Search Documents

By John Hickey

Management teams at mining companies begin to ask themselves whether to take a company public and, if so, how to do it as they approach the normal threshold for going public in terms of revenue and operating performance. Today, the expense of going public generally suggests the company has at least $20 million in annual revenue and at least $2 million in cash. The revenue number can be lower for mining companies with large reserves. In order to properly attract the investing public, the company must also be operationally strong with robust prospects. The company should have a strong management team and a consistent history of double-digit growth that will continue into the foreseeable future. Assuming the thresholds are met, a company?s management needs to weigh the pros and cons of going public.

Jan 1, 2012

By Jamal Rostami, Tom Iseley, Saleh Behbahani

Tunnels and underground infrastructures assets, like all assets, deteriorate with time. At some point, they reach the end of their useful life. Therefore, frequent inspections, higher levels of maintenance, and rehabilitation are needed to address loss of life and safety concerns. The repair cost of tunnels will increase if maintenance of tunnels is not satisfactory and timely. Historically, tunnel inspections have primarily relied on visual and manual procedures. Due to their time-consuming nature and susceptibility to human error, there is a demand for alternative automated techniques that can enhance efficiency and reliability in tunnel inspection. By utilizing a tunnel scanning system, such as laser scanner and thermography, or photogrammetry system, tunnel inspection cost, time, and personnel can be reduced. The goal of this study is to utilize deep convolutional neural networks (CNNs) for automated identification of defects in tunnel lining inspection. This paper presents a framework to classify two types of defects in tunnel lining (water leakages and cracks) using CNNs. The CNNs were trained and tested using 4,608 images. The Precision, Recall, and F1 Score were each 99.6%, confirming the viability of this approach in the automated defect identification in tunnel lining.

Jun 23, 2024

By W. D. Diment

The concept of flying employees in and out of remote mine sites on a regular rotation basis, rather than establishing permanent support communities nearby, has gained increasing acceptance by mine operators, unions and regulatory agencies in Canada. The development of successful fly in/fly out programs and resultant compressed work schedules is dependent on meeting design requirements through comprehensive research of worker profiles to ensure the selection of suitable employees and the implementation of satisfactory working conditions. This paper presents an overview of Canadian mine industry practice with regard to the fly in/fly out mode of operation and compressed work schedules.

Jan 1, 1987

By L. F. Zeiler

In the past, health concerns in coal mines have primarily centered on those elements which have been essentially inherent to the mining environment. These would include respirable coal mine dust, respirable crystalline silica, excessive noise levels, and diesel exhaust particulates. Commercially-available chemical products are prevalent on mine property. These potentially toxic materials are chemical formulations that can degrease, clean, and lubricate metal parts, separate coal from rock in float/sink operations, and aid in roof consolidation, among other uses. As the general public has become more aware of the hazards of chemical exposures, miners have likewise become more concerned about working with an ever-expanding variety of chemical products on the job. Often, product or chemical specific hazard communication training is inadequate or ineffective, and miners do not know exactly what the ingredients are in the products they handle, or the health hazards involved with their use or misuse. Currently, the Mine Safety and Health Administration (MSHA), by law, enforces 1972 Threshold Limit Values (TLV). MSHA is making preparations to adopt new personal exposure limits for enforcement. The values given throughout the article are 1994 TLV's and are not enforcement standards, but are used for discussion purposes. They reflect the current scientific thinking regarding personal exposure to these chemical agents. An overview of these products is presented, and the potential health hazards associated with their use are discussed. Controls needed to prevent overexposures, such as proper handling procedures and personal protective equipment, are covered. Methods used to collect and identify contaminants are presented.

