Search Documents

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By Jerry D. St. Clair

A multidisciplinary team of scientists and engineers at Wont has been working to understand heavy metal contamination of DuPont process waste streams and technologies for abatement of these metals. As part of this effort, an extensive study was made of a specific waste stream of importance in DuPont's environmental commitment. This 200 gpm stream contains 5-5000 ppm of nickel plus a variety of inorganic and organic constituents. The chemical complexity of the waste rendered conventional. alkaline precipitation ineffective, and only through the simultaneous application of analytical characterization, fundamental chemical understanding, and process engineering did effective technical approaches emerge. In this instance, ion exchange, sulfide precipitation, and caustic digestion ultimately proved successful in reducing the nickel to below the 1 ppm target. The results of this study will be presented, along with key learnings about the process of solving heavy metal contamination problems.

Jan 1, 1994

By Kiyoshi Shibata

A new assessment model has been proposed for metal production and its recycling system. The model consists of three processes, smelting of ore, cascading and upgrading of metal scrap. The present approach is to assess the total energy consumption of the system, by introducing two equations for describing the relationships between critical impurity content and the mass of production or scrap recycling. The total energy consumption in the system can be described as a function of recycling rate and performance of the upgrading process. The present model suggests that the impurity removal efficiency and yield in the upgrading process are essential to reduce the energy consumption in the systems. Especially, such points should be explicitly controlled in recycling of aluminum. The potential capability of this model was also discussed by obtaining several quantitative information required for the process design and the operational control of beneficial recycling of metals.

Jan 1, 1998

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By R. Hammen

Processes are needed to rapidly and cost-effectively produce highly pure lithium salts for the rechargeable battery sector. Lithium purification is a chemical engineering challenge, due to the low concentration of lithium compared to sodium, potassium, magnesium, calcium, and transition metal ions commonly occurring in lithium brine resources. We describe a Solid Phase Extraction (SPE) process that rejects sodium and potassium, while binding lithium and other higher valent ions. Lithium is then harvested by selective displacement from the SPE column. The rapid equilibration kinetics of SPE composites enables these ion separations to occur in a small SPE column and in one column stage. The chemical parameters of the process are described.

By Alvear G. R. F. Flores

It is now 35 years since the organization of the first sulfide smelting conference in 1983. Since then, the smelting base metals industry has experienced several changes driven by the necessity to improve economic, operational and environmental performances and resource efficiency and meet the increasing market demand for metals. In this continuously challenging environment, it is relevant to recognize which are the main challenges that the industry will face in the coming years and critically address our preparedness to respond to them. This analysis have to consider not only the effort required from the fundamental research and technology aspects but also how these pillars interact with the drivers behind the base metals industry. This paper discusses some relevant aspects required to continue developing the base metal industry focusing on copper. Aspects such as the need to supporting the generation of fundamental metallurgical knowledge, acquisition and proper use of data with advanced analytics methods, technological innovation to develop sustainable process flowsheet are discussed with emphasis on efforts conducted by Aurubis.

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By M. Elbert Nigri

Radioactive wastewaters from nuclear source of electrical energy production need to be treated and disposed of properly. Sr, Ca, Mg and Ba are common elements in this effluent, which can cause incrustation in process equipments and being unsafe to human health (90Sr). Fixation of CO2 can be applied to remove the ions mentioned before and to provide a solution where CO2 is sequestered and the deleterious elements precipitated, becoming one of the possible steps to reuse the water into the process. Moreover, removal of several metals from distinct wastewater has been evaluated using bone char through adsorption. The chemical similarity between calcium and strontium makes the exchange of these two metals favorable in the hydroxyapatite structure contained in bone char. This paper evaluated the combined action of precipitation and adsorption process with injection of CO2 and bone char addition in simulated nuclear wastewater. Removal levels of 89.0% (Sr) and 83.3% (Ca) were obtained in the combined process. The presence of bone char as seed increased the precipitation kinetics, allowing a Sr removal of 85.2% in five minutes, higher than 75.3% obtained in absence of seeds. However, removal of 91.6% (Sr) and 89.8% (Ca) were obtained in absence of seeds at 24 h. Analysis of solids have evidenced that CO2 was consumed to precipitate the metals as carbonates, since the hydroxides are formed at higher pH’s.

