Search Documents

By W. F. Chiao, R. B. Gordon

Tile sharp-yield point found in magnesium crystals in the solulion-treated and aged condition is studied by dislocation internal-friction experiments. The results show that the sharp yield is not file to the sudden release of pinned dislocations hut is movc likely due to the rapid multiplication of an initially small number of dislocations. Recovery or the dislocation internal friction after deformation is also studied. This yecovery results from the re-pinning of dislocations by a solute, presumably nitrogen, which moves with a relatively small activation energy. SHARP-yield points, when they occur, are a striking feature of the stress-strain curve generated during a tensile test. Although commonly associated with steel, sharp yielding has been found in a variety of metallic and nonmetallic crystalline materials. In particular, sharp-yield points have been found in zinc"' and cadmium3 containing nitrogen. With this background, Geiselman and Guy4 investigated the tensile properties of magnesium single crystals containing nitrogen to see if sharp yielding also occurs in this system. They found that sharp yields did indeed occur in solution-treated and aged specimens tested at elevated temperature but were not able to give conclusive proof that the sharp yield was caused by nitrogen, a yield drop being observed even in their purest crystals. Sharp-yield points have also been found in various polycrystalline magnesium alloys.7'8 In the study of the sharp-yield phenomenon it is desired to observe the behavior of dislocations in the earliest stages of the deformation process. Internal-friction experiments are useful for this purpose because dislocation damping is sensitive to the mobility of free-dislocation segments. At low strain amplitudes the damping, A, due to the the forced vibration of dislocation segments of average length L is ? =KAL4 [1] where A is the dislocation density and K, if the applied frequency is well below the resonant frequency of the dislocation segments? is a constant for the sample under observation.5 Dislocation damping, because of the fourth-power dependence on L, is particularly sensitive to the creation of free-dislocation segments during deformation. Since sharp yielding is associated with the sudden release of pinned-dislocation segments, marked changes in the dislocation damping are expected at the yield point.6 The use of the dislocation-damping observations to help elucidate the incompletely understood mechanism of yielding in magnesium is the primary objective of the experiments reported here. PROCEDURE Many investigations have shown that very marked and rapid changes occur in the dislocation damping of of a deformed material as soon as the straining is stopped.5 It was quite essential, then, for the purpose of this investigation, to make the damping measurements during the deformation of the samples. This can only be accomplished through the use of the ultrasonic-pulse method. In this method traveling sound-wave pulses are used and, in contrast to resonating-bar methods, only the sample ends are set in vibration. Thus, the sample can be gripped along its sides in the tensile-test machine without disturbing the damping measurements. In the pulse method, the decrease in the amplitude of a sound pulse is measured as it travels back and forth through the sample. If A is the amplitude after traversing a distance x and A. is the initial amplitude, A=Aoe-ax [2] and a is called the attenuation. It is commonly measured either in units of cm-I or as db per µ sec. The observed attenuation in a metal sample is due to a number of causes. These include scattering by grain boundaries and impurity particles, thermo-elastic damping, diffraction effects, stress-induced ordering of solute atoms, and dislocation damping. The total observed attenuation in a given sample usually cannot be resolved into these various components, but changes in a due solely to changes in dislocation damping can be accurately determined, provided the experiment is arranged so that all other sources of damping are held constant. It is desired to reduce the extraneous sources of attenuation to a minimum and for this reason the experiments are done on single crystals of high purity. Magnesium crystals offer the further advantage that, when properly oriented, only a single set of slip planes is active during deformation. Crystal Preparation. The method of sample preparation is similar to that of Geiselman and Guy.4 The starting material was high-purity, sublimed magnesium rod supplied by the Dow Chemical Co. Melting under Dow 310 flux was used to reduce the nitrogen content of the starting material: the fluxing was done under an argon atmosphere and the

Jan 1, 1965

By R. E. Zinkham, R. J. Goodwin

A mathematical study has been made of the amount of support a cement sheath could provide to casing cemented into the earth. Several assumptions were required to make the analysis, but only two of them are limiting: (I) the pipe must be completely surrounded with cement, and (2) any mud filter cake between the cement and formation has the same physical properties as either the cement or formation. The calculations showed that little support would be provided to the pipe before an unsupported cement sheath failed in tension; however, when the cement is confined between the pipe and wellbore and is loaded in compression, the pipe could receive a considerable amount of support. In fact, the theoretical results indicate the lower grades and larger sizes of pipe could have their working pressures doubled when reasonable compressive loads were applied to a surrounding cement sheath. These data are shown in six charts. Other down-hole conditions such as setting the cement under pressure, increased temperature and cement confinement all tend to increase the potential usefulness of the sheath. Because of size limitations, a laboratory program to verify the most important results of this mathematical study would be very difficult. However, small-scale field tests would be practicable. This paper shows that, if a solid cement sheath can be obtained in the field by either primary cementing or by repair after detection of flaws by surveys such as the new cement-bond logs, the use of this approach to reducing pipe costs merits further consideration. INTRODUCTION A modification in casing design practices is proposed which may either reduce the amount and grade of steel required to contain a specified internal pressure or permit the working pressure to be increased for a specified weight and grade of pipe. One of the more important considerations in casing design is its resistance to collapse; however, Bowers' and, more recently, O'Brien and Goins' have shown many casing programs are unnecessarily conservative in this respect, and they have indicated how savings can be made by designing for more realistic down-hole conditions. Earlier, Saye and Richardson howed that pipe costs could be reduced by considering the cement sheath as a part of the casing string when collapse resistance was being calculated. More recently, Rogers4 has raised the question as to whether a cement sheath might be considered in the design for burst resistance of the cemented casing. Calculations have been made for the increased burst resistance a cement sheath would provide for casing in a wellbore, and the results show that a sizable amount of support could be obtained in some instances. These data are presented in addition to a discussion of several other factors that are considered to affect the burst strength of pipe supported by cement. Two types of support are treated: Case I for tensile loading of the unconfined cement sheath, and Case for compressive loading of the confined cement sheath. ANALYTICAL TREATMENT AND RESULTS CASE I—TENSILE STRESSES IN AN UNCONFINED CEMENT SHEATH Conditions like this would most likely occur in a greatly enlarged portion of the hole where the cement was not in immediate contact with either the formation or a thin and hard mud cake. The mathematical analysis for this condition, as shown in the Appendix, rests on the following concepts. Pressure inside a unit length of pipe causes: (1) a tensile or tangential stress to be exerted over the longitudinal cross-sectional areas of the pipe and cement; and (2) an equal amount of strain in both the pipe and cement that is uniformly distributed over the wall thickness of each. This analysis was then used to make several calculations for a cement sheath around 51/2-in. OD pipe. The results are illustrated in Fig. 1, which shows that a tensile stress of 500 psi is imposed on a 5-in. thick sheath when the casing contains a pressure of only 1,450 psi. It also shows that a 10-in. thick sheath would be stressed to 500 psi in tension when the pipe contained a pressure of only 2,350 psi. Alternatively, if the stress analysis is made by means of the Lame thick-wall cylinder theory, the inner fibers of the 10-in. thick sheath will be stressed to 500 psi in tension when the pressure in the pipe is only 990 psi. This, of course, reveals that an unconfined sheath is of little support to the pipe in burst; however, an entirely different result is obtained when the cement is confined between the pipe and formation.

