Search Documents

By John C. Bilello

The brittle fracture behavior of cold-worked sintered tungsten was studied over the temperature range 4.2° to 298°K using a high-sensitivity strain measuring system and electronfractography. Similar observations were made on a swaged electron beam zone-refined monocrystal. In sintered tungsten irreversible plastic deformation was observed during cyclic load-unload tests at stress levels well below the fracture stress for all temperatures, but general microyielding could be detected only down to 202°K. For the zone-refined samples macroyielding occurred at all test temperatures with evidence for twinning below -202°K. The fracture stress of the sintered tmgsten was virtually independent of temperature, while the zone-refined crystal showed a 2.3 times increase over the same temperature range. Electronfractography confirmed the presence of numerous rod-shaped and spherical submicroscopic voids which ranged in diameter from 1400 to 4300A in the sintered tungsten; no voids could be found in the zone-refined tungsten. Contrast effects observed on the replicas in the vicinity of certain voids indicated that plastic deformation could be induced by the local stress concentration. It has been suggested that the presence of these voids may be responsible for the low-temperature brittle failure of sintered tungsten. Based m this suggestim und on the evidence obtained here, a dislocatim model is presented to account for the brittle behavior of sintered tungsten. In this model slip, which is induced by the local high stress concentration in the region at the edge of a favorably oriented void, could cause the void to grow to a microcrack of critical size. STUDIES of brittle fracture in bcc metals have led to the well-known experimental relationships between grain size, yield stress, fracture stress, and temperature which have formed the basis for the various dislocation pile-up1-3 or interaction4'= models for slip-induced microcrack nucleation. While microcracks can be nucleated by deformation twins,6,7 there has been no direct evidence furnished by transmission electron microscopy to support conclusively either the Zener pile-up or Cottrell dislocation reaction models for producing micro-cracks in all "brittle" materials. In addition to the "inverse" grain size relationship for yield and fracture stresses the cottrel14 theory predicts that the fracture stress below the transition temperature should behave in a fashion similar to that of the yield stress above this temperature. Such behavior has been verified for several bcc metals.8-10 With reference to both grain size effects and the tem- perature dependence of the fracture stress below the transition temperature, the behavior of sintered tungsten appears anomalous. Early work by Bechtold and Shewrnon 11 showed no apparent temperature dependence of the fracture stress below the ductile-brittle transition temperature (DBTT). They attributed this result to the intergranular nature of the fractures observed. More recent work by Wronski and Four-deux12'13 on considerably purer material did not show any systematic relationship between the fracture stress and temperature below DBTT. The dependence of flow and fracture stresses on grain size is also not clearly established for sintered tungsten. Koo, for example, has shown that the DBTT for sintered tungsten depended chiefly on the annealing temperature and was relatively insensitive to the actual grain size achieved. Using electrofractography and transmission electron microscopy, Wronski and Fourdeuxl3 showed that numerous spherical and rod-shaped submicroscopic voids could be found in sintered tungsten but not in melted tungsten of nominally the same purity. They suggested that these voids could be responsible for the temperature insensitivity of the fracture stress below the DBTT. In the present work the temperature dependence of the fracture stress for high-purity commercially sintered tungsten has been determined. The presence of submicroscopic voids in sintered materials was confirmed, and these were studied in detail to examine the role they could play in nucleating brittle fracture. A dislocation model is suggested which could cause an inherent spherical void to lengthen into a Griffith crack of critical size. EXPERIMENTAL PROCEDURE Commercially sintered tungsten rod was obtained in the as-swaged condition from Sylvania. A zone-refined crystal was obtained from the same source. This crystal was grown by giving three zone passes (at 25.4 cm per hr) to a sintered rod of high-purity tungsten. The rod axis prior to cold working was -15 deg from the [110] direction. Originally the zone-refined rod was -6 mm in diam; it was reduced to -3 mm by eight swaging passes, at high temperatures, with each step having about the same reduction of area. The final swaging step gave a 7.5 pct reduction of area at 1050°C. All swaging operations were performed in a hydrogen atmosphere. For the sintered rod a similar working schedule was employed. Metal-lographic examination of the sintered material revealed that the cold-worked structure had an apparent grain diameter of -25 u transverse to the swaging direction (obtained by the intercept method). In the longitudinal direction cold-worked grains were approximately 1.5 to 2 times their diameter. No distinct fiber structure could be observed optically for the zone-refined rod. The cold-worked structure in the

Jan 1, 1969

By G. K. Burgess

THE question of the allotropy of iron, in spite of a vast amount of experimental work and perhaps an even greater amount of theorizing, is not yet settled. That there is a definite transformation in iron near 900,° the A3 point, is generally recognized, as well as the fact that the temperature of this transformation is lowered by the addition of carbon and metallic elements. On heating, the transformation Ac3 is always found at a higher temperature than the transformation on cooling, Ar3. Whether the A3 transformation is sharp like the melting point of a pure substance, or extends over a considerable range of temperatures, embracing perhaps as a lower limit the A2 change, appears to be still an open question for pure iron. The nature and identity of the A2 transformation, it would appear from recent publications, has not yet been satisfactorily settled. In the present paper a critical, historical summary is given of the experimental investigations of the location of A2 and A.3 in pure iron, together with brief mention of some of the theoretical aspects of the subject, and an account is given of a series ?of experiments carried out with several samples of very pure iron which were studied by two methods of thermal analysis in the range from 5000 C. to 1,000° C., and which it is believed furnish a contribution of considerable interest as to the location and nature of the A3 and A2 transformations. Great attention has been given to the details of experimental manipulation and to the preparation of the samples, as it was soon found that some of the discrepancies noted in the work of many experimenters may be traced largely to lack of precautions which we have found essential. For example, to anticipate somewhat, it is necessary to provide a suitable practically gas-free furnace, the heating and cooling of which may be regulated to a nicety. To render a minimum the deforming effects on the cooling and heating curves of the poor conduction of the sample, it must be of a form and mass to pass on its heat rapidly and completely to the thermocouple; and finally the sample itself must be freed from gases which, if present, further mask the definiteness of the heating and cooling curves. We, have also varied within wide limits the several factors which may influence the determination of the exact location and shape of the transformation ranges, especially the mass and preparation of sample, rate of heating and cooling, design of furnace; and finally, as nearly as it is experimentally possible, we have worked with a substance approaching pure iron, free from occluded gases and other impurities, and contained within a vacuum.

