Search Documents

By I. Tamura, J. O. Brittain, T. Mura

Plain carbon steel in the cold worked or marten-sitic conditions has an internal friction peak at about 250 oC at a frequency of I cps. The influence of substitutional alloying elements on this peak was examined experimentally. The alloys were vacuum melted Co-, Cr-, Mo-, Ni-, and Si-iron (about 3 pct alloying elements), and carburized Si-iron. The internal friction of the alloys in the temperature range 30o to 500 OC was determined by means of a torsion pendulum. The 250 oC peak of the cold-worked alloys was lower in height than that observed in plain C-iron and steel. Carburized Si-iron in the quenched condition had a peak which occurred at a slightly lower temperature than in quenched plain C-steel, but the height of the peak was substantially greater than that found for the same alloy in the cold-worked condition. The activation energy of this peak for martensitic Si-steel was about 35 kcal per mol. ANNEALED a iron has two internal friction peaks due to nitrogen and carbon at 20o and 40o C respectively, at a frequency of 1 cps. If a iron is cold worked, these diffusion peaks become smaller and a new peak appears at about 250o C. The activation energy for the 250o C peak is in the range of 32 to 44 kcal per mol and has an average value of 38 kcal per mo1. It has been experimentally verified that both interstitial solute atoms and dislocations are necessary for the 250o C peak. 3 Wert has also shown that an incubation period precedes the appearance of the 250 C peak.4 With regard to quenched martensitic steel, Ke et al.596 observed two peaks at around 130o and 250o C. They conjectured that the 250o C peak in martensite was due to the same mechanism as the 250°C peak in cold worked a iron, and the 130°C peak was due to the nature of tempered martensite. They did not report the activation energy for these peaks. Chernikova7 found only one peak at about 200° C in tempered martensite. In a previous paperS we reported an activation energy of approximately 40 kcal per mol for the 250° C peak in plain carbon martensitic steels. Ichiyama8 found the activation energy to be about 36 kcal per mol for the 250° C internal friction peak in steels in the martensitic condition. The present authors proposed a theory for the 250°C peak for cold worked and quenched iron and steel.= The theory for the peak is based upon the addition of a strain-energy term to the free energy for the formation of a carbide precipitate due to the presence of a disclocation. The model employed for the relaxation process consists of the growth and solution of a carbide precipitate of critical size as a consequence of an oscillating dislocation. In this report, the influence of substitutional alloy ing elements on the 250° C peak is examined and the experimental results are discussed in terms of our theory for the peak. Most of the experimental work on the alloy steels was confined to the Fe-Si-C alloys.

Jan 1, 1962

By Robert E. Green, Edmund G. Henneke

Expressions are derived for the orientation factors associated with dislocation damping due to dislocation motion in the basal slip plane. The results of the calculation of these factors for zinc crystals aye pvesepzted and the relevance of these results to ultvasonic-attenuation measuvements is discussed. In this paper expressions are derived for the orientation factors associated with damping of sound waves due to dislocation motion in the basal slip plane of hexagonal crystals. For zinc crystals, the orientation factors for dislocation motion in one slip direction only, as well as for simultaneous motion in all three basal slip directions, have been calculated at 1-deg intervals. The results of these calculations are presented in the form of contour diagrams in a sector of a standard polar coordinate graph. The calculations have been carried out for both the traveling- and the standing-wave conditions. The relevance of these results to ultra sonic-attenuation measurements is discussed. Associated with the calculation of the orientation factors, the modes of elastic-wave calculation were also evaluated, according to the procedure previously employed by Hinton and Green.' The results of these calculations are not presented here since similar results have been reported earlier by Mus-grave.2 However, it should be mentioned that, although the qualitative features of Musgrave's results are preserved, the quantitative values are somewhat altered since different values for the elastic constants of zinc were used. ORIENTATION FACTORS It is convenient to refer to three different sets of coordinate axes, Fig. 1, in the following calculations. First, there are the Miller-Bravais axes which are used in describing the Miller-Bravais indices of planes and directions in a hexagonal crystal. These axes are denoted in the conventional manner by a,, a,, a,, and c. The second set of axes used is a rectangular Cartesian coordinate system located as shown in Fig. 1. Note that the x axis coincides with the close-packed direction al [2110], the z axis coincides with the c axis [0001], and the y axis is orthogonal to these two lying in the [0110 ] direction. Finally, a form of Eulerian angles is used to locate the position of the specimen axis. The angle between the specimen axis and the c axis is denoted by 0 and the angle between the projection of the specimen axis on the basal plane and the a, direction is denoted by ø. The majority of observations on plastic deformation of metal crystals indicates that such deformation is caused by the motion of dislocations on a limited number of crystalline planes and in a close-packed direction. In crystals with hexagonal symmetry the most prominent slip plane is the basal plane (0001) and the slip directiops- are one of the close-packed directions, [2110], [ 12101, or [ 1120]. To properly set the stage for the following work, several points must be clarified. First, we want to consider the contribution to the attenuation of elastic waves by dislocations only. While the Granato-Lucke, model for dislocation damping is presently the one most quoted, it is not necessary to refer the present work to it. The only assumption that need be made is that the motion of dislocations absorbs energy from the elastic wave and therefore attenuates it. It is immaterial here how this energy absorption occurs. However, because dislocations have been observed to move most freely on the (0001) plane for hexagonal crystals undergoing plastic deformation, it will be assumed that it is the dislocation motion on this plane which attributes to the observed attenuation. The basic orientation factor, Ok, is essentially the same as that used by Green and Hinton for fee crystals,4 defined by the equation

Jan 1, 1968

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,' through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By D. L. Albright, R. W. Kraft

