Search Documents

By Hsin H. Huang

Equilibrium calculational software programs can be effectively utilized to model the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation on extraction and recovery processes. Illustrative examples using the calculational program ST ABCAL for the creation of diagrams such as EwpH, activity or concentration-pH, and activity or concentration-EH are presented to demonstrate the fundamental characteristics of real hydrometallurgical mercury dissolution and recovery processes. An industrial application will include leaching of mercury from K 106 mercury sulfide waste and solution purification by iron cementation.

Jan 1, 2003

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-Si02 and FenO-MgO-CaO-Si02 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below 11 mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-Si02 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe304 on the viscosity was quite significant. The viscosity of slag increased by 300mPa's at l573K when Fe304 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-Si02 and FenO-MgO-CaO-Si02 systems is given in this study.

Jan 1, 2003

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below II mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-SiO2 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, .the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe3O4 on the viscosity was quite significant. The viscosity of slag increased by 300mPa-s at 1573K when Fe3O4 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 systems is given in this study.

Jan 1, 2003

By Milance Mitovski, Milorad Cirkovic, Vlastimir Trujic, Dragana Živkovic

"In this article, it is analysed the possibilitis and the effects utility waste energy of process sulfuric acid production in the existing technical-technological conditions. The utility second process energy, reduction the fuels consumption, reduction environment pollution and its effects are shown, too. High heat quantity is produced as the result of exothermal reactions in the production process of sulfuric acid in Bor. A part of this heat is sufficient for the process development, and significant part of this heat presents low-temperature heat energy that is irretrievable lost. Investigations were carried out based on production of 485 t of monohydrate/day of sulfuric acid. By recovery of this heat quantity for heating purposes, about 20.000 – 25.000 t of coal/year would be saved, what would significantly improve the power efficiency of the smelter copper production. IntroductionTechnological process of copper production in RTB BOR (Serbia) produces a significant quantities of high temperature secondary (waste) heat energy that is uncontrolled “lost” in the vicinity. Secondary heat energy is produced in pyrometallurgical copper production in quantity of 1,621 kWth/kg of dry concentrate or existing heat (that presents a difference of heat at furnace outlet and heat at temperature over temperature of dew point of sulphuric acid gases) in quantity of 1,315 kWth/kg of dry concentrate. For designed capacity of Copper Smelter in Bor, the existing heat power of secondary energy is 92,111 MWt, what is an equivalent to the power of steam-turbo plant where the Rankine-Clausius heating cycle is done, and that is 28,334 MWe."

Jan 1, 2008

By Antonio Luraschi

The constituents iron, oxygen, silica and cop- per are of principal interest in slags utilized in pyrornetallurgical processes for producing copper. Accordingly, phase relationships in the.Cu-Fe-0-SiO2 system are important when one considers the physico- chemical behavior of slags. These phase relation- ships for the quaternary and constituent ternary systems are developed from available information. Isothermal composition and composition-oxygen potential diagrams, and oxygen potential-temperature diagrams are utilized to describe the' important relationships.

Jan 1, 1976

By E. Anelli

Based on experimental continuous cooling transformation (CCT) diagrams, an artificial neural network has been trained to predict the amount of microsturctural constituents and hardness resulting from and controlled cooling at rates from 150 to 0.015 K/s. It can be applied to quenching and normalizing processes of low-alloy steels with 0.05-0.30 C% and 0.4-2.0% Mn -with possible microalloying additions. Examples of the good predictive capabilities about 15 Vickers standard deviation for hardness and a few percent for volume fraction of phases) are reported' Keywords: Austenite decomposition, low. And medium-carbon steels, artificial neural networks

Jan 1, 2003

By L. Petitnicolas

The experimental study of nitrogen absorption and its removal from a liquid Ni-20%Cr alloy at 1873 K has been undertaken, using an experimental, apparatus based on the Sieverts technique in order to determine the solubility of nitrogen in the alloy. as well as the kinetics of nitrogen transfer across the gas/melt interface. Experiments show that nitrogen solute equilibrium content can be calculated using the Sievens law. Measurements point out the nitrogen absorption reaction rate to be well described by first order kinetics, whereas experiments on nitrogen removal reveal that the rate is better expressed using a second order equation.