Jan 10, 1913

By H. E. Cline, J. L. Walter

Grain boundary sliding and migration were studied in pure aluminum bicrystal and polycrystal samples with two-dimensional grain structure. Scratches, 50 P apart, were used for measurement of sliding and migration distanceso. Samples were deformed at constant rate at 315C and events recorded continuously on wrotion picture film. Electron micrograPhs of boundary-scratch intersections were obtained. Yield and flow stress values were measured. The sequence of sliding and migration events for a three-grain junction is described in detail. Sliding depended only on the resolved shear stress imparted to the boundary. Sliding was accowmodated by formation of shear zones in grains opposite triple points and adjacent to curved boundaries. These shear zones provided the driving force for grain boundary migration. Migration caused rumpling of the boundaries, decreasing the sliding rate. Sliding and migration generally began at the same time, occurred simultaneously and ended at the same time. In the bicrystal, sliding and migration rates were proportional. Initial sliding rules of 5 X joe cm per sec. were measured for the polycrystal and bicrystal samples. These sliding rates agree wilh the internal friction experirnents of K;. The observations seem consistent with a viscous boundary sliding nzechanism. GRAIN boundary sliding is the translation of one grain relative to its neighbor by a shear motion along their common boundary. Sliding is thought to be an important mode of deformation at elevated temperatures and at low strain rates such as prevail in creep,' and perhaps in the area of superplastic behavior.2"4 Although much work has been done to investigate grain boundary sliding, the effort has not led to the identification of a mehanism. KG showed that grain boundaries in aluminum exhibit a viscous nature under very small displacements of internal friction measrements. Various dislocation mechanisms have been proposed but are without conclusive experimental support. Attempts to relate sliding to 6's viscous boundaries have been unsuccessful in that measured rates of sliding are always several orders of magnitude lower than KG'S results would predict.= In bi crystals7and polycrystalsR of aluminum tested under constant load, the grain boundary sliding was found to be proportional to the total creep elongation which indicated that sliding might be controlled by deformation of the grains. Shear zones were observed to extend beyond grain boundaries at triple points to accommodate the sliding.8 Surface observations brought forth the opinion that sliding and migration occurred alternately, in sequence.' Measurements of sliding at the surface have been criticized because they might not be representative of the interior of the sample. Generally speaking, it seemed that much of the previous work and knowledge was based on observations made at relatively low magnification and examination of samples after deformation had been accomplished. Thus, it was the purpose of the present study to continuously record, at high magnification, the events occurring during the deformation of pure aluminum. Samples with two-dimensional grain structures were used to simplify interpretation of the results. The sliding and migration of small areas of many samples were continuously recorded by time-lapse motion pictures. Replicas of the surface were used to provide high-resolution electron micrographs. These observations, coupled with tmsile strength data, provide sufficient information to arrive at an understanding of the phenomenon. EXPERIMENTAL PROCEDURE An ingot of 99.999 pct A1 was rolled to sheet, 0.127-cm thick. Tensile specimens, with a gage length of 0.85 cm, were machined from the sheet. Bicrystal tensile specimens, of the same dimensions, were spark cut from a large bicrystal ingot. The grain boundary was oriented at 45 deg to the tensile axis. The surfaces of the tensile samples were ground flat on fine metallographic paper and were then electropolished in a solution of 75 parts absolute alcohol and 25 parts of perchloric acid. The solution was cooled in an ice-water bath. Using a weighted sewing needle suspended from a small pivot on a precision milling machine, a grid of fine scratches, 50 p apart, was scribed on one surface of the sample. The polycrystalline samples were then annealed in hydrogen for 15 min at 350" to 400°C to produce a two-dimensional grain structure of about 0.2-cm average grain diameter which would not undergo further growth at the test temperature, 315OC. Examination of both surfaces of the samples showed that the grain boundaries were perpendicular to the surface of the polycrystal and bicrystal samples. A hot-stage tensile machine was constructed for use with an optical microscope as shown in Fig. 1. The specimen is shown mounted in the grips. The grips ride in V-ways so that the sample can be mounted without damage. The rear grip is free to slide so that when the sample expands during heating it is not put under a compressive stress. When the grips and samples are at temperature, the rear grip is locked in place by two set-screws. The other grip is connected to a synchronous drive motor which, through a worm gear and a fine-threaded rod, deforms the

Jan 1, 1969

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1753 from the Kanawha licks. Practically all this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the white man, Indians are known to have made salt from salt springs such as those that existed at Avery Island, LA, Charleston, WV, Saltville, VA, and Onondaga, NY. In 1862 the first rock salt was mined in the US from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, VA and then at Retsof, NY in 1885. Of the more than 39 million tons produced annually in the United States, about 58% or 23 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc. Utilization of cavities created in salt beds and domes has grown rapidly since 1947 until now the waste salt is creating an ecological problem. The uses for both dry- and solution-mined cavities range from the storage of liquid hydrocarbons to containerized storage of toxic wastes, from compressed air for the peak shaving of power to storage of nuclear wastes. Geology Mineralogy Properties: Because of its simple structure, halite, the mineralogical name for salt, was the first structure to be analyzed by X-rays. It has the following properties: Formula: NaCl (Na-39.34%. Cl2-60.66% ) Crystallography: isometric, hexoctahedral, 4/m 32/m Space group: Fm3m A0: 5.627 kX Cell contents: Na4CI4 Habit: usually cubic, rarely octahedral, massive, granular to compact Physical properties: Refractive index: 1.554 Twinning: observed on {111} Cleavage: {001} perfect Fracture: conchoidal, brittle

