Search Documents

By Dong-mei Zhang, Feng Zhang, Hong-Wei Huang, Qiang Huang, Bin Ye

"1. INTRODUCTION Nowadays, many cities around the world have constructed metro tunnels to alleviate transportation pressure from rapid urbanization. In soft soil areas, metro tunnels are usually constructed by shield-tunneling method due to its high efficiency and little disturbance to environment. However, the tunnels may show significant post-construction settlement after several years of operation. Take Shanghai Metro line 2 for example, the maximum longitudinal settlement reached 160mm after ten years of operation, shown in Figure 1. When analyzing varying factors that contribute to the long-term settlement of tunnels, the effect of cyclic loading from train vibration is rarely taken into consideration for most researches only focus on the influence of leakage problems in the tunnel while neglecting train vibration induced leakage and resulting settlement. It’s true that metro tunnels from shield-tunneling method are prone to have leakage problems due to the special structural configuration. Furthermore, trains move hundreds of times inside the tunnel every day, which inevitably will cause accumulation and dissipation of excess pore pressure. When the excess pore pressure dissipates, tunnel settlement induced by train vibration occurs(Deng F H, 2007). Although researchers (Zheng et al., 2005; Wongsaroj et al., 2007; Mair, 2008; Shin et al., 2012; Zhang et al., 2012, 2015) conducted extensive numerical analysis on the relationship between tunnel settlement and relative permeability of tunnel to surrounding soil by treating tunnels as permeable media, their attention was only paid to the tunnel settlement from reduction of hydrostatic pressure in the ground, rather than from the dissipation of excess pore pressure generated by train vibration. Therefore, the influence of train vibration on the long-term settlements of metro tunnels is still not clear."

Jan 1, 2016

By Frank F. Aplan

Froth flotation has been used to improve the recovery of fine coal, for minimizing the sulfur and ash content of clean coal and for the removal of fine coal from recycled or discharged backwater from coal preparation plants. Though froth flotation and allied processes for ores date from the turn of the century, with the first U.S. commercial application in 1911, coal flotation has been introduced into U.S. practice much more slowly. The first European coal flotation plant was started in 1920, and by 1933 Europe had 60 operating plants while the United States had only one plant, newly commissioned. Over the years there has been a steady increase in coal flotation so that today one-third of the 345 U.S. plants employ the process. This report traces U.S. coal flotation practice and technological improvements from early laboratory experiments in 1915 up to today's extensive use of the process.

Jan 1, 1999

A linear programming model with integer sequencing variables is developed to schedule limestone production for a quarry in Central Japan. The model is used to optimize raw material production from the quarry supplying limestone to cement, quick lime and aggregate plants. Typically, the mining in the quarry takes place in four to six different areas each area having 3 or 4 mining increments. Each mining increment contains different quality of limestone. The limestone production from the quarry is transported to the plants byway of 3 ore passes. Each plant requires a given quantity of limestone per period meeting certain quality constraints. This paper will describe development of the scheduling optimization model and how it is used to schedule production by period within the quarry to meet the capacity and blending requirements of the plants.

Jan 1, 2003

By Arun Patel, Diane Hirsch, Pamela Moran

The Metropolitan Washington Airports Authority (Authority) has undertaken a tremendous expansion of Washington Dulles International Airport in Fairfax, Virginia, including upgrading passenger transportation between concourses. The first stage of this expansion envisioned a shallow cut-and-cover pedestrian tunnel between the Main Terminal and Concourse B with associated vertical circulation structures. At the beginning of the design contract, the Authority’s consulting team of Earth Tech, formerly Kaiser Engineers, and the Dr. G. Sauer Corporation compared the cost and disruption of constructing the tunnel as a cut-and-cover structure to mining the tunnel using the New Austrian Tunneling Method (NATM). Upon review, the Authority endorsed the latter method.

