Search Documents

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By K. R. Miller

Thunder Basin Coal Company has two mines located in the southern portion of the Powder River Basin. 60-90 km southeast of Gillette, Wyoming. The mines are principally located on federal coal leases acquired in the late-1960's. Development plans for the Black Thunder Mine focused on dragline stripping, but environmental considerations during the mid-1970's made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lying with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age and the deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21 m thick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By J. A. Herbst, L. B. Hales, R. Zaragoza

INTRODUCTION The Control Problem The need for automatic control in flotation plants stems from frequent and randomly occurring disturbances to the feed slurry. Typical disturbances occur in the solids feedrate, the slurry percent sol ids, and the mineralogy and flotability of the gangue and valuable minerals. In plants where semi -autogenous grinding mills (SAG) are used, feedrate changes are very large and changes in feed percent solids of 1m or more are common. Mineralogy changes between valuable minerals are common, as are changes in the host gangue rock. As these changes occur, the operator can attempt to compensate for them by making adjustments to the flotation cell levels, the dosage rates of the collectors and frothers, the pH, and in some cases the aeration rate of the cells. This problem is sometimes complicated by the fact that different sections of the flotation plant will be processing different ore types at the same time. Potential Savings with Control Flotation control brings about savings or plant improvements in two areas; the first is in improved metallurgy and the second is in reagent savings. Improved metallurgy includes increases in the average plant recovery and achieves target concentrate grade level s more consistently. Average recovery increases between 1.0 and 5.0 percentage points have been widely reported (Paakkinen, 1979; Sutherland, 1984). Reagent savings of up to 40 percent have also been reported (Hales, 1985). VARIABLES OF IMPORTANCE Control led, Manipulated, and Disturbance Variables The initial step in the analysis of the flotation control problem is identification of important variables which can affect the efficiency of separation. The efficiency of separation is represented by a group of controlled variables which can quantify the performance of a flotation circuit. This group includes variables such as grade, recovery, tonnage through- put, and circulating loads. The efficiency of separation of a flotation circuit may generally be defined by a grade recovery map, where each point on this map re- presents a set of operating conditions (see Figure 1). However, the combination of operating conditions must be set to operate close to the economic optimum. The group of operating variables which are changed in order to achieve desired circuit performance are called manipulated variables and can be classified into two

Jan 1, 1986

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

By T. M. Gurr

In recent years the need for reducing energy costs has led many in search of alternative fuels, examples are gasohol, "cow power", oil shale, biomass, peat and many others. We have been involved with several peat resource evaluations and would like to share with you some of our observations and experiences. We hope our experiences may help you in your evaluation of existing or future projects where peat is considered as an energy resource. The items that we will cover are listed as follows: ? Peat Uses, Occurrences, and Characteristics ? Identifying Exploration Targets ? Peat Exploration ? Peat Prospecting and Reserves Analysis ? Peat Harvesting and Reclamation Assessments ? Summary and Conclusions

Jan 1, 1983

By Nathaniel Arbiter

The development of flotation machines since the first industrial use of the process can be divided into three stages. The first, up to about 1930, was marked by diversity in the means for contacting floatable mineral with the air/ water interface and for generating the interface, as well as in cell design. By 1927 Taggart (1) could list 170 patents covering flotation cells, and he mentioned dozens which were or had been in operation. He divided cells into eight categories according to design, type of separating interface, and where in the cell and how separation took place. These were: (1) Film or skin flotation with wet or dry oiling of surfaces; (2) pulp body process with bubbles generated chemically by pressure reduction, by vacuum or by boiling; (3) agitation-froth processes involving local supersaturation with air; (4) bubble column; (5) pneumatic; (6) cascade; (7) subaeration; and (8) combination and miscellaneous types and processes. Most widely used then were the agitation-froth, sub- aeration, pneumatic types. By 1943 a significant reduction in categories had occurred to the two main divisions of mechanical and pneumatic cells according to whether agitation and aeration were (a) by an impeller with or without compressed air, or (b) by compressed air alone. Cells at that time were still relatively small; the Morenci Concentrator completed in 1942 used 432 1.7m3 (60 cu ft) Fagergrens for roughing 45,000 and later up to 55,000 t/d.

Jan 1, 1979

By Levent Ozdemir

An extensive study involving laboratory testing and computer modeling has been performed to assess the technical and economic feasibility of utilizing the recently developed minidisc cutters on roadheaders for hard rock mining. The results show that heavy duty roadheaders fitted with minidiscs can excavate hard rock formations at acceptable production rates and cutter costs. This paper presents and discusses the results of this study together with the ongoing developmental efforts of this technology, which include laboratory testing of a roadheader cutting drum with minidiscs and full scale field testing of a machine in hard rock