Jan 1, 1983

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By E. C. W. Perryman

The recovery and recrystallization characteristics of superpurity aluminum have been investigated using electrical resistivity, X-ray line breadth, and hardness measurements for the former and the micrographic method for the latter. The three different properties recover at different rates and have different activation energies. The recrystallization results agree well with Avrami&apos;s theory and furthermore indicate that the perfect subgrains formed during recovery are not the nuclei for re-crystallization. WHEN a metal is plastically deformed, its physical and mechanical properties generally undergo considerable changes and by subsequent annealing these changes are partly or wholly annihilated. Thus, a recovery process can be discussed, taking this term in its general sense. In practice, however, there is reason to discriminate between two apparently different processes, one most easily followed at low temperatures, in which the properties return to an almost constant value between that of the cold worked and fully annealed material, and a second process in which the properties return to their original values before cold working and which is accompanied by the formation and growth of new grains having an orientation different from that of the matrix. In this paper the word recovery will be taken to mean the changes in some property as a function of annealing time which occur either without the appearance of new grains or under conditions such that the new re-crystallized grains are very small (= 2 microns), are very few in number, and substantially do not affect the property being measured. This definition is rather abitrary, for it will depend upon the sensitivity of the technique used for the observation of new recrystallized grains, which in the present work was about 1 to 2 microns. However, it is helpful to use the term recovery in this sense and to reserve the term recrystallization for the processes of nucle-ation and growth of new grains in the cold worked matrix. Although considerable work has been done on recovery and recrystallization, most workers have based their study on the measurement of one or perhaps two parameters. Since very small amounts of impurities have such a profound effect on the recrystallization characteristics of a pure metal, it becomes extremely difficult to correlate one piece of work with another. With this in mind, the present work on recovery and recrystallization was done on the same material. Experimental Procedure Material Used and Fabrication: The composition of the superpurity aluminum used throughout this investigation was 0.002 pct Cu, 0.003 pct Fe, 0.003 pct Si, and <0.001 pct Mg. The ingot was hot rolled to 0.250 in., annealed, and cold rolled to 0.034 in. A large number of reductions and intermediate anneals were carried out so as to produce material with a minimum of preferred orientation and maximum homogeneity. For the recovery part of the investigation, the final cold reduction was 20 and 80 pct and for the recrystallization part, 20 pct. After each pass in the cold rolling process, the material was quenched in cold water in order to keep the rolling temperature as near room temperature as possible. Annealing Procedure: For the recrystallization work, specimens 1x1 in. were cut from the 0.034 in. cold rolled sheet and a hole was drilled in each through which a wire was threaded to support it in the salt bath. The temperature of the salt bath was controlled to +2°C and the time taken for a specimen to reach temperature was approximately 5 sec. These 1 in. squares were then divided into three groups, one of which was given 5 min at 318°C and another 2 hr at 244°C. These treatments were such that recovery was almost complete and a well defined subgrain structure produced. Separate specimens of each group were annealed for different times at 301°, 318°, 355°, and 373°C, i.e., three specimens for each annealing time. The delay between finish of cold working and start of annealing was about 1 hr. For the recovery work, strips 0.062 in. thick were cut from the cold worked sheet, annealed, and then given the last cold rolling operation. This was done for each annealing temperature. By this means it was possible to minimize the delay between cold working and annealing. In general, all measurements were carried out within 1 hr of the last cold rolling operation. Annealing at low temperatures was done in an oil bath the temperature of which was maintained constant to +1°C. Electrical Resistivity Measurements: Strips 20x0.5x0.05 in. were machined and the electrical resistance measured using a Kelvin double bridge. Measurements were made in an oil bath maintained at 20rt0.1°C. The same specimen was used for the complete isothermal annealing curve.

Jan 1, 1956

By L. R. Woodyatt, H. J. Beattie, C. T. Sims

Theories correlating the formation of u and related intermetallic compounds to the electron-per-atom density of binary and ternary alloys have appeared regularly in recent technical literature. These same principles can be modified and applied to complex precipitation-strengthened alloys such as the iron-, cobalt-, and nickel-base superalloys and the stainless steels. Since these complex alloys contain carbides and other phases that normally precipitate before the U-type phases, the nature and amount of the precipitated phases must be calculated first. The following general formula is then applied to the residual matrix composition of the alloy: element. The magnitude of the resulting number is indicative of whether the alloy will form a a -type phase. When these calculations (which are computerized) are systematically applied to alloys of knoun phase analysis, a breakoff in average electron-vacancy number is noted between U-free and U-prone alloys. Alloys with an average electron-vacancy number higher than the breakoff form a-type phases, while those with lower ones do not form these phases. This method could then be used to eliminate from consideration all experimental compositions that would precipitate undesirable phases. It also is useful in evaluating analyzed heats of alloys where minor heat-to-heat variations determine whether the alloy is o-free or o-prone. THE highly significant development of strong, ductile superalloys to provide reliable construction materials in the 1000" to 2500° F temperature range has been due principally to unremitting application of Edisonian techniques and logic by the dedicated physical metallurgists who have shouldered this responsibility. Tools such as the electron microscope, phase analysis, and computers to accomplish regression analyses have been used heavily, but the effort has been essentially practice of an art, rather than a science. The objective of this paper is to describe and illustrate application of some relatively fundamental principles to certain of these alloy systems in an attempt to remove some of the empiricism from the technology. Specifically, the work presented here deals with the use of periodic-group relationships to predict the formation of intermetallic phases which can occur in primarily austenitic (fcc) structures. Calculations that have been developed might be applied in the design of new alloys and the evaluation of known alloys, and thus have the potential of eliminating vast areas of unnecessary alloy preparation and evaluation. ALLOYING CONCEPTS AND STRUCTURAL FEATURES OF SUPERALLOYS Strength is produced in austenitic superalloys by three principle mechanisms: 1) precipitation of y&apos;; 2) formation of carbides; 3) solid-solution hardening by soluble refractory metals. The first mechanism requires the addition of aluminum and titanium, the second requires carbon and carbide-forming elements, while the third calls for the addition of molybdenum and/or tungsten. A considerable concentration of chromium is usually maintained to resist oxidation/corrosion, but it is also an important carbide-forming element. Fig. 1 shows a sketch and electron micrograph of the structure of a typical wrought nickel-base super-

Jan 1, 1967

By W. Bonfield

A study has been made of the dislocation substructures produced in hot-pressed beryllium specimens strained to various levels in the range from 800 x 10-6 In. pev in. to fracture. A number of distinctive dislocation configurations were observed in this region which had not been noted at lower levels of strain. These included dislocation-dislocation interactions to form networks, dislocation "walls", subgrain boundaries and complex arrays, interactions between dislocations and large beryllium oxide particles, and the generation of dislocations from certain particles. The nature of these differences in substructure and their relation to the stress-strain characteristics of polycrystalline beryllium are discussed. In a previous study1 of the plasticity of commercial-purity, hot-pressed beryllium a transition was found in the deformation characteristics in the mi-crostrain region. The initial plastic deformation could be represented by a parabolic stress-strain equation, but above a critical stress there was a complete departure from this relation and a reduction in the strain-hardening rate. The dislocation configurations produced by various levels of micro-strain in this region were examined by transmission electron microscopy and a general correlation was established between the observed transition in deformation characteristics and the dislocation structure of the material. The two stages in the micro-strain region distinguished in these experiments were designated as Stage A&apos; and Stage B&apos;. Stage A&apos; type deformation generally was noted up to a plastic strain of -80 x 10"6 in. per in. and Stage B&apos; type from -80 x 10-6 to -800 x 10&apos;6 in. per in. The discovery of two stages in the microstrain region naturally posed pertinent questions as to the existence of any further distinct stages in the subsequent plastic deformation. The purpose of this paper is to present a study of the dislocation configurations produced in similar beryllium specimens strained to various levels in the range from -800 x 10 in. per in. to fracture and to discuss the relation between substructure and the stress-strain characteristics. It is concluded that this region of strain can be considered as a distinct stage in the plastic deformation of polycrystalline beryllium. Tensile specimens of gage length 1 in. and cross section 0.18 by 0.06 in. were prepared from commercial-purity, hot-pressed QMV beryllium and then annealed at 1100°C for 2 hr. 2 followed by a careful chemical polishing procedure.3 The specimens were strained at a constant rate to various levels of strain in the range from -800 x 10-6 in. per in. to fracture (at 0.5 to 2 pct elongation), using the Tuckerman strain-gage technique1 to measure plastic and total strain. Thin foils were obtained from the strained and fractured specimens by chemical polishing3 and were examined using an RCA-EMU 3 electron microscope. Considerable care waS taken to avoid both accidental deformation during the preparation of the thin foils and excessive heating during their examination. Selected-area diffraction patterns were determined for each micrograph. Tilting experiments were also performed whenever appropriate to establish the dislocation zero-contrast position and hence determine the Burgers vector. This operation was sometimes not possible due to the rapid contamination of the foils which occurred in the electron microscope. RESULTS AND DISCUSSION To enable the distinctions between the dislocation arrays at high and low strain levels to be adequately made, the main characteristics of Stage A&apos; and Stage B&apos; deformation are briefly reviewed. 1) Stage A&apos;. In the annealed starting condition there was a variable density (5 x 107 to 3 x 10&apos; cm per cu cm) of isolated dislocations within a grain. The initial deformation in a tensile specimen was heterogeneous, with the dislocation density increasing in a few grains to 5 x 10g to 1.5 x 101° cm per cu cm. The deformation occurred exclusively on the basal plane by the movement of one or more 1/3 (1130) type dislocation systems. The dislocations were long and regular in form and nearly all the intersections exhibited a simple four-point node configuration. No interactions between glide dislocations and beryllium oxide particles were observed. 2) Stage B. In Stage B&apos; there was a large increase in the number of grains exhibiting dislocation movement and also a change in the nature of the deformation, in which jogged dislocations and elongated loops became the characteristic feature. The splitting up of the elongated loops into smaller loops and the possibility of source action from the re-