Jan 1, 2003

By G. Yang, M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya

In the last 20 years, studies on controlled flow recirculation in various countries have been carried out in both coal and metal mines. These studies have shown that in addition to economic gains, partial flow recirculation can be used to provide mine workings distant from surface access points with the required volumes of air. These studies have also shown that the operation of fans and regulators, used in a recirculation system, will induce transients in gas flow and gas concentration. Various models have been developed to explain the problem. However, most have failed to incorporate important factors such as diffusion and dispersion in the modeling process. This study examines the theoretical background of gas emission transients from caved areas in coal mines, represents the problem by a "tank-airway" network model, and provides a possible solution. The study also presents the results gained from a laboratory model constructed to evaluate the major factors affecting the shape and duration of gas flow and gas concentration transients in an airflow recirculation system. In this model, the gas injection system was rearranged to simulate the variations in gas emission rates due to changes in air pressure. Within this model, a set of booster fans and regulators were used to generate the changes in air pressure within the model. Finally, the study presents an algorithm and a computer program GASTRAN, developed to analyze the gas concentration transients and calculate the pollutant transport levels in a complex ventilation network. The application of the program is illustrated by means of an example problem.

Jan 1, 1991

Currently the challenge that our society faces is to combine the economic activity for the continuously increasing needs of our expanding population with the necessary environmental integrity and the humanistic social concerns. In this paper, the methodologies that should be applied by the progressive mining industry in order to fall within the frame of the sustainable development are summarized. The Sappes project, an advanced gold mining project in north-eastern Greece, is presented together with the approaches adopted by Thrace Minerals S.A.

Jan 1, 2003

By L. A. Puchkov

Problems of how to use artificial intelligence (AI) methods and expert systems (ES) to control complex industrial projects have lately become significant in practical terms. Mining ventilation systems undoubtedly belong to complex multi dimensional objects of control with stochastic nonstationary and nonlinear processes. Formal models based on automated ventilation control, do require awkward algorithmic solutions, moreover, a number of tasks become the operator's headache, and the quality of their solution depends on his experience and intuition. These tasks include: - identifying pre-accidental situations and determining their causes; - making well-grounded decisions with regard to changing ventilation regimes, forecast of mining operations taken account of; - controlling ventilation systems in emergency situations, e.g. when in accident, etc. It is in this context that we have for a number of years been investigating how to practically use AI methods for operative control in dynamic aero-and-gas mining processes, one of our research directions being devoted to working out a consulting programme for the ventilation system operator. Our researching and modeling problem was identification of aero-and-gas situation in different parts of ventilation network and its interpretation in order to determine possible causes for gas regime changing and unexpected consequences. We would single out the following stages in this task: I. Operative information procession coming to the data base from the sensors and analysis of hypothetical versions (using the associative rules base) with regard to factors which have caused significant parameter fluctuations (e.g. C%(t), H(t), Q(t) etc.)., 2. Selection of hypotheses in the knowledge base and forming conclusions in accordance with reliability scale. 3. Clarifying the obtained conclusions in dialogue with the operator. 4. Correcting the associative rules base.

Jan 1, 1992

By Hans von Michaelis

Gold metallurgy has advanced remarkably over the last decade. Even more significant progress will be made over the next five years, particularly in the application of advanced comminution techniques and control, preconcentration (flotation, ore sorting and coal gold agglomeration), enhancement of cyanide leaching technology, non- cyanide leaching, treatment of refractory ores and concentrates, and improved recovery systems. Carbon adsorption processes have become standard practice for ores with relatively high gold/silver ratios, but ion exchange potentially offers distinct advantages and has recently been demonstrated to perform better in at least one application. Even in the established zinc precipitation and CIP processes several important practical improvements are emerging as experience is gained at the ever increasing number of operating plants. Improved process control and reduction of reagent consumption costs are two important goals of industry at this time.