Jan 1, 1995

A chartered bus with about 30 attendees of the just completed 1998 SME Annual Meeting headed toward Green Cove Springs, FL, which the author had been told was located somewhere south of Jacksonville, FL. In conjunction with the meeting in Orlando, RGC (USA) Mineral Sands provided a tour of its facility. The author had worked with heavy minerals on a laboratory scale, performing the usual gravity and magnetic separations, but had never been to a heavy mineral mine and processing facility. Years ago as a metallurgist, the author once applied for a job in a heavy mineral operation in Florida -it may have been the same operation. After turning north on to Highway 95, the endless billboards promoting beach-front retirement communities proved the Atlantic ocean was just a few miles away (although the author never caught a glimpse of it). After another hour, the bus suddenly turned west and continued inland for about 65 km (40 miles). The thought occurred, "We are talking about beach sands, what are we doing heading away from the ocean?" As the bus continued inland, the author was struck by the flatness of the land and by the lakes, rivers and wetlands. He was also impressed by the many fine stands of pine and hardwoods. The office of RGC (USA) Mineral Sands is located about 16 km (10 miles) south of Green Cove Springs. Upon leaving the bus, members of the tour were greeted by Graeme Sloan, general manager, and Elliot Mallard, manager of mining. They provided some general information about the operation, including a slide show. RGC's Florida operation produces four concentrates: zircon (ZrSiO,), rutile (TiO,), ilmenite (FeTiO,) and leucoxene (an alteration product of ilmenite containing 67% to 70% TiO,). With a work force of about 170, the annual production of the above products is about 23,27, 45 and 14 kt (25,000 30,000 50,000 and 15,000 st), respectively. RGC also has other mineral sand operations, in addition to gold and base metal mines, mostly in Australia.

Jan 1, 1998

By K. L. Bickel

Catalyzed diesel particulate filters (CDPFs) are used for reducing diesel particulate matter (DPM) concentrations in underground mines. The U.S. Bureau of Mines is conducting research on how catalyzed diesel particulate filters perform. Two CDPFs, with two different catalysts, are used on vehicles in two mines. The CDPFs are periodically removed from service and evaluated in the laboratory to determine their DPM collection efficiency, regeneration temperature, and effects on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions. This report summarizes the results of the laboratory evaluation, and the mines' experience with the CDPFs. Both CDPFs have operated over 2,000 h. One was evaluated after 1,646 h; its collection efficiency at one operating condition was 87.3 pct. After 2,135 h of operation it was removed from service because it was damaged. The second CDPF continues to be used after 2,328 h of service. The laboratory evaluation indicated its collection efficiency decreased after 1,584 h of use and its regeneration temperature increased from 405' C to 420' C. The mines' experiences with the two CDPFs varied. While being used on mine vehicles, both CDPFs became plugged with DPM on a number of occasions because of insufficient regeneration. CDPFs are capable of lowering DPM concentrations in diesel exhaust. They can also lower emissions of CO and HC, depending on the type of catalyst used. In this study, the performance of the CDPFs changed with use. Recommendations are given in this report for proper use of CDPFs in mines.

Jan 1, 1994

By W. Irwin

As a consequence of the oil crisis of the 70?s, the commercial value of coal increased very sharply and an upward trend in coal prices although now less pronounced, continues today. The graph shown in figure 1 illustrates the trend in the F.O.B. price of U.S. metallurgical coal. This trend occurs during a time when mechanized mining is firmly established as a means of production throughout the coal mining world. With modem methods of mining, mechanical cleaning is a necessity and quality control is no longer entirely dependant upon coal face practice. The efficiency of fine coal recovery is of vital economic importance to present day operations and good practice in this field contributes significantly to improving profitability. Numerous processes are available for the duty and this paper discusses one such system, namely the practice of froth flotation.

Jan 1, 1980

By A. Unal, H. Sevim

The utilization of high-sulfur Illinois coal by utility plants has been decreasing since the enactment of the 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal more attractive by offering the choice of taking the coal combustion and flue-gas desu furization products from the utility plants and placing them in the abandoned sections of their mines To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of product disposed of can be minimized In this paper, several such systems are presented The favorable operating conditions of each system are determined in terms of distance and tonnage ranges. For a 90 kt/year (100 thousand stpy) operation, it is found that, up to a distance of 150 km (93 miles), transporting products by truck would be less expensive than using rail cars and intermodal containers. Also, a case study is given in which a cost analysis is conducted for an underground coal mine receiving products from two Illinois utility plants. At 90 kt/year (100 thousand stpy) and a distance of 40 km (25 miles) between the power plant and the mine, it is found that truck transportation and under ground placement would cost $0.090/tkm ($0.131/st-mile) and $2.98/t ($2.70/ st), respectively.

Jan 1, 1999

By Jack Parker

Cycles of mine convergence coincide with annual cycles of temperature and humidity in the mine. Laboratory measurements confirm that the presence of moisture reduces rock strength and induces internal rock stress. Findings are used in the design of mine openings.

Jan 1, 1969

By P. Marcheselli, Jean-Yves Peron

A twin tube tunnel of 2 000 meters long and an internal diameter of 6.90 m has been excavated through alluvial ground, with low overburden, using a 8.0 m diameter Earth Pressure Balanced tunneling machine with foam injection and extruded concrete behind segment.