By C. J. Bechtoldt, H. C. Vacher

Quenched alloys, prepared by powder metallurgical techniques, were examined by microscopic and X-ray diffraction methods. The compositions and heat treatments were chosen so that the chromium and nickel solvuses could be determined and a range of composition and temperature, in which a eutectoid had been reported, could be explored in small intervals. The results showed no evidence of eutectoid reactions having taken place. ALLOYS containing iron, chromium, molybdenum, and nickel are extensively used in high-temperature applications. In order to provide basic information on the solid-state reactions that occur in such alloys, the National Bureau of Standards is engaged in an extensive study of the equilibrium phases in the binary, ternary, and quaternary systems involving these four metals. Attention was directed to the chromium-nickel system because a review of the literature showed conflicting data. A recent compendium1 of the constitution of binary alloys gives two diagrams for the chromium-nickel system, one a simple eutectic and the second a diagram showing a eutectoid and a eutectic. The eutectoid was the result of an allotropic transformation in a high-temperature solid-solution form of a chromium-rich phase called 0. The approximate temperature and composition of the eutectoid was 1200°C and 30 at. pct Ni. In the preliminary study, at the Bureau, no transformation was indicated in the chromium-rich phase of ternary and quaternary alloys in which chromium and nickel were major components. Similar results have been reported from time to time in the literature,2-8 In consequence of this situation, a systematic study was made of the constitution of heat-treated chromium-nickel alloys using metallographic and X-ray diffraction methods. The compositions of the alloys were selected so as to determine the boundaries of the chromium-rich and the nickel-rich phases and to explore in small intervals the ranges in composition and temperature in which the eutectoid had been reported. The results of this study are reported and discussed in the present paper. EXPERIMENTAL PROCEDURES Materials, Alloys, and Heat Treatments—The alloys were prepared by a powder metallurgy technique similar to that used in earlier work.9 Analyses of the materials used are given in Table I. Powders were mixed using a vibrator in 30-g batches of predetermined composition; 2-g pellets were made from the mixture by compacting at room temperature in a 1/2-in. diam mold under 60,000 lb per sq in. pressure. The pellets were sintered in dry hydrogen for 10 days at 1300°C. At the end of the sintering treatment the specimens were quenched in water, which caused a pale green film to form on the chromium-rich alloys and thin black scale to form on the nickel-rich alloys. The pellets after sintering were approximately 1/2 in. diam by 3/32 in. thick. The purification train9 was modified by inserting a tube of titanium turnings, heated at 700°C to increase the efficiency of the removal of oxgen and nitrogen. It was found in the earlier work that the sintering treatment lowered the carbon, oxygen, and nitrogen contents of chromium-rich alloys to 0.01, 0.01, and 0.004 wt pct, respectively, and that there was a loss of chromium. In order to ascertain the extent of this loss, the chromium contents of certain alloys were determined chemically. They included those alloys used to determine the parameter-composition curves and those of critical composition, used to determine the chromium-solvus microscopically; these analyses were made on samples after the final heat treatments. The mixed powder values for the chromium content of those alloys that were not analyzed were adjusted to conform to a smooth curve based on the chemically analyzed values for

Jan 1, 1962

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y' alloys by gas quenching, is extensively ordered prior to y' (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y', Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y'. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y', or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.' The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.' An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By E. Douglas Sethness

The uranium industry is booming. In Texas alone, there are about 22 different companies with active exploration programs. Twelve solution mines have been permitted; three surface mines have been authorized; and two mills are currently in operation. However, the industry also has a problem, and that is the disposal of radioactive wastes. Over the past several years, stories concerning nuclear wastes have appeared frequently in the news. One of the most frequently cited cases occurred in Grand Junction, Colorado. In 1966, after ten years of investigations, the U. S. Public Health Service (PHS) discovered that tailings from a uranium mill were being used as fill material and aggregate for local construction purposes. It was estimated that between 150,000 and 200,000 tons of material had been removed and used under streets, driveways, swimming pools, and sewer lines. In addition, tailings had been used under concrete slabs and around foundations of occupiable structures. Further studies prompted the Surgeon General to warn that the risk of leukemia and lung cancer could be doubled at the measured radiation levels. More recently, the L. B. Foster Company discovered that its building site in Washington, West Virginia, was radioactive. While digging a foundation, the ground erupted and a ball of fire 30 feet high shot out. Evidently, the dirt was laced with radioactive thorium and zirconium, a potentially explosive mixture contained in a Nigerian sand which had been used by the previous site owners in the manufacture of nuclear fuel rods. Just this month we have read about legal suits to stop exploration for a nuclear waste disposal site in Randall County, Texas. The U. S. Department of Energy is trying to locate a deep underground nuclear waste depository for final burial of over 76 million gallons of high-level wastes. The problem is acute, the wastes are accumulating at a rate of about 300,000 gallons per year. Nor do these numbers include the spent fuel elements from nuclear power plants that are in temporary storage facilities. Fortunately, public awareness of these and other related issues is high. Unfortunately, the differences in the waste products from the nuclear fuel cycle are not always apparent to the general public. There are two distinct types of radioactive wastes: "high-level", which consist of spent fuel or wastes from the reprocessing of spent fuel; and "low-level", which, in general, are by-product wastes. There are numerous non-technical definitions that can be applied to help the layman differentiate between high-level and low-level wastes. For this latter purpose, it is best to think of them in terms of what we can see and feel. In general, high-level wastes are physically hot and can cause acute radiation sickness in a short period of time. Low-level wastes are not hot, but may cause chronic health effects after long exposure. The wastes which we are concerned with in the uranium mining and milling industry are low-level wastes. As recently as ten years ago, there were very few controls or regulations governing tailings disposal methods. At the same time, mine reclamation was not enforced through either state or Federal laws and the long-term viability of abandoned tailings ponds was not assured. The regulatory climate has changed significantly in the last decade, however. The low-level radioactive wastes generated by uranium mining and milling are generally contained in a tailings pond. Approximately 85-97% of the total radioactivity contained in uranium ore is present in the mill waste that goes to such tailings ponds. The isotope Radium-226 is probably the most potentially harmful radioactive parameter in the ponds. Radium emits gamma radiation and is also an alpha particle emitter. Because gamma radiation is very penetrating, it presents a potential health problem when a source is located external to the body. Gamma radiation will go through the body, causing damage to each cell encountered on the way. Although alpha particles have very little penetration capability, they can cause extensive cell damage. For this reason, alpha particles are a problem after inhalation or ingestion. Radium creates a health hazard by both of these mechanisms. Radium decays to radon gas which can be inhaled and serve as an alpha particle emitter. Additionally, radium is very soluble and readily enters the natural hydrologic cycle if allowed to leach from a tailings pond. With a half-life of 1620 years, radium has plenty of time to be taken into the food chain and end up in our bodies, emitting alpha particles. Because the potential health problems are better understood today than ten years ago, and because the Nuclear Regulatory Commission (NRC) has developed increasingly stringent government regulations, the uranium mining industry applies a high level of technology to the disposal of nuclear wastes. In most cases, low-level radioactive wastes are disposed of at or near the site where they are produced. There are six commercial burial grounds for low-level wastes, but it would not be economical to ship all mine or milling wastes to these sites. The on-site disposal methods most often used are ponding

