Search Documents

By Adrian Moore, Dominic Hooton, Alan Richards

Significant factors affecting airblast overpressure (AOP) emissions include charge mass per delay, distance from the blast site, burden, stemming height, and delay timing, topographic shielding, and meteorology. The effect of charge mass on the frequency of the airblast produced, and the delay timing required to control the level of airblast overpressure is explained by two case history examples which were not affected by topographical shielding and meteorology. One is a cast blast with a charge mass per hole of 1000 kg (2200 lb), and the other is a quarry blast with a charge mass per hole of 64 kg (141 lb), These examples show that the delay interval necessary to prevent an increase in AOP levels must be increased with an increase in charge mass per hole. The effect of a ‘soft-start’ technique where a reduction in AOP levels is achieved by decking only the initial front-row holes is also illustrated.

Jan 21, 2025

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Mark Bosse

This is a paper demonstrating the use of a fixed wire and trolley system to deliver 2 or 5 lb cast primers (with 2 meter cap/fuse assemblies) deep into avalanche terrain. This avalanche terrain is mitigated using explosives prior to being opened to guests.

Feb 1, 2020

By Jason Baird, Braden Lusk, Dominique Nolan, Allen Stults

Conical shaped charges have been used to penetrate rock for many years now. Examinations have been made looking at shaped charge liner geometry, material, and standoff, as well as explosive composition, confinement and initiation. Most of the testing conducted towards penetration rather than cratering has fallen within the realm of the petroleum industry and as such been confined to specific rock types, with test apparatus that include simulated down hole (subterranean) environments. The testing conducted within this experimentation is conducted at ground level, in small scale samples, using a single standoff, against multiple rock types. The data collected from that testing is examined here and relationships between physical properties of the rock and the liner are analyzed. The analysis of that data raises the possibility of a relationship that may lead to new empirical methods of penetration prediction in rock.

Jan 1, 2012

By Stephen G. Rieben

Almost everyone has at least heard of the two one-call systems which serve New England. They are "Call Before You Dig", which covers Connecticut, and "Dig Safe", which covers the remaining five New England states. Those of you who are more familiar with these programs know that it is our job to help guard against the accidental dig-ups of buried plant and to prevent facility service disruptions. We cover all types of buried facilities, from cable television to high pressure gas transmissions lines, telephone cables, electric facilities, fiber optics and everything in between

Jan 1, 1990

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By John Atkinson, Steve Repola

This paper will describe two blasting plans that have been developed for American Aggregates' Marble Cliff Quarry located near Columbus, Ohio. Two different limestone formations are mined on different levels of the quarry. Each formation requires a different blasting plan which address vibration considerations, crusher productivity, drilling and blasting costs and adjacent neighborhood concerns. Controlled blasting is critical to continued mining operations in this Midwest urban setting.

Jan 1, 1993

By Kahmmelly Mathildes Pimenta Coelho, Felipe Dantas, Jaine Ribeiro de Souza, Augusto Ferraz, Carlos Roberto Campos Junior, Davi Bastos Martins de Oliveira

The Carajás Iron Mine, recognized as the largest iron ore province in the world, is notable for its continuous efforts to improve operational efficiency and safety. In response to these objectives, a QA/QC (Quality Assurance and Quality Control) Program was implemented and integrated with Blastscout Probe technology to optimize drilling and blasting processes. The program supports the standardization of operational parameters, the execution of regular audits, and real-time data analysis, facilitating precise and timely adjustments. The implementation led to significant improvements, including an 80% increase in operational compliance, a 49% reduction in drilling depth deviations, and a 30% enhancement in Jaspelite fragmentation. This study presents the methodology employed, the outcomes obtained, and the positive impacts observed in both operational performance and environmental management.

Jan 26, 2026

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By Joseph Kennedy

How do terrorists and other criminal bombers acquire explosives to be used in an attack against U.S property and/or citizens? The Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) with nearly 40 years of investigating bombings and other explosives incidents, has learned that explosive materials intended to be used in criminal acts are obtained primarily by theft, clandestine manufacture or diversion.

Jan 1, 2010

By Stephen Mansfield, Saran Sankar

The Sentinel open pit copper mine, operated by First Quantum Minerals Ltd, is located in the North West province of Zambia. The Sentinel orebody is a sediment-hosted, structurally modified deposit in which mineralisation is contained in the phyllite formation, which occurs as a series of layered, continuous sheets having a northerly 20 to 30⁰ dip. The persistent nature of the geological structure can lead to the generation of large slabs when joints are relatively close together or very large blocks when joints are more widely spaced. With standard blasting methodologies, the challenging fragmentation most commonly occurs in the stemming zone and blast interfaces, reducing excavation rates and increasing the risk of crusher bridging events and reduced throughput. A generalised approach to increase powder factor would increase in drill and blast costs and would not be sufficient to target the specific cause of the challenging fragmentation. Implementing differential blast energy based on post blast requirements for different material type, such as ore and waste, and rock mass characteristics is not new in the mining industry. High-energy blasts for ore aim to produce finer materials, enhancing downstream processes such as crushing and grinding, while reducing power consumption and increasing throughput. Conversely, waste rock often requires less energy in order to deliver optimised fragmentation for loading and hauling efficiency. Identifying and applying optimum blast energy to specific material type and geological domains will not only ensure smoother and efficient operations throughout downstream processes, but will have a direct impact on overall profitability of the entire operation. This paper will describe the methods used to model and implement differential blasting across a range of material types in order to deliver the required blast outcomes for ore and waste and the impact on downstream processes and drill and blast unit cost.