Jan 1, 1995

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988

By M. Tanaji

Over the last many decades, a significant amount of research has gone into the domain of slurry transport. However, design engineers still face many challenges with respect to prediction of pressure drop, critical velocity and other design parameters as a function of Solids % and Particle Size Distribution (PSD). The industry requirement is to transfer the slurry at the maximum concentration as possible (above 30% (volume %)) to make slurry transport more economically viable and to reduce water consumption. To facilitate the design and scale-up of slurry transport in pipelines and in process plants, there is a need for a correlation that can predict slurry pressure drops over a wide range of operating conditions and physical properties of different slurries. The objective of this study is to overcome the limited range of applicability and validity of existing correlations and to develop a generalized but more rigorous correlation applicable to a wider range of slurry sys-tems. The existing Wasp et al. (1977) method is based on multi-phase flow modeling approach. This study attempts to modify this approach by considering material-specific values of Durand?s equation co-efficient and by defining flow regimes based on particle Reynolds number. When compared with experimental data, the modified Wasp method proposed in this study predicts the pressure drop for slurry flows more accurately than other available correlations. Also, the pro-posed method requires minimal test/experimental data for a particular slurry system and can be extended over different input conditions. An iterative computer algorithm is developed to calculate the criti-cal settling velocity and pressure drop in a pipe as a function of Solids % and PSD. The solution method can easily be implemented in de-signing slurry pipes, design validation, and studying the different slurry transport scenarios. The modified method can also be extended to accurately predict pressure drops in dynamic pressure flow networks used in commercial process simulators.

Feb 23, 2014

By M. Karmis, C. Haycocks

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By Keith Whiting

The Van Stone zinc-lead mine is located in northeastern Washing- ton in Stevens County. It is about 24 km (15 miles) south of the Canadian border and 48 km (30 miles) west of the Idaho line. The deposits occur in late Cambrian age limestones and dolomites of the Metaline Formation. The bedding controls the trend of the zones containing the lenses of zinc-lead mineralization. The Van Stone property and vicinity is almost entirely covered with glacial drift averaging perhaps 6 m (20 ft) in thickness. Outcrops are very sparse. Outcropping gossan with zinc mineralization was first discovered by George Van Stone in 19 13, in what is now known as the South Ore Zone. Only minor trenching was done at that time. The property was idle until the mid- 1920s when Hecla Mining Co. drove several short adits and performed minor diamond drilling. In 1938, Willow Creek Mines of Nevada Inc. acquired the Van Stone plus adjacent parcels and commenced drilling on the known South Ore Zone. In the course of an expanded drilling program, the nonoutcropping North Ore Zone was discovered and was drilled out along a N30°E strike for about 305 m (1000 ft), beyond which point no mineralization was intersected.

Jan 1, 1991

By Clay Haynes, Tim Pearia, Robert Robinson, Judy Cochran

A 1.89 km-long, 4.5 m-I.D. tunnel was successfully constructed through saturated hard clay, and highly abrasive dense sand and gravel, with groundwater heads ranging from 10 to 20 m. In order to address these conditions, a Lovat earth pressure balance TBM was used, with soil conditioning by foam, water and various polymers. Support was provided by a single-pass segmented concrete lining. Groundwater inflows of 400to 1,600 lpm at times created challenges for changing cutting tools. Surface settlements were generally less than measurement thresholds, except under very low cover at startup. This project provides a pivotal case study of the successful application of EPBM technology in saturated, abrasive glacial soils and the successful application of soil conditioners.

Jan 1, 2003

By M. R. Lastra

Island Copper Mine began gold recovery Tom molybdenum sulfide concentrates in April, 1985. Plant design capacity is 20 tons of molybdenum concentrate per day. The molybdenum concentrate is produced in a conventional copper/molybdenum flotation circuit by selective copper depression. After thickening, the molybdenum concentrate is leached with cyanide solution in a series of five leaching tanks. The leached concentrate is then filtered and soluble gold values recovered on activated carbon with a six column adsorption circuit. The gold leach extraction is approximately 80 percent with a gold adsorption on activated carbon of 97 percent.

Jan 1, 1986

Early experiences suggested autogenous mills were difficult to operate and consumed substantially more energy than conventional rod/ball mill circuits. As our understanding has increased and the technology has matured this perception has changed to the point where most new comminution circuits are ag/sag based. In addition many operators have replaced existing conventional circuits with this technology. The JKMRC has been studying ag/sag mills for over 20 years. During this time it has amassed what is probably the single largest and most detailed data base of pilot and full scale mill operations in the world. This has been used to help develop and refine its cur- rent commercially available mathematical model of ag/sag mills. A decade of its application has greatly helped simplify both design and operation of ag/sag milling circuits as well as helping to promote the effective use of recycle crushing, secondary crushing and closed-circuit operation. This paper describes the development of ag and sag milling in terms of our understanding and the evolution of the technology. In addition the application of mathematical modelling and simulation in designing and operating efficient circuits is described with the aid of practical examples.

Jan 1, 1998