Jan 1, 1995

By Cynthia S. A. Wallace, Joseph E. Crawford

The Culberson ore body is a bioepigenetic sulfur deposit located in the Delaware basin. Sulfur occurs in the Upper Permian Castile, Salado and Rustler Formations. Most of the ore body forms a subhorizontal layer within the Salado Formation. Abundant cave fill deposits of Rustler and younger lithologies occur within the Salado Formation and predate mineralization. The cave fill deposits provided porosity zones within the otherwise impermeable sulfate host rock and controlled sites of mineralization. A northeast trending fracture zone near the west edge of the ore body localized some deep mineralization and may have allowed migration of hydrocarbons from depth.

Jan 1, 1992

By Melvin W. Kraschnewski

In 1966 Central Ohio Coal Company and Bucyrus-Erie signed a contract authorizing Bucyrus-Erie Company to design and build a 220 cubic yard dragline. This dragline would be used for stripping overburden from their coal reserves located near Cumberland, Ohio. The size of the machine was arrived at after a thorough application study of their annual coal output requirement, depth of overburden and type of terrain. The design and construction of this machine which has been designated by BECO as model number 4250-W is the title of this paper. Size wise based on machine weight the 4250-W represents an increase factor of three over our largest current dragline. Probably the easiest way of presenting a machine of this size is to build it from the bottom up.

Jan 1, 1969

By Eileen Ashworth

Introduction A study was completed that investigated the enrollment in mining engineering programs in 24 universities and colleges. All programs considered in the study award four-year bachelor of science degrees in mining engineering. They also provide all the engineers for the mining industry and a large portion of the geotechnical engineers working on environmental problems, storage of hazardous waste, civic, and Federal government underground projects. The numbers used as the base for the study are those reported by each program to SME-AIME and published yearly (SME, 1986). Data for the study came from the period 1975-1985. Also, since some programs include students in related disciplines and special categories, such as cooperative students, a few inaccuracies were unavoidable. A 23-page document has been prepared that reports on the overall picture of current enrollment, the trends, and discusses the results, perceived effects, and what can, or should, be done. There has been an obvious, and dramatic decrease in total undergraduate enrollment since the late 1970s. In 1978, 3117 students were enrolled. In the 1985 fall semester, enrollment was 1022, less than one-third. There were 485 seniors, 265 juniors, 147 sophomores, and 125 freshmen. The downward trend in total enrollment is likely to continue for at least another two years. Class size The catastrophic drop in enrollment is shared by all programs across the country. It does not discriminate between types of programs, coal or hard rock mining, or location. In general, 1985's enrollment is about 30% of whatever the maximum enrollment was in any program, though this varies from the teens to 50%. The latter percentage occurs only for some programs with special circumstances, particularly new programs not well established in the late 1970s. The beginning of the decline in enrollment has occurred at slightly different times as affected by the demise of each program's local industry. The numbers in each class produced from a specific freshmen year (Fig. 1) are worthy of comment. The dramatic drop in enrollment for all classes after 1982 is clearly demonstrated. The timing coincides with the general downturn in the mining industry, when many employed engineers were laid off and new graduates could not find jobs. Also, significantly fewer students are being attracted to mining programs as freshmen. The number of seniors shown seems inappropriate. Where did so many seniors come from and why are so few graduates produced? There is an increasing trend for students to take four-and-a-half or five years to graduate. Therefore, they are counted twice, once when they are first classed as seniors and again the following year. Some students purposely delay graduation to obtain more summer work experience and take additional courses. They believe that this gives them a better

