Search Documents

By R. B. Burt, James A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1-the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2-power required for pumping, 3-pump selection. The basic factors for a given problem will include: 1-weight per unit of time of solids to be handled, 2-specific gravity of solids, for calculation of volume, friction and power, 3-screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4-shape of particle or some means of determining a friction constant, 5-effects of percentage of solids, 6-development of a viscosity factor to be used in the overall calculations, 7-calculation of the lower limits of pipeline velocities permissible, 8-calculation of total head, pump horsepower, and 9-setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble, phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; -14 +35 mesh, 11.4 pct; -35 +150 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The -150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble, content of the matrix, i.e., the +14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum -velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is, smooth and- polished because of the scouring, action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump, changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1952

By R. T. DeHoff, L. J. Buteau, J. Kronsbein

Network topology is introduced and used to describe sinter bodies at various stages of the sintering process. The matrices of incidence, loop-branch. tree-branch, and cut-branch are constructed and their relationship to the three-dimensional void space and the common two-dimensional bounding surface is established. The sintering body is assunzed to remain connected but this is not so with the void space. The topological invariants known as Betti numbers are related to this observed fact and provide parameters which measure the progress of the sintering process. They are extracted from the matrices by means of known algebraic operations. Experimental procedures are given which permit actual construction of the various matrices and determination of the Betti numbers by serial sectioning of the sinter bodies. A sinter body is produced by exposing a large number of metallic particles (0.00001 to 0.3 in. diam) to a temperature that is near but below their melting point. When these particles are maintained at such a temperature for a sufficient length of time, it is found that the interparticle contacts become welded. As time increases, these welds, often referred to as necks, grow. All of the space between the particles constitutes a single connected void; an ultimate consequence of sintering is the breaking up of the void into separated parts. A mathematical apparatus for describing the geometric characteristics of a sinter body at each stage of the process was first proposed by F. N. Rhinesl when he introduced the application of topology to this problem. He described the sinter body in terms of one of its topological invariants, the genus. The most important advantage of a topological description is invariance with respect to continuous deformations. This means that particle sizes and shapes need not be considered, resulting in considerable simplification and generalization of the geometric description. In the case of a sinter body, wherein the internal geometry is particularly complex, the simplification provided by topological concepts is absolutely essential. The important parameters in the Rhines model are the number of particles and the interparticle contacts. The invariant considered called genus is given by Euler's formula for the connectivity of two-dimensional surface of the sinter body. This surface includes the pore-solid interface. The Euler formula is G = C - P + 1 [1] where C = number of interparticle contacts, P = number of particles, and G = genus of the surface bounding the sinter body. In topology the term genus may be used to mean the number of self re-entrant cuts that can be made on a closed surface without dissecting it into more than one connected surface. Its use is restricted to the surface and does not apply to the three-dimensional volume enclosed or excluded by it. In the case of sintering, the volume enclosed by the surface is defined as the sinter body; the volume excluded will be referred to as the void space. There is an intrinsic reason for using genus as a characteristic number associated with a sinter body. The genus is related to the Gaussian curvature by the integral of the product of the principal curvatures taken over the entire surface of the sinter body, as given by