Jan 1, 1965

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

By H. B. Huntington

Some of the basic problems in understanding elec-tromigration in metals are discussed, along with the attempts that are being made to handle them. One such problem is the effect of the electrostatic forces. It is now acknowledged that the momentum exchange with charge carriers plays generally a dominant role in the driving force but the question remains to what extent the electrostatic force may still be effective. The electromigration of interstitial impurities is also an area which presents some intriguing questions. For the substitutional impurity, moving by the vacancy mechanism under the influence of an electric field, the correlation considerations are somewhat more complex than have been previously recognized. Another problem of basic importance in the calculution from first principles is the strength of the "electron friction" force, say for a simple one-band metal. A related problem growing out of the preceding is the prediction of the direction of the "electron wind" force for metals with band structure involving both holes and electrons. THE term electromigration has come to be used to describe the flow of matter in condensed phases carrying high electronic currents such as metals and alloys, whereas one usually reserves the term electrolysis for situations where the current is largely ionic, particularly in the liquid state such as molten salts. It follows that the mass transport number in electromigration is always very small, of the order of 10-7. Studies of electromigration date back some 30 years but the modern period would appear to date from the work of Seith and Wever1 who in the mid 1950&apos;s first incorporated markers to display mass motion relative to the lattice and first suggested that the direction of the mass flow was primarily determined by the sign of the charge carriers. Since that time interest in the field has grown steadily and more rapidly recently as certain technological applications became apparent. Chief of these is certainly the deleterious effects that electromigration can cause, even at relatively low temperature, to current-carrying elements in integrated circuitry.2 These phenomena have been the subject of intense study and considerable ingenuity. On the constructive side electromigration has proved a useful tool in the purification of certain metals.3 The interest of this paper is, however, centered more on the basic aspects of the subject than on its technological applications. That high electric currents should give rise to mass flow in metals and that the driving force should be more directly associated with momentum exchange with the charge carriers than with the electrostatic field are ideas that no longer cause surprise or particular interest. The field has matured to the point where the general concepts are widely accepted and continued progress in basic understanding rests on more detailed and quantitative exploration. It is the purpose of this paper to point out what are some of the current problems. As a result, we expect to raise more questions than we answer. The first of these will be the role of electrostatic forces, if any, in electromigration. A second section will deal with the electromigration of interstitials. A third and final section treats with electromigration of substitutional impurities or of the matrix atoms themselves. ELECTROSTATIC DRIVING FORCE In the conceptual treatments of electromigration it has been customary to write the driving force in terms of an effective charge number Z* and to divide it into two terms F = e£Z* = e£[Zel- z(pd/Nd)(N/p)(m*\m*\)] [1] The first of these represents the electrostatic force under immediate consideration in this section and the second and usually dominating term for metals arises from momentum exchange with charge carriers, commonly called the "electron drag" term. As can be seen it is set proportional to the electrons per atom, z, and the ratio of the specific resistivity of the moving entity to the corresponding resistivity per matrix atom. The (m*/Im*I) factor takes into account the fact that the sign of the charge carrier determines the sign of the driving force. The specific resistivity of the moving entity is averaged over its path. In the case of motion of the matrix atoms by vacancies this gives rise to approximately one-half the resistivity at the saddle point since the scattering power of the atom at its equilibrium position bordering the vacancy differs only slightly from that of a normal matrix atom. Although the formulation of the "electron drag" term in Eq. [I] is based on a highly simplified model for electron defect scattering, the essential features implicit in the expression are common to all the theoretical approaches that have so far appeared in the literature.4-6 As for Zel, most treatments of electromigration have included the quantity as the parameter which measures the direct interaction of the electrostatic field with the ion and equated it to the nominal valence of the latter. However, there has been considerable discussion whether this interaction may not be 0 in many cases.6 If the moving ion is always enveloped by the same distribution of shielding charge, then clearly its motion will not involve any work done by the electric field and one can expect there will be no electrostatic force exerted on such a neutral composite. From this point of view the shielding charge around the ion would be said to be complete and hence the entity within the Debye shielding sphere would be unaffected by the electrostatic field per se. There is, however, the prospect that, as the moving ion progresses, new charge comes in to participate in the shielding action

Jan 1, 1970

By T. H. Oxnam

The predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold also is carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the un-roasted sands and slimes. The sands are treated by leaching, and the so-called " accumulated slimes " by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. Palmarejo Mines. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12 miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which