Jan 8, 1986

By W. L. Cornell, F. W. Benn

The U.S. Bureau of Mines investigated froth flotation techniques to remove heavy metals (Pb, Cu, and Zn) from southeast Missouri lead mill tailings. It has been estimated that southeast Missouri contains between 200 and 300 million st of Pb tailings stored above ground. The tailings were classified as two distinct types: (1) pre- 1968 tailings from the Old Lead Belt (some more than 100 years old) and (2) post-1968 tailings from the New Lead Belt. The objectives of the investigation were to reduce the Pb remaining in the tailings to (500 ppm (<0.05% Pb) and to attempt to recover a marketable concentrate to offset a portion of the remediation costs. The remaining dolomite-limestone would then be used as mining backfill or agricultural limestone. Bench- scale froth flotation removed, in percent, 95 Pb, 84 Cu, and 54 Zn, leaving 94% of the original weight containing, in parts per million, 400 Pb, 40 Cu, and 300 Zn from the Old Lead Belt tailings. Separate flotation tests also removed, in percent, 85 Pb, 84 Cu, and 80 Zn, leaving 75% of the original weight containing, in parts per million, 400 Pb, 200 Cu, and 500 Zn from the New Lead Belt tailings . Concentrates recovered from the Old Lead Belt were retreated to produce a final Pb concentrate containing 72% Pb with a cleaner flotation recovery of 79%. Froth flotation proved to be a viable method to remove the heavy metals.

Jan 1, 1992

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-expanding push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source found in the USA is bastnaesite, a rare earth bearing fluorocarbonate mineral, currently mined at the Mountain Pass Mine in California. To increase production, it is essential to optimize existing processes and create new ones to better utilize current resources. Therefore, a US Department of Energy Critical Materials Institute sponsored research program was carried out at the Kroll Institute for Extractive Metallurgy to expand the fundamental understanding of the industrial bastnaesite concentrate leaching system. With the help of prior knowledge, thermodynamic calculations and design of experimentation based lab testing, a novel single-stage hydrochloric leach system was created to optimize the rare earth extraction from bastnaesite. Historically, the existing industrial process has utilized a two-stage leach system involving a high-temperature hydrochloric acid leach with liquid solid separations followed by a caustic crack stage of the leach residues. A series of single-stage leach experiments were run by reacting locked cycle flotation concentrates with hydrochloric acid to test common leaching parameters. The results of these patent pending single-stage tests have shown rare earth recoveries significantly higher than reported recoveries of historic two-stage caustic crack processes, all while decreasing the equipment required and the type and amount of reagents needed.

Jan 31, 2022

By Serguei A. Diatchkov

The principles of classification of reserves and resources in the Soviet Union were developed in 1960. Mineral reserve calculations were reviewed by the State Committee on Reserves for approval, then registered in the State List of Mineral Deposits and included in the State Balance of the Reserves. In 1981, however, a new "System of Classification of Reserves and Resources of Mineral Deposits" was adopted. This classification system (Table 1) is still used today in the Commonwealth of Independent States (CIS). It subdivides mineral concentrations into seven categories in three major groups, based on the level of exploration performed: explored reserves (A, B, C,), evaluated reserves (C) and prognostic resources (P1, P2, P3). Explored reserves Explored reserves are calculated within exploration contours. Category A The A category is the highest level of classification for any given mineral deposit and requires comprehensive exploration. First, the ore body&apos;s position, shape and structure must be accurately delineated (Fig. 1). Next, the mineralogy of the ore body must be studied to determine its composition and properties as well as the distribution of both ore and detrimental components. It is also necessary to outline the blocks of barren rocks and limits of subeconomic ores and to distinguish between the different types, grades and physical-chemical properties (mineral texture and structure) of the ore, the

Jan 1, 1994

By Jed H. (Original by) Mosgrove

Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 ma/s (9000 cfm) of air at his last open crosscut.

Jan 1, 1981

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By David Morrison

"The history of the mining industry is littered with in-pit crushing and conveying (IPCC), which should not be confused with the International Protocol for Carbon Capture, projects that failed. The failure is not the technical one of “did it achieve the desired tonnage rate for a longish test period” but, rather, the far more important one of “did it provide return on the investment in the manner that was promised?” While quite a few can claim the former, very few system installations can claim the latter.The reasons for the many failures are numerous, but they are all characterized by a combination of an element of engineering optimism in any, or all of the production rates, the productivity, or the operating and maintenance costs and in predicting the continuity of operating conditions. In these days of big data, propagating such a situation is rapidly becoming unforgivable.In this article, the three most common scenarios put to the corporate board for approval, and the logic as to why they were selected, are examined (with the irony included intentionally).• Fully mobile crusher, fed by a shovel and conveyed out of the pit to a waste dump / process plant.• Semimobile crusher (much more expensive than a fixed crushing station but which apparently allows trucks to short haul inside the pit and improve productivity), which moves when the face moves.• Relocatable crusher (more expensive than a fixed crushing station but which gets relocated at great expense after all the fixed infrastructure impeding relocation is demolished) fed by trucks that don’t leave the pit mostly.This paper will also consider the truth about their operational performance and associate costs."