Jan 1, 1989

By J. Stachulak

This paper deals with theoretical considerations and practical applications of ventilation network calculations, based on mass flow rates and performed by computer simulation in our deepest operating mine - Creighton. The paper also deals with natural ventilation. In the usually accepted air-flow theory, the air is assumed to behave like an incompresssible medium. This introduces considerable error where temperature and pressure changes are great. Therefore, any study of the air flow in deep mines, must take into account compressibility. Basing ventilation calculations on mass flow allows a distinction to be made between air leakage and such quantity changes which occur due to air density changes. The energy which is required to convey one pound of air through a mine can be obtained by adding all head losses hL (ft-lb) of the ventilation paths through which the air flows. However, this total energy will not be correctly expressed in a compressible fluid by summing all pressure losses PL = hL x d (ft-lb/ft3 = lb/ft2) d = density. There is a law of mass conservation, but no law of volume conservation. Natural ventilation is caused by the conversion of heat into mechanical energy and not by the difference in upcast and downcast densities, as often believed. In an existing mine natural ventilation can be determined correctly by plotting a pressure volume diagram and measuring the area ? [ ] vdP = hN, where v = specific volume, or by measuring the sum of all friction losses and work provided by a fan. These procedures are tedious. The natural ventilation head (hN) can be approximated by the equaticn hN =[ ] tdZ. Where T is the average absolute temperature, t air temperature and Z elevation. In Prof. R. Greuer's computer program this determination of hN is automatically done for every mesh of the network.

Jan 1, 1980

By Ted H. Eyde

Specialty sand and bentonite are produced in the plateau province from the Bidahochi Formation near Sanders, Apache County, Arizona. It appears that deposits of both sand and bentonite formed during the Pliocene in fluvial and lacustrine environments, respectively, along the west side of the Defiance Uplift. The bentonite is an alteration product of airborne vitric ash that fell or was washed into lakes. In the Cheto district, the individual bentonite horizons, which range from less than a foot to more than 10 feet thick, are restricted to the position of the medial volcanic member. Bentonite production began at the Allentown mine in 1924 and the Chambers mine in 1926. In 1933 strip mining of the extensive deposits in the Cheto district commenced. Production increased each year to a peak of 270,000 tons in 1957. As a result of the introduction of synthetic zeolites into petroleum refining, production declined. About 40,000 tons of bentonite are currently produced from the district each year. Bentonite is shipped out of State for processing into desiccants, thickeners, and acid-activated clay products. The specialty sand was derived from Permian sandstones and deposited by streams draining the Defiance Uplift. Although stream channels are usually restricted to the upper member of the Bidahochi, stratigraphically above the bentonite horizon, a few actually cut through the bentonite. The well-sorted sand, suitable for use as a proppant in hydraulically fractured oil and gas wells, is localized in elongate lenses along the margins of the channels. These lenses range from 5 to 50 feet in thickness and often extend thousands of feet in both width and length. The sand is about 97 percent silica, has a yield of 40 percent in the minus 20 plus 40 mesh size fraction, and has a roundness of 0.6 to 0.7 on the Krumbein scale. Production of this sand began about 1961. All of the current production, which amounts to about 40,000 tons per year, is sold in the petroleum-producing area near Farmington, New Mexico.

Jan 1, 1987

By D. A. Norrgran, J. N. Orlich

Described is the application of high- intensity magnetic separation throughout the spectrum of industrial minerals. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents. The various types of magnetic separators along with the design and operating parameters relative to separation response are characterized. The characteristics of specific minerals to magnetic collection and the production of high-grade concentrates are described. Laboratory, pilot-scale, and plant studies carried out on a variety of industrial minerals have demonstrated the effectiveness of magnetic separation as either a primary or a secondary unit operation to achieve product quality.