Solidification experiments were conducted with the objective of testing the theory of eutectic colony formation. Appropriate control of variables in tests on a series of high-purity aluminum-copper specimens of eutectic composition resulted in the observation of three types of eutectic microstructures, these being a unique structure consisting of lamellae essentially parallel to one another, a banded structure, and the colony structure. Lamellar faults, which are morphologically similar in many respects to edge dislocation models in crystals, produced a complex substructure in these specimens. SOLUTE rejection at the advancing solid-liquid interface of a unidirectionally solidified single-phase metal can cause the liquid immediately in front of the interface to become constitutionally super-cooled below the equilibrium liquidus temperature. Constitutional super-cooling occurs if the solidification rate, R, is too rapid, or if the thermal gradient in the liquid at the interface, G, is too low. 1 This constitutionally supercooled layer in turn stabilizes a cellular rather than a planar interface.&apos; A similar cellular interface has been observed when lamellar and other types of eutectics were unidirectionally solidified, and it has been shown that the cellular interface led to the formation of eutectic colonies.&apos; The lamellar structure is fan-shaped at the edges of colonies (which correspond to valleys or grooves in the cellular interface) because the lamellae grow normal to the local interface. One of the possible mechanisms which might cause the formation of the cellular interface, in the case of solidifying eutectic alloys, is constitutional supercooling of the liquid with respect to a third component rejected by both phases of the eutectic.3,4 On the basis of the analogy between the solidification of single-phase metals and binary eutectics, a eutectic alloy should solidify with a planar interface if the ratio of G/R is sufficiently high to compensate for any impurity which might be present and causing constitutional supercooling. The fan-like microstruc-ture of eutectic colonies should not occur under these conditions and the lamellae should be parallel to one another and to the solidification direction for extended distances. The experiments conducted in this investigation were designed to test these ideas. Following a resume of the experimental procedure, the various microstructures observed during the study are described, and their relationship to the growth conditions which produced them is discussed. EXPERIMENTAL PROCEDURE The eutectic between an aluminum solid solution and 0 phase (approximate composition CuA12) was chosen for this work for the following reasons: it was known that a lamellar structure forms, the eutectic temperature is low enough to facilitate experimental work, and the components can be procured commercially in a very pure form. High-purity copper (est. 99.999 pct Cu, obtained from National Research Corp.) and spectrographic aluminum rods, having impurities other than copper estimated to be Zn-15 ppm, Mg-10 ppm, Fe-3 ppm, Na-2 ppm, Cd-1 ppm, and Mn < 1 ppm, were melted in a stabilized zirconia crucible in a vacuum induction furnace at a pressure of 10 pof Hg. The melt was superheated to about 1000°C to assure mixing, cooled to 780°C and cast into an investment mold which yielded sixteen cylindrical specimen blanks 1/2 in. in diam and 5 1/2 in. long. The casting was allowed to solidify under vacuum. This master heat had an analysis of 32.6 wt pct Cu and 67.4 wt pct A1 by difference. The cylindrical specimen blanks were remelted and solidified unidirectionally in an apparatus illustrated schematically in Fig. 1. An RF induction coil heated

Jan 1, 1962

By T. Y. Yan

SUMMARY Laboratory high pressure column tests have shown that the presence of 1-20 ppm of aluminum ion effectively prevents permeability loss during uranium leaching with leachates containing sodium carbonate. If added after permeability loss has occurred, aluminum ion can restore the permeability to nearly its original value. No deleterious effect was observed on uranium leaching performance and the technique should be quite compatible with all field operations. INTRODUCTION The recovery of uranium values from underground deposits by in situ leaching or solution mining has become economically viable and competitive with conventional open pit or underground mining/milling systems (Merrit, 1971). In situ leaching processes are particularly suitable for small, low-grade deposits located in deep formations and dispersed in many thin layers. Many such ore bodies occur along a broad band of the Gulf Coastal Plain (Eargle et. al., 1971). The advantages of the in situ leaching processes have been reviewed (Anderson and Ritchi, 1968). In the in situ leaching process, a lixiviant containing the leaching chemicals is injected into the subterranean deposit and solubilizes uranium as it traverses the ore body. The pregnant lixiviant or leachate is produced from the production well and is then treated to recover the uranium. The resulting barren solution is made up with the leaching chemical to form lixiviant for re-injection. Upon completion of the leaching operation, the formation is contaminated with leaching chemicals and other species made soluble in the leaching operation and has to be treated to reduce the concentration of these contaminants in the ground water to levels acceptable to the regulatory agencies (Witlington and Taylor, 1978). Restoration is accomplished by injecting a restoration fluid, which could be the fresh water or water containing chemicals, into the formation. As it traverses the leached formation, the restoration fluid picks up the contaminants and is then produced at the production well. This produced water is either disposed or purified for recycle. In both phases of operation, formation permeability or well injectivity is one of the most important parameters which determines the viability of the in situ leaching process. Low formation permeability limits production rates, leading to uneconomical operations. The formation is said to be sensitive if there is a sharp loss of permeability on contact with water and other fluids. Many uranium bearing formations, for example, the Catahoula formation of the Texas Coastal Plain, contain significant amounts of clay minerals which are water sensitive. Serious permeability losses can occur when the pH and chemical composition of the lixiviant is significantly different from that of the formation water. Jones has investigated the influence of chemical composition of water on clay blocking of permeability (Jones, 1964) and Mungan studied permeability reduction through changes in pH and salinity of the water (Mungan, 1965). Various mechanisms of permeability damage have been proposed and reviewed (Jones, 1964; Mungan, 1965; Gray and Rex, 1966; and Veley, 1969). When large amounts of swelling clays are present, a significant fraction of the flow channels in the formation can be reduced due to swelling. However, in most cases, swelling need not be the main cause of permeability losses. Particle dispersion and migration or clay sliming can be more important causes for formation damage. Clay particles entrained in the moving fluids are carried downstream until they lodge in pore constrictions. As a result, microscopic filter cakes are formed by these obstructions, plugging the pores, effectively restricting fluid flow and reducing the formation permeability. Moore found that as little as 1-4 percent clays present in a fine grained sandstone could completely plug the formation if they are contacted by incompatible injected fluids (Moore, 1960). It has been found that injection of NaHC03/Na2CO3 lixiviant into formations with significant clay content often leads to loss of formation permeability and well injectivity. To alleviate this problem a change of the lixiviant composition to KHC03/K2CO3 has been proposed. At present, however, many in situ leaching operations employ NH4HC03/(NH4)2C03 mixtures as a source of carbonates. This approach has been successfully used in South Texas by Mobil, Intercontinental Energy, Wyoming Minerals and U.S. Steel, etc. The use of ammonium carbonates solutions, however, contaminates the formation and requires a time-consuming restoration operation. The other approach to reduce the permeability loss is to pretreat the sensitive formation with chemicals which prevent clay dispersion and migration. Such chemicals include hydroxy-aluminum (Reed, 1972 and Coppel et. al., 1973), hydrolyzable zirconium salts (Peters and Stout, 1977), hydrolyzable metal ions in general (Veley, 1969) and polyelectrolyte polymers (Anonymous). Still another approach, is to minimize the "shock" caused by sudden injection by gradually changing the chemical composition of the injected fluids from that of the formation water. THE APPROACH Since permeability loss can be an important factor limiting the efficiency and economic viability of the in situ leaching process, a study was initiated on