Jan 1, 1906

By S. Shapiro, J. A. Ford

The crystallo graphy of several grains of the lamellar Ni-Ni3 B eutectic solidified under conditions appvoachirt equilibriun has been examined.. A preferred interlace relationship has been observed in this system which may be described as: A detailed study of this interface by means of an atomistic model reveals the interface Plane to be puckered and more accurately describable as: Analysis of the atomic configuration on these planes reveals that this interface conforms to the orientation criteria proposed for directionally solidified lanzellar eutectics. In addition, a model is proposed to help explain the growth of a "puckered" interface. DURING the past several years an increasing number of unidirectional solidification experiments on eutectic alloys have been reported in the literature. The primary emphasis, in most cases, has been the effect of growth variables on microstructure. Some authors have, however, studied the crystallographic orientations and interfacial relationships resulting from these experiments. Four crystallographic studies have been published;&apos;-4 in each of these there is a factor which tends to prohibit the extension of the observations beyond the particular system. In the Al-CuA12 system, the approximately equal volume fractions of the phases have resulted in sorrie controversy as to which phase constitutes the matrix. In the Mg-Mg,Sn eutectic the presence of several interconnecting lamellar systems2 complicates the analysis. The two remaining eutectics. 1nSb-b and Al-Ali, are both rodlike (the latter exhibits a plate morphology at low solidification rates): the matrix in each of these alloys is the simpler (fcc) phase. Studies of nucleation in eutectic alloys indicate that the more complex constituent is the nucleating -.phase.&apos; For the purpose of an analysis of interface crystallography it was deemed desirable to study a lamellar system in which the matrix was the more complex and, presumably. the nucleating phase. Recently it has been shown that there is a eutectic in the Ni-B system between Ni3B and i; preliminary investigation by the authors indicated that the matrix in this eutectic is the boride phase. The structure of Ni,B is reported to be orthorhombic, the compound being isostructural with cementite. This eutectic is therefore analogous to that between austenite and cementite. Furthermore, the Ni-B system is not susceptible to a competing eutectic reaction as occurs in the Fe-C alloys; nor does it exhibit a eutectoid decomposition. For these reasons the study of the interfacial relationship in the Ni-Ni3B eutectic was undertaken. PROCEDURE Ingots of nominal composition 3.5 and 3.6 wt pct B were induction-melted in boron nitride crucibles within a graphite susceptor under a boric oxide slag; a dynamic argon atmosphere was maintained over the melt to prevent rapid oxidation of the susceptor. The raw materials used were 99.97 pct Ni from Huntington Metals Division of International Nickel Co. and 99.8+ pct B chips supplied by the United Mineral and Chemical Co. The analyses of the starting materials are listed in Table I. The melt was held at 1500cC for 2 hr to insure complete reaction and allowed to cool to room temperature. The castings were chemically analyzed for boron and were metallographically examined for uniformity. The metallographic samples were mechanically polished through 0.1 p A1,0, and etched with Carapella&apos;s reagent. Each master casting was cut up to make several specimen blanks which were remelted, in boron nitride crucibles, to form ingots of 1/2 to 3/4 in. in diarn by 7 in. long. These ingots were unidirectionally solidified using a modified vertical Bridgman technique. The rate of solidification was assumed to be equal to the uniform rate at which the crucible-susceptor assembly was withdrawn from the induction coil. This rate was varied from 1.18 to 2.21 cm per hr. In order to perform these experiments it was found necessary to redetermine the eutectic composition. This was accomplished by the zone-melting technique described by Yue and lark.&apos; An ingot of 4.5 wt pct B was zone-melted in a horizontal boron nitride boat 7-1/2 in. long with a 112-in.-square cross section. A

Jan 1, 1967

By J. E. JR. Johnson

AT the Cleveland meeting of the Institute in October, 1912, I had the honor to present a paper outlining the conditions surrounding the charcoal iron industry, and giving some of the results of an investigation started about three years ago for the purpose of determining the reason for the poor reputation of the Lake Superior charcoal irons as compared with the Southern and Eastern irons. In that paper I explained the effect of high carbon on quality, and tried to make clear that that paper was a preliminary one, as we felt convinced that we should eventually discover other factors affecting quality. The progress of the investigation has brought out facts that seem to us of the utmost importance practically and theoretically, and the purpose of the present paper is to present these facts with the proofs which seem to us to establish them. The closing year of the nineteenth century saw the publication of the first definite and connected statement of the relationship between the cast irons and the steels.&apos; The metallurgical world was ready to accept the fundamental unity of these two series, acceptance being greatly hastened by Professor Howe&apos;s classic paper, The Constitution of Cast Iron, presented at the Richmond meeting of the Institute, February, 1901.

Jan 1, 1914

By R. F. Krueger

Results are presented from tests of dynamic fluid-loss rates to cores from clay-gel water-base drilling fluids containing different commercial fluid-loss control agents (CMC, polyacrylate or smt,ch), organic viscosity reducers (quebracho and complex metal lignosulfonate) and oil at several different levels of concentration. In the dynamic system the most effective individual additives to the clay-gel drilling fluid, based on cost-equalized concentrutiom, were found to be starch and the viscosity reducers. These results do not conform with the rankings determined by API fluid-loss rests, which indicate CMC, polyacrylate and starch to be the most effective and comparable. Generally, minimum dynamic fluid-losr rates were attained at cost-equalized concentrations of additive (including thinner) of about $1.00/ bbl, or less. For chernically treated clay-gel drilling fluids, both the standard and the high-pressure API filter-loss tests were found to he inaccurate indicators of trends in dynamic fluid-loss rates under the test conditions used, particulurly for drilling muds containing viscosity reducers. From a practical field viewpoint, restrictions on the applicability of the API fluid-loss test are such that it is open to question whether or not results of this test can be used routinely with confidence as an indicator of control of down-hole fluid loss under field treating conditions. INTRODUCTION The petroleum industry spends large sums of money during drilling operations to control the fluid-loss properties of drilling fluids based on the standard API filter-loss test,&apos; which is a static filtration system. Laboratory studies&apos; &apos; of dynamic filtration have shown that in a given time period filtrate loss from a circulating mud stream is greater than from a static system and that it is a function of linear mud velocity, pressure and the properties of the drilling fluid. Ferguson and Klotz&apos; and Horner, et al," observed that (I) the dynamic fluid-loss rates for the drilling fluids used were not related to the extrapolated API filter loss and (2) the drilling fluids with the lowest API filter losses did not have the lowest dynamic fluid-loss rates. However, there has been no published information on the relative effects on dynamic fluid-loss rate as a given drilling fluid is treated with increasing amounts of chemical additive to reduce the API filter loss. Such information is economically important because drilling-fluid costs rise rapidly as chemical requirements increase. This paper presents the results of a study of dynamic filtratioi rates to cores from a clay-gel water-base drilling fluid treated with various commercial viscosity reducers and chemical fluid-loss control agents. The dynamic fluid-. loss rates to cores are compared with the standard API filter-loss values at several different levels of additive concentration. Dynamic filtration rates were obtained in each experiment under two different simulated wellbore conditions: (1) filtration just above the bit through a new mud cake laid down dynamically on a freshly drilled formation and (2) filtration up-hole through a mud cake formed by deposition of a static filter cake on top of the initial dynamically formed cake. The latter case corresponds to the bottom-hole conditions existing above the bit when mud circulation is restarted after a stand of pipe has been added or a round trip has been made to change the bit. Except for the short-duration, high-rate filtration beneath the bit where no mud cake can form, these two conditions probably represent the two extremes of dynamic filtration. Because thickness of a dynamic mud cake formed on freshly exposed formation is limited by the shearing action of the mud stream, the filtration rate for this condition is high. On the other hand, once circulation is stopped and a static mud cake forms on top of the dynamic cake, re-starting circulation has only a small effect on the cake properties and filtration rate is much lower thereafter. A discussion of the mechanics of mud-cake deposition and dynamic filtration is outside the scope of this paper but may be found in more detail in publications by prior investigators. APPARATUS AND EXPERIMENTAL CONDITIONS The test equipment used to simulate the dynamic flow conditions existing during drilling was a modification of that described previously by Krueger and Vogel: A schematic flow diagram is shown in Fig. 1. In general, a power-driven, high-pressure mud pump capable of delivering up to 60 gallmin was used to circulate drilling fluid parallel to the faces of 1-in. diameter sandstone cores mounted in a 2 3/4-in. ID high-pressure test cell. Pump rates were controlled by means of a magnetic clutch to maintain an average axial fluid velocity of 110 ft/min in the annular space between the cell wall and a 1 1/2-in. rod positioned on the center line of the cell. The core specimens were Berea sandstone plugs sealed with plastic inside 1 1/8-in. OD tubes and were fluid-saturated prior to use. Burettes were used to accumulate fluid discharged from the cores. The mud sump shown was used for treatment and storage of the drilling-fluid samples during a particular test. The valve arrangement permitted either (1) circulating drilling fluid through the by-pass line while treating with

