Search Documents

By Ralph D. Daley, Kevin E. Redinger

The production of coal/water fuel (CWF), a highly loaded mixture of finely ground coal, water, and chemical additives, presents a unique opportunity for significant ash and sulfur reduction through physical coal cleaning. Froth flotation can be integrated with the staged, wet, fine grinding inherent in the CWF production process. A laboratory scale research program was conducted to demonstrate the feasibility of a flexible, integrated coal cleaning/CWF process flowsheet. Performance of the conceptual flowsheet was examined for two coals of CWF commercial interest, Upper Freeport and Pittsburgh seam coals, from central and southwestern Pennsylvania, respectively. Several multi-stage coal flotation and reverse flotation circuits were evaluated. CWF was produced from the cleaned coal in each case at similar solids loadings and viscosities as observed for the raw coal. However, the ash loading and SO2 emission potential for each CWF had been significantly reduced.

Jan 1, 1988

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By Francisco J. Escandon V.

Numerous lead-zinc-barite-fluorite ore deposits, with simple mineralogy and roughly concordant with bedding, are found widely distributed all over the world, having been denominated and well described as "stratiform deposits" or "strata-bound ore bodies", not having any genetic relationship. During several years, its origin has been discussed, without getting to general agreement regarding the main mining districts of this type. Through studies made of large stratiform deposits in the United States, Europe and Russia, it has been found that there are, within this classification, syngenctic diagenetic and epigenetic ore bodies. During the Symposium about the genesis of the stratiform lead-zinc-fluorite-barite deposits, carried out in New York in 1966, Frank G. Snyder (1), presented an excellent analysis of the theories of the origin of these deposits and of the evaluation of the criteria regarding classification. As per his definitions (Table 1), "a deposit is syngenetic if formed by processes similar to and simultaneously with the enclosing rock, epigenetic if introduced into a pre-existing rock and a diagenetic origin implies deposition of metals with the host sediments but with recrystallization, rearrengement and limited migration".

Jan 1, 1974

By E. Stone, R. Reagan

Risk of hand injury is very real for operators carrying out conventional bolting operations with power torque tools, reaction arms and backup wrenches. Bolting operations of this type are common today in the installation and maintenance of heavy mining machinery and equipment. Newer solutions have become available that have the potential to dramatically reduce the risk of hand injuries in mining applications. MINING APPLICATIONS Within the scope of mining operations, various types of equipment are used such as tunnel boring machines, bucket wheel excavators, draglines, material handlers, screens, pumps, crushers, continuous miners and longwall systems. Design of these machines typically includes larger diameter bolts for strength and durability. Due to rugged use all machines require frequent maintenance and service which requires the use of heavy industrial bolting tools and methods. Those engaged in bolting operations include technicians working for end-users, equipment manufacturers, general contractors and others who provide services in mining operations. Most all personnel involved with these activities are engaged with use of high power bolting tools and procedures. Training is essential to raise the awareness of bolting safety and to avoid accidents. However improved bolting tools and procedures can play an even more significant role in further improving the safety of all those engaged with bolting in the mining industry. SAFETY CONCERNS Professionals working in the mining industry are constantly looking for ways to further reduce risk to health and safety. Bolting operations which are fundamental to service and maintenance of mining equipment are often overlooked as a potential area for improvement. Several areas of bolting operations offer potential for improvement in safety and avoiding accidents during equipment maintenance. This paper addresses the safety concerns associated with reaction arms and backup wrenches in conventional bolting applications (Figure 1).

