Search Documents

By Y. Turen, Y. Karakas, E. Candan, C. Sahinturk

In this study, wettability between sprayable tundish lining (MgO) and molten steel was investigated by using sessile drop method. Content of glass fiber (SiO2) in the MgO varied between 0 to 8 wt% whereas mean particle sizes of the MgO were 25, 75, 150 and 300µm. Experimental results revealed that contact angle (0) of sessile drop on the MgO was not altered by the addition of glass fiber up to 1 wt.% whereas above 2 wt.% addition decreased the 0 considerably. Contact angle, 0, increased considerably with increasing MgO particle size. SEM analysis showed deposition of glass phase was present at the interface as the finer MgO particles were used.

Jan 1, 2004

By N. Melnyk

"FOREWORDThis paper provides a unique description of a method devised for mining a very thick steeply dipping seam of soft gassy coal which was prone to spontaneous combustion. The editors con¬sider that the information in this paper should be important to those who may have to consider mining such seams again at some time in the future and therefore believe that the paper warrants reprinting in the present volume. The author was ask¬ed to review the paper and to add any additional relevant in¬formation. He provided the accompanying footnote, only a month before his death on April 22, 1982.IntroductionIn the past, the Cadomin Coal Company has opened four mines, all in the same coal seam or its folds. Three of these were opened from river level by horizontal entries or rock tunnels. and the fourth, the present working mine, by vertical shafts. This paper deals largely with some operating phases of this fourth mine, with which the writer has been associated.The seam worked here is a thick, steep, bituminous seam, and the writer feels there is a paucity of published data on the mining of such seams. Possible reasons for this are that such seams do not lend themselves to intensive development or mining, there is little chance to mechanize because of the extreme pitch, and operations are fraught with many problems. In addition the present operations in this particular' seam are being carried on at a level below the former workings, introducing new problems, not encountered on the upper level.Coal will, without question, long continue to be an impor¬tant factor in the national economy, and some of the best coal is to be found in thick, steep seams. But with the exhaustion of the easily-mined coal near the outcrops, future coal will have to come more and more from lower levels. At Cadomin there is still considerable coal on the second level, below the old river-workings, and there is a possibility that, in the future, still lower levels will be worked. It is the purpose of this paper to indicate some phases of such lower-level operations and to invite discussion."

Jan 1, 1985

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By F. W. Gray

Foreword: It is not my purpose, in this address, to write the history of the Geological Survey of Canada, which has from time to time been reviewed by the officers of the Survey itself, and by men more competent than myself to handle so large a subject, but rather to set out some of the reasons for the regard in which the Survey is held by our Institute, the body best qualified to speak for the mining men of Canada. And, a further purpose is to publish the desire of our Institute that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country. will permit, because to scrimp expenses on the Survey is 'to save at the spigot and lose at the bunghole." A historical examination of the grounds on which it may be asserted the Geological Survey has been, and still is, of fundamental economic value to our country, discloses a prescience on the part of the forefathers of Canada, calling for our admiring gratitude, and reveals a unanimity among the real leaders of Canadian thought, on the value of geological knowledge, that is impressive in its continuance dawn to this date. There seems always to have been before our people the realisation that large stretches of Canada are unfitted for agricultural settlement, and that our glaciated areas, the barrens and tundra of the North, and our extensive mountain ranges, had promise of compensating mineral content which the geologist and the prospector, labouring together through the years, would disclose. The Geological Survey is one of Canada's oldest public services, distinguished by an unimpaired tradition of honourable and useful labour. Founded in 1843, under William Edmond Logan, not yet 'Sir William', one year after the Act of Union, it was directed by him until 1869, or into the early years of Confederation, so that the early years .of the Survey were also, politically, the formative years of Canada, as we know her today.

