and V-Mo-W-Ti. THE desirability of increased operating tempera-tures as a mcans of improving the performance of ad-vanced air breathing engines has resulted in emphasis on the development of materials with high operating temperature capabilities. Chromium, because of its relatively low density (7.19 g per cu cm), high melt-ing point (3410°F), and adequate strength upon alloy-ing, is a candidate material for turbine buckets and stator vanes of advanced air breathing engines. How-even, chromium is not without severe limitations, the major one being susceptibility to nitrogen embrittle-ment upon exposure to air at high temperatures.1,2 For example, a 25-hr air exposure of a Cr-5 pct W* * All compositions in wt pct. alloy at 2100°F produces a 600°F increase in the duc-tile-brittle transition temperature.' Although dilute alloying with such elements as yttrium, lanthanum, arid thorium3,4 or strong nitride formers5 has been shown capable of reducing nitrogen embrittlement, it is apparent that some additional form of surface protection, such as coatings or claddings, will be required for long time service in air breathing engines. Studies of aluiminide6 and silicide7 coatings and of nickel-base claddingsl on chromium alloys to date have suggested that these protection systems are inadequate. Of the aluminidc systems Studied,6 a simple aluminum and an Fe-Al coating on a Cr-5 pct W-0.1 pct Y alloy showed the lowest air exposure weight gains. However, the air exposures raised the ductile-brittle transition temperature of the coated specimens to above 1600°F from an initial level in unexposed specimens of about 500°F. A second in-vestigation for protection of Cr-5 pct W-0.1 pct Y employed gas pressure bonded alloy foils as protective claddings.1 An aluminized Ni-20 pct Cr-20 pct W alloy plus an unalloyed tungsten barrier layer gave the best performance with air exposure lives based on appearance and weight gains of over 600 hr at 2100°F. However, the bend ductile-brittle transition tempera-ture was increased to at least 1000°F after 100 hr at

Jan 1, 1970

By AIME

THE wind howls almost incessantly over the mining engineers working in the near desert that is the Division of Namaqualand, the upper Atlantic coastal corner of South Africa's Cape of Good Hope Province. But when these men at the U. S.-owned mines called Nababeep South and East O'okiep (pronounced Oh-keep) tell you about their achievements, they can be heard above the wind. For their O'okiep Copper Co. Ltd. now produces over half the Union of South Africa's annual output of 30,000 tons of copper metal. Moreover, it is a very decent sample of U. S. geotechnical imagination. financial daring, and managerial skill, all operating successfully in a

Jan 1, 1947