By Jacques J. Eksteen

Any effort to improve the metallurgical control of industrial furnaces employed in the primary extraction of high carbon ferroalloys are bound to fail unless the variability of the melt is not fully accounted for. A number of sampling campaigns were performed on both 3phase AC submerged arc and single phase DC open arc furnaces at different smelter sites in South Africa where High Carbon Ferrochrome is produced. It was found that the heterogeneity between multiple samples during a single taps were much higher that for heterogeneity found within a sample. Moreover, this heterogeneity (as quantified by the relative standard deviation per tap) varied with the operating conditions of the furnace, the element monitored and the type of furnace. A relationship was found between the relative standard deviation of certain elements and the degree of subcooling of the melt.

Jan 1, 2006

By C. E. M. Meskers

Electronic and Electric Equipment contains a range of components made of a wide variation of metals, plastics and other substances. Up to 60 elements can be found in complex electronic equipment: base metals, precious metals and special metals in circuit boards and batteries. Because of its amount WEEE represents a considerable metal resource with a higher special and precious metal content than found in ores. The Umicore integrated smelter and refinery recovers and supplies back to the market 17 different metals from EEE. Pre-treated materials enter state of the art, material and energy efficient metallurgical processes for environmentally sound recovery of metals and treatment of off gasses and hazardous substances. The organics in the feed function as reducing agent and alternative energy source during smelting for precious metal recovery. Lithium-ion batteries are treated using a dedicated process. As a result the environmental footprint of metals produced from EEE is much smaller than primary production.

Jan 1, 2009

By Paul-Dominique Oudenne

For many years, CMI NESA has gained considerable experience in the field of alternative thermal processing processes by which useful by products result in addition to the destruction of the raw wastes. The CMI NESA pyrolysis process has been extensively applied to a wide range of sewage, industrial sludge and residues. This paper describes in details the development works carried out at the pilot stage as well as the key parameters of the process. Some of the industrial realisations are briefly described, the most recent one being the erection of a sludge pyrolyser on predried sludge at 90% dryness of a capacity of 100 tons of dry matter per day for the Valenton plant of the SIAAP (city of Paris).

Jan 1, 2006

By Zhang Chuanfu

Keywords: solid solution, Ni-Co alloy powders, thermal decomposition, fibres. Synthesis of fibrous Ni-Co alloy powders was achieved by thermal decomposition of precursor of complex Ni-Co oxalates solid solutions obtained via modified coprecipitation method among intimate mixing solution of NiCl2?6H2O , CoCl2?6H2O and H2C2O4?2H2O in the presence of surfactant polyvinylpyrrolidone (PVP) and organic solvent ethanol. Scan electron microscopy (SEM), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), disperse energy X-ray analyses (EDX) were used to characterize the structure features and chemical compositions of the as-prepared fibres. The influences of decomposition conditions, including temperature, time, the flow rate of N2+H2, and the heating rate, on the morphology, average size and specific surface area of the Ni-Co alloy powders were investigated. It is found that a trend of the mutual alloying of nickel and cobalt: the formation of perfect solid solution for any compositions NixCo100-x was indicated and corresponding NixCo100-x alloys with fcc phase can be obtained under the optimal conditions.

Jan 1, 2005

By A. Kontopoulos

The Olympias Mine in Northern Greece is producing an extremely refractory gold-bearing arsenical pyrite concentrate, containing on the average 41 3 S, 40 3 Fe, 10-12 3 As, 25 ppm Au and 35 ppm Ag. During the process selection stage, more than a dozen alternative technologies? were considered and an in-depth analysis was prepared for the three most promising, ie roasting, pressure oxidation and biological oxidation. Detailed capital and operating cost estimates were prepared, based, where appropriate, on laboratory and pilot-plant tests. A number of criteria was used for process evaluation and selection, including capital and operating costs; environmental impact, gold' recovery, stage of development, etc. Based on the above evaluation, the Sherritt Pressure Oxidation Process was finally selected. A detailed description of the process selection stage, supported with laboratory and pilot-plant test results on many of the processes considered, will be? presented.