Jan 1, 1932

By R. G. K. Morrison

As mines grow deeper, the problem of ground control becomes one of increasing importance. The literature on the subject has grown extensively in the past few years, but is still far from conclusive. Detailed and precise observations are on record covering most phases of the problem, and control measures have progressed to the point where, in a large measure, they are effective. The success of methods to date must be attributed to the efforts which have been exerted to reduce convergence of stope walls and to the realization that a regular progression of stope faces approaching longwall has a beneficial effect. This paper attempts to explain the relationship between these two factors and the general problem of ground control. The problem at present lacks the co-ordination of the practical with the scientific outlook, but fortunately as time goes on there are indications that our scientific friends are becoming more interested and more familiar with the practical issues involved. Opinions vary widely regarding the mechanism of the problem and there are several schools of thought, two only of which will be discussed. One associates the incidence of rock-bursts with the stresses built up by a sagging hanging-wall, while the other takes the view that stresses primarily responsible for the sagging hanging-wall are also the cause of rock-bursts. The first group starts its reasoning from the convergence of the walls, probably the most conspicuous feature of deep mining, and works back to the conclusion that rock-bursts are in sorne way due to the breaking up of the sagging layers. The second group begins with the stress zone apparent around excavations at depth and follows mathematical conceptions based on certain assumptions which, in the absolute sense, are known to be inaccurate, but which are justified by the similarity between the conclusions reached and the results obtained in practice. This reasoning is followed to the point where rock-bursts result from the failure, under stress, of rock in situ, quite independent of wall convergence.

Jan 1, 1939

By E. S. Moore

Introduction The geology of the Sudbury nickel field has been studied extensively, but there are few reports dealing with the structure of the interior of the basin. It was not until the Treadwell-Yukon zinc-lead deposits were discovered that attention was strongly directed toward the large-scale faulting that has split the basin parallel to its long axis. This faulting has been responsible for the , ore deposits in the basin and it may be regarded in many ways as the most important geological event, next to the intrusion and differentiation of the nickel eruptive sheet, that has occurred in the Sudbury region. The early reports on the nickel region by Bell, and Barlow, were chiefly concerned with the nickel-copper ores and with the formations of the region. Coleman was the first geologist to map the nickel eruptive as a continuous sheet around the belt and to emphasize its basin character. On the map accompanying his later report, he shows an important offset in the nickel eruptive at its southwest end, where the large fault cuts this portion of the basin, but the fault was not traced into its interior, as little detailed work was clone in the basin at that time. No ore-bodies had been developed outside of the nickel-copper deposits associated with the norite when the map was prepared, and attention was mostly concentrated on the nickel eruptive. Coleman did, however, map and name the various formations found within the basin and, in general, his delineation of these has remained the standard for prospectors and other workers in the field until the present day.

Jan 1, 1930

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By M. Oliazadeh

The bioleaching of fine low grade copper sulfide ore is described. A sample of ground (> 1 mm) copper ore from Sarcheshmeh, Iran, was subjected to a series of agglomeration procedures and subsequently leached. The best agglomerate was obtained by using lime and sulfuric acid as binders. A column bioleaching test of agglomerated ore was then run for 105 days along with a non-inoculated control column having thymol as bactericide. The results show that about 77.5% of copper was extracted in the bioleaching, whereas the control column achieved only 57% copper leaching.

Jan 1, 2007

By Mori Fresko, Stuart M. Jones Jr

"This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded.A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.INTRODUCTIONThis paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide. The list is maintained by Stuart M. Jones, Jr. (author), and is included in the appendix. This list has been the inspiration for similar papers in the past several SAG Conferences. Updates have been solicited from all major mill manufacturers and most have responded. Information from this list is compiled to illustrate the growth of the AG/SAG mill market and the use by industry and selected geographic areas. It covers the market growth through the end of 2010."

Jan 1, 2012

By W. S. McDonald

PRACTICALLY all dusts derived from organic matter are explosive and instances are recorded of explosions-some of them extremely violent-having occurred in grain elevators and flour mills. While a discussion of the explosibility of dusts in general, doubtless, would be of more than academic value, it will be of greater interest, on this occasion, to consider various phases of the problems connected with the hazards arising from coal dust. Extensive and valuable research has been carried out during the past few decades on the subject of coal-dust explosions and a great part of this work has been concerned with the preventive effect of stone or other incombustible dusts. Four men have been outstanding in this very substantial achievement. The first is Dr. W. Galloway, who succeeded in demonstrating by experiments that one pound of coal dust mixed with 150 cu. ft. of air formed an explosive mixture. The next is Sir W. Garforth, who proved that stone dust is an effective preventive for coal-dust explosion. The third is G. Haon, and last but not least, L. G. Hill, both of whom laboured incessantly to produce a suitable stone-dust and a satisfactory method of application. Today, mining men all over the world are satisfied and convinced that stone dust, if properly applied, will prove effective in greatly minimizing, if not completely preventing, explosions of coal dust, as has been demonstrated in experimental mines, as well as in actual explosions, in practically every coal mining industry.