Jan 1, 1979

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij'usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith's determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej'ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of' damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.'2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

By M. R. J. Wyllie, Walter D. Rose

The use of electrical well logs for the quantitative determination of such reservoir parameters as connate water saturation, formation permeability and connate water salinity has recently been attracting the attention of a number of workers1,2,3,4,5. While the theory of the determination of connate water salinity from the self potential S.P. log has received rather detailed treatment, relatively little attention has been paid to the theoretical aspects involved in the quantitative interpretation of resistivity data. It is clear that if electrical well logs can be used for the quantitative evaluation of physical characteristics of reservoir rock, they will provide a valuable tool to supplement cheaply information obtained by more laborious core analysis. In certain cases it is conceivable that the coring program could be considerably curtailed if the electric log could be relied upon to give reasonably accurate quantitative information. It is our object in this paper to examine the theoretical basis of quantitative log interpretation as expressed in such well-established logging concepts as formation factor and cementation factor. It is also our object to investigate the physical aspects of the rela- tionship which is presumed to exist between resistivity index and brine saturation in reservoir rock. In particular, we will endeavor to draw attention to the fact that it is possible to express these logging concepts in terms of capillary pressure-saturation relationships, permeability and tortuosity, parameters which we will consider in this paper to be fundamentally indicative of rock texture. The probability of being able to obtain from log recordings alone the data theoretically essential to permit quantitative log interpretatiou will be examined, and consideration will also be given to the problem of formulating simple semi-empirical relationships for use in the field. THEORETICAL CONSIDERATIONS The concept of formation resistivity factor, or as it is now commonly called, formation factor, appears to have been introduced by G. E. Archie",". Formation resistivity factor as defined by Archie is the resistivity of a rock 100 per cent brine-saturated divided by the resistivity of the brine. This relationship had previously been used by physical chemists and the concept is, for example, implicit in an early treatment by Fricke7 of the conductivity of aqueous slurries. Archie was able to establish the fact that although the relationship between formation factor and porosity did not change too greatly for different rock textures, the relationship between formation factor and permeability was markedly dependent on rock texture. The relationship found by Archie between formation factor and porosity was expanded by H. Guyod8. Archie had suggested that the formation factor, F, could be expressed in terms of the porosity, F, as follows: F =F-m .... (11 where, F = effective porosity fraction of the sand, and, m = an exponent greater than about 1.3. Guyod introduced the term cementation factor for the exponent, m, since it may be qualitatively shown that formation factor for any given porosity tends to increase as the sand becomes more cemented. It would appear that the concept of m as an exponent representing the cementation in a sand is strictly only of qualitative value, since the quantitative estimation of m by means other than the determination of F and F has not been possible. Guyod suggests that m can be estimated from a visual examination of a sample of rock, but this method appears to be both arbitrary and unreliable. It can be said, however, that in intergranular reservoirs of practical interest, the range of m is from about 1.4 to 3.0. A possible explanation for the fact that m is found to lie between these limits will be offered below. The determination of formation factor is an essential preliminary to the

Jan 1, 1950

By C. H. Hewitt, J. T. Morgan

The Fry cocurrent in situ combustion project was carried out in a 3.3-acre portion of a lenticular body of Robinson sandstone of Lower Pennsylvanian age. This particular sand body is about 12,000 ft long and 3,500 ft wide; it varies in thickness from 0 to 55 ft, trends northeast-southwest, and occurs at depths between 880 and 936 ft. The reservoir is made lip of three distinct types of sandstone, each having characteristic reservoir properties. (See Table I.) Textural gradients, sedimentary structures, erosional basal contact, absence of marine fossils, and geometry of the sand body all indicate that the sandstone is of fluvial origin and part of an extensive complex of river-deposited sedirnents. Geographically oriented cores reveal that the direction of depositing currents was to the southwest, parallel with the sand-body trend. Directions of maximum pernleability also parallel the northeast-southwest trend. The layered nature of the sandstone reservoir and its directional properties have controlled the areal distribution of produced gas, the ignition behavior, and the vertical profile and horizontal extent of the conbustion zone. INTRODUCTION This paper is the first of a series of three papers that describe Marathon Oil Co.'s Fry in situ combustion test. This first paper contains the results of a detailed study of the geology and reservoir characteristics of the Robinson sandstone reservoir in which the Fry test was conducted. The second and third parts of this series report on the field operations' and performance. The geologic work reiated to cores cut through the combustion zone, and to the effect of reservoir properties on the combustion process is included in the third paper.' GEOLOGIC STUDY OF THE FRY RESERVOIR The close spacing of continuous cores in the Fry combustion site provided an unusual opportunity to study the details of distribution of lithology and reservoir properties within a petroleum reservoir. The objectives of the study were: 1. To determine the distribution of rock types within the Robinson sandstone in the Fry area; 2. To determine the relationship of porosity and permeability to rock properties and establish the distribution and homogeneity of reservoir properties; 3. To determine the origin of the Robinson reservoirs so that attempts could be made to predict the size, shape, distribution, extent and continuity of Robinson reservoirs; and 4. To determine what effects, if any, the reservoir rocks might have on the combustion process, so that the process might be better evaluated. AVAILABLE MATERIALS Continuous cores were cut from 14 wells in the vicinity of the Fry site. Ten of the cores are from within the 3.3-acre pattern; six of the 10 were cut prior to combustion, and four were cut through the combustion zone. Cores from the Emma Fry No. 15, Wampler 0-2 and Fry B wells (Figs. 1, 2 and 9) were geographically oriented by the Eastman Oil Well Survey Co. Maps, electric