Jan 1, 1987

By Dennis C. Drehmel

Because of their relatively low cost, carbonate rocks are desirable in abatement of air pollution by acid gases. Although many processes and types of equipment have been proposed to control or prevent the emission of acid gases, this paper considers only three: dry-limestone injection, wet-limestone scrubbing, and chemically active fluid beds. For the dry-limestone-injection process, surface area-especially from pores in the 0. 2- to 0.3-micron range-is one of the important parameters which will discriminate between less and more reactive carbonate rocks. Marls, chalks, oolitic calcites, and other fine- grained limestones show larger-than-average surface areas and better- than-average removal efficiencies. Inert chemical impurities such as silica detract from reactivity. A dolomite is not necessarily less re- active than a calcite. For the wet-limestone-scrubbing process, dissolution rate of the carbonate rock controls the differences in stone reactivity. In this process the dolomites are less reactive than the calcites. In addition, more than 90 percent of the dolomitic impurity in Fredonia white lime- stone is inert during limestone scrubbing. Dissolution rate is also a function of particle size for large-grained carbonate rocks. Fine grinding of such rocks will increase the dissolution rate to that of a fine-grained rock. Hence the requirement of high dissolution rates may be met by some grinding of fine-grained material (e. g., marl, chalk, or other limestone) or by fine grinding of coarser grained material. For chemically active fluid beds, chalks have the best capacity to absorb both SO2 and H2S. However, most chalks are probably unsuitable for fluid beds because of high attrition rates. Because dolomites are generally more reactive than calcites with both SO2 and H2S, a dolomite would be the feed material of choice for a chemically active fluid bed.

Jan 1, 1974

By Faruk Oksuz, Clay Haynes, David Egger

The United States Army Corps of Engineers (USACE) has committed to solve a major drainage problem in the suburban Chicago community of Griffith, Indiana. The Cady Marsh Ditch is currently undersized and on occasion spills its banks causing flooding and economic setbacks to the community. Preliminary studies have identified both tunnel and surface solutions as being attractive and viable. The USACE has decided that this project is an opportunity to use the design-build contracting approach to maximize ingenuity in project approach and to allow the market to dictate whether a surface or subsurface solution is most attractive. The tunnel would be over one-mile in length through sands, gravels and clay. Water control will be an issue during tunneling. The paper will explore the contracting approach to the project and the adaptation of Underground Technology Research Council (UTRC) guidelines for underground contracting to a design build project. The roles of Owner, Owner’s consultant, and design-build contractor will be defined as interpreted by the USACE and key contract provisions will be described and contrasted with a traditional design-bid-build approach to tunnel construction.

Jan 1, 2003

By Bernie W. Martin

The East Side Access (ESA) project is the largest commuter railroad project ever undertaken in the United States. The purpose of the ESA project is to bring commuters from Long Island into Grand Central Terminal. The program is estimated to cost $4.3billion. The purpose of this paper is to describe the key design elements for the Queens segment, ?re life safety, ventilation and changes to the proposed contract delivery method.

Jan 1, 2003

By David Field, David Powell, Richard Hulsen

The Mission Valley Light Rail will loop through San Diego State University (SDSU)and to minimize the impact of construction most of the works will be underground. The project will require construction of a 330-m long (1080-ft), 11.24-m wide (36.9-ft),single twin track tunnel through Stadium Conglomerate, a poorly cemented dense sandy gravel with cobbles. Key technical issues are discussed including the ground conditions and predicted ground response, the use of sequential excavation methods to control deformations and specific construction concerns such as instrumentation and monitoring. Management of the construction process to minimize risk is particularly important in this environment and the strategy selected to control the works is also considered.

Jan 1, 2001

By H. Maleki, G. Tetreault

This study was initiated by the US Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room- and-pillar mining using a continuous miner (CM) was economically sound or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets " are left in longwall mines on one side of the mains near outcrops and adverse geological conditions or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included the analysis of the geologic, geotechnical and economic factors that influence the recovery of small coal reserves; the analysis of historic changes in supply, demand and coal prices; the development of typical cost models for room-and-pillar and longwall mines; and the development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR), as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modern longwall mines and, thus, is used to evaluate the increased costs associated with adding new development sections for extraction of small reserves. The study examines the economic feasibility of using unconventional longwalls for the recovery of medium-sized reserves, depending on site-specific geologic and geometric conditions.