Jan 1, 1982

In traversing lately the Sierra Madre, west of Sail Pedro and Guanacevi, I estimated the topographic summit at several points, by aneroid barometer, at about 8,500 ft. Mr. Weed&apos;s measurements, 40 miles further north, are from 9,000 to 9,500 ft., and indicate the correctness of the impression I obtained at the time, namely, that the greatest movement in the elevation of the Sierra was between Guanacevi and Guadaloupe y Calvo. This is suggested also by the course of the headwaters of the Rio Conchas and of the Nazas, and by the relative corrasion of the branches of the two streams. Mr. Weed&apos;s statements as to the unevenness and great relief of the andesite floor underlying the later dacites and rhyolites are very interesting, and lead me to add that the floor of the andesite breccias and flows is uncovered for several square miles east of Guanacevi. This floor is of reddish, bluish and gray shales, lying horizontal or dipping slightly east. Their age is unknown; but from the interbedded occurrence of copper sulphides, I took it to be Triassic,

Jan 1, 1903

By A. Mitchell

An approximate phase diagram has been developed for the CaF2-CaC2 system, indicating a eutectic point at 1240°C, Ncac2 = 0.13, and no detectable solid solution in either phase. The liquidus line is shown to correspond to a simple c22- ion in solution. A thermo-chemical study of&apos; the reaction between carbon-saturated Ni-Ca alloys and CaC2-CaF2 liquids indicates that lhe Raoullian activity coefficient of CaC2 in dilute solution in Cap2 al 1500°C lies between 8 and 10. Some effects of the stabilily of Cap2-CaC2 solutions at high temperatures on electroslag remelting praclice are outlined. THE alkaline earth acetylides. MIIC2, have a reasonably high thermochemical stability at high temperature in the solid state,&apos; with the exception of magnesium, which forms an unstable acetylide at low temperatures (-500°C) and a carbide, Mg2C3, in the range 700&apos; to 1000°C. The acetylides of calcium and barium have been shown to have limited solubility in their respective chlorides,&apos; and further these solutions contain the acetylide as a C: ion.&apos; The equivalent magnesium solutions have not been studied. Although calcium "carbide" is used as a desulfuriz-ing reagent in steelmaking. and is possibly present as an acetylide-oxide phase in very basic electric arc practice slags, the acetylide ion appears to be substantially unstable in a silicate slag.* As a conse- *This instability arises from equilibria in the reaction: CaC2 + CO = (Ca0) + 3C where the low intrinsic solubility of CaC2 in silicate lattice, and the low activity of CaO in a silicate solution where CaO/Si02 < 1, combine to give a very small equilibrium concentration of CaC2 in solution in such silicate slags at temperatures in the region of I 500°c, even under carbon-saturated conditions. Under highly basic conditions, a liquid CaO-CaC2 phase may separate from the silicate system quence of this, the possibility that reactions involving CaC2 in silicate solutions are of importance to general steelmaking practice is remote. However, in operations involving a slag primarily based on a halide, or alkaline earth oxide, we must take into account the possibility that CaC2 will appear in quantities sufficient to significantly affect both the chemical and physical properties of the slag. The work outlined below presents a study of the CaF2-CaC2 system intended to provide sufficient data to allow an estimate of the importance of this system to electroslag remelting and welding practice. However, we should indicate at this point that there will be other processes, e.g., heat treatment, flux cleaning of castings, fused salt electrolysis, and so forth, where alkaline-earth halide fluxes are in contact with carbon, graphite, or carbides, and where halide-acetylide solutions must be taken into account. EXPERIMENTAL 1) Structural Studies. In view of the difficulty ex-perienced in handling CaC2 prepared from calcium turnings and propane gas at 700°C, it was decided to use solutions prepared directly in the equilibration apparatus, Fig. 1. The starting materials were: a) Ni-Ca-C alloy, prepared by adding calcium to liquid nickel held under calcium fluoride in an induction-heated graphite crucible; b) calcium fluoride, prepared by fusing calcium fluoride powder (British Drug House "EXTRA PURE") calcium fluoride in an induction-heated graphite crucible, in air, followed by electrolysis between graphite electrodes at 1 amp cm-2 density, for 10&apos; coulombs per g CaF2. This procedure decomposes the CaO produced by hydrolysis during the fusion step, replacing it by CaC2; Ca2+ + 2e-Ca*(l) Ca*(l) + 2C(gr)-(CaC2)caF2 O2- -2e-O*(g) O*(g) +C(gr)-CO(g) This results in a composition of between 2 and 5 wt pct CaC2 in CaF2. Fifty grams (in lumps) of this material were placed in a graphite crucible, together with Ni-Ca-C alloy (averaging 20 wt pct Ca), and the equilibration apparatus assembled. The alloy reacted with the crucible at high temperature to give CaC2, which dissolved in the calcium fluoride solution to give the desired composition. Cooling curves were plotted manually for these liquids, with rapid stirring and CaF2 seeding to minimize supercooling, and using a Pt/Pt 13 Rh thermocouple calibrated on the freezing points of nickel and copper. This gave a reproducibility of ±0.l°C. and an absolute accuracy of the thermocouple of ±l°C. An example curve is shown in Fig. 2, with the CaF2 end of the binary system in Fig. 3. The CaF2-CaC2 ingots were crushed, under dry nitrogen, and sampled for chemical analysis and X-ray examination. Analytical details are given in the Appendix. Powder diffraction data indicated that the only phases present in all samples examined were calcium fluoride and tetragonal (Types I and 111) calcium acetylide,4 with no evidence of solid solutions or compound formation. 2) Thermochemical Studies. The apparatus used to obtain activity data on CaC2 in these systems is shown in Fig. 4. It consists of an arrangement whereby the graphite crucible and its contents (CaF2-CaC2. Ni-Ca-C) can be rapidly cooled without exposure to air. Trial experiments to determine an equilibration time by ap-