Dec 1, 2016

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey&apos;s Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975

By G. Papantonopoulos

Natural stones are extensively used for construction purposes since the dawn of human civilization, due to their unique aesthetical and technical characteristics. Their production and consumption has been continuously increasing over the past twenty years worldwide at an annual rate of 8.8%. European countries lead the race of per capita consumption, with Switzerland being in the first place with a consumption of 144.7 m2 per hundred inhabitants followed by Greece, Spain, Portugal, Belgium and Italy. On the other hand, during the period 2001-2002 the generated stone wastes were 110 million tones according to EU data, from which only about 5 million tones were recycled or re-used mainly in the construction industry. These stone wastes the non-natural wastes such as oils or chemicals coming from the equipment and machinery employed for stone extraction and processing, are disposed in the environment, posing serious environmental threat. To achieve sustainable development of the stone sector appropriate methods that will prevent or reduce waste generation and disposal have to be identified and applied. In this work an extensive study of the stone waste management techniques applied in Europe is carried out, in order to identify the Best Available Techniques (BAT) that can be used according to the type of generated wastes and the waste management hierarchy: Waste minimisation, Re-use, Recycling and Disposal. The identification of BAT was performed based on 14 Sustainable Development Indicators (SDI), which were grouped into three categories: environmental, economic and social. The developed final list of BAT includes waste minimisation techniques, eco-management schemes, in-situ treatment and appropriate storage and selection.

Jan 1, 2007

By EDER DOMINGOS OLIVEIRA, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

Special attention must be considered in the production of high-grade rare earth products, such as mixed rare earth oxalates or carbonates. In the main minerals used industrially, the rare earth elements (REEs) are finely associated with impurities like calcium (Ca), magnesium (Mg), manganese (Mn), iron (Fe), aluminum (Al), thorium (Th), uranium (U) and phosphorus (P). Most of these impurities must be removed to avoid losses of rare earth oxides (REOs) as well as to prevent product quality degradation and low operational performance in the downstream steps of solvent extraction or ion exchange. The present study aims at investigating the conditions required to precipitate REEs, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with low Al3+ and UO22+ concentrations and very high Ca2+, Mg2+, Mn2+, and SO42− impurity contents.

By John V. Beall

A completed feasibility study executed by an independent agency can benefit a company in two ways. Inside the organization, it verifies the project staffs ideas and their concept of the facility. Outside the company, it can be utilized to obtain equity partners, debt financing, and other forms of credit. It is advisable to bring in a project execution contractor for the feasibility study. A project execution contractor is able to work with engineers to develop the project concept, process flowsheet, and best utilization of the site. By getting an early start on understanding a company&apos;s policies and working methods, a project execution contractor saves the company money since it does not have to go through the educational buildup twice. The contractor is a specialist in putting together a bankable document that can be taken to a financing source. It answers all the agency requirements on the first pass. In addition, the contractor can advise an owner on likely financing sources since he works on the worldwide market every day. A less obvious advantage of including the contractor in the study and predevelopment buildup stages is the importance of coordinating finance and technical input. The financing source influences equipment specifications, procurement, logistics, project schedule, cash flow, and liquidity. There are many surprises in store for any manager of a large international project involving worldwide financing and purchasing. The job does not have to be made more difficult by bringing in a contractor after all predevelopment steps are taken. The contractor can still work if the predevelopment steps have been done, even if he does not agree with them. But early contractor involvement is the preferable solution.

