Search Documents

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

By T. N. Singh

An evaluation was made on the cavability of the roof formation of Dishergarh seam including caving sequence, caving span, and load on powered support.

Jan 1, 1994

In this paper, the authors attempt to apply a simplified non-homogeneous void diffusion model (NHVDM) to predict surface subsidence for longwall mining in Illinois. A generalized error function subsidence profile is derived from this model. The model validation indicates that the NHVDM approach appears to fit the observed subsidence data as well or better than the error and the trigonometric functions, particularly around the trough edge areas.

Jan 1, 1990

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

By J. Nielen van der Merwe

This investigation was done to develop a method to predict the lie of coal pillars. It has long since been known that coal pillars deteriorate over time, but there was no method to quantify the deterioration. It was found that the rate of pillar deterioration was essentially a function of two parameters, namely mining height and time. The higher the mining height, the more rapidly the pillars deteriorated. The rate of deterioration is not constant, but decreases exponentially with time. The pillar life should be viewed in conjunction with the safety factor. While the relationship between safety factor and pillar life is ambiguous, the trend is nonetheless for higher safety factor pillars to have longer lives. The safety factor can be used to quantify a failure probability. The pillar life prediction indicates when the pillars which are predicted to fail, can be expected to do so.

Jan 1, 1998

By Thomas M. Barczak

The resultant load vector is the representation of the forces applied to a longwall roof support element by caving strata into a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield support prohibit a determination of support resistance simply by summation of leg forces. A method is being investigated by the Bureau of Nines to determine the resultant load vector by instrumenting supports with pressure transducers and strain gages to measure leg, canopy capsule, and lemnisoate link forces. This concept has been laboratory tested in the Bureau's Nine Roof Simulator. Functional relationships among variables have been assessed, and confidence intervals have been established for prediction of the resultant load vector parameters.

Jan 1, 1984

By V. D. Jalevsky

A new methodology of an experimental-analytical approach has been developed. It is used in building an information geomechanic monitoring system for the modeling of geomechanic processes during coal seam working. The approach synthesizes experimental (in-situ) measurements of rock pressure manifestation in separate points, methods of numerical modeling of processes on rock boundaries with coal, and a seam analytical calculation of rock mass in a spatial strained state. One of the realizations of this approach is the developed theory and calculation method of adjoining rock surface shift (overhang) formation during underground working of sheet deposits and of rock mass geomechanic state determination. There are description algorithms of cavity configurations with broken lengths of faces during underground working of useful mineral sheet deposits. These algorithms have been used in computer modeling of formations of adjoining rock surface overhangs and abutment pressure upon rock mass in the area of coal faces with irrectilinear longwalls. Peculiarities of surfaces shifts and stress allocation are established for different face schemes. The use of theory and methods alloww working out techniques of automatic control to receive processing algorithms of RPM measurement results and calculate geomechanic situations within panels in the process of planning and development as well as during mining, i.e., to carry out long-term prediction, in-line control, and short-term prediction of rock pressure manifestations.

Jan 1, 1996

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Ry Stone

To maintain longwall continuity, NRE Wongawilli Colliery extracted the approximately 20-year-old Thompson Mains and in doing so, 20 roadways were holed into during longwall retreat. The orientation of these roadways with regard to the longwall face varied between (i) a parallel alignment where the entire roadway was simultaneously subjected to a significant increase in vertical stress on holing and (ii) a more favorable high angle of alignment, meaning that only a portion of the roadway was subjected to an increase in vertical stress on holing. In addition, the longwall holed into and was recovered in one of the existing roadways. The geotechnical environment presented several additional challenges during longwall retreat. The orientation of the stress field resulted in a major horizontal stress notch on the maingate and an elevation in the major horizontal stress in front of the longwall face during the retreat up to an adjacent goaf edge. The presence of geological structure zones also resulted in both swings in the major horizontal stress direction and increased levels of roof deformation. The gate road support designs were based on commonly accepted strata management techniques and principles. The support designs in the hole-through roadways were based on empirical design models generated from (i) aconceptual geomechanical model of pre-driven hole-throughand recovery roads and (ii) a worldwide database on pre-driven hole-throughand recovery roads. Imperative to the success of extracting the panel was a sitespecific strata management process. In this regard, consideration was given to the following: roof displacement monitoring in the gate roads (in particular, Longwall (LW) Acceleration Position), roof-to-floor convergence monitoring in the hole-through roadways, the ability of the mine to limit downtime prior to and during holing by utilizing an Authority to Mine (ATM) type process, and the use of Trigger Action Response Plans (TARP).

Jan 1, 2012

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By R. Balia

The upper part of the "Contatto Ovest" orebody, at the San Giovanni Pb-Zn sulphur mine (Sardinia, Italy), is mined by a sublevel caving method. With increasing mining depth, a progressive caving of the hanging wall and discontinuous subsidence occurs. The orebody, which is located very close to the contact between the Cambrian limestones and the Silurian shales, strikes NE-SW for more than 100 m and dips 75-80' NW. The limestone footwall is massive and strong while the hanging-wall consists of very weak shales. The mine considered is located near a town so that the observed subsidence effects must be taken into account for both stability of the nearby railway and houses and morphological and environmental impact. A limiting equilibrium analysis to predict the progress of hanging wall failure with increasing mining depth was used. A suitable computer program was developed for solving the model by a iterative procedure. The progressive hanging wall caving and its consequent superficial effects were predicted perfectly by means of the computer program used and later confirmed by a geophysical test (seismic tomography). Our study ends with a further analysis, carried out using the same procedure, which allows to have a different geometrical situation with the presence of a pillar to protect the mill area.