Jan 1, 1969

By R. E. Barnes

An overall view of the perlite industry is concisely presented. The geology, mining, milling, processing, and applications of perlite, as well as the present status of the perlite industry are treated. Perlite, in strict petrological usage, describes a specific variety of volcanic glass in which strain, incident to cooling, yielded a concentric structure of fracturing which may be visible either to the naked eye or under a microscope. In commercial usage, the term perlite includes any naturally occurring acidic glass of volcanic origin that will expand when heated to a suitable temperature. The name perlite is a derivation of perlstein which originally defined "certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."1 While perlite has been known to geologists for many years, it was not until 1941, while investigating perlite for use in enamel, that an assayer in Superior, Ariz., noted the unusual expansion characteristics of the ore. Further investigations were delayed until following World War II when many small plants were built and experimentation in the treatment and uses of perlite began. The Perlite Inst. was organized in 1949 to promote the development of the new industry, establish commercial standards through research, and to explore new uses and markets. The Institute, located in New York, represents some 50 producers in the U.S., Canada, Australia, England, France, Germany, Greece, Japan, Mexico, and New Zealand. In 1949, 71,l002 short tons of crude perlite were produced, sold or used by U. S. producers, and this figure increased to 325,0003 short tons by 1959. Such a rate of increase indicates the rapid and continuing growth of the perlite industry. GEOLOGY Perlite ore in its crude form has been found in seven of the mountainous western states, since un-devitrified siliceous volcanic rocks are limited to this section of the U. S. Commercially operated perlite deposits are normally of Eocene and Oli-gocene age.4 These deposits are often several hundred feet thick and may extend over hundreds of acres. In 1959, 13 companies in six states produced crude perlite, although the output in New Mexico comprised 79 pct of the total domestic crude output. Other states in order of their production were: Nevada, Arizona, California, Colorado, and Utah.5 Foreign deposits of perlite which are either producing or under exploration are Australia, Canada, Greece, Hungary,6 Iceland, Ireland, Japan, Mexico, New Zealand, and Sardinia. The ore may exhibit a variety of characteristics depending partially on its water content and eruption history and may range through many shades from black to white. While these characteristics may vary slightly among deposits, perlite ore from a particular source is normally quite uniform. Available chemical analyses of perlites from a large sampling of domestic deposits were recently assembled by the Technical Committee of Perlite Institute and are presented in Table I. While the ranges given do not apply to a particular perlite, they are an indication of the chemical analysis which may be expected from any presently commercially operated deposit. The specific gravity of the perlite ore ranges between 2.2 and 2.4, and its bulk density when crushed and sized is 75 to 90 Ib per cu ft. MINING AND MILLING Perlite ore is quarried from open pits by conventional power equipment, although blasting has been occasionally employed. The rock is then stock-piled until needed. While the milling of perlite may seem a simple process compared to that required for basic metals, or even other nonmetals, the need for accurate control of particle size becomes extremely important in further processing. The first step in this operation is the primary crusher, which is normally a jaw crusher. Following crushing, the material is dried, if necessary, in a rotary dryer and conveyed to a secondary grinder which may be a rod mill, hammer-mill, or cone crusher. However, the crushing characteristics of the perlite, caused by incipient cooling fractures, requires it be removed from the grinding operation once it is reduced to the required size so as to prevent overgrinding. Following the grinding operations, various size screens are used to separate the ore according to particle sizes required for particular uses. Most plants use two or more stages of crushing with perhaps four stages of screening.

Jan 1, 1961

By A. L. Titchener, M. B. Bever

The stored energy of cold work was investigated in drawn gold-silver wires by tin-solution calorimetry as a function of strain, strain rate, initial grain size, and temperature of defornation. The energy expended in the deformation process was measured. Hardness was also measured and was correlated with the stored energy as a function of strain and strain rate. Mechanisms of energy storage are discussed. THE variables which determine the amount of energy stored in a metal during cold work are of two kinds: those involving the metal and its condition and those involving the process of deformation. For example, the stored energy differs between one metal and another and between different degrees of purity of a single metal. It also depends on the nature of the deformation process and particularly the extent, rate, and temperature of deformation. Most investigators have reported the stored energy as a function of strain (or some similar geometric parameter) or of the energy expended during deformation. In general the stored energy increases with strain, rapidly at first, but more slowly at large strains until a saturation level is reached. Information about the effects of other variables, however, is limited. Some data are available on the dependence of the stored energy on the purity of a metal1 and on the composition of