Jan 1, 1966

By N. J. Grant, R. Nordheim

An extensive study was made of the aging characteristics of alloys based on the 80 pct Ni-20 pct Cr composition hardened with aluminum and/or titanium, each up to 4 pct. Aging was followed by means of hardness and hot electrical resistance measurements as well as by X-ray and microscopy. Stress rupture tests at 1500°F were utilized as a check on the predicted behavior. THE titanium and aluminum hardened Ni-Cr alloys, exemplified by Nimonic 80 and Inconel X, constitute one of the more important groups of alloys developed to meet the demand for materials retaining their strength at elevated temperatures. For service in the temperature range 1200" to 1500°F, these alloys offer high creep resistance. With increasing service temperature, however, the strength of the simpler Ni-Cr base alloys falls off rapidly so that above 1500°F there is a significant loss of strength. The present investigation was undertaken with the hope that a better understanding of the factors controlling the precipitation hardening of these alloys would make it possible to increase the useful service temperature range. Primarily this investigation involved the study of the effects of titanium and aluminum on the hardening and the subsequent softening at elevated temperatures. The titanium and aluminum contents were each varied between 0 and 4 pct by weight at a constant nickel to chromium weight ratio of about 4:1. (Except when otherwise stated, all compositions are expressed on a weight basis.) The major part of the investigation was confined to alloys with less than 0.06 pct C. Recently several papers dealing with the identity of the microconstituents in the titanium and aluminum hardened Ni-Cr alloys have been published. Using X-ray analysis of the residues from anodic dissolution, Rosenbauml was only able to identify carbides and nitrides in Nimonic 80 and Inconel X. However, since Rosenbaum worked with alloys in the hot rolled rather than in the aged condition, his results are inconclusive. Recently Hignett' reported that the hardening of Nimonic 80 was due to the controlled precipitation of Ni,(TiAl) having the cubic Ni3A1 structure. Taylor and Floydv-" published the results of an investigation of the nickel-rich corner of the Ni-Cr-Ti, Ni-Cr-Al, and Ni-Ti-A1 systems. In the Ni-Ti and the Ni-A1 systems the hexagonal Ni,Ti phase, 7, and the cubic Ni3A1 phase, -y', respectively, exist in equilibrium with the nickel-rich solid solution. The interatomic distances in the basal plane of Ni,Ti and the octahedral planes of the matrix are almost equal, thus explaining the Wid-manstaetten type structure formed when Ni,Ti precipitates from solid solution. When Ni:,Al precipitates from solid solution, it appears usually in globular form, often dispersed along rows corresponding to definite crystallographic directions. The 7 and phases are also the only intermetallic compounds which occur in the nickel ternary alloys with up to 25 pct Cr and 10 pct Ti or Al. Taylor and Floyd found that Ni,Ti takes practically no nickel, chromium, or aluminum into solution. Nial, on the other hand, dissolves a considerable amount of chromium and titanium and some nickel. Up to three out of every five aluminum atoms could be replaced by titanium in Ni,Al. This substitution caused a slight increase (less than 1 pct) in the lattice parameter. With respect to the effect of variation in the titanium and aluminum contents on the high temperature strength of Nimonic 80 type alloys, Pfeil, Allen, and Conway" reported that an 80 pct Ni-20 pct Cr alloy containing 0.20 to 0.30 pct A1 had the highest creep resistance when the titanium content was kept between 1.65 and 2.75 pct. Experimental Procedure The materials used for this investigation were electrolytic nickel, electrolytic or low carbon chromium, sponge titanium and 2s aluminum. The alloys were melted in an indirect carbon arc furnace under

Jan 1, 1955

By R. M. Jorda

The mechanism of parafin deposition and prevention has been studied in the laboratory using an apparatus which provides a quantitative means of studying parafin deposition on metal and plastic surfaces. The amount, hardness, adhesion, per cent wax and mean molecular weight of parafin deposits appear to be governed by surface roughness alone, all other conditions being constant. Tests of various plastic coatings indicate that most smooth, nonparafinic plastics are capable of reducing parafin deposits in oil wells, but flexible, highly polar, nonparafinic plastics are more suitable for providing long term resistance to parafin deposition in oil wells if the flow stream contains abrasive materials. INTRODUCTION The problem of paraffin deposition is one of long standing in the oil industry.' Crude oils often contain paraffins which precipitate and adhere to the liner, tubing, sucker rods and surface equipment as the temperature of the producing stream decreases in the normal course of flowing, gas lifting or pumping. Heavy paraffin deposits are undesirable because they reduce the effective size of the flow conduits and restrict the production rate from the well. Where severe paraffin deposition occurs, removal of the deposits by mechanical, thermal or other means is required, resulting in costly down time and increased operating costs. The troublesome paraffins are normal hydrocarbons ranging from approximately C15H38 to C38H78 mixed with small amounts of branched paraffins, monocyclic paraffins, polycyclic paraffins and aromatics.' The amount of paraffins found in crude oils varies from less than 1 to more than 30 per cent. Many publications are available which deal with this problem, and perhaps the most significant findings in recent literature are contained in a publication by Hunt3 ho developed the "cold spot tester", a really useful means of investigating paraffin deposition. Hunt's observations led to many generalized conclusions concerning the effect of surface roughness on paraffin deposits. He ascertained that there was an observable qualitative correlation between the severity of paraffin deposition and the roughness of the surfaces which he tested (cold rolled steel, stainless steel and several plastics). Because of the number of meaningful observations made by Hunt, his cold spot tester was modified somewhat and extensive tests were per- formed to study the quantitative relationship between surface roughness and the physical and chemical nature of paraffin deposits. LABORATORY TEST PROCEDURES The cold spot test apparatus consists of a flat circular plate mounted on a curved tube and positioned in a vessel containing a wax-oil solution (Fig. 1). The apparatus is arranged so that the temperature of the central portion of the circular plate can be varied by means of a circulating liquid stream; the test equipment includes provisions for maintaining a constant wax-oil solution temperature and stirring speed. In the paraffin deposition studies, the modified cold spot tester was used as follows. The cold spot probe consisted of a flat circular plat 2 in. in diameter and 1/8-in. thick positioned in the wax-oil solution kept at constant temperature. As in Hunt's earlier experiments," a cold liquid was circulated through a tube connected to the circular plate so that the liquid impinged on one side of the plate cooling the plate from the center outward, causing paraffin to deposit on the side of the plate exposed to the wax-oil solution.