Jan 1, 1990

By Gabriel S. Esterhuizen

This paper addresses the need for a method to compare the effectiveness of different support systems when designing ground support in coal mines. At present, support design methods include empirical methods based on observations of past performance of installed support systems, analytical methods where the roof is typically simulated by elastic beams and numerical model analysis. The approach presented in this paper estimates the relative stability of a support design through geotechnical evaluation of the rock mass and numerical model analysis of the interaction between the rock mass and the support system. Models are used first to simulate the design performance at the expected rock conditions. The rock strength is then reduced until collapse is indicated in the model. The stability factor is then calculated as the ratio of the expected rock mass strength to the rock mass strength at the onset of collapse, and is similar to the well-known factor of safety used in engineering practice. The stability factor can be used to assist in developing a final support design by comparing the effectiveness of various support systems and the stability of excavations under various geological and loading conditions. Examples of the method?s application in three different geological settings are presented.

Jan 1, 2012

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

By W. Smith

The U.S. Bureau of Mines (USBM) is using laboratory and computer-based techniques to investigate the post- failure behavior of yielding pillars and pillar reinforcement techniques to control entry deformation. Poorly dimensioned yield pillars, can cause adverse ground conditions. Laboratory studies to evaluate various reinforcement techniques for controlling yield pillar deformation were conducted. A cracking and crushing model is used to evaluate potential tensile and compressive failure planes within pillars of various widths to assess the degree of yielding and stress redistribution. The use of an elasto-plastic model to evaluate the effect of various reinforcement on yield pillars is also discussed. These procedures effectively account for the residual pillar strength, important in yield pillar design.

Jan 1, 1995

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By J. Brasfield

Jim Walter Resources, along with the Rock Mechanics Branch of British Coal and Strata Control Technology Pty. Ltd., is presently studying the yield-stable-yield pillar design in use at the Blue Creek No. 7 Mine located in Brookwood, Alabama. This paper describes the steps taken to determine stresses on the strata surrounding the pre-driven development entries. It also describes the installation and monitoring of stress cells and extensometers used to quantify the stress build-up and strata movement associated with the headgate pass of a longwall panel. The findings of this study will be used to design and predict the performance of a 2 entry yield pillar system in the Parkgate Seam at Welbeck Colliery in the United Kingdom. Stress measurements and strata movement data from No. 7 Mine and Welbeck will be used to develop a computer model that can predict the performance of such a pillar system in British mines. Jim Walter Resources will use this data to study the performance of the present yield-stable-yield pillar system in order to determine if conditions will allow the stable pillar width to be decreased while maintaining current standards of safety and production.

Jan 1, 1994

By L. J. Lorig

Much of the present knowledge about caving behavior of rock masses has been obtained from empirical observations. Additional notions about caving have been developed through inferences derived from two-dimensional finite element analyses. These analyses have indicated that a combination of one low-angle set of fractures and one nearly vertical set of fractures is the optimum fracturing configuration for ease of cavability of an orebody. This paper presents the results of two- and three-dimensional distinct element analyses which draw different conclusions than those reported from finite element studies. The distinct element method is selected far analysis of cavability because this method treats the rock mass as an assemblage of rock blocks which may interact individually, The results of the analyses are compared to a documented case history which involved a groundfall of 80,000 tons of ore in a 160-foot high pillar. The mechanics associated with these results are-explained in terms of simple static stability analysis of wedges. The propensity for orebody caving is primarily a function of the number of joint sets or potential "release" surfaces in the orebody. This mechanism is influenced by the bounding weak discontinuities, and intact strength of rock material.

Jan 1, 1989

By Michael Kelly

Inertial navigation technology has, for the first time, allowed the position of a longwall shearer to be mapped in three dimensions. Following the success of the technology in highwall mining and successful trials on a longwall face, the Australian Coal Association Research Program (ACARP) commissioned a three year "Landmark" project that aimed to advance longwall automation to the level of "on-face observation" by the end of 2004. This project has been completed with the following successful technical outcomes: Automatic face alignment was achieved, using an inertial navigation-based sensor on the shearer, to accurately measure face geometry and feedback signals used to move OEM (Original Equipment Manufacturer) roof supports. Operational on-line measurement of creep with creep information incorporated into face alignment corrections. Inertial Navigation System (INS)-based enhanced horizon control was bench-tested. Operational broadband communications system to shearer using wireless Ethernet on a commercial-product basis. Acquisition of located coal-face features for use in thermal infrared-based horizon control. Automated Longwall Information System (LIS) developed which integrates information from multiple systems and sensors and provides high quality visualisation and control interfaces. Automatic roadway and face convergence monitoring tools successfully tested. Condition monitoring tools developed and demonstrated for improved face reliability. This paper summarises the outcomes of the project and describes the work being undertaken for the 2 year Landmark Extension project approved in April 2005. Consistent with the conference theme, the paper focuses on the ground control aspects of the project.

Jan 1, 2005

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992