Jan 1, 1960

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By R. Webeler

In order to study the role of work hardening in the fatigue process, use was made of the great sensitivty of the resistivity of AuCu to cold work. A change of the resistivity of AuCu of the order of 1 to 2 pct at the temperature of liquid nitrogen was found to occur as a consequence of severe fatigue. ACCORDING to Orowan&apos;s theory,&apos; the process of fatigue In metals 1s associated with the production of a number of small regions which have undergone strain hardening. This phenomenon is supposed to occilr even if the stress applied during fatiguing is always smaller than the yield stress. In an attempt to verity the existence of such regions, Welber and Webeler&apos; undertook to detect the stored energy associated with severe fatigue in copper. Previous experiments" had shown that the energy stored in a sample of copper which has been cold worked by torsion is released in the temperature range between 150" and 250°C when the sample is heated from room temperature and that no more energy is released (or absorbed) between 250" and 450°C. In particular the stored energy amounted to 0.41 cal per g for a case in which the mechanical energy expended in twisting the sample was 11.9 cal per g. In the case of fatigued copper, however, no release of stored energy could be detected between 150" and 250°C, so that the experimental error of &0.02 cal per g represents an upper limit for the amount of energy stored in strain hardening., It seemed desirable to attack the problem in a new fashion. For this purpose, it was decided to make use of the fact that, if an alloy capable of undergoing the order-disorder transition is ordered and then cold worked, the resistivity, p, increases very greatly above the value for the ordered state even if the deformation is very small. Some insight into the nature of the fatigue process may be obtained then by measuring the resistivity of an ordered sample before and after subjecting it to fatigue. For reasons which will become apparent from the following remarks, considerably more can be learned by carrying out the resistivity measurements at two different temperatures. In the case of a material containing impurities, vacancies, dislocations, or other imperfections of essentially atomic dimensions, the resistivity, p, according to Matthiessen&apos;s rule, can be represented as a sum of two terms p = p, + p, where p, is the (temperature dependent) resistivity of the pure metal, and p, is the temperature independent contribution of the imperfections. Briefly, the physical basis for this rule is the following: The main contribution of the impurities in question to the resistivity results from the fact that they interrupt the periodicity of the lattice and thus scatter the conduction electrons with a probability which is almost independent of temperature. In order that this be the case, it is necessary that the&apos; extension of the impurities be small enough—roughly less than one electron mean free path—so that their main effect on the resistivity occurs for the foregoing reason. If an alloy like AuCu is partly or completely disordered by quenching from an appropriate temperature, Matthiessen&apos;s rule also applies to a very good approximation* with p, representing in this case the resistivity po of the ordered sample and p, the additional (temperature independent) resistivity due to the disorder. In general, the disorder can be represented in terms of atoms which are displaced from their "proper" positions in the superlattice and which thus qualitatively represent the imperfections in the superlattice responsible for the term p,. Since the misplaced atoms are distributed at random throughout the super-lattice, their contribution to the resistivity still can be considered in terms of the scattering of conduction electrons by lattice defects. The situation is somewhat more complex in the case of an alloy disordered by cold work because the process of disordering here does not involve a random redistribution of the atoms; however, Matthiessen&apos;s rule also holds in this case. Whenever Matthiessen&apos;s rule does apply, the values of the quantity /3 = (p? — /(T, — T,), where p, and p, are the values of the resistivity at two fixed temperatures, T, and T,, respectively, is constant (independent of p,) for a given alloy or metal. In particular, if a sample of AuCu is subjected to ordinary cold work, the value of /3 remains equal to Po, the value for the ordered material. According to Orowan&apos;s theory,&apos; as remarked before, a fatigued sample contains a large number of isolated severely cold-worked regions, which make up only a small proportion of the metal. Thus, if a sample of AuCu initially in the ordered state is fatigued, more or less disordered regions will be produced within the ordered material. If these regions are small enough so that Matthiessen&apos;s rule applies, then it follows from the previous discussion that /3 again will remain equal to Po. If the effect of fatigue is to produce cold-worked regions which are macroscopic—of the order of at least several electron mean free paths—the effective resistivity, p, has to be computed by use of the ordinary laws of large-scale electrodynamics. For the sake of simplicity, it will be assumed here that the cold-worked regions are completely disordered and have a resistivity, p,. For a given proportion A of disordered regions the effective resistivity, p, for the current in a given direction depends on the geometrical configuration of these regions. In any case, the value of p for such

Jan 1, 1956

By D. V. Edmonds, C. J. Beevers

Tensile tests were carried out on a! titanium containing 850, 1250, and 2700 ppm 0, and up to -500 ppm H. The tests were performed at -196", -78", 20°, 150°, and 300°C at a strain rate of -1.0 x 10??3 sec-1. Increasing oxygen content, increasing grain size, and decreasing test temperature resulted in enhanced embrittlement of the a titanium by the hydrogen additions. Metallographic observations showed that this can be correlated with the influence of these parameters on the introduction of cracks into the a! titanium by fracture of titanium hydride precipitates. CRAIGHEAD et al.1 reported that the hydrogen content normally found in commercial-purity a! titanium (60 to 100 ppm) was sufficient to cause a substantial lowering of the impact strength, and they attributed this embrittling effect of hydrogen to the precipitation of titanium hydride. Lenning et al.&apos; found that in commercial-purity a titanium there is an almost complete loss of impact strength at about 200 pprn H, which is approximately half the value needed to eliminate the impact strength of high-purity a titanium. They also showed that the presence of 3000 ppm hydrogen reduces the room-temperature tensile ductility of commercial-purity material to a value of the order of 10 pct; the corresponding hydrogen concentration for high-purity titanium is over 9000 ppm. It thus appears that the detrimental effect of hydrogen on the mechanical properties of commercial-purity titanium becomes evident at much lower hydrogen contents than for high-purity titanium. The main difference between the two types of a titanium might be expected to be the higher level of interstitial impurity in the commercial-purity grade. Jaffee et a1.3 studied the influence of temperature and strain rate on the hydrogen embrittlement of high-purity and commercial-purity ! titanium. In general, the behavior was the same for both materials; embrittlement was enhanced by decreasing temperature and increasing strain rate. Recent results from tests on commercial-purity a titanium containing 850 ppm O and varying amounts of hydrogen up to -500 ppm showed that the degree of embrittlement by hydrogen is intimately related to the fracture characteristics of titanium hydride precipitates.4 The present paper considers the interrelationship between the mechanical properties and micro-structural features of commercial-purity a! titanium containing 850, 1250, and 2700 ppm 0 and varying amounts of hydrogen up to -500 ppm. 1. EXPERIMENTAL PROCEDURE Three types of commercial-purity titanium supplied by IMI* were used in the investigation, and for the *Address: Witton, Birmingham 6, United Kingdom. purpose of this paper are designated Ti 115, Ti 130, and Ti 160. The principal impurity elements are given in Table I. The material was received in the form of 12.7 mm diam bars having a fully recrystallized structure. Tensile specimens with a round cross-section of 4.5 mm diam and a gage length of 15.2 mm were machined from the bars. In order to develop the same grain size (mean linear intercept of grain boundaries) in each of the three types the specimens were annealed under a dynamic vacuum of <10?5 mm Hg, Table 11. Specimen hydriding was carried out in a modified Sieverts apparatus;&apos; hydrogen was taken into solution at 450°C and after holding the specimens at this temperature for 24 hr they were furnace-cooled to room temperature at an average rate of -100 C deg per hr. By this method nominal hydrogen contents of 0, 50, 100, 250, and 500 ppm were introduced into specimens of Ti 115, Ti 130, and Ti 160 (100 ppm (wt) -0.5 at. pct). The actual hydrogen contents were calculated from the weight differences obtained by weighing the specimens before and after the hydriding treatment. Tensile tests were carried out at temperatures of -196", -78", 20°, 150°, and 300°C on a 10,000 kg In-stron machine at a nominal strain rate of -1.0 x 10-3 sec-1. Fractured specimens were sectioned in planes parallel to the tensile axis, mechanically polished to 0.25 µm grade of diamond paste, and then attack polished using a solution containing by volume 99 parts H2O, 1 part HF, and 1 part HNO3. Although the latter treatment unavoidably opened out cracks and voids visible after mechanical polishing, it did reveal the grain structure, titanium hydride morphology, and deformation twinning structure.