Jan 1, 1938

By L. E. Djingheuzian

"ForewordTHE FOLLOWING excerpt is taken from Fine Grinding Investigations at Lake Shore Mines (C.I.M., Trans., Vol. XLIII, 1940, p. 307):""MacCalman, who has carried out exhaustive testing on the accuracy of screen analysis, makes the following statement in his report, The Accuracy of Sieving Tests, Industrial Chemistry (London, England), Vol. XIV, p. 231:"" 'It will be shown that, as no specific relationship between the sieving value and the various dimensional features of the sieve is evident, though there is an apparent tendency for the sieving value to follow the average aperture size, it is apparently impossible to define the sieving value of a screen from dimensions alone, and the calibration of sieves for important tests on a specific material, whereby the sieving values of these sieves are related to that of an arbitrarily chosen master sieve by correction values, will be recommended."" 'It will be emphasized that these correction values are probably not applicable to other materials, or the same material of different size composition. Sieve users, for important tests or in cases of dispute, will be recommended to calibrate their sieves against a mutually acceptable standard with specified conditions of test, and to recalibrate at intervals' ""."

Jan 1, 1953

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

By A. P. Fletcher, K. Croteau

The intent of this paper is to cover some aspects of preventive maintenance methods which have come into wider usage in recent years as a means of increasing operating efficiencies. Particular emphasis is placed on lubrication and related servicing.

Jan 1, 1967

By J. A. L. Henderson

THE potential oil-and gas-bearing area with "which this paper deals is the large undefined Carboniferous basin, roughly triangular in shape, occupying about 10,000 square miles of southern and eastern New Brunswick. Its base, about 135 miles long, lies on the gulf of St. Lawrence and embraces the whole eastern coast-line of the Province, while its apex lies in the south-west corner of the Province, near the International boundary (see map, Figure 1). The Carboniferous basin may be divided roughly into two areas-the Northern basin and the Southern basin-by a structural feature represented by a ridge of low hills running north-easterly from the Saint John river, near Saint John, on the southwest, to Indian mountain, about eight miles north of Moncton, in the northeast. Within the Northern basin, all evidence regarding the presence or attitude of the older Mississippian Albert Shale series, the only oil-bearing rocks known in New Brunswick, is for the greater part obscured by a thick and practically horizontal blanket of Pennsylvanian strata and, although evidences of oil and gas have been reported, none has been positively identified. Five parallellines of gentle folding, running to the northeast, occur in the Pennsylvanian rocks, within a distance of 100 miles from north to south. This folding is reflected in the courses of the rivers, which lie within the synclines. The relationship of the folding in the younger rocks to structures in the uncomfortably underlying older rocks is unknown, but should now be possible of clarification by means of a geophysical survey accompanied by drilling. Independent geological examinations have yielded no evidence of value in this respect, nor have five exploratory boreholes drilled by per-cussion tools to a maximum depth of 3,645 feet been of assistance, as only one inconclusive hole completely traversed the beds which normally overlie the Albert shales.