By B. F. Zwick

No new fields have been discovered in Ecuador during 1945, though Shell. Company of Ecuador&apos;s Vuano No. 1, near Arajuno in the Oriente concession, which was reported to have drilled to .5281 ft., tested a small, noncommercial quantity of 13° gravity oil. In the upper section, the well tested large flows of fresh water and has been abandoned. Shell is preparing to move to another location.

Jan 1, 1946

By C. T. Liu, J. Gurland

The deformation behavior in tension of spheroidized carbon steels was studied at room temperature as a function of carbon content, 0.065 to 1.46 wt Pct, and carbide particle size, 0.88 to 2.77 p. It was found that the Hall-Petch strength-grain size relation is directly applicable to the yield and flow stresses of the two lower-carbon steels , 0.065 and 0.30 pct C. The strength data for the medium- and high-carbon steels, 0.55 to 1.46 pct C, also satisfied the Hall-Petch relation, provided that these data are based upon the particle spacing. Beyond 4 pct strain, the flow stress data of all the steels studied could be represented by the same Hall-Petch relation with dinerent spacings for grain boundary and particle strengthening. The behavior of the higher-carbon steels was consistent with the postulated formation of a dislocation cell network during processing and initial deformation (up to 4 pct strain). The cell size was assumed to be equal to the planar particle spacing. The true stress at the ultimate tensile strength was also found to be a function of the particle spacing. At a given temperature and strain rate, the yield and flow stresses of carbon steels depend on the type and dimensions of the microstructure. Starting with the work of Gensamer et al. in 1942,&apos; experimental studies on pearlitic and spheroidized carbon steels revealed that the strength of steels is a function of two main parameters: the ferrite grain size2&apos;3 and the carbide particle spacing;1&apos;4&apos;5 on this basis, two different strengthening mechanisms have been developed to apply to steels of low and high carbon contents, respectively. In polycrystalline iron and mild steels the grain boundaries are regarded as the major structural barriers to slip. The relation between strength and grain size is generally represented by the Hall-Petch equation which is based on a linear proportionality between strength and the inverse square root of the average grain size.2&apos;3y677 However, Gensamer et al.&apos; and Roberts et related the yield strength of medium -and high-carbon steels to the carbide particle spacing alone, and they found a linear relation between the logarithm of the mean free path in the ferrite and the yield strength in both spheroidized and pearlitic steels. By means of the electron microscope, Turkalo and LOW&apos; extended the study to finer structures; they concluded that the logarithmic relation is not valid for the entire range of microstructures unless grain boundaries are also included in the measurement of the mean free path. For the specific case of spheroidized steels, Ansell and aenel&apos; found that the yield strength data,4&apos;5 when plotted as a function of mean free path, fit the Hall-Petch equation; however, T&apos;ysong found that the same data fit the 0rowanl0 relation if a planar inter-particle spacing is used. Recently Kossowsky and ~rown" studied the strength of prestrained spheroidized steels, 0.48 and 0.95 pct C, and concluded that the strength due to the carbide dispersions varies linearly with the reciprocal of the square root of the mean free path between carbide particles and dislocation networks. Such networks were first observed by Turkalo." The conclusion common to all these studies is that the available slip distance in the ferrite is the most important variable in determining strendh. Previous work on carbon steels is restricted to limited composition and strain ranges. The mechanism which governs the flow properties is not clearly understood, and, in particular, little is known about the composition dependence of the transition between grain boundary strengthening and particle hardening. The purpose of the present work is to investigate the strengthening mechanism in spheroidized steels over a wide range of carbon content, 0.065 to 1.46 wt pct, and plastic strain, yielding to necking. The spheroidized structure was chosen because of its relative simplicity and the relative ease of control and measurement of the structural parameters. The experimental work is limited to tensile testing at room temperature at constant extension rate. The effects of the carbide particles on the fracture behavior of spheroidized steels are discussed elsewhere.13 EXPERIMENTAL PROCEDURE Eight different grades of vacuum-cast carbon steels were supplied in the form of forged and rolled plate by the Applied Research Laboratory of the U.S. Steel Corp. The compositions furnished with these steels are given in Table I; the carbon content ranges from 0.065 to 1.46 wt pct, or from 1.0 to 22.3 vol pct of carbide. The steel plates were cut transversely into rods a little larger than the test specimens, 1 in. gage length, i in. diam. The rods were austenitized in air (enriched with CO by a consumable carbon-rich muffle) at 50° C above theA, orA., temperature for 2 hr and then quenched in oil with vigorous stirring. The as-quenched rods were tempered in two stages in order to obtain the desired distributions and sizes of carbide particles. The rods were first tempered at 460° C for 10 hr and then at 700" C for periods ranging from 4 hr to 3 days, in vacuum. After final machining, all specimens were vacuum-annealed again at 650°C for 1 hr in order to relieve residual stresses. The tension tests were carried out in two steps. The initial part of the load-strain curve, up to about 2 pct strain, was determined on a Riehle testing machine with an extensometer of small strain range, 4 pct strain, in order to obtain the yield and initial flow piopertiesi As soon as the first part of the test was finished, the specimen was placed in an Instron testing machine equipped with a strain gage extensometer with a maximum strain range of 50 pct. The load-strain curve to fracture was