Jan 1, 2002

By R. Fedel-Moen, R. W. L. Kimber, B. D. Williams, S. R. Ragusa

The use o f cyanide to extract gold from ores is widespread. In the process of extracting gold, cyanide may form metal cyanide complexes with a variety of other metals present in the ore. This study was carried out to investigate the biodegradation of the Cu(I)-cyanide complex and tetracyanonickelate under varying pH and nutrient additions. Detailed studies using shake flask cultures and bioreactors showed that naturally occurring bacteria residing on gold-leach-pad ore uti¬lized the Cu(I)-cyanide complex (CuCN) and tetracyano-nickelate, Na2(NiCN4), as carbon and/or nitrogen sources. Ammonium-nitrogen (NH4+-N) and/or cyanate (CNO-) accumulated in solution as the metal cyanide complexes were degraded. The accumulation of cyanate as a product is a concern due to its toxicity. Degradation rates were increased if a growth substrate (peptone, 0.1%) was added to the medium or if bioreactors were primed with peptone before addition of the metal-cyanide complex. Tetracyanonickelate was degraded at pH 8 without added peptone, but it was not degraded at pH 10. The addition of peptone was required for degradation of the Cu(I)-cyanide complex at pH 8 and pH 10. At pH 8, the addition of peptone resulted in the accumulation of cyanate, whereas, at pH 10, cyanate was not detected in the cultures. Biodegradation of metal-cyanide complexes was faster (approximately 1.5 to ten times faster) in bioreactors than in shake flask cultures. The addition of peptone was not required for degradation of metal-cyanide complexes in bioreactors. However, priming the bioreaetor with peptone resulted in higher metal-cyanide degradation rates over multiple cycles.

Jan 1, 2000

By Kurt Egger, Emily A. Baker

Rehabilitation work at the Cameron Run Tunnels entailed the restoration of seven heavily deformed, approximately 69 m long, steel liner plate supported culverts through a CSX Railroad embankment near Alexandria, Virginia. A custom fabricated expander, equipped with four 200-ton hydraulic jacks on two expansion arms was used to push back the liner plates encroaching into the proposed tunnel profile and install the steel set support. In a second phase the tunnels were then lined with 16 cm of fiber reinforced shotcrete. Geotechnical instruments both in the tunnels and on the railroad embankment were used to monitor the effects of the rehabilitation work on the two CSX Railroad tracks above the tunnels. Freight and passenger trains were required to run uninterrupted and at maximum speeds throughout construction.

Jan 1, 2003

By Daniel McConvey

Who is the Investor? -Mainly institutional, including resource funds, other mutual funds and pension funds. -Some hedge funds. -Retail investors. -How important is the reserve disclosure to these investors? -Do these investors know the difference between a reserve and a resource?

Jan 1, 2003

By Jan E. Stache

Commercial software programs are being utilized to create and maintain a mine subsidence database in conjunction with the U.S. Bureau of mines research on mine subsidence in Illinois. A three-year survey net of monitored structures in an Illinois subdivision was entered as textual information (attributes), on an existing AutoCAD drawing. These attributes can be optionally displayed on the corresponding drawing or extracted as a text file for import to a database program. The database program, dBASEIV, allows combinations of multiple database files for extensive querying capabilities. Subsurface database files can be merged with surface database files to enhance the effectiveness of surface response analyses in mine subsidence research. The geographic information system (GIS), pcARC/INFO, was chosen to integrate existing AutoCAD drawings and dBASEIV database files into a relational database with a graphical representation. The relational database allows users to update either the graphical representation or the database, with the changes being reflected automatically in its alternate format. The increased capacity, through use of a GIS, to query combinations of database files and have the results reflected graphically has significant potential for expediting mine subsidence research.

Jan 1, 1986