Jan 10, 1980

By T. W. Camm

"We hear all the time about the value of hard work and perseverance, and the part they play in the professional life of successful people. What we do not hear so much about are the many professionals who work hard and persevere, yet never seem to quite reach the level of success they aim for. Some current authors are beginning to give more attention to the part luck/black swans/outliers play in success. This is not a new phenomenon, Machiavelli had a lot to say about it back in the Renaissance. So how can knowledge of this dynamic help in a modern organization? INTRODUCTION Work hard and you will succeed. Go to the right school, major in the right degree, study hard, and get a good job. Look at the lives of successful people, and do what they do. Be all that you can be. You can be anything you want to be. Really? Those who are successful always get attention, people want to know what they did to reach such a high position. Invariably, at least part of their narrative will include hard work, wise insight, taking advantage of opportunities, etc. If they are of a more generous nature, they might also allow that building the right friendships and collaborations also played a role. All of this may be true; what we do not often hear are the stories of those who did all of these very same things, but did not find success. An example from pop culture: The Voice. I have watched this show occasionally the past couple of years. One of the things I like about the show is that the initial screening of contestants is based solely on their singing voice (hence the name of the show), and not on their appearance. At the time of this writing (early November), the judges have just finished elimination rounds for their final teams to go on to the live shows. Here is my point—in almost every case the judges agonized over choosing who would go forward and who would be eliminated. And the reason is because all of them are really talented singers. It is impressive how gifted they are. At the end of each season, only one is declared a winner, out of that gifted pool of singers. When you hear their stories, they are all talented, hard-working individuals sacrificing for their art. And as far as I know, none of them has ever become a star. Hard work, dedication, sacrifice, talent—sometimes it is enough, sometimes not. I will be looking at the part uncertainty/luck/black swans play in our lives, but I want to make it clear at the beginning that I am not saying everything that happens to us is out of our hands or beyond our control. Taleb makes this same point (2007, p. 52): “This problem is chronic: if you tell people that the key to success is not always skills, they think that you are telling them that it is never skills, always luck.”"

Jan 1, 2017

By John C. Galloway, Heinz G. Leistner

ACKNOWLEDGEMENTS The investigations described in this paper were supported by contracts with the Defense Nuclear Agency (DNA) under direction of Lt. Col. John Galloway, and by Boeing Company research funds under supervision of James Wooster. Other engineers of The Boeing Company who contributed to the work of this investigation were Don Armitstead, John McAvoy, and Tom Day. INTRODUCTION In this paper, we are describing a current concept for placing intercontinental ballistic missiles (ICBMs) in sites deep underground to be used as a strategic Future Secure Reserve Force (FSRF). The objective of such concepts is to utilize soil and rock cover to protect high value strategic weapons from destruction by nuclear attack. The burial deep underground achieves two purposes. First, it imposes a miss distance upon the attacking weapon equal to the depth of burial minus any penetration capability the weapon might have. This tends to offset increasing accuracy of weapon delivery. The other purpose is to absorb as much of the weapon&apos;s energy as possible, thus reducing the effects of powerful weapons. This use of soil or rock cover over military facilities began with the development of man&apos;s capability to loft projectiles. Until recently, underground military installations, by their nature, performed defensive functions. Since they are not mobile and their weapons in the past had very limited range, an enemy would have to approach them before an engagement could take place. Thus, they were often used to control "choke points" on sea lanes as in the case of Gibraltar or

Jan 1, 1979

By Jerry W. Danni, John E. Hardaway

Corporations today must comply with an ever growing number of complex and increasingly stringent environmental laws and regulations. An environmental audit program is an effective means in which to uniformly and systematically assess compliance, and to assure management that environmental liabilities are being minimized. This paper describes the design and implementation of Homestake Mining Company&apos;s environmental audit program, which has as its primary focus the objective verification of compliance with external requirements and internal good management practices. Major elements of the audit program discussed in the paper include: pre-audit preparation; on-site audit activities; and the post-audit report.

Jan 1, 1992