Jan 1, 1969

By B. C. Allen

Grain boundary grooving has been studied in chromium, molybdenum, and tungsten under a variety of conditions using high vacuum techniques and tantalum -gettered argon. The average surface free energy of solid chromium, and the chromium-liquid silver interface free energy were respectively found to be 2200 ± 250 and 500 i 130 ergs per sq cm from groove formation kinetics and estimates of pertinent volume difffusion coefficients. The results for chromium were unffected by variations in interstitial content ranging from 0.003 to 0.09 pct C, or 0.003 to 0.03 pct O. Surface diffusion is the primary mechanism of groove formation in chromium under 1 atm argon at 1200" to 140O°C, and is essentially unaffected by 0.003 to 0.09 pct C, 0.003 to 0.03 pct O , metastable nitrogen contents up to -0.01 pct, and up to 2 torr Ag vapor. At higher temperatures, the major mechanism is volume diffusion in argon or evaporation-condensation in stutic vacuum. Surface diffusion occurs in molybdenum at 0.5 to 0.96 and in tungsten at 0.5 to 0.9 of the absolute melting tempera -ture by a single mechanism, possibly by the migration of single adatoms or vacancies. Results were slightly affected by up to 23 tory Sn vapor, and in molybdenum were essentially unaffected by 0.5 Ti or carbon in the range 0.002 to 0.02 pct. Volume difffusion through the liquid is the mechanism of groove formation in chromium-liquid silver at 1200" to 1400°C and in molybdenum-, Mo-0.5Ti-, and tungsten-liquid tin at 1200" to 2000°C. The solid-liquid interface free energies involved were estimated from grooving kanetics. WHEN a grain boundary intersects a solid surface, a groove tends to form along the line of intersection at temperatures above about half the absolute melting point (0.5 TM). The groove progressively grows by preferential atomic migration either by diffusion or evaporation. Establishment of a groove angle occurs in accordance with the grain boundary and surface free energies involved. The motivation for groove formation is a reduction in the total surface free energy of the system. This study is a continuation of previous work on thermal grooving of chromium, molybdenum, and tungsten.&apos; The temperature ranges were extended, and the effect of metallic and interstitial impurities was evaluated. The results were such that certain interface free energies and surface self-diffusion coefficients were deduced from the grooving kinetics. EXPERIMENTAL WORK Materials and Preparation. As indicated in Table I, the 0.05-0.08-cm-thick chromium, molybdenum, and tungsten sheet used was nominally 99.99 pct after recrystallization. Two lots of molybdenum with about the same analysis, Mo-0.5Ti,* and tungsten were ob- *Alloy compsitions are expressed in weight percent . tained commercially. Extruded chromium rod,&apos; prepared from iodide process crystals, was warm rolled to sheet at 700°C. Sheet of three Cr-0 impurity alloys containing up to 0.03 pct 0 was prepared by warm rolling arc melted, extruded, and swaged rod. Two Cr-C impurity alloys containing up to 0.09 pct C were made by equilibrating unalloyed chromium with a known amount of CH4 for 24 hr at 1150°C in previously evacuated quartz capsules. Chromium containing nominally 0.015 and 0.06 pct N was similarly prepared by equilibration with NH3. The sheet was recrystallized to give a stable grain size about equal to the sheet thickness. Molybdenum and Mo-O.5Ti were recrystallized in a tantalum resistance furnace 1 hr at 1 x lo-5 torr at 2300" and 220O°C, respectively. Tungsten was similarly annealed for 1 hr at 2500°C. Chromium and its impurity alloys were outgassed at 1100°C and recrystallized 1 hr at 1700°C under 1 atm Ar. Except for nitrogen, the impurity content stayed roughly constant. Nitrogen in both alloys was reduced to <0.001 pct. In fact, over 80 pct of the added nitrogen was lost after outgassing at llOO°C and annealing sheet 1 hr at 1300°C in argon in the presence of tantalum. Such a rapid loss can be rationalized since -2 torr N are required for equilibrium with 0.04 pct N in solution,3 while the equilibrium pressure is ~10-5 torr over tantalum at 1300°C.4 The recrystallized sheet was cut into small coupons which were metallographically ground and polished on one side with a minimum of grain boundary relief. The surface roughness was on the order of 0.01 µ. The tin and silver used were nominally 99.999 spec-trographically pure. After being outgassed at 1100°C and equilibrated in a molybdenum crucible for 0.5 hr at 1800°C in argon, the tin contained 3 ppm 0, <0.3 ppm N, and 0.1 ppm H. Following outgassing at 900°C and equilibration in a chromium crucible 1 hr at 1400°C in argon, the gas content of the silver was 1 ppm O, <0.5 ppm N, and 0.3 ppm H. Grooving Under Argon or Vacuum. All specimens were placed in unsealed containers made from rod or sheet of the same alloy, thereby enabling the polished surface to achieve gas-solid equilibrium. The annealing fixtures are shown in Fig. 1. The specimen was placed in a resistance furnace with a tantalum or Ta-10W heating element plus tantalum fixtures or radiation shields. Chromium was outgassed at 1100°C, and molybdenum and tungsten were outgassed at 1900°C to 1 x l0-5 torr or at the grooving temperature, whichever was lower. In vacuum anneals, the specimen was then heated directly to the intended grooving temperature. In argon anneals, 99.996 Ar was admitted