Jan 1, 1996

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By Toshiyuki Hashida, Victor M. Lopez-Hirata

"Small-punch tests and determination of fracture toughness JIC were conducted at 4 and 77 K on new cryogenic JN1, JJ1 and JK2 austenitic stainless steels, after isothermal aging. Equivalent fracture strain ?qf determined by measuring the reduction of thickness in the small-punch test specimen. A linear dependence of JIC on ?qf was found in these new materials. Regression analysis of experimental data produced the following linear relation JIC = 1304.1 ?qf + 8.09 [kJm-2]. An analysis of present work relation was pursued on the basis of material properties and evaluation method of he. Results showed that the slope value has a strong dependence on material yield strength and JIC evaluation method. This linear relation is useful for the evaluation of fracture toughness JIC, measuring the equivalent fracture strain ?qf by means of small-punch test. Thus it can be useful for assessing the degradation of fracture toughness in small areas such as, the heat-affected zone in welded components.IntroductionCryogenic structural materials for superconducting magnets of fusion nuclear reactor are required to possess a good combination of strength and toughness. The mechanical properties are required beyond the capability of conventional austenitic stainless steels [1]. New cryogenic JN1, JJ1 and JK2 austenitic stainless steels were developed by the Japan Atomic Energy Research Institute (JAERI) [1]. The structure of superconducting magnets is constructed by welding of 200 = thick plates of these steels, which are solution treated at high temperatures and then water-quenched to avoid intergranular precipitation. However, the welding process involves heating and cooling [2], which cause microstructural changes in both base metal and weld. In this heterogeneous microstructure, it is important to estimate the fracture toughness of these materials at cryogenic temperatures. Therefore, it is necessary to evaluate the effect of aging process on the fracture toughness behavior of these new steels. To determine the cryogenic fracture toughness, the elastic-plastic JIC value has been co=only used [2]; however, the specimen size is much larger than heat-affected zones in welded components. Small-punch (SP) testing method, employing miniature specimens, has permitted to evaluate the fracture toughness behavior at different temperatures in different nuclear reactor materials [3,4]. Mao et al. [5,6] and Misawa et al. [7] found a linear relation between JIC value and equivalent fracture strain ?qf, determined by SP method in non-ferrous alloys and ferritic steels at room temperature and austenitic stainless steels at 4 and 77 K, respectively. So that, this kind of correlation would be very useful to assess the fracture toughness JICe values by means of SP test in small zones of welded components."

Jan 1, 2012

By Rune Gammelsmter

Turbulent chemically reacting flows are generally very complex, involving interactions of chemical, thermodynamic, and fluid mechanical processes. A combustion model based oh algebraic moment closure has been developed. The model is applicable for reaction rates where the chemical kinetics can vary from slow to fast. The effects of turbulence is taken into account by means of modifications to the well known k-e modelling procedure. The model is applied to an industrial combustion process. Calculation of furnace off-gas combustion from an aluminum reduction cell has been performed. The theoretical results agree well with experimental values.

Jan 1, 1992

By V. Panchanathan

The rapidly solidified Nd-Fe-B powders form the entire basis of the bonded magnet industry At present the rapid solidification is carried out exclusively by melt spinning, producing flake like particles having highly stable and magnetically hard microstructure These particles are comminuted into powder before being processed into bonded magnets These powders are magnetically isotropic having coercivities from 4 to 16 kOe The other type of powder recently introduced for bonded magnets is the anisotropic powder made by the hydrogen decomposition desorption recombination (HDDR) process. The characteristics and application of these isotropic and anisotropic powders are discussed.

