Search Documents

By D. W. McDonald

Coal mining and railway transportation are so closely en-twined and so dependent one upon the other that the failure of one would mean the total collapse of the other. With this indisputable fact in mind, there is no doubt that the operator of each is deeply interested in the other's success. Railway transportation began at the mouth of a coal mine. The first railway car was the English coal-wagon, a crude box on four wooden trowlets, running on wooden rails and holding 1,600 pounds. This was operated by gravity or horse-power in England to convey coal from the mines to the rivers. The first coal-cars used on Nova Scotia railways were of 4 tons capacity with side doors and "V" shaped centres. Then followed flat-bottom, 4-ton cars that operated on tipples, the car bei.ng held in tipple by a chain passing over the top and fastened on either side. Next came the 6-ton car with drop-bottoms, then the 10, 15, 30-ton cars, and now the modern 50 and 100-ton steel cars, equipped with automatic couplers, brakes, and rachet dumping device. Contrast the first coal-car with a modern luxurious pull-man or a I 00-ton coal and ore car, and you have a record of progress in railway transportation. The development of the steam locomotive was no doubt the greatest factor in this progress, but let us not forget that the foundation of all industrial development was and is coal. and that development in mining and railway transportation should keep abreast.

Jan 1, 1924

By I. Protkova

Versa Power Systems solid oxide fuel cell (SOFC) stacks operate at intermediate temperatures 700 ? 800 °C allowing the use of metallic interconnects. Thermal expansion good matching with other stack components and cost restriction led to selecting ferritic stainless steels as interconnect material. Analytical tools and techniques were developed to understand the ferritic stainless steel behavior at high temperature while exposed to dual environment. Analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) have provided valuable information towards describing interconnect degradation in a variety of testing conditions. Several examples are presented to demonstrate interconnect oxidation and its relation with SOFC testing results.

Jan 1, 2005

By P. L. Lehoux, R. F. Lopes

"Unanticipated low recovery or extraction of gold from heap leachable are can often be attributed 10 phenomena such as non-uniform percolation (channelling) of solution through heaps, excessively slow percolation rates due to densification of ore during stacking on the pads and parasitic or competing reactions of the cyanide solution with undesirable elements or geochemical ""impurities"" in the ore. The nature and causes of these phenomena are discussed in this paper, and it is suggested that geotechnical and geochemical expertise can contribute significantly to a better understanding of the relationship between laboratory results and actual field performance of the leaching process. Recommendations are made for bench-scale metallurgical testing to be complemented by geochemical and geotechnical laboratory evaluations, to ensure more successful heap leach projects. IntroductionHeap leaching is a simple, low-cost method of recovering metals from low grade ores which has now come into widespread application particularly for gold and silver metals in the United States.The heap leach process involves percolating a lixiviant (leaching agent) solution through broken or crushed ore (Chamberlain and Pojar, 1984). In the case of gold a dilute sodium cyanide solution is used and crushed ore is ""heaped"" on specially prepared impervious pads.The potential for use of heaping leaching methods for northwestern Ontario gold deposits was discussed by Beard (1983), who suggested that the use of this extraction technique in Canada should grow significantly for low grade ores as well as for small high grade deposits which cannot justify the installation of a new mill or the use of remote custom milling facilities. Two other potential situations for lise of a heap leaching extraction method are : as a low capital cost cash generator in the opening phase of a larger new project, and as a low cost output augmenter to complement a milling operation."

Jan 1, 1989

By John A. Allan

The subject chosen for this paper is not a new one, but the subject matter is so extensive that something new can always be said .about it. We are just beginning to realize how little is actually known about the character of Alberta coal, except for a few general facts. The object of this paper is not to explain that our previous information, in whole or in part, on the coal resources of Alberta, has been incorrect, but rather to present some new facts obtained as a result of recent study in the field and in the laboratory. As field investigation continues the problem of determining the character of a coal seam for any great distance laterally becomes more and more complex. Our present knowledge of Alberta coal deposits should not be discussed before due reference is made to those great pioneers who blazed the trails for later geologists, by recording their observations on the general geology of Alberta. Geologists, to-day, particularly those of us who are striving, year after year, to unravel the mysteries of stratigraphy, palaeontology, and structure, in so far as these are related to the coal resources of Alberta, fully realize our indebtedness to those three trail-makers, Dawson, McConnell, and Tyrrell. Had these geologists not recorded their observations correctly, nor interpreted the broad geological facts contained in Nature's book, with still uncut pages, how much slower would have been the progress of our coal knowledge in the succeeding years. It is true that many of the interpretations given to observations by these pioneers have had to be changed as a result of closer studies, but we must also expect that the geological interpretation from present day observations will be changed by future workers, as Nature's book is read and re-read.