Jan 1, 2019

By Fulian He, Jianhang Chen, Shoubao Zhang

"Fully grouted rock bolts have been used in mining industry for many years. Significant research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs. However, compared with that, less work has been conducted with analytical modelling. Therefore, in this paper, the authors used an analytical model to study the load transfer behavior of fully grouted rock bolts. To confirm the credibility of this analytical model, an in-situ pull-out test was used to validate this model. There was a close match between the experimental result and the analytical result. Following this, a parametric study was conducted with this analytical model. The influence of coefficients, Young’s modulus of the rock bolt and the diameter of the rock bolt on the load transfer performance of rock bolts were studied. Furthermore, the load distribution along the fully grouted rock bolt was analytically studied. The results show that the axial load in the rock bolt decayed from the loaded end to the free end independent of the pull-out load. However, the trend of the load distribution curve was influenced by the pull-out load. This paper was beneficial to better understand the load transfer mechanism of fully grouted rock bolts.INTRODUCTIONRock bolts have been used in the mining industry for a long time. They are used as the reinforcement tendons to keep the stability of openings in underground mining and the slope in open-pit mining. Furthermore, rock bolts are commonly used not only in the mining engineering, but also in civil engineering (Thompson, Villaescusa, and Windsor, 2012).The rock bolt is a tendon which can be a rod or a cable inserted into a borehole drilled in rock masses or soils. Traditionally, the material of rock bolts was steel. However, engineering practices showed that the steel rock bolts can be easily corroded by the moist environment in underground mines. Next, Fiber Reinforced Polymer (FRP) was used to manufacture rock bolts, which are termed as FRP rock bolts. Experimental results proved that the FRP rock bolts can effectively reinforce the surrounding rock masses without being corroded (Wang et al., 2018)."

Jan 1, 2019

By Arthur S. Radtke

The structural setting of disseminated-replacement gold deposits of the Carlin-type and other aspects of their genesis are closely related to events which took place during the evolution of the Basin and Range province. The deposits formed as a result. of chemical and physical processes which took place at shallow depths in the roots of hot spring systems at moderate temperatures (about 200°C) and low pressures (about 25 bars) (Radtke and Dickson, 1974). Locations of Carlin-type gold deposits in the Basin and Range province are shown in Figure 1. Most of the block-faulted mountain ranges in the Great Basin formed by tectonic activity that happened since Miocene time, although faulting in some places probably began in Eocene to Oligocene time (Hamilton and Myers, 1966). The Carlin-type deposits are spatially related to Basin and Range-type faults: Many deposits, such as Getchell, Pinson, Preble, and Cortez, occur along the flanks of ranges, while other deposits, including Carlin (Radtke, 1974) occur within the ranges in areas characterized by crosscutting and intersecting high-angle or Basin and Range-type faults. The association of the ore deposits with Basin and Range-type faults is evidence that ore deposition is young, Miocene or later. The steep, high-angle faults played three roles: first, they provided deep channels for upward-flowing solutions; second, in preparing the rocks for fluid penetration by brecciation and general rock dislocation; and third, they moved sedimentary carbonate rocks, favorable for ore deposition, from deep levels to near-surface positions where the physico-chemical conditions were more suitable for the deposition of ore.

Jan 1, 1976

By Robert D. Talvensaari

It is indeed an honor for White Pine, as a member of the copper mining industry, to participate in this Rapid Excavation Conference. Although our presentation, as the title indicates, is not a success story, we foresee, through our experience, future application of boring machines and rapid excavation equipment in the hard rock mining industry. One might ask what a copper mining company would be doing with boring machines and why the gamble on a high-cost, capital investment for a relatively untried application. Perhaps a little background on the White Pine mine and its geology will explain our daring and speculative motives. THE WHITE PINE MINE The White Pine Copper Company, a wholly-owned subsidiary of Copper Range Company, operates a mine, mill and smelter at White Pine, Michigan in the western Upper Peninsula approximately 6 miles due south of Lake Superior. We employ approximately 3,000 people from the surrounding area and mine approximately 25,500 tons of low grade (1%) copper ore per day. The orebody is contained within several distinct sedimentary horizons that comprise the lower 20 feet of a Precambrian formation known as the Nonesuch Shale. Numerous articles and reports have described many aspects of the White Pine operation and the geology. I will brief you only on that criteria which precipitated our interest in rapid excavation equipment and techniques, specifically, boring machines. Mineralogical and optical studies have demonstrated that the siltstones, sandstone and shale beds all contain relatively barren and discrete particles of quartz (25%), feldspar and mica, bonded with

Jan 1, 1974

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines as a means of re-covering copper and silver from a sulfide concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained Cu, Ag, Pb, Zn, Sb, and As. Parameters affecting metal extraction, such as temperature, pressure, amount of ferrous chloride, and initial hydrogen ion concentration, were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per?square inch gage (psig) and 1000 ?C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, Sb, As, Pb, and S reported to the tails.