Jan 1, 1965

By F. D. Rosi

The slip and twinning behavior in extended titanium crystals were studied in some detail. The formation and appearance of coarse kink bands are discussed. Their crystallographic geometry was determined by X-ray analysis. A phenomenological interpretation of the complexities in kink band development is also presented. The critical resolved shear stress, coefficient of shear hardening, and plane of fracture were determined for several crystals extended at room temperature. THE slip and twinning elements observed in the room-temperature deformation of titanium were enumerated in a previous paper1 in which considerations were advanced regarding the nature and selection of these elements and their effect on the known mechanical properties of this metal. The present study concerns the crystallographic, microscopic, and mechanical aspects of flow in relation to the slip and twinning elements, and includes a prediction of slip systems, nature of slip and twin markings, inhomogeneities of plastic flow, and stress-strain characteristics. Unless otherwise noted, arc-melted titanium sponge (99.77 pct) was used in these experiments. The method of production of crystals, their dimensions, and the surface preparation for micrographic examination have been reported.&apos; For obtaining stress-strain characteristics, only those crystals which traversed the entire width of the specimen and were at least 8 mm in length were used. Tensile deformation of the crystals was performed with conventional grips for sheet specimens and a constant-stress loading beam, designed after the method of Andrade and Chalmers.&apos; The specimens were loaded by allowing sand to flow from a reservoir into a bucket suspended from the longer end of a balanced 6:1 lever arm at a rate controlled to load the specimen approximately 2 kg per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire strain gage, Type A-8, which permitted a reading accuracy of 2 microinches per inch. The formulas used in the evaluation of shear stress and shear strain, as in deriving the coefficient of shear hardening, are given by Schmid and Boasv n terms of the original orientation and change in length of the crystal. For calculating the critical resolved shear stress, the standard equation was used. The crystallographic nature of the unpredictable slip observed in a number of specimens was determined by the single-surface X-ray method of analysis as described in ref. 1. Experimental Results Prediction of Slip System: It was reported&apos; that room temperature slip in titanium takes place predominantly on {10i0} and in a <1120> direction, giving three potential slip systems. Hence, it should be possible to predict the operative primary system in the manner used by Taylor and Elam&apos; for alu- minum (i.e., the one with the greatest component of shear stress in the direction of slip). The stereo-graphic construction in Fig. 1 shows that this is true. In all cases, slip was found to occur initially on the (0110) plane and, in a number of cases, in the [21f0] direction. (The direction of slip was not determined for all orientations.) It follows that duplex slip can be expected when two slip systems are geometrically equally favorable for slip, as demonstrated in Fig. 2. In both crystals slip took place simultaneously on the (1700) and (olio) prismatic planes, as indicated by Fig. 2a and b. In the case of crystal B the movement of the specimen axis with increasing extension was toward the (10i0) direction, which represents the stable end orientation resulting from alternate slip on the [2ii0] and [1120] directions. This is analogous to the duplex slip process in face-centered cubic metals." Unpredictable Slip: In a number of crystals whose orientations were well within the operation of a single slip system, secondary slip occurred on planes not predicted by the criterion of maximum shear stress. Examples are shown in Fig. 3. In addition to