Jan 1, 1970

By Thomas H. Leggett

IN speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining-practice, since this has been already well described both in the Transactions1 and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a. whole, marking its general development and the lines of its future progress. In a. paper entitled Deep-Level Shafts on the Witwatersrand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,3 presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (1:). 975): "In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discussed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy was vitally necessary for both 1 Gold-Mining in the Transvaal, South Africa, John Hays Hammond, xxxi., S17 to 855 (1901). R Engineering and Mining Journal, vol. lxxxv., p. 53 (1908). &apos; Trans., xxx., 947 to 987 (1900).

Jan 5, 1908

By A. Y. Bethune, W. G. Woolf

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process&apos; for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt&apos;s earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.&apos;s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By L. D. Mullins, E. B. Elfrink, W. L. Wahl

In the past few years several articles and papers presenting results of solution gas-drive depletion calculations have appeared in the lit-erature. Such calculations are of interest to the oil industry, for investment decisions must often be made before much is known about a reservoir. At other times, an estimate of the possible benefits to be realized from alternate production methods is desirable, and theoretical depletion calculations can serve as a floor or reference level from which to work. In any case, an estimate of ultimate oil recovery based upon engineering data is commonly required. An engineer confronted with the problem of obtaining, for a specific reservoir system, an estimate of ultimate oil recovery by solution gas-drive depletion usually will be forced to perform the calculations himself. This is despite the quantity of data in the literature. Rarely will either experience or the literature provide results from a reservoir system similar in all important respects to the one under consideration, and calculated results are not so plentiful that satisfactory interpolation procedures can be devised. Performing the calculations, however, is a tedious, time-consuming task unless an electronic computer is available, and, in practice, time and manpower are not always available for this purpose. A quick, simple, consistent method was needed for reducing the uncer- tainty in estimated oil recovery from solution gas-drive reservoirs when only minimum information about the reservoir system is available. PROCEDURE Method of Calculation The usual requisite assumptions were made so that the material balance equation could be used to calculate data for the charts. The following assumptions were made: (1) the reservoir is homogeneous and isotropic; (2) oil recovery is due entirely to solution gas drive and neither a gas cap nor a water drive nor gravity drainage is present; (3) the initial reservoir pressure is the bubble-point pressure of the reservoir fluid; (4) initial total liquid saturation is 100 per cent of pore space; (5) interstitial water saturation remains at the initial value as the reservoir pressure declines from the bubble-point pressure to atmospheric pressure; (6) equilibrium gas saturation is 5 per cent of pore space; and (7) oil and gas saturations are uniformly distributed throughout the reservoir at all times. There are no saturation gradients due to a wellbore, nor is the geometry of the reservoir system considered. The material balance equation was written in the form of a differential equation&apos; which was integrated to determine the change in oil saturation for an assigned pressure drop. Formal integration was not possible, so recourse was made to the Runge-Kutta method&apos; of numerical integration. All computations were performed on IBM equipment. Numerical integration yielded the change in oil saturation within the reservoir as the pressure. declined from the bubble-point pressure to atmospheric pressure. The initial oil saturation minus the change in oil saturation yielded the oil saturation at atmospheric pressure. The oil originally in place was obtained by dividing the initial oil saturation by the initial formation volume factor (differential liberation) while the oil in place at atmospheric pressure was obtained by dividing the final oil saturation by the formation volume factor at atmospheric pressure. U1timate oil recovery, expressed as a percentage of the initial oil in place, was obtained by dividing the difference between the oil initially in place and the oil in place at atmospheric pressure by the oil initially in place and multiplying by 100. PVT Data Charts were based upon 135 solutions to the material balance equation. PVT properties of the reservoir fluids were variables in this equation and had to be known as functions of pressure. The required PVT data might have been obtained from either actual reservoir fluid systems or correlated data. However, correlated PVT data were developed and employed in the calculations for the following reasons: (1) it is doubtful that 135 sets of PVT data could have been obtained for the values of variables investigated in this study, and (2) results of recovery calculations from randomly obtained PVT data could not be correlated as well as rssults from selected PVT data. The PVT data used to develop the

By J. A. Hren, C. M. Wayman

RECENT investigators have noted anomalous behavior in the electrical resistivity of vanadium below room temperature. Rostoker and Yamamoto1 in studying the vanadium-oxygen system hypothesized that the body-centered-tetragonal phase existing from 15 to 34 at. pet O at approximately 800°K was really a low-temperature allotrope of vanadium that was stabilized by oxygen. In measuring the electrical resistance of cold-swaged vanadium rod over a range of temperatures, a small discontinuity was observed at approximately 240°K, supporting their notion of allotropy. However, the magnitude of the observed discontinuity was extremely small. Loomis and Carlson2 in studying the ductile-brittle transition in vanadium also made resistance measurements and reported a discontinuity near 200°K. More recently, White and Woods3 showed that the electrical resistivity from room temperature to approximately 100 °K was not linear and at variance with the Bloch-Griineisen law. Instead of finding a discontinuity, they observed a deviation from linearity below 200°K. In discussing their results they pointed

Jan 1, 1961

By W. G. Woolf, A. Y. Bethune

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process&apos; for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt&apos;s earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.&apos;s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By C. B. Alcock, L. I. Cheng