Jan 1, 1978

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

By David Caiden, Petros Fortsakis, Alan Hodgkinson

"1. INTRODUCTIONDo contractual practices affect project outcome? Can better contractual practices improve the likelihood of project success? The consensus amongst experts is that better contractual practices really do improve project outcomes. With this in mind the members of the International Tunnelling Association (ITA) Working Group 3 on Contractual Practices (WG3) pooled their collective knowledge to publish in 2011 the document entitled The ITA Contractual Framework Checklist for Subsurface Construction Contracts (ITA Working Group 3, 2011). Written for projects involving significant subsurface works, e.g. tunnels and caverns, the ITA Framework Checklist explains the major contractual issues that must be considered to ensure a successful project. Its goal is not to specify how each issue should be resolved, but rather to highlight the issues and give recommendations on how they should be addressed. The Checklist is compatible with, and provides guidance for reviewing, standard contracts such as FIDIC and NEC. One of the authors is a co-author of the Checklist and has contributed to previous papers describing the Checklist and its applicability to hydropower projects (Hodgkinson & Wilson 2014, Hodgkinson & Wilson 2015). The Checklist identifies a series of issues that should be contractually defined, which can be summarized as follows: •,Methods for dealing with geotechnical uncertainties should be defined in the contract •,There should be an appropriate level of geotechnical/geological investigation •,Sufficient mobilization periods should be allowed •,Sufficient time should be allowed for testing and commissioning •,Procedures for timely dispute resolution should clearly defined •,Quality and performance requirements should be clearly defined and measurable •,Provision should exist for cost consequences of unforeseen circumstances •,Dispute resolution processes should be clearly defined •,Payment processes should be fair and clearly defined •,Risk should be clearly allocated and parties should be able to bear the risks they carry •,There should be a mechanism for adjusting payments according to conditions •,The risk management approach should be clearly defined •,Admeasurement or unit price approaches are recommended •,The responsibilities of each party must be clearly defined •,The consequences of non-performance should be clearly defined •,The construction programme (schedule) should be realistic."

Jan 1, 2016

By George A. Desborough, David L. Fey, Stanley E. Church

About 100 mine-waste dumps from past metal exploration and mining in Colorado and Montana were sampled using surficial-sampling methods for laboratory studies of the minus-2-mm fraction. In the laboratory, the composite samples were split into l00g samples that were leached to assess their acid-generation potential and associated release of potentially toxic metals that may degrade water quality in the headwaters of the Animas River watershed in Colorado and the Boulder River watershed in Montana. Two leach methods were studied: a passive leach using de-ionized water, and a more aggressive leach following the EPA-1312 method. The resulting pH values of the leachates using both methods are comparable. The concentrations of sulfate and several, but not all, dissolved or water-soluble metals are higher in the EPA-1312 leachates than in the passive leachates; however, the overall trends of the data are very similar. The passive leach method is less labor intensive and may be more representative of the natural weathering process occurring on the mine-waste dumps, simulating the natural precipitation and snowmelt. Three chemical characteristics of mine wastes studied here provide a relative ranking of mine-waste dumps for the purpose of determining priority for removal or remediation. These characteristics are: net acid production (NAP), sum of dissolved toxic metals (?As+Cd+Cu+Pb+Zn), and dissolved iron in leachates. Ranking can be done evaluating plots of NAP versus the sum of dissolved toxic metals, and NAP versus dissolved iron. These two plots serve as a basis for relative ranking of polymetallic-vein and acid-sulfate mine wastes studied. This ranking scheme may apply to mine wastes from production of other deposit types in other watersheds.

Jan 1, 2000

By R. O. Vernon

The Florida Peninsula has existed as a part of a much broader plateau, since at least the Early Cretaceous. This plateau, the Floridan Plateau, now consists of the present peninsula and a broad submerged shelf of equivalent size extending the length of the state and out into the Gulf of Mexico. Florida Peninsula was separated from the mainland United States by a negative area called the Suwannee Straits. To the south of this feature existed an environment similar to today?s Bahamo Banks where very pure calcium and magnesium carbonates with associated evaporites were deposited. Thus the Eocene and Oligocene contain little or no quartz sand or clay minerals except in the Panhandle west of the Suwannee Straits where some clastics were contributed by rivers from the north.