Jan 1, 1955

By J. L. Kenty, J. P. Hirth

The concept of a critical super saturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, is discussed with reference to vapor-solid nucleation. The necessary and sufficient conditions deduced for observations of this type of behavior are: 1) the nucleation rate must exhibit a sharp dependence on super saturation, 2) the growth rate must be sufficiently large that nuclei become observable in the time period of the experiment, and 3) the number of highly preferred nucleation sites must be small. Experiments reveal that the nucleation of silver on sodium chloride is visually detectable at all experimentally accessible super saturations and does not exhibit critical nucleation behavior. Failure to observe a critical super saturation is attributed to the insensitivity of nucleation rate to supersaturation as a consequence of the particular values of the contact angle and the surface free energy for this system. THE concept of a critical supersaturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, arises naturally in homogeneous nucleation theory. Experimentally this type of behavior has been found by Volmer1 and others for water and other low surface tension liquids, as reviewed by several authors.2&apos;3 The same type of behavior has been predicted and observed for heterogeneous nucleation of solids by Yang et al.4 and others,596 as also recently reviewed.2,7,8 In the work reported here on the heterogeneous nucleation of silver on NaC1, however, no critical super-saturation was found. Similar observations have been made recently for other systems.9-11 These results led to a reexamination of nucleation theory which revealed that there are conditions for which critical behavior is not predicted, either for homogeneous or heterogeneous nucleation. Although heterogeneous nucleation is of primary importance in this paper, some insight into critical behavior for such a case can be gained by considering homogeneous nucleation. Accordingly both types of nucleation theory are reviewed briefly. The requisite conditions for critical supersaturation behavior are then considered. The experimental results for the nucleation of silver on NaCl are presented and interpreted in terms of the theoretical presentation. REVIEW OF NUCLEATION THEORY There are essentially two approaches to nucleation theory, the so-called classical theory involving the concepts of bulk thermodynamics, and the statistical mechanical theory in which nuclei are regarded as macromolecules. The classical theory is based on the work of Volmer and Weber12,13 and Becker and. Doring14 and has been extended by Pound et al.15 The crucial assumption in the classical theory is that the small clusters or nuclei can be characterized by the same thermodynamic properties as those of the stable bulk phase. Thus, the nuclei are assumed to have a surface free energy, y, and a volume free energy of formation (relative to the vapor phase), ,, identical to that of the bulk. For deposition under low super-saturation conditions, the nuclei are large and this assumption is satisfactory. However, in many cases of interest, the nuclei contain only a few atoms and this assumption is highly questionable. The statistical mechanical models originated, for the specific case of a dimer as the critical nucleus, with the work of Frenkel16 and were extended later to larger sizes by Walton,17,18 Hirth19 and, more recently, Ht Zinsmeister. These models describe the nucleus in terms of a partition function, the estimation of which is tractable for clusters of 2 to 10 atoms, but extremely difficult for clusters larger than 10 atoms. Although the classical and statistical mechanical models are expected to apply for the limiting cases of large and small nuclei, both are uncertain for intermediate sizes. In this paper we shall treat only the classical model, recognizing that it is exact only for large nucleus sizes and regarding it as a phenom-enological description for small nucleus sizes. When analyses of experimental data using bulk properties show the nucleus size to be small, the resulting parameters should be regarded as largely empirical parameters describing the relative nucleation potency of the system. Considerable justification for the continued use of classical theory is provided by its general success in predicting nucleation behavior as a function of supersaturation and temperature. We emphasize that the qualitative features of the statistical mechanical models, particularly the critical super-saturation behavior that is central to the present work, are the same as those of the classical model. Of course, potential energy terms and surface partition functions replace the volume and surface energy terms of the latter model. The most recent versions of classical nucleation theory have been extensively reviewed.2,3,7 so that only the results are presented here. For homogeneous nucleation of a condensed phase from the vapor phase, the volume free energy change is ?Gv=vrT = =^ln£ [1] where v is the molecular volume of the condensing species. The supersaturation ratio,

Jan 1, 1970

By W. J. Carlson, S. M. Parmerter, I. Iwasaki

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates. It also deals with the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when an-ionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were affected most strongly by the level of starch, to a lesser degree by the pH, and virtually not at all by the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semitaconite could be readily attained with starch and calcium chloride. A previous article discussed some of the parameters that are important when various corn starches are applied to the soap flotation of activated silica from iron ores and to the flocculation of iron ore slimes.&apos; Methods of solubilizing the starches and the molecular size after mechanical and thermal treatments, as inferred from the viscosity measurements, were shown to influence the adsorption characteristics on iron ores, and the residual concentrations of both calcium ion and starch in the pulp liquor were in direct correlation with the flotation and flocculation behavior.2-4 The present article summarizes the results of more recent tests conducted to ascertain the role of starches and starch derivatives in various phases of iron ore beneficiation. The scope of this investigation has been extended to include not only anionic and cationic flotation, but also the flocculation and filtration of iron oxide slimes, the selective flocculation and partial upgrading of semitaconites, and the flocculation and clarification of magnetite-taconite tailings —all problems that are of vital importance to the iron ore industry of Minnesota. By combining a practical approach with adsorption studies and by using single-mineral systems5 in these research efforts, it is believed that the ultimate goal of developing a suitable modification of starch structure may be realized. The topics covered in this article are limited to the empirical aspects of the research program on the depressant activity of starches and products in the cationic and anionic flotation of silica and of their role in flocculation, water clarification and filtration. ANIONIC SILICA FLOTATION In the soap flotation of activated silica from iron