Jan 21, 2025

By R Yang, P D. Katsabanis, W F. Bawden

Understanding the mechanisms which are taking place during the propagation of a stress wave generated by an explosive charge is of high importance in the detection, characterization and prediction of blast induced damage to the rock. Vibrations caused by the detonation of an explosive are suspected to contribute significantly to the extension of the damage zone. Vibration monitoring close to a blasthole is a relatively new field of research, the hindrance being the scarcity of transducers capable of sustaining extreme accelerations without damage. This paper focuses on the vibration monitoring aspect of a blast induced damage study; the experiment took place at Queen's test site and was meant to record near-field vibration as close as 1 m from 100 mm diameter blastholes.

Jan 1, 1993

By D. Scott Scovira, Remi Proulx

The Meikle Mine is a high grade, underground gold mine utilizing primary-secondary longhole open stoping with delayed backfill to produce 3000 stpd of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 330” F were measured. In the early stages of mining, the mine experienced premature detonations using different explosives. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By Lon Santis, Michael Swisdak, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc. (APT) have developed a quantitative risk assessment tool called IMESAFR (IME Safety Analysis for Risk) for managing risk from various activities undertaken in the commercial explosives industry. The first version was completed in 2006 and Version 2.0 of the software was completed in 2012, incorporating several major new features. The platform is now based on a Geographic Information System (GIS), providing a bird’s-eye-view to help visualize facility layouts and risk. Spatial data on potential explosion sites and exposed sites can now be automatically transferred from the images to ease users’ data input. Use of GIS data provides the ability to check facility compliance with quantity-distance (QD) standards such as the American Table of Distances (used by the Bureau of Alcohol, Tobacco, Firearms and Explosives, ATF), the NATO standard (used by Natural Resources Canada and other nations), or a user-defined table. Research conducted and knowledge gained over the last 10 years enabled changes in the algorithms and models that provide greater fidelity and reduce conservatism. Expert users can change global settings to more accurately match actual site conditions and the program runs using either Imperial (English) or SI (metric) units of measure. These changes and other new features are discussed and demonstrated.

Jan 1, 2013

By Alexander Hauck, Dimitri Jung, Uli Leiste

This paper describes results from small scale tests conducted to determine the distribution of impulse on target plates when subjected to loading due to the detonation of a buried mine. The tests were conducted with saturated sand, dry sand, and water as the loading media. Tests were conducted for flat plates and for plates with angled bottoms. Previous testing has shown that angled bottoms can reduce the total vertical impulse delivered to the vehicle significantly. Different stand off distances were investigated as well as loading of the targets both on center and off center. It is very important to know not only the total impulse delivered by a detonating charge but also how this impulse is distributed over the bottom of the vehicle. A complete understanding of specific impulse will permit those parts of the vehicle, taking the greatest amount of loading, to be sized properly. Experimental results were compared to analytical expressions provided by Westine and Tremblay.

Jan 1, 2010

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By Jhon Silva

"Signature Hole and Waveform Superposition techniques used to predict and control mine blast ground vibrations require a clearly defined information collection configuration. The collection of this information determines the scope and success of the ground vibration prediction. Application of the Improved Signature Hole technique using the Silva-Lusk equation requires the collection of at least two informational elements from any specific production shot. The first required element is a signature waveform, and the second element is the overall production blast waveform. The signature waveform depends on detonated charge variables such as the amount of explosive in use, use of decking, the possible detonation of several holes at the same delay, and many others. The production blast waveform is beneficial to the Improved Signature Hole methodology when used to calibrate the model, and toobtain accurate vibration predictions for different timing configurations."

Jan 1, 2017

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By Tapan Goswami, Geoff Keith

"At Bulga Coal, the objectives of drilling and blasting are to maximise safety and to minimise the totalcost of mining. A recent audit of two overburden blasts established that the standard of drilling and blasting is excellent. No apparent hazards were identified. Laser profiling showed that highwall free faces are reasonably planar with some exceptions, thereby promoting uniform burden distances along front-row charges. However, in three isolated areas along one face, small burden distances existed. The mean and the standard deviation of errors in the collar positions of front-row blastholes was found to be 0.3 + 0.03 m. A borehole video camera was used to show that blastholes did not feature open bedding plane partings, cavities or damage produced by the blast in front of them."

Jan 1, 1999