Jan 1, 1966

By Richard J. Wilson

The importance of coal as a major source of energy used by the steel industry has been increasing due to the gradual changeover from steel- making by the open hearth process to steelmaking by the basic oxygen process. Since the production of steel by the BOF process increases the demand for hot metal, there is a growing need to ensure the supply of coke required for the production of hot metal. Coal used for cokemaking has become, therefore, an increasingly important raw material for the steel industry in recent years. Our current projections indicate that coal will be the source of 71% of the total energy requirements of Inland Steel Company in 1985. As a result of the energy shortages of the last few years, various conservation programs have been initiated by the steel industry to reduce the consumption rate of fuel. The efforts to conserve energy have been successful to a great extent due to the rapid advances made in the technology of ironmaking that facilitated gradual reductions in the quantity of coke used per ton of hot metal produced in the blast furnaces. The decrease in the consumption rate of coke was made possible by the use of improved raw materials, such as iron ore pellets and fluxed agglomerates, the operation with high blast temperatures, the injection of auxiliary fuels, and the enrichment of the blast with oxygen. It is expected that additional reductions in the fuel consumption rate will be possible in the ironmaking operations of the large blast furnaces that are being equipped with facilities for proper burden distribution and for operation with higher blast temperatures at high top pressure. The purpose of this paper is to show the effects of coke quality on the production of BOF steel. The importance of coke quality will be pointed out by discussing the effects of the physical strength of coke on both the blast furnace productivity and the steelmaking operations of an integrated steel plant, such as Inland Stee1 Company.

Jan 1, 1980

By Kelly F. Bailey

The issue of regulating non-asbestiform varieties of the amphiboles actinolite, tremo1ite, and anthophyllite to the same degree as asbestos has been studied in detail by the National Stone Association. The ramifications of such a regulation, and the over simplistic regulatory definition of a fiber, are enormous not only for the aggregate industry and its users, but also for the nation. Evaluation of the health, geological, mineralogical, technical, economic and legal issues do not support an "asbestos-like" regulation of non-asbestiform minerals. The adverse consequences of regulating non-asbestiform varieties of actinolite, tremolite and anthophyllite like asbestos would be magnified many times if a similar standard for generic mineral fibers were promulgated.

Jan 1, 1988

By Alan G. Fricker

Cyprus Gold NZ Ltd will be recovering residual free cyanide in barren gold pulp by air stripping. Laboratory investigations by DSIR have indicated additional advantages by recovering the cyanide from pregnant pulp. These are a lower leach pH, a greater cyanide recovery and less carbon consumption. They have a net economic advantage of $1.20/tonne over recovery from barren pulp. The realisation of these advantages is dependent on three crucial technical aspects -optimum pH for dissolution, the absolute loss of cyanide and the stability of the aurocyanide ion. The laboratory investigations described herein address these aspects. Earlier work had indicated that the rate of dissolution of freely revolving gold discs at constant cyanide ion concentration increased with decreasing pH from 11 to 8. Attempts to repeat the work in a more controlled manner by measuring the corrosion potential and current density have, to date, not been reproducible, but do not contradict the earlier observations. Cyanide recoveries and balances were obtained on leaches at pH 10.5 and 9 at the same cyanide ion concentration -the lower pH requiring three times as much total cyanide. Unaccounted-for losses, unfortunately, exceed the accounted-for losses, making interpretation of the balances difficult. Nevertheless, it appears that the additional amount of cyanide at the lower pH of 9 may not be fully recoverable. It may not, however, prove necessary in practice to use more cyanide at a lower pH. Both the gold and silver cyanide complexes remain available for carbon adsorption, as do mercury, copper and iron. Zinc, and probably cadmium, nickel and lead, may precipitate during stripping, which is an environmental advantage.

Jan 1, 1991

By J. E. Moyle

Rio Algom Corporation of Wilmington, Delaware is a wholly owned subsidiary of Atlas Alloys Inc., an Ohio Corporation, which in turn is 100% owned by Rio Algom Mines Limited of Toronto, Canada. Rio Algom is controlled by the Rio Tinto Zinc Corporation of London, England, which has subsidiaries and affiliated operations throughout the world. Rio Algom geologists first became interested in this Utah pro- perty in 1966, after preliminary drilling had indicated that a known orebody close to the surface appeared to continue on the dorm thrust side of a major local fault, known as the Lisbon fault. Accordingly, in 1968, arrangements were made to acquire what was known as the "Humeca Option", a total of 2,573 acres located in San Juan county in south-east Utah, 35 miles south-east of the town of Moab.

Jan 1, 1975

By W. A. Heitbrink, M. Schmitz, J. A. Organiscak, A. B. Cecala, E. Ahrenholtz

Mobile excavation equipment operators at surface mines generally have the highest exposure to airborne respirable silica dust. Operator cabs on newer equipment are usually enclosed and equipped with heating and air conditioning systems. Many newer cabs are also equipped with air filtration systems. However, some newer cabs and many older cabs have either inefficient or no air filtration systems. The U. S. surface mining industry is still populated with older equipment and many of these have cabs that provide little or no respirable silica dust protection. Collaborative field studies were conducted as part of a partnership involving NIOSH, Clean Air Filter®, Red Dot, MSHA, and several mine operators to demonstrate that effective dust protection can be provided by these cabs at a nominal cost to mine operators. This effort encompassed adding an external make-up air fan and filter system to a retrofitted roof-mounted heating and air conditioning system in three older equipment cabs, and attempting to seal the cab enclosures to achieve interior cab pressurization. Abetter than 90 percent dust reduction was measured inside two of the three enclosed equipment cabs. It was possible to achieve positive cab pressurization inside these two cabs. A less significant dust reduction was measured inside the third cab, where positive pressurization was not achieved. These field studies demonstrate the key elements needed to improve enclosed cab dust protection in a cost-effective manner.

Jan 1, 2003

By C. E. McFarland, N. W. Kirshenbaum

Cortez Gold Mines is located about 75 miles southwest of Elko, NV. Activity in the mining district dates from 1862. The current operation developed from a 1963 joint venture of Webb Resources, The Bunker Hill Company, Vernon F. Taylor, Jr., and American Exploration & Mining Co. Three years later, the USGS discovered gold on the property following a regional geochemical survey. Drilling in 1966 and 1967 identified 3.4 million st of oxide ore grading 0.28 oz Au/st, and a 1700 st/day countercurrent decantation mill was commissioned in 1969. Heap leaching started in 1971 on low grade ore and continues to the present. The mill was shut down in 1976 following exhaustion of known oxide reserves. Mobile equipment was sold and the proceeds committed to local exploration. In 1980, a new plan of operations was developed starting with existing low grade and newly discovered mill ore. The mill resumed operations in 1981 and has been operating to date. A series of metallurgical innovations, culminating in the commissioning of a new fluid bed roaster in the summer of 1990, has enabled treatment of a series of increasingly refractory ores. Current partners in the venture are Kennecott Corporation, Vernon F. Taylor, Jr., and Placer Dome U.S. Inc., manager of the operation. Idaho Mining Corp. holds a 7.5% carried interest.

Jan 1, 1992

By Barbara C. Williams

U.S. Bureau of Mines researchers conducted field studies at an abandoned copper-gold mine tailings impoundment. Pore water quality was analyzed in the vadose and saturated zones. Three statistical procedures were employed to summarize the variability within and between the two zones. The results indicated that linear combinations of those variables reflecting sulfide oxidation and aluminum-silicate weathering best summarized the variability in each zone, and that the zones were most different on the basis of sulfide oxidation variables. The geochemical computer code WATEQ4F was used to assess the solubility status (saturation index) of minerals. Saturation indices of sulfide oxidation and aluminum-silicate weathering minerals were different in the two zones. It was demonstrated that the statistical analyses produced similar and complementary results to the geochemical code.

Jan 1, 1992