Jan 1, 1997

By E. Morrice

Solubility of yttrium oxide (Y203) in fluoride melts was experimentally measured in the temperature range of 998 to 1273 K and, YF3 composition in LiF.YF3 melts varying from 20 to 50 mole pct using a graphite crucible in an argon atmosphere. Solubility of oxide in the melt was found to increase with increasing temperature and YF3 composition in the melt. An expression for in XY2O3 as a function of temperature for several melts was deduced. The calculated activity coefficients of Y2O3 in the melts exhibited a negative deviation from Raoult's law.

Jan 1, 1989

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By Hiroaki Kawamura, Takeshi Yoshikawa, Kazuki Morita, Yutaka Yanaba

"To develop an alternative metallurgical process for phosphorus removal in the production of solar-grade silicon (SOG-Si), slag treatment of metallurgical-grade silicon (MG-Si) was conducted, followed by acid leaching. Phosphorus-doped silicon alloy or MG-Si containing certain amounts of phosphorus and calcium was reacted at 1723 K and 1773 K with CaO--CaF2 of several compositions. Phosphorus removal from the molten silicon into the slag phase was confirmed by reduction to phosphide ions, P3-, and phosphate ions, P3-. These ions were separately determined using a wet chemical analysis method developed by ourselves. The highest phosphorus distribution ratio obtained was 2. 7 after reaction for 18 h with 17.5 mass% CaO--CaF2 slag. We then conducted acid leaching of the silicon and achieved removal of a large fraction (over 90 % ) of the phosphorus, which was much higher than that obtained by ordinary oxidizing slag treatment.IntroductionIn recent years, the production of solar cells has been increasing rapidly. Because of this, the demand for solar-grade silicon (SOG-Si) has also been growing rapidly. The development of lower-cost mass production processes is therefore needed to provide silicon feedstock. Phosphorus is one of the impurities in metallurgical-grade silicon (MG-Si). Because of its large segregation coefficient (kp = 0.35) [l ], it is difficult to remove phosphorus using a solidification refining process. Vacuum melting is considered to be a promising method for removing phosphorous from MG-Si [2], but the issues of high cost and large energy consumption have still to be resolved.Slag treatment is often used to remove impurity elements by oxidizing reactions during general oxidation refining processes. For example, phosphorus in molten steel is removed into a slag phase as phosphate ions, PO4 3-l-, by the following reaction:"

Jan 1, 2013

By Nathaniel R. Quick

"Nd: YAG, KrF excimer, and Cu-vapor lasers are used in air to synthesize conductors and semiconductors as a second phase in silicon carbide and aluminum nitride. Conductor resistivities as low as 104 O-cm are formed in these substrates; the resistivities for the untreated substrates range from 10 11to 1014 O-cm. The silicon carbide conversion is relatively independent of wavelength while the aluminum nitride conversion shows a dependence on wavelength over the range 248 nm to 1064 nm. Silicon carbide conductors, evaluated over the range 15 K to greater than 300 K, exhibit metal like conductivity; resistivity increases with temperature. Silicon, carbon, and oxygen are identified as the principal chemical species associated with the conductor in SiC substrates while aluminum, nitrogen, and oxygen are identified as the principal chemical species associated with the conductor in aluminum nitride substrates. The silicon carbide system, which has the less complex phase diagram, is evaluated in more depth to explain the synthesis mechanism. Oxygen was principally on the surface and increasing SiC conductivity is associated with decreasing spacing between 5 µm, or less, diameter carbon globules. This technology is proposed as a replacement for metallization in electronic packages, sensors and devices. INTRODUCTIONCeramics are commonly used for multichip module, hybrid and multilayer electronic packaging; semiconductor device and sensor applications because of the insulating, conducting, semiconducting, or superconducting properties that these materials possess (1,2) The majority of ceramics, however, have not been known to exhibit conductive or semi conductive properties when exposed to rapid thermal heat processing. A ceramic and process which through selective conversion can combine two or more of these electrical properties to eliminate the need for metallization is of interest to both the commercial and military sectors."

Jan 1, 1994

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000