Jan 1, 1970

By A. T. Chatas

A description of the geometrical characteristics of spherical reservoir systems, a discussion of unsteady-state flow of such systems and examples of engineering applications are presented as backgmund material. The fundamental differential equation, a description of average spherical permeability and the introduction of the Laplace transformation serve as theoretical foundations. Engineering concepts are investigated to indicate particular solutions of interest, which are analytically obtained with the aid of the Laplace transform. These are numerically evaluated by computer, and presented in tabular form. INTRODUCTION A tractable mathematical analysis of unsteady fluid flow through porous media generally requires incorporation of a geometrical symmetry. The simplest forms include the linear, cylindrical (radial) and spherical. Most analytical endeavors have concentrated on cylindrical symmetry because it occurs more often in petroleum reservoirs. Nevertheless, some reservoir systems do exist that are better approximated by spherical geometry. Review of technical literature revealed but a single reference to unsteady spherical flow in petroleum reservoirs.l The motive and purpose of the present work was to remove this gap in technical information, and to provide the practicing engineer with some useful analytical tools. The mathematical details associated with the particular solutions of interest involved use of the Laplace transformation. Hurst and van Everdingen previously demonstrated the efficacy of this operational technique, and in many respects the present treatment was patterned after their earlier work.2 PRELIMINARY CONSIDERATIONS GEOMETRICAL CHARACTERISTICS Geometrically, a spherical reservoir system is defined at any instant of time by two concentric hemispheres whose physical properties of interest vary only with the radial distance. Every physical property is thus restricted to be a space function of only one variable: the distance along a radius vector emanating from the center. Such a system is composed of an outer region and an inner region, separated by a defined internal boundary. The inner region simply extends inward from this boundary, whereas the outer region extends outward from it to an external boundary. The position of the internal boundary is presumed fixed, so that the size of the inner region remains constant. On the other hand, the position of the external boundary at any given instant of time is determined by the distance into the system that a sensible pressure reaction has occurred, Thus, the external boundary may change position with time. It initially emerges from the inner region and advances outward to its ultimate position. When this ultimate position coincides with a geometric limit, the reservoir system is said to be limited. When it coincides with points subject to pressure gradients furthest removed from the internal boundary, yet short of a geometric limit, the system is said to be unlimited. In this investigation two different boundary conditions are imposed at the ultimate boundaries of limited systems. The first requires that no fluid flow occur across this boundary; the second that the pressure remain fixed at this boundary.3-5 UNSTEADY-STATE FLOW In a strict sense virtually all flow phenomena associated with a reservoir system are unsteady-state. The transient behavior of these phenomena requires accounting, however, only when time must be introduced as an explicit variable. Otherwise, steady-state mechanics may be used. Analytically, steady-state conditions prevail in a reservoir system only over that portion of its history when this relation is satisfied:

Jan 1, 1967

By C. E. Turner, J. R. Elenbaas, R. D. Grimm, J. A. Vary, D. L. Katz

A technique is presented by which well samples and core plugs of dolomite formations are classified by microscopic examination into seven different porosity grades. Quantitative values of porosity and permeability are determined for each grade by a statistical correlation of the core plug test data with the porosity grading system. These quantitative values are applied directly to the grades exhibited in the well samples for the purpose of estimating the reservoir void space for wells that were not cored. The procedure is described for estimating the gas reserves per unit area lor the South Hugoton gas field. but a reserve estimate for the field is not given. INTRODUCTION The miscroscopic examination of well sample; and the graphic recording of their lithologic qualities and other distinguishing characteristics of various geologic formations drilled is both a science and an art of long standing and wide application. Usually the primary objective of a geologist who "sits on the well" and examines the samples are: to identify the formation being drilled, determine the total depth, casing point. and completion interval. In most cases the porosity is described. if done at all, in general terms. such as: trace, scattered, fine, poor, fair, medium. good, excellent, or in some other relative terms. In fields where various geologists have examined samples and recorded observations on many wells considerable variations in lithologic terms and porosity descriptions occur unless there is primary effort to establish uniformity of logging observations and standards of recording observable porosity. When an estimate of the pore volume of a reservoir is made a geologic concept of the processes that control the magnitudes of porosity and permeability is developed by microscopic examination of well samples. The characeristics and appearances are then mentally related to rather general quantitative units of porosity based on physical core data from the same reservoir or on such data or experience in other reservoirs that have similar qualities. The reliability of such estimates depends largely on the variations of the lithology of the formations, the geometric properties of its void system. the extent of comparisons