Jan 1, 1940

By J. A. Bossert

"In 1957, the Department of Mines and Technical Surveys (now Energy, Mines and Resources Canada) issued their first certificate for a fire-resistant conveyor belt. The testing procedure used was a combination of those used in the U.S.A. and the U.K. Subsequently, certification was granted to fire resistant electric cables (1974), fire-resistant mine duct material (1976) and fire-resistant hydraulic fluids (1978).Until recently, the testing procedures were copied from either the U.S. or the U.K. However, since the founding of the new Canadian Standards Association (CSA) Steering Committee for Electrical/Mechanical Mine Safety in 1981, these requirements have come under the close scrutiny of new CSA technical committees who will attempt to adopt or change the existing procedures to meet Canadian needs. This paper outlines the existing test requirements and attempts to predict how they will appear after ""Canadianization"" by the CSA committees.IntroductionFires in underground mines have always been considered more serious than in other locations because of the confined space and limited atmosphere. A fire can make escape difficult or impossible if it is blocking all of the routes to the surface. Also, the products of combustion from an underground fire can asphyxiate anyone not having self-contained breathing apparatus.In an underground coal mine, the consequences of a fire can be even more serious because of the presence of methane and coal dust in the atmosphere (which can explode) and because the coal itself is combustible.For these reasons, the inspection authorities having jurisdiction over underground mine s in Canada are quite concerned about the flammability of any materials that are used in quantity in the underground environmentAs early as 1957, the Canadian Explosive Atmospheres Laboratory (CEAL) was asked to certify conveyor belting as fire-resistant. This is because many miles of this material are used in underground mines in Canada and, as it generally travels through the mine, it is a perfect vehicle for spreading a fire."

Jan 1, 1982

By J. C. Loretto, H. A. Simons

The paper discusses how, in the routine testing of ores, insufficient communication between the laboratory and the design personnel can lead to misunderstanding or misinterpretation of test results and consequent design errors. A number of examples are given together with suggested modified interpretations and the resulting dollar savings indicated by these new interpretations.

Jan 1, 1972

By J. M. Newell, G. R. Peatfield

"The Red-Chris porphyry Cu-Au deposit is located between Ealue and Kluea lakes, southeast of the village of Iskut on the Stewart Cassiar highway in northwestern British Columbia. It was explored by Texasgulf Inc., in a joint venture with Great Plains Development Company of Canada, Ltd. and Silver Standard Mines Ltd., during the period 1973 to 1980. Exploration resumed in 1994, following acquisition of the interests originally held by Texasgulf and Great Plains Development by American Bullion Minerals Ltd.Prospectors were first drawn to the area by prominent limonitic stain zones exposed in creek gullies in the western part of the property. These zones are developed on the alteration halo at the western periphery of the deposit. The potential ore zones do not crop out and were first exposed in a bulldozer trench excavated in 1971. Subsequent exploration was by percussion and diamond drilling, guided to some extent by induced polarization surveys. In 1976, estimated resources contained within two crudely designed open pits were 41 million tonnes with an average grade of 0.56% Cu and 0.34 g/t Au, with a cutoff grade of0.25% Cu. New resource estimates based on a major drilling program completed by American Bullion in 1994 were released as this paper goes to press. These estimates were calculated using various copper cutoff grades; at the 0.4% Cu cutoff, the ""in-situ geological reserve"" is given as 100 million tonnes grading 0.58% Cu and 0.46 g! t Au (American Bullion Minerals Ltd., 1995).The deposit consists mainly of pyrite, chalcopyrite and increasing bornite at depth, in zones of quartz-vein stockwork hosted by an elongate body of altered monzonite porphyry of latest Triassic or earliest Jurassic age. The stock intruded volcanic and sedimentary rocks of probable Stuhini Group affinity and is in faulted contact with sedimentary rocks of the Jurassic Bowser Lake Group. Gypsum stockworks are developed in the higher levels of the subvolcanic porphyry system. Late-stage quartz-carbonate veins carry small amounts of galena and sphalerite. Complex faulting within the deposit makes drill-hole correlations difficult. Alteration assemblages include an early potassic phase, almost completely destroyed by later phyllic alteration, and surrounded by a propylitic assemblage dominated by ankeritic carbonates in altered sedimentary rocks.The deposit has characteristics of bath the alkalic and calc-alkalic classes of porphyry copper deposits. The development of quartzvein stockwork suggests a calc-alkalic affinity, but the hostrocks contain little or no free quartz, molybdenum is present in trace amounts only and gold values are significant. Copper grades vary between wide extremes with unusually high grades in some sections of the deposit. The weight of evidence available in the 1970s led us to place the Red-Chris deposit firmly in the alkalic family. The quartz-sericite alteration assemblage was attributed to breakdown of potassium feldspar in a near-surface alteration environment in which seawater may have had a significant role. These interpretalions are retained here, but preliminary conclusions from the most recent work suggest that they may require some modification."

Jan 1, 1995

By M. K. Gangal, A. E. Hall, S. B. V. Stewart

"An investigation into the problem of atmospheric fog in Canadian mines is described. Fog occurs in several mines and the reduced visibility can result in the closure of workings for safety reasons. Information on the mechanisms of fog formation are discussed and the methods for improving conditions are reviewed with their relative costs.INTRODUCTIONAtmospheric fog occurs in several Canadian mines during spring and summer. The fog which reduces visibility, contributes to loss of production and increased accident risk . Closure of ramps in mechanized mines causes mining to be stopped or rescheduled, and stoping and grade control may be affected . Increased corrosion of equipment may result from acidic fog .Fog is commonly caused by saturated air being compressed and heated by an inlet fan and then being circulated in an ascensional system with heat transfer to the walls of wet airways. This causes supersaturation and water droplets condense to create fog, with liquid water contents of 0.5 g/kg to 3 g/kg of air. These concentrations reduce visibility to less than 10m and prevent mining. Less severe fog is usually tolerated as a nuisance, about which little can be done."

Jan 1, 1989

By Erica J. Wanless, Ghislain Bournival, Seher Ata, Jose Hamilton Tavares

In froth flotation valuable particles are captured by bubbles and transferred to a froth layer where bubbles are in close proximity. Bubble coalescence frequently occurs in flotation, especially in the froth layer. The coalescence of two bubbles causes a release of energy, which may expel particles from the bubble surface. A series of experiments were carried out to determine the effect of bubble interfacial properties on the detachment of particles upon the coalescence of capillary-held bubbles of 2 mm in size. The interfacial properties of the bubbles were changed by the addition of low molecular weight alcohols, namely 1-pentanol or methyl isobutyl carbinol (MIBC). Using esterified glass particles (? = 43 °) with a 10 % and 90 % cumulative passing diameter of 47.2 and 92.5 µm, respectively, as model particles, it was found a certain concentration of frother, different for each additive, is needed in order to observe a reduction in the detachment of particles. In the presence of frother, the detachment was evaluated at approximately 65 % which was a considerable reduction in the detachment compared with the value of approximately 85 % found in the absence of frother. Frother molecules changed the properties of the airwater interface. Upon the coalescence of two bubbles, the release of energy caused the merged bubble to oscillate; effectively resulting in the detachment of particles. The addition of frothing agents augmented the elasticity of the bubbles, which appeared to be related to the detachment of particles. Whereas frothing agents are generally used to prevent bubble coalescence and stabilise the froth phase, only transient stability is imparted. The results suggested that an additional role of frothers in flotation is to decrease the detachment of particles from bubble surfaces. The type and concentration of frother can be strategically selected to improve metallurgical recovery as an economic incentive.

Jan 1, 2016

The Boleo project is located in Mexico close to the town of Santa Rosalia on the Baja Peninsula. The Boleo deposit contains copper, cobalt, zinc and manganese values as oxides with minor sulfides. The Boleo deposit is metallurgically challenging due to: 1) the requirement to recover four separate metals; 2) the presence of high levels of clay in the deposit resulting in difficult solid-liquid separations, and; 3) the need to use seawater for the bulk of the processing. Baja Mining, Bateman Engineering and SGS Lakefield Research have collaborated to develop and test a process flowsheet to recover copper, cobalt, zinc and manganese products at Boleo. The key steps in the flowsheet are: ? Feed preparation (scrubbing and ball milling of oversize) in copper raffinate ? Ore leaching using oxidative and reductive leaching ? CCD washing using high rate thickening technology ? Copper SXlEW ? Treatment of a bleed solution for cobalt, zinc and manganese recovery The process for cobalt, zinc and manganese recovery involves iron and aluminum removal followed by cobalt/zinc bulk extraction using CSIRO's DSX solvent extraction system and selective zinc and cobalt stripping. The zinc strip solution is evaporated to produce zinc sulfate monohydrate crystals to market and cobalt is recovered via a further SXlEW process as high purity metal. Manganese is precipitated as manganese carbonate from the DSX raffinate solution. This paper will review the Boleo process flowsheet and provide detailed results from the 2006 pilot plant operation conducted at SGS Lakefield in Canada.

Jan 1, 2007