Jan 1, 1970

By E. J. Nielsen, P. R. Strutt

A study has been made of the progressive changes in the distribution of etch-pit structures occurring during high-temperature creep in copper + 7 wt pct Al single crystals oriented with a [113] tensile axis. The two equally stressed glide systems with the highest Schmid factor would be expected to form subboundaries of the type predicted by Kear.2 The alignments of etch-pits on sections parallel to different (111} planes consistent with these types of boundaries were not observed. However, they were consistent with planar subboundaries (on a macroscopic scale). From an analysis of Amelinckx1 it may be shown that stable cross-grid dislocation boundaries may form in the primary slip planes. These boundaries form when dislocations with a Burgers vector not in the slip plane move into the plane by combination of climb and glide. THE geometry of subboundaries formed by the interaction of dislocations of two glide systems has been analyzed by Amelinckx,1 and the particular types produced by deforming fee crystals are predicted by ear.&apos; In this paper types of boundaries which may be formed when climb as well as glide occur are discussed as this is relevant in high-temperature creep. It is assumed in the present investigation that the etch-pits observed in Cu + 7 wt pct A1 on surfaces parallel to {111} planes delineate the sites of dislocations. Although there is no direct evidence for this previous work on a-Cu/Al single crystals by Mitchell, Chevrier, Hockey, and Mon-aghan,3 would show this assumption to be reasonable. The alignments of etch-pits which form during creep are studied on sections parallel to each {111) plane. It is then deduced that these alignments are consistent with a specific type of planar subboundary. The Cu + 7 wt pct A1 single crystals had a [113] tensile axis and Fig. 1(a) shows schematically the relation of the slip planes and slip directions (as represented by tetrahedron ABCD) with reference to the tensile axis. The two equally stressed glide systems with the maximum Schmid factor namely ß-AD and (a-BD, from the analysis of Kear,2 would be expected to form the boundaries shown in Fig. l(a) and (b), also Fig. 5(a) and (b). EXPERIMENTAL PROCEDURE The a-Cu/Al single crystals were grown and annealed in a "gettered" argon atmosphere. Chemical analysis showed the aluminum content to be uniform in each crystal and the difference between crystals was maintained to an accuracy of ± 0.25 wt pct. The initial dislocation density and mean subgrain diameter after annealing was -106 cm-2 and 250 µ, respectively. Surfaces parallel to (111) planes were produced by specially developed electrolytic machining processes. The {111} faces were next electropolished for 5 min in a solution consisting of 25 g chromium trioxide, 113 ml glacial acetic acid and 40 ml water; the applied potential was 8 v. Dislocation etch-pits were revealed using l an etchant described by 1 ml bromine, 45 ml HCl, and - 250 ml water. RESULTS In crystals strained into secondary creep at higher stresses (443 and 750 g - mm-2 at 650° C aligned rows of etch-pits parallel to slip plane traces were evident in sections parallel to the (1111, (ill), and (111) planes, see Fig. 3. As well as the longitudinal alignments in Fig. 3, well formed randomly oriented arrays indicative of an equiaxed subgrain structure are evident. At the lower stresses (100 to 230 g . mm-2) only an equiaxed structure formed during creep. The sections in Fig. 3 are from a crystal crept for 70 hr at 650°C with a CRSS of 443 g.mm-2. Two identically oriented crystals were also deformed at the same temperature and stress for 5 min and 4 hr. In the crystal crept for 5 min, the etch-pits were randomly distributed with no tendency for directional alignment, see Fig. 2(a). As shown in Fig. 2(b) aligned arrays were evident after 4 hr creep but they were not nearly so well defined as in Fig. 3. The alignments (parallel to the arrows) in Fig. 3 are consistent with the existence of boundaries in the two main slip planes a and ß. The way in which this is deduced is seen by reference to Fig. l(c), where the existence of boundaries in the a and ß planes is verified by sectioning parallel to a,ß, and d. The (111) and ß(111) planes intersect the d(111) plane along BC [101 ] and AT [011] and alignments parallel to [101] and [011] are clearly evident in Fig. 3(c) in a section parallel to the d(111) plane. Similarly the a, and ß planes in Fig. l(a) intersect each other along DC [110] and hence there will be an alignment parallel to [110 ] in sections parallel to the a-plane and the ß-plane; this is evident in Fig. 3(a) and Fig. 3(b). It is interesting to note that alignments of etch-pits consistent with the boundaries predicted by Kear2 were not observed; see Figs. l(a) and l(b). The geometry of boundaries in {111} planes as shown in Fig. l(c) is discussed later. In Fig. 4(a) the individual etch-pits are resolved and the alignments are exactly parallel to the slip trace direction [101]. However, in some areas alignments deviate away from the slip trace direction by as much as 10 to 15 deg, this is evident in Fig. 4(b), and in Fig.

Jan 1, 1969

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months&apos; period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

By H. I. Kaplan, C. Laird

Pulsating contpresslon experiments have been carried out on coppev single crystals in order to test the adequacy of mechanisms which have been suggested for stage I cvack grouth when tension-compression loading is the mode of- applying stress. Although dejorrrzation continues slowly for many millions 01 cycles under Pulsating compression stresses both within slip bands formed in the first cycle and by the creation of new bands, the morphology of these bands is not typical of fatigue slip bands in general and neither initiation of cracks nor propagation of artificially induced cracks was observed. It is therefore concluded that 1) initiation and growth of cvacks in fatigue is a consequence of repeatedly reviersed, microplastic deformation rather than intermittent, unidirectional deforma-tion, 2) gvowth of- cracks in polycrystalline specimens FAILURE of a plain specimen subjected to cyclic tension-compression stresses is known to take place by two stages of cracking.1,2 The first stage is characterized by propagation along slip planes roughly at 45 deg to the stress axis, in the outermost layers of the specimen, and at a rate of the order of angstroms per cycle. The average macro orientation of a stage I crack is normally at right angles to the stress axis,3 however, except in a few cases, e.g., single crystals in suitable orientation, when both the micro and macro directions of propagation are at 45 deg to the axis. After a stage I crack has penetrated to such a depth that the stress on the remaining section of metal is significantly increased, stage II crack propagation succeeds stage I, at right angles to the stress axis both micro and macroscopically. Direct evidence of the processes occurring during a subjected to pulsating compression stresses is caused by the setting-up of local tensile stresses due to interactions between grains, and 3) both unslipping mechanisms and operation of the "plastic blunting process " within a single slip band are adequate descriptions 01- stage I growth, being fundamentally similar. The slip mode of a material, however, is considered to control whether unslipping or the plastic blunting process takes place. Thus materials of planar slip mode fauor unslipping while those hacing a wavy mode, and capable of cross slip, can fail in stage I by the plastic blunting process. Similarly, and perhaps more importantly, reversed torsion and tension-compression modes of applying stress may be expected to cause the unslipping mechanism and the plastic blunting process, respectively. single stress cycle4,5 shows that stage II crack propagation takes place by a repetitive plastic rounding and closing of the crack tip. This mechanism has come to be called the "plastic blunting process".6 On the other hand, the extreme smallness of the phenomena occurring in stage I growth prevents elucidation of its mechanism by direct observation. Many suggestions have been proposed for this mechanism,&apos;"-" most of them involving some kind of random or systematic unslipping process. It is possible, however, that the mechanism of stage I growth is essentially the same as that of stage 11, but occurring on a much smaller scale.6 In this situation, it has been observed that cracks propagate along slip bands comprising dislocation cell structures and bounded on either side by regions of different dislocation density and distribution." Since there is evidence that such bands are softer than their matrix, * it may be expected that the plastic blunting process occurs within a single slip band during stage I growth, rather than on two gross bands as in stage 11, when the acting stress is greater.= The blunting of the crack tip allowed by coordinated

Jan 1, 1968