Jan 1, 1967

By E. W. Davis

IF the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indica-tions that this new process may make commercially possible the manu-facture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to mag-netite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe2O3) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red tempera-ture in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900° F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1936

By N. Standish

Heat transfer coefficients have been measured in beds of various packings irrigated with mercury and molten fusible alloy countercurrent to hot gases. The measured coefficients for both systems were found to increase with gas velocities and liquid rates. Correlations were determined which show this dependence and also indicate that heat transfer in these systems is influenced by the liquid flow characteristics and the thermal conductivity of the gas and the solid packings. A heat transfer model has beer2 proposed which explains the various features of the experimental results. On the basis of this study, which gives an insight into the heat exchange in the melting zone of the blast furnace, it was concluded that by comparison with the furnace stack heat transfer coefficients are about 1.5 times higher in the melting zone. EACH year large tonnages of metal are produced in operations which, in part, involve liquid metal irrigation of "packings" countercurrent to hot gases. The melting zone in blast furnaces and in cupolas is a good example of packings irrigated with a liquid melt countercurrent to gases. In all instances of this kind large amounts of heat are exchanged and it is desirable to have some knowledge of heat transfer phenomena involved in these systems. So far the most common method of analyzing furnace efficiencies, fuel requirements, and the general thermal state of the furnace has been through the use of heat balances. As heat balances are essentially statements of the first law of thermodynamics they give no real indication of the factors which govern heat transfer between phases in the various zones of blast furnaces. Hence, rational improvement in production efficiency and the development of theoretical models is only possible if the heat transfer characteristics are known at every stage of the process and related to the important variables involved. This has been generally recognized for some time but it was only recently that Kitaev et al.' have produced a comprehensive treatment of heat transfer in solid-gas countercurrent systems such as the blast furnace stack and the packed bed regenerator. Using their treatment it is now possible to predict the effect of particle size, thermal conductivity, bed porosity, and the flow rates of both the gas and the solid material on the heat transfer in the blast furnace stack. However, the stack of a blast furnace is only one part of an integral unit for which the heat transfer analysis cannot be complete without also considering the heat exchange in the melting zone. The complexity of heat transfer processes in this region of the furnace has so far escaped quantitative description. Yet, the melting zone accounts for a greater amount of heat exchange than all the other zones of the furnace put together. Moreover, if the reduction of oxides in the melting zone proceeds in part in the liquid state the importance of heat transfer on furnace productivity and on the metal and slag temperatures is obvious. THEORY Heat transfer for two-phase flow in packed beds is a complex problem involving a number of heat exchange paths for which interphase areas are not known with any degree of certainty. Analytical solution is, therefore, difficult. This difficulty is emphasized by noting that Rabinovich~ and Luck have only recently solved the steady-state heat transfer for simplified two-phase heat exchangers of known area. However, useful progress can be made for the system considered by making a not unreasonable assumption that the usual heat transfer considerations apply and restricting treatment to the steady state. For these conditions the rate of heat transfer dq in a height dz of a packed bed of unit area is: dq = UaATdz [I.] Integration of Eq. [I] then gives the total heat transferred: assuming both U, the overall heat transfer coefficient, and a, the interphase area, to be independent of bed height. Since a, in these systems, is unknown it is convenient to combine this term with U. The group U, then represents the overall heat transfer coefficient on a volumetric basis. If AT is linear with q, then for a bed of unit volume Eq. [Z] can be integrated to give: is the log mean of terminal temperature differences. From Eq. [3] U, can be readily calculated as q and {AT)im are experimentally obtained quantities, but a difficulty arises in interpreting its meaning. Two approaches are possible depending on whether the effect of packing in the transfer of heat is neglected or not. If the packing is thermally decoupled then the resistance concept gives the relationship: which states that the overall resistance is the sum of the gas phase and the liquid phase resistances (assuming areas are equal throughout). Because the resistance to heat transfer in liquid metals is negligible by comparison with that of the gas,4 Eq. [4] can be simplified, i.e.:

Jan 1, 1969

By B. C. Raynes

IN the early part of 1952, under the auspices of the U. S. Atomic Energy Commission, Horizons Inc. undertook an investigation dealing with the preparation of high purity thorium metal in order to develop an economically competitive production process for this metal based on a recovery of the metal by a fused salt electrolysis, since a survey of the literature of thorium chemistry indicated that electrolytic methods had not received much attention, despite the consideration that electrochemical production methods often offer attractive commercial potentialities. Thorium metal has been prepared by methods which fall into four general categories: 1) reduction of halides or double halides; 2) reduction of the oxide; 3) thermal decomposition of halides; and 4) electrolytic methods. Some of the important results obtained by various investigators since about 1900 in recorded attempts to prepare pure thorium metal are summarized in Table I. A bibliography of pertinent literature is included in this paper. Thorium is strongly electropositive and possesses a great affinity for oxygen and nitrogen. As a result the prospects for the production of high purity thorium from aqueous media or oxygen bearing compounds are remote. The most promising and profitable area of investigation for production of thorium metal lies in fused salt electrolysis. Thorium has been produced previously by this technique from halide salts in fused alkali chloride eutectic mixtures. Until recently, however, the lack of known large uses for thorium has inhibited the investigation of these methods. The basic problem in an investigation into fused salt production methods for thorium is to develop a suitable fused salt system for the economic preparation of thorium. The first portion of the work in these laboratories was a small scale investigation of the electrolysis of potassium thorium fluoride, KThF5, under a variety of conditions. High purity thorium was prepared in this manner, but the process did not appear to offer the simplest and most attractive continuous commercial operation. The work reported here relates to an all-chloride system employing thorium chloride as the cell feed. ThCL4 was produced as an anhydrous material stabilized in molten sodium chloride. This product, further diluted in NaCl, was subjected to electrolysis. The electrolytic process has been studied in cells capable of holding up to 50 lb total salt charge. Ductile, pure thorium metal has been reproducibly obtained in this operation. Considerable experimentation was carried out in the preparation of ThCL as a cell feed free from moisture, oxides, and other impurities. Thorium was cathodically deposited as a coarsely crystalline powder interspersed with residual bath salts. Aqueous procedures for separating and recovering the metal were developed. The thorium metal powder obtained has been evaluated with respect to its hardness, chemical purity, and certain other physical properties. Preparation of ThC1,—Thorium chloride, and the chlorides of some other metals (aluminum, beryllium, tantalum, zirconium, etc.) cannot be obtained from aqueous solution by direct heating and evaporation. Evaporation and heating of a solution of thorium chloride yields a hydrated salt or partially hydrated salt, and finally Tho,. Anhydrous thorium chloride is obtained by forming a hydrated ammonium chloride complex salt in acidified water solution, dehydrating this compound, and finally decomposing the double salt and subliming the ammonium chloride component. Various methods for the preparation of anhydrous thorium chloride, in accordance with this concept, were investigated as indicated in Table I1 from hydrated thorium chloride (ThCl, . 3H2O), and from thorium oxycarbonate (ThOCO,). In the method found most satisfactory for this work, thorium oxycarbonate was dissolved in an excess of concentrated HC1 to give a clear yellow solution. At least 2 mol NH,Cl were added to the solution per mol of contained thorium. Ammonium thorium chloride hydrate was crystallized from solution by cooling and saturation with HC1. The resultant complex, (NH,Cl),ThCl;xH,O, was dehydrated by evaporation at 130° to 150°C and thoroughly dried at about 250°C. The dried ammanium thorium chloride was then mixed with sodium chloride in proportions to form NaThCL or to produce a ThCL4-NaCl mixture with a given thorium content. The ammonium chloride was sublimed off at temperatures above 500°C in an inert atmosphere furnace to give an anhydrous chloride source electrolyte, essentially free of Tho, and of NKC1.

Jan 1, 1958

By G. K. Manning, A. R. Elsea, C. R. Simcoe

Boron increases the hardenability of hypoeutectoid steels by decreasing the nucleation rate of ferrite and bainite. It is postulated that concentrations of lattice imperfections, such as exist at the grain boundaries, furnish the necessary energy for nucleus formation. Boron, because of its atomic diameter, will concentrate at lattice imperfections where sites of suitable size are present. Boron will decrease the energy of these local areas by occupying these sites. This mechanism accounts for the large increase in hardenability observed with small amounts of boron. The loss of the boron hardenability effect and the boron precipitate formation are explained on the basis of increased concentration of boron at the grain boundaries either with increasing boron content of the material or with increasing temperature. COMMON alloying elements affect both the nucleation and growth rates of the austenite decomposition reactions.' This effect is largely a result of the slow diffusion rates of these elements. Although a small addition of boron markedly increases the hardenability of steel, the diffusion rate of boron, which is of the same order of magnitude as that of carbon, can hardly account for this effect. An addition of boron in the range of 0.001 to 0.003 pct is about as effective as an addition of 0.30 pct Mo, 0.40 pct Cr, or 1.25 pct Ni in increasing the hardenability of a 0.40 pct C steel;' however, increasing the carbon content of the steel decreases the effectiveness of the boron addition."' The difficulty in understanding why so small an addition of boron can replace much larger quantities of the more strategic alloys, together with the erratic behavior sometimes encountered in boron-treated steels, has interfered with their general acceptance by industry. In the belief that an understanding of the mechanism by which boron increases the hardenability of steel should lead to a more general acceptance of boron-treated steels, a research investigation to determine this mechanism was undertaken at Battelle Memorial Institute under sponsorship of Wright Air Development Center. Experimental Work In order to study the effect of boron on the transformation of austenite to ferrite and bainite, a group of steels was made with a basic composition similar to that of the SAE 8600 series. This base composition was chosen because it has sufficient hardenability to permit accurate measurement of the times required for transformation to start at various temperatures. The chemical analyses of the steels used in the first part of this investigation are listed in Table I. These steels were made as 200 lb heats in an induction furnace. The furnace charge was Armco ingot iron with the alloying elements added as ferroalloys. After the alloy additions were made, the heat was deoxidized with 0.125 pct Al. A 100 lb ingot was cast and an addition of 0.003 pct B, as ferroboron, was made to the metal remaining in the furnace. This metal was cast into a second 100 lb ingot. The ingots were forged to 11/4 in. diam bar stock from which end-quench hardenability specimens were obtained. Part of this material was further reduced by hot rolling to lx¼ in. bar stock from which specimens were obtained for isothermal transformation studies. Studies of Nucleation and Growth: End-quench hardenability tests were performed on these steels, using an austenitizing temperature of 1600°F. The hardenability curves, shown in Fig. 1, indicate that boron treatment resulted in considerable increase in hardenability of the steels. Any such change in hardenability must result from a change in the transformation rate of the austenite, and these rate changes can be established readily by isothermal transformation studies. Isothermal transformation studies were conducted on these steels as follows: specimens were austeni-tized at 1600°F for 15 min, transferred to a lead bath operating at a constant subcritical or intercritical temperature, held for various lengths of time, and water quenched. The specimens were sectioned for metallographic examination to determine the amount and the type of transformation products present. In order to determine the effect of boron on the formation rate of ferrite, isothermal transformation tests were made on the 0.20 pct C steel in both the boron-treated and boron-free condition at an intercritical temperature of 1375°F where ferrite is the only decomposition product of this low carbon austenite. The results of these tests are shown in Fig. 2, where the percentage of ferrite formed is plotted as a function of time at temperature. It is apparent that boron markedly decreased the transformation rate of austenite to ferrite at this temperature.

Jan 1, 1956

By J. H. Brophy

Experimental evidence in recent years shows that nickel coated hydrogen reduced tungsten powder can be sintered to 98 pct of theoretical density at 1100°C. New data indicate that the sintering rate is the same for nickel contents ranging from 0.125 wt pct (mon-atomic layer) to 5.0 wt pct Ni coated on 0.561. tungsten powder. Nickel tungsten made by coreduction from oxides sinters in a kinetically similar way, but the rate tends to increase with higher nickel contents. The activation of sintering can be accomplished with a minimum amount of nickel if coated powder is used. Transverse rmpture strength was found to increase in specimens containing 0.25 pct Ni as density increased during the initial stage of the carrier-phase sintering process. Upon the onset of grain growth in the final stage, strength was found to decrease. With increasing nickel contents up to 4 pct, strength increased. Maximum strengths in three-point loading were observed at 73,000 psi for 0.25 pct Ni and 93,000 psi for 5 pct Ni. These were comparable to that of massive tungsten recrystal-lized in the presence of nickel and tested in the same way. The results were sensitive to the mode of powder treatment and ductility was negligible in all cases. The study and application of sintered bodies of nickel and tungsten is not new; however, the analysis of the mechanism by which small additions of nickel increase the sintering rate of tungsten promises to Contribute new information regarding sintering theory in general. Initial experimental evidence was presented by the authors showing that nickel-coated hydrogen-reduced tungsten powder may be sintered to 98 pct of theoretical density at 1100°C in 16 hr.' Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the 'solution-precipitationo step postulated when the carrier phase is liquid3 although in the nickel tungsten case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in mi-crostructures at the temperatures under consideration. In the present work, new data for nickel-coated tungsten powder are offered in support of the proposed mechanism, and a more explicit study of the second stage of densification is presented. Concurrently, the sintering kinetics of these coated powders are compared to Ni-W powder made by coreduction of oxides. In this way the present work can be compared to earlier results in nickel activated sintering of tungsten in which the coreduction process was emplyed. The ultimate utility of such an activated sintering process will be determined to some extent by the mechanical and physical properties of the final prod-

Jan 1, 1962

By W. C. Winegard, J. E. Gruzleski

The stages in the development of cells in the Sn-Cd eutectic have been studied by unidirectionally solidifying specimens under known conditions of growth rate, temperature gradient, and impurity concentration. By means of a quenching technique, the shape of the solid-liquid interface during solidification could be observed. Cells are shown to develop from defects or depressions which exist on the solid-liquid interface of even a pure eutectic. Th,e container wall, grain boundaries , and fault lines in the micro structure play an important role in cell development. A two-phase eutectic dendrite found at high impurity concentrations is described. L HE cellular or colony structure formed during eutectic solidification caused much confusion among early workers in their attempts to classify eutectic structure, and a major advance in our understanding of eutectic solidification was made when the colony structure was identified with a cellular interface caused by the presence of impurity elements.1'2 To date, however, no detailed investigation of the stages in cell development in eutectics has appeared, and little work has been done on the cell morphology. The present paper presents the results of such an investigation. EXPERIMENTAL The Sn-Cd eutectic was used in this investigation with lead as the impurity element to promote cell formation. Materials of 99.999 pct purity were zone-refined to an approximate purity of 99.9999 pct. Alloys as close as possible to the eutectic composition, 67.75 wt pct Sn, were prepared using zone-refined tin and cadmium. The alloys were then zone-melted to the exact eutectic composition, as described by Yue and Clark,3 using a total of twenty to twenty-five passes on each eutectic bar. Only those portions of the bars which contained no primary phases were used in subsequent experiments. Master ternary alloys were prepared by melting together the required amounts of lead and the Sn-Cd eutectic in a sealed Pyrex tube under argon, and these alloys were then diluted with pure Sn-Cd eutectic as required. Unidirectional solidification was conducted vertically upward using the two-element resistance furnace shown schematically in Fig. 1. With this apparatus, it was possible to obtain a range of growth rates and temperature gradients so that the cell structure could be studied under different growth conditions. Growth rates in the range of 0.4 to 9.1 cm per hr and temperature gradients from 2.25° to 1475°C per cm were used. To ensure steady-state solidification, power to the furnace was stabilized, and the entire apparatus was enclosed in a large box in which the temperature was controlled to within ± 0.2°C. The apparatus was arranged so that the specimen could be quenched in situ during solidification by pouring a large quantity of water down the central vycor tube. Excellent delineation of the solid-liquid interface at the time of the quench was obtained because of the structural changes accompanying the rapid solidification of the remaining liquid. The quenching rate was always extremely rapid as no evidence of a transition in the lamellar spacing at the interface was ever observed. The alloys to be solidified were contained in degassed, high-purity graphite tubes, 1 cm OD and 0.6 cm ID. The specimens were about 18 cm in length. After the alloy had been cast into the tubes, three 0.8-mm holes were drilled in the tube to the center of the specimen. One hole was placed 1 cm from the bottom of the ingot, and the other holes were placed at 8 and 9 cm, respectively, from the base of the ingot. Thirty-four-gage chromel-alumel thermocouples were sealed in the holes. The lower thermocouple was used to position the solid-liquid interface at the start of each experiment,

Jan 1, 1969

By P. E. Doherty, B. Chalmers

Subboundaries may be revealed in aluminum by the formation of pits on the surface during cooling from elevated temperatures. The pits do not form in the vicinity of high- or low-angle boundaries. They are attributed to the condensation of vacancies from a super saturation produced during coolirzg. Using the vacancy pit and Schulz X-ray techniques for observing low-angle boundaries, a study was made of the transition from the nearly perfect seed to the striated structuke characterist-ic of aluminum crystals grown from the melt. It was found that the individual striation boundaries develop by the coalescence of very small-angle boundaries, as well as by the addition of individual dislocations. Several mechanisms for the formation of striations are discussed. Evidence was found suggesting that a super-saturation of vacancies exists near a growing interface, and it is proposed that the resulting climb of existing dislocalions produces "half'-loops" at the interface, which combine to form the low-angle striation boundaries. LINEAGE, or "striation" boundaries, have been studied in detail by Teghtsoonian and Chalmers 1,2 in crystals of tin grown from the melt, and by Atwater and Chalmers3 in lead. They found that single crystals grown from the melt consist of regions which are separated by subboundaries that lie roughly parallel to the growth direction. A difference in orientation of 0.5 to 3 deg exists between the striated regions; the misorientation is such that the lattice of one region could be brought into coincidence with the lattice of its neighbor by a rotation about an axis approximately parallel to the direction of growth of the crystal. They observed an incubation distance for the formation of striations which increased with decreasing growth rate. They also found that in any crystal, the sum of all rotations of the lattice in one sense, in going from one striation to the next, is very nearly equal to the sum of all the rotations in the opposite sense. A striation boundary, which is a low-angle grain boundary, can be described as an array of dislocations. If it is assumed that suitable dislocations are introduced into the crystal during solidification, the formation of striation boundaries can be explained as a result of the migration of the disloca- tions into arrays. The formation of arrays is energetically favorable since the energy of an assembly of dislocations can be reduced by the interaction of the stress fields when a suitable array is formed. This investigation presents and interprets new information concerning the nature and origin of striation boundaries in aluminum. EXPERIMENTAL TECHNIQUE Single crystals of high-purity aluminum (Alcoa 99.992 pct) were prepared by horizontal growth from the melt.'' The specimens were subsequently electropolished in a solution of 5 parts methanol to 1 part perchloric acid kept between -10° and 0°C in a bath of dry ice and alcohol. The current density was approximately 6 amps per sq in. Doherty and Davis9 have shown that in aluminum sub-boundaries with misorientations of not less than several seconds of arc may be revealed by the vacancy pit technique. During cooling from elevated temperatures pits form on electropolished surfaces of aluminum crystals as a result of the condensation of vacancies.11 Pits do not form in the vicinity of small- or large-angle grain boundaries, presumably because such boundaries act as sinks for vacancies. Boundaries of misorientations down to 3 sec of arc are revealed as pit-free regions, see Fig. 1. The Schulz X-ray technique12 was used to determine the angular misorientations of subboundaries. In this method, white radiation from a micro-focus X-ray tube is used to produce an image of a fairly large area of a single crystal surface. Subboundaries cause splitting in the diffracted image, see Fig. 2. Misorientations down to about 15 sec of arc may be observed with this technique. OBSERVATIONS AND DISCUSSION Figure 1 shows a striated aluminum crystal grown at 10 cm per hr etched by the vacancy pit technique. An incubation distance of about 1 cm is observed before the initiation of striation boundaries. Fig. 2 is a Schulz X-ray photograph of a striated crystal similar to that shown in Fig. 1. A large area of the crystal was studied by means of a series of photographs. Fig. 2, which is a reflection from the (100) plane, included about the first 4 cm of crystal to freeze. There is an incubation distance of about 1 cm, and a distance of about 2 cm over which the angle of misorientation builds up to its final value of approximately one degree. Some twist component can be seen in Fig. 2 at the right side of the photograph. From Fig. 2 it can be seen that the sum of all rotations of the lattice in one

Jan 1, 1962

By M. T. Halbouty

The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.

Jan 1, 1938

By T. M. Broderick

InveStIgations into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attracting increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minnesota (which spends about $80,000 annually on problems of the iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.' Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was outlined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert. About 85 per cent of the iron and steel produced in the United States comes from ores of the Lake Superior district. The reserves of direct

Jan 1, 1935

By R. McNeill, D. E. Weiss, E. A. Swinton

In a continuous countercurrent exchange process, an alteration in any one of the operating conditions has a complex effect on the others, which can only be predicted by employing the transfer unit or the theoretical stage theory on a basis of trial and error. A simple method is described for illustrating diagrammatically the behavior of a counter-current system, the equations being simplified by means of a concept the maximum hypothetical exchange performance. An example based on a typical metallurgical system is given, in which a divalent metal is recovered from a dilute solution, the resin being regenerated continuously by a monovalent ion. Useful conclusions are drawn from a study of the theory. Practical methods for performing continuous ion exchange are discussed, and the development of equipment based on modified ore dressing jigs is described. A swinging sieve jig contactor is evaluated experimentally. DURING the last decade, the new synthetic ion exchange resins have been applied extensively in industries outside the field of water treatment, but there is no record of a continuous counter-current process operating on an industrial scale. Attempts have been made to devise a satisfactory process but many problems remain to be solved. The basic principles of continuous processes will be outlined, as well as the major problems in their operation and the progress made in the CSIRO laboratories toward the development of satisfactory industrial techniques. In the metallurgical field ion exchange resins can be used for various applications such as the recovery and concentration of valuable metals from mine waters,' the regeneration of pickling and plating liquors," the prevention of pollution by waste effluents and the recovery of the constituents from them," and the purification of valuable metals such as the rare earths by chromatographic fractionation on columns of ion exchange resins.7,8 . Turther applications undoubtedly will be found in the field of hydrometallurgy where the use of ion exchange resins would enable direct extraction of the desired metal ion from the filtered leach liquor or the leach pulp. For example, an ion exchange process has been described recently for the extraction of gold from a cyanide leach pulp." A continuous process would have advantages in many applications over the usual process employing a fixed bed and intermittent cycle. In a recovery process, it would yield a product stream of steady purity and concentration, it would waste less water in rinsing, and if the contacting apparatus were efficient less resin would be used, since each portion of the resin would be cycled as soon as it was loaded instead of lying idle until the whole bed was ready for regeneration. A very major advantage is that it would be simpler to control automatically. It is probable that continuous operation will be the key for really large scale applications of ion exchange. The flow sheet of a continuous ion exchange recovery-concentration process is illustrated diagrammatically in Fig. 1. Dilute liquor containing the valuable ion flows through the stripping section countercurrently to a moving bed of resin and leaves after a final contact with freshly regenerated resin. The resin leaves the unit almost in equilibrium with the incoming liquor and then flows to the regenerating unit where it is treated by a slow countercurrent flow of concentrated regenerant solution. The adsorbed ion is displaced from the resin and appears in the concentrated product stream. The resin then must pass through a rinse unit or section where regenerant entrained by the resin is washed back into the regeneration section by water. The regenerated and washed resin is then recycled back to the stripping section. I. Theoretical Operating Behavior of Continuous Ion Exchange Stripping System The simple theory of continuous ion exchange is analogous to that of solvent extraction and other diffusional transfer operations and is governed by the equilibrium relationship, the mass balance, the rates of mass transfer, and the contacting efficiency of the unit. Equilibrium Relationship—The relative affinity of two ions A and B, for a particular resin immersed in their solution, can be expressed by plotting compositions of the solution against compositions which exist in resin in equilibrium with those solutions, i.e. C/Co vs q/a where C, is the total normality of the solution, C is the normality of ion A in the solution, a is the total exchange capacity of the resin in gram equivalents

Jan 1, 1956