By the use of radiochemical methods for the study of the gas-liquid equilibria at low temperature, and for the determination of the sulfur contents of metal beads which had been equilibrated with H2S/H2 mixtures of known sulfur potential, it has been possible to obtain the liquid solubility and the free energy of solution of sulfur in liquid tin and lead at temperatures between 500°and 680°C. THE gas-liquid equilibrium method has proved in the past to be most successful in the determination of the thermodynamic behavior of dilute solutions of sulfur in liquid metals.1,2 One of the basic requirements for success with this method is that the volatility of both the metal and its lowest sulfide should be small, otherwise sulfide will be deposited at the cool end of the furnace, where it may react with the outgoing gases to form either sulfur-rich lowest sulfide or higher sulfides. The resultant value of the apparent equilibrium constant will then be lower than the correct one. This argument applies even at sulfur potentials below that in equilibrium with a separate condensed phase of the lowest sulfide at the reaction temperature, T. The mass of sulfide which is deposited at the cold end of the furnace, and hence the extent to which further reaction occurs with the outgoing gases, depends on the time taken for equilibrium to be reached between metal and gas. Since this will depend principally on the bulk of the metal phase which is used, one should clearly attempt to uie as small metal samples as possible. These considerations are important in the study of dilute solutions of sulfur dissolved in liquid tin and lead which both have moderately high vapor pressures as metals and form volatile sulfides. The limit on the size of the metal samples which may be used is set chiefly by the difficulties of analysis for very small amounts of sulfur. The oxygen or carbon dioxide combustion method, followed by iodimetric determination of the sulfur dioxide which is formed,has been found to be successful for the determination of small amounts of sulfur in copper, iron, cobalt and nickel.4 This method was unsatisfactory for sulfur dissolved in tin and lead, mainly because the sulfur dioxide was to some extent absorbed by the copious tin or lead oxide deposits which were formed on the walls of the combustion tube. Furthermore some of the sulfur was found to segregate on the surface of the beads as flaky sulfide crystals which would easily be lost in the transfer of a bead from a boat in the gas equilibration apparatus to one in the combustion apparatus. Oxidation in aqueous media to sulfate ion followed by precipitation as barium sulfate was, therefore, adopted as the analytical procedure. The gas-metal equilibrium experiments were all carried out with radioactive sulfur and thus the analysis involved the counting of barium radiosulfate. Furthermore the use of the radioisotope meant that the approach to the gas-metal equilibrium could be followed continuously by gas counting.&apos; The metal beads were held separately in glass crucibles during equilibration and were transferred from the furnace to the beaker for dissolution in nitric acid still in the crucibles, and thus the possibility of sulfur loss by detachment of the sulfide segregates was eliminated. The temperature range of this investigation was 500° to 680°C. EXPERIMENTAL APPARATUS AND METHOD The apparatus consisted of two furnaces placed in series in a gas recirculation system, Fig. 1. One furnace F1, which was vertical was used to heat the alumina crucible, A, holding six metal beads in separate glass crucibles. The beads weighed between 300 and 700 mg each. The crucible assembly was introduced and removed from the furnace mechanically under a stream of oxygen-free argon. The other furnace, F2, was horizontal and was used to heat a cobalt Co9S8 mixture, held in an alumina boat, and made with radiosulfur containing about 1/2 millicurie per g of sulphur. This mixture, which was finely powdered, was used as a source of known H2S/H2 mixtures6 for a given furnace temperature. The recirculation system also contained a gas re-circulation pump (P), an end window Geiger-Miiller counter (N)—placed downstream of F1 so as to monitor the H2S pressure in the gas leaving this furnace— a sample volume for chemical analysis of the gas phase (G), gas drying tubes (D), filling taps and other standard ancillary equipment. The gas sampling volume was principally used in the cali-

Jan 1, 1962

By B. L. Averbach, M. F. Comerford, M. B. Rough

The volume fraction of ß phase was determined in a Ti-6Al-4V alloy by measurements of integrated diffraction intensities. The (0002), and (100)ß diffraction lines were chosen because this combination minimizes the errors resulting from preferred orientation. The difficulties arising from fluorescence radiation were eliminated by use of a diffracted beam monochromator. A specimen quenched from 1475OF (800°C) contained approximately 5 pct ß, but in specimens quenched from higher temperatures no ß was found. The ß phase formed during aging, and in specimens solution treated at 1570oF (855oC) approximately 10 pct ß was present after aging at 1000°F (540°C) for 24 hr. This ß appears to form by decomposition of martensitic a&apos;. ThE kinetics of the reactions which occur during the heat treatment of titanium alloys are complex &apos; and not completely understood. It has been proposed that hardening occurs in some alloys&apos; on aging by the precipitation of a transition phase w followed by the formation of the stable a and ß phases. It has been proposed for other alloys2 that the a&apos; marten-site decomposes by precipitating finely dispersed a particles. Most investigations have been hampered by the difficulties of determining quantitatively the amounts of the various phases present. This paper is concerned with the measurement of the amount of ß phase by an X-ray method, similar to one developed for the determination of retained austenite. The principal new feature was the use of a mono-chromator in the diffracted beam in order to reduce the fluorescence arising from the sample. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of nominal composition Ti-6Al-4V (actual weight percentages: 6.2 Al, 4.1 V, 0.02 Mn, 0.17 Fe, 0.005 H, 0.03 C, and 0.02 N). The material was received as 5/8-in.-diam centerless ground rods in the annealed condition. The heat treatments were carried out in a vacuum of approximately 0.03µHg. The X-ray intensity measurements were made on 3/8-in. thick discs. The surface was prepared by grinding off about 0.060 in. and electropolishing in a solution af 60 ml (70 to 72 pct) perchloric acid in 1000 ml glacial acetic acid with a current density of 0.5 amp per sq cm.q The X-ray determination is based on the proportionality of the diffracted intensity of each line to the volume fraction of the corresponding phase. In calculating the intensities for a powder sample it is assumed that a large number of grains con- tributes to the diffracted intensity and that the grains are oriented at random. The presence of preferred orientation introduces serious errors in the relative intensities. The material used in this investigation exhibited a strong preferred orientation, which could not be removed by heat treatment. Other investigators have also found that preferred orientation may be retained after phase transformations. Glen and pugh5 performed a detailed analysis of the randomness expected after several allotropic transformations, but stated that this is not observed. Burgers,6 and Burgers and Ploos van Amstel,7 found that, in zirconium, the original orientation is retained after two phase transformations. Newkirk and Geisler8 observed similar behavior in titanium. On the basis of this evidence, it appears that, in the absence of plastic deformation, textures present in annealed titanium alloys are retained. Heating an a-ß alloy to the all-ß region and subsequent cooling to room temperature do not make the orientation of the mar-tensite different from that of the original a phase. In the present investigation it was possible to take advantage of the crystallographic relationships involved in the martensitic transformation to minimize the errors associated with preferred orientation. The relative orientation for titaniu-m marten-site9 takes the form (0001), 11 (110)ß; [1120], 11 [lll]ß. The same relationship has been proposed for zirconium&apos; and certain titanium-base alloys.10-12 Additional sets of approximately parallel planes have been determined for titanium-nickel alloys." The influence of preferred orientation can be minimized by comparing intensities from parallel planes in the two related phases. If it is assumed that each family of planes in a given phase is equally well populated, the effect of preferred orientation can be eliminated by using the normal multiplicity for the family of planes since each set of parallel planes is equally preferred for any orientation of the sample relative to the X-ray beam. The most suitable combination of reflections in the Ti-6A1-4V alloy appeared to be (0002), and (110)ß It must be recognized that the ß formed during aging of the Ti-6A1-4V alloy is a precipitate rather