Jan 1, 1989

By Kazuteru Tozawa

Surface tension, density and viscosity coefficient of acidic copper sulfate solutions simulating electrolyte solution for electrolytic production of copper have been measured and are summarized as a function of the solution composition and temperature. Nickel sulfatc is taken to be a representative coexisting sulfate that affects the physical properties of the copper sulfate electrolyte solution. The sulfates in the solutions, including sulfuric acid, increase the physical properties under consideration. Gelatin, representing organic additives for electrolyte solution, was found to sensitively affect the surface tension of the solution at low concentration of up to 200mgIL. The surface tension was markedly lowered by the addition of gelatin and the increasing concentration of gelatin led to a more pronounced decrease in the observed values. The surface tension gradually increases with time after addition of gelatin and the increase is enhanced by higher acid concentration and higher temperature. The observed change in the surface tension is considered to reflect the preferential adsorption of gelatin to the bubble-solution interface and the decomposition of gelatin due to hydrolysis to form various molecules having smaller molecular weights.

Jan 1, 2003

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996

By Orlando C. Gaspar

The textures of the ores, the fine mineral intergrowths, the complex distribution of the deleterious minor elements, and the low base metal contents in some ore types, pose many technological problems to the beneficiation of the volcanogenic massive sulphides occurring in the Iberian Pyrite Belt. In particular fine intergrowths of the base metal sulphides with pyrite impose extremely fine liberation sizes (Kao=15 to 25um). The mineralogical, textural and metallogenic studies have provided an understanding of the distribution of vertical and lateral metal zoning in the ore bodies. Mapping of the ore types, carried out by mine geologists, and the metal zoning patterns computed from data base have shown that ore types are distributed as ore lenses, and that vertical and lateral base metal zoning exists in several orebodies. Since ore processing efficiency is affected by ore textures, and because the same mineral often shows different textural features, a relationship between the textures of the feed ores and those of the middlings must be established for all ore types defined at the deposit scale. For supplying, on time, the information needed for the optimization of the concentration processes, empirical methods of determining the mineralogical and textural characteristics of the several ore types have been developed.

Jan 1, 1995

By Walter Curlook

An atmospheric acid leaching process for leaching nickel and cobalt from highly-serpentinized saprolitic fractions of nickel laterite deposits has been developed and patented [I]. The process involves leaching the highly-serpentinized saprolitic portion of the nickel laterite ore profile in strong sulphuric acid solutions at atmospheric pressure and temperatures between 80°C and 100°C, essentially autogenously, to extract over 85% of its contained nickel content and a large proportion of its cobalt content after leaching times of about one hour. The amount of sulphuric acid used in the leaching process is between 80% and 100% by weight of the finely ground highly-serpentinized saprolite ore on a dry weight basis. The metal values are recovered as intermediate products. Key words: Atmospheric Leaching; Nickel Oxide Ores; Laterites

Jan 1, 2004

By D. W. Lawler

Prior to the manufacture of sulphuric acid in metallurgical plants, the SO2 rich gas from the smelter, roaster, or furnace must be cleaned to removed particulates, volatile contaminants, SO3, and water. Cleaning is accomplished by contacting the. gas with cooled weak acid. The system is designed so that all the contaminants, originally in the gas are captured in the weak acid, which then becomes an effluent from the plant. Historically, the entire weak acid effluent stream has been treated for disposal, with no attempt to recycle or recover any part if it. This is becoming increasingly environmentally unacceptable, and operators must consider better methods of treatment and recovery. In this paper, Kvaerner Chemetics discuss a number of options that allow the contaminants to 'be separated from the acid' value. This will result in an acid byproduct that can be sold or used elsewhere, and will minimize the volume of hazardous byproducts that must be discharged.

Jan 1, 1998

By Chang Chia -Fu

The generic structure of our bimesogens is shown in and for a typical blue-phase mixture of the type we describe here. We use mixtures of the ratio 33.4% (n =2.6), 34.1% (n =6.57), 36.6% (n= 11.15) with of the high twisted power (HTP) agent BD H1381(available from Merck Chemicals and described in ref. We then studied the electric-field dependency of the selective reflection in BP I* at 20.7 °C by applying increasing and the decreasing pulsed alternating current (a.c.) electric fields (100 Hz).

Jan 1, 2006