Jan 1, 1925

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013

By Y. Kusuda

Since 1981, the Annaka refinery has recovered zinc from zinc leach residues by the Waelz Process. The important considerations of this process are the prevention of the growth of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate. In this paper, simulation predictions and the results of the industrial operation regarding the prevention of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate at the Annaka refinery are reported and compared.

Jan 1, 2006

By P Kovacs, D. L. Flock

For the purpose of reservoir-performance calculations a balance can be made between the materials with-in the reservoir and the production from the reservoir. The material balance equation, a relationship which holds under or near equilibrium conditions, has been used in many forms by the Petroleum Engineer for the determination of initial oil-in-place in the reservoir and the calculation of performance into the future. One of the more recent methods developed by Tracy, utilizes a modified form of the Schilthuis material balance. In the latter case, values of incremental production are assumed for a particular pressure drop, a value of the gas-oil ratio found and a check of this estimate made by calculation"' the initial oil-in-place. Tracy's method utilizes an estimation of the instantaneous gas-oil ratio and by trial and error a value of the gas-oil ratio is

Jan 1, 1961

By John H. McKillop

Industrial minerals production in Newfoundland in--creased in gross value by a total of 175 per cent during the ten-year period from 1954 to 1964. The Province accounts for all of ?Canada's fluorspar production and contains one of the most important fluorspar districts in North America. It is also the only producer of pyrophyllite in Canada, and quite recently has become an important producer of asbestos fibre. Limestone, gypsum, brick shale, sand and gravel also ?Contribute appreciably to the expanding industrial minerals phase of the Province's rapidly growing mining industry. Geological diversity characterizes Newfoundland's industrial minerals: Pyrophyllite deposits were formed by contact metamorphism of predominantly volcanic Proterozoic rocks. Fluorspar deposits are fissure-filling veins having the characteristics of typical epithermal deposits. Chrysotile asbestos production comes from one of the Island's serpentinized ultrabasic belts. Limestone is produced at three localities; two of them in the extensive carbonate rocks of the west coast. Gypsum production comes from a thick evaporite (gypsum and anhydrite) sequence in the Carboniferous rocks of the St. George's Bay area. Introduction

Jan 1, 1965

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By H. Utsunomiya

Most magnesium alloy sheets show low deformability in rolling. Edge cracks and transverse fractures are common difficulties. In addition, rolled sheets show well-developed basal texture <0001>//ND. The texture causes high anisotropy in mechanical properties and low formability in subsequent metal forming. Differential-speed rolling, where the upper and the lower rolls rotate at different speeds, introduces shear deformation through the thickness. Not rolling texture but shear texture evolves in the sheet so that the asymmetric rolling can be a method of texture control. However the primary slip system of the hcp alloy, is basal, the shear texture should be also basal. Differences between the two basal textures, i.e., the rolling texture and the shear texture, have not been understood completely. In this study, conventional (same-speed) rolling and differential-speed rolling have been applied to commercial AZ31B sheets at 623K. Microstructures, textures and mechanical properties of the rolled sheets before/after annealing are compared. It is found that the basal texture is more pronounced by the asymmetric rolling. On the other hand, the asymmetric rolling is effective to decrease the grain size and the planar anisotropy.

Jan 1, 2006

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By D. Sediako

Excessive residual stress in Al engine blocks may result in cylinder distortion which reduces engine operating efficiency. As such, neutron diffraction was used to measure residual strain along the Fe liners and Al, in the hoop, radial and axial orientations with respect to the cylinder axis, at the cylinder interbore region. Residual stresses were subsequently calculated using generalized Hooke&apos;s law and related to the microstructure along the cylinder bridge. The results suggest that the residual stresses in the Al interbore region are tensile and increased with depth in the axial direction of the cylinder. The increase in residual stress at the bottom of the cylinder coincides with a finer and more uniform microstructure in this region of the cylinder. The refinement in microstructure at the bottom of the cylinder likely increased alloy strength, thereby decreasing this section&apos;s susceptibility to distortion. This study successfully quantified the residual stress profiles in a heat treated engine block and related the stress profiles to an as-cast engine block.

Jan 1, 2011

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By Reginals W. Burroughs

Diatomaceous or infusorial earth, also called diatomite; fossil meal, or kieselguhr, is derived from the lowest form of vegetable life, the unicellular alga:. It consists of the siliceous remains of extremely minute aquatic plants, which exist in both salt and fresh water. Light i~ a prerequisite to their development. These very small particles secrete silica in much the same way that molluscs secrete lime to form their shells. The diatoms at death sink to the bottom of the body of water in which they lived, and the organic matter gradually decays and is washed away, leaving the skeletons. Thousands of years are required by this means to develop bed5 of sufficient thickness to be of commercial value. The siliceous remains vary in size according to the species, but all are very minute and, as a general rule, they can be identified only under a high-power microscope. Over one thousand types have been distinguished and named. They are all composed of a hydrous or opalescent form of silica, with silica content ranging from seventy to ninety-five per cent. Magnified, they present an attractive sight, a very fragile structure with many interstitial openings known as cells. Many of them consist of two parts, defined as valves, held together by means of a girdle. Certain species, belonging to the Pinnularia family appear as a long comb, in half longitudinal section. The spaces between the teeth are the cells. This particular genus is very common in Nova Scotian deposits.

Jan 1, 1928

By V. G. Papangelakis, G. P. Demopoulos

"Recovery of gold from refractory ores and concentrates presently constitutes one of the most important, challenging, and exciting areas of R&D activity in the gold processing industry. New technologies are being tested for the treatment of refractory gold materials, some of which have been advanced to the level of commercial operation. In this paper, some recent technological developments in the hydrometallurgical processing of pyritic matrix-refractory gold ores are highlighted. Key operational steps of each of the alternate hydrometallurgical technologies are analyzed and potential advantages and drawbacks are identified. The processes which are reviewed are: hydro chemical oxidation, biochemical oxidation and pressure oxidation. INTRODUCTIONOver the years the term ""refractory"" has been applied in gold ore processing to denote situations in which straightforward cyanidation failed to yield high gold recoveries. A number of mineralogical and chemical factors may be responsible for this ""refractoriness"" problem. A systematic classification of the different options for their treatment has been discussed in a recent review paper. In this paper, the pretreatment of the submicroscopic gold encapsulated within the matrix of pyrite and arsenopyrite minerals is considered. This type of gold is the ultimate refractory material because complete breakdown by reaction of the host mineral structure is required.The method which has been traditionally applied for the treatment of pyritic-type refractory gold ores is an oxidation roast (single stage or double stage depending on the As content) of a flotation concentrate to produce a porous calcine, the latter being more amenable to cyanidation. Despite its established practice, oxidation roasting is not considered particularly attractive with today&apos;s standards for high product recovery and clean environment. Roasting is known to be very sensitive to heating parameters and feed composition and deviation from optimum conditions can result in reduction in permeability which is translated to incomplete gold liberation."

Jan 1, 1989

By H. D. S. Miller

"This paper introduces a new approach for the design of rib pillars. The approach involves an empirical method for pillar design and a discussion of the pillar stability used for open stope mining methods.The empirical method predicts the degree of stability of rib pillars. Pillar load is estimated using two and three dimensional numerical modelling. Rock strength and the shape effect of pillars are used to account for pillar strength. The method has been calibrated with case histories from Canadian open stope metal mines and is compared with other methods used [or pillar design.INTRODUCTIONThe role of rib pillars in open stope mining is to provide stability to a mining block by limiting rock mass displacements and restricting the exposure of a rock mass in stope backs and stope walls. They also provide flexibility in ore extraction by dividing a stope block into multiple working faces.The use of backfill in open stope mining methods has reduced somewhat the need for optimum pillar design. In contrast to permanent pillar methods, the dimensions do not need to be minimized because the pillars are usually recovered in a later stage of mining. However, the consequences of poor pillar design are often overlooked and can still be severe. A pillar that does not perform its intended role may result in excessive stope or pillar sloughing, difficult and expensive pillar recovery, loss of permanent access and remedial costs such as development rehabilitation, artificial support or low productivity.Pillar design concepts of the past were not developed for open stope mining conditions and generally have not been confirmed for open stoping. The focus of this paper is to introduce an empirical design relationship specifically for open stope pillars. It provides a stable, yielding or failed pillar assessment for a given design."

Jan 1, 1989

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By Ting An Zhang, Chengzhi Jiang, Xiujing Zhai, Feng Xie

The extraction and concentration of nickel from aqueous solutions by emulsion liquid membranes (ELMs) using tributylphosphate (TBP) as extractant has been investigated in this research. The emulsion liquid membrane consists of a diluent (kerosene), a surfactant (Span 80), a mobile carrier (TBP), and a stripping solution (ammonia solutions). Important factors influencing the separation process including membrane composition, feed composition, and mixing speed have been examined. The results show that more than 90% of nickel in the feed solution could be extracted by ELMs under the experimental conditions, indicating the feasibility to use the designated ELMs to detoxify nickel-containing industrial waste solutions.

Jan 1, 2014

By C. Gu

Flow field design is critical for PEM fuel cells. The flow field design can affect reactant distribution to the catalyst surface, water management, thermal management and current collection. Therefore, it has tremendous impacts on the fuel cell performance and durability as well as reliability and operational flexibility. In this paper, an optical method is used to study the reactant distribution in the flow field channels of two commonly used flow field designs, straight channel design and serpentine channel design. Images of the flow patterns are shown followed by discussions of the flow patterns.

Jan 1, 2005