Jan 1, 1960

By R. F. Dickerson, D. A. Vaughan, A. F. Gerds

ALTHOUGH the metallurgy of uranium has been under intensive study since the early 1940&apos;s, no systematic effort has been made to identify the non-metallic inclusions in uranium. Uranium carbide (UC), which is probably the most common inclusion found in graphite-melted metal, has been tentatively identified by previous investigators, but the other nonmetallic inclusions have received little attention. Since metallography is a valuable tool in metallurgical studies, the metallographic identification of the nonmetallic inclusions in uranium is important. Such an investigation has been completed and the identification of slag-type inclusions and of uranium monocarbide, uranium hydride, uranium dioxide, uranium monoxide, and uranium mononitride is described. Metallographic Preporation It is often possible to prepare specimens for metal-lographic examination equally well by several methods. The specimens which were examined in this work were prepared by one of two acceptable methods. For the convenience of the reader, both methods will be discussed in detail and will be referred to simply as Method I or Method II in the subsequent sections. For both Methods I and 11, specimens for microscopic examination usually were mounted either in bakelite or in Paraplex room temperature mounting plastic. Method I—Specimens were ground in a spray of water on a revolving disk covered successively with 120-, 240-, and 600-grit silicon carbide papers. It was necessary to perform the final grinding operation carefully on worn 600-grit paper to keep the scratches as fine as possible. After washing and drying, the specimens were polished for 3 to 4 min on a slow speed wheel (250 rpm) covered with a medium nap cloth. Diamet Hyprez Blue diamond polishing paste, Grade 00, 0 to 2 µ, was used as abrasive with kerosene as lubricant on the wheel. Specimens were washed thoroughly in alcohol and final polished electrolytically in an electrolyte composed of 1 part stock solution (118 g CrO, dissolved in 100 cm3 H2O) with 4 parts of glacial acetic acid. A stainless steel cathode was used. At an open circuit potential of 40 v dc, a polishing time of 2 sec retained inclusions well with the bath at room temperature. If additional etching was required to sharpen the interface between the metal and the inclusions, an electrolyte composed of 1 part stock solution (100 g CrO3 and 100 cm8 H20) and 18 parts glacial acetic acid was used at room temperature. Best results were obtained by etching for from 10 to 15 sec at 20 v dc in the open circuit. Surfaces obtained by this method are suitable for microscopic examination. However, if desired, they may be etched further with other chemicals. Method 11—Rough grinding was done on a wet 180- or 240-grit continuous grinding belt. The specimen was then ground by hand successively on 240-, 400-, and 600-grit silicon carbide papers in a stream of water. Final polishing was accomplished on a 4 in. high speed wheel (3400 rpm) covered with Forstmann&apos;s cloth. Linde B levigated alumina, suspended in a 1 volume pet chromic acid solution, was the abrasive. Specimens usually were polished in 5 min or less by this technique. Often the inclusions present in the metal were identified in the mechanically polished condition. When etching was required to outline inclusions more sharply, one of the two following methods was used. In the first method, the specimen is etched lightly while electropolishing in the chromic-acetic acid solution described above (1 part of stock solution to 4 parts of acetic acid). The electrolyte was refrigerated in a dry ice-ethyl alcohol bath and specimens were etched at 60 v dc on the open circuit for 2 or 3 cycles of 3 to 4 sec each. The second technique utilizes electrolytical etching at about 10 v dc (open circuit) in a 10 pet citric acid solution at room temperature. X-Ray Diffraction Technique The major problem in the identification of inclusions in metals by X-ray diffraction techniques is the extraction of a sufficient amount of each type of inclusion to obtain an X-ray diffraction pattern. In the present study, X-ray diffraction patterns were obtained from individual inclusions of the order of 10 µ diam. The polished and etched samples shown in the micrographs were examined at a magnification of X54 or XI00 with a binocular microscope. This allowed sufficient working distance to extract the inclusions with a needle probe for powder X-ray diffraction analysis. Friable inclusions such as MgF2, CaF2, UO2, and UH3 could be freed from the metal by probing the as-polished and etched surface. The fine particles then were picked up on the end of a Vistanex-coated glass rod (0.002 in. diam) which was held in a brass adapter made to fit the powder X-ray diffraction camera. The end of the glass rod was centered in the path of the X-ray beam. In the case of the UC, UO, and UN inclusions which are smaller in size, more metallic in appearance, and less friable than the other inclusions, it was necessary to etch the inclusion in relief before extraction. UN inclusions etched sufficiently in relief in the electrolytic polishing solution described in Methods I and II by increasing the polishing time. UN inclusions were relief etched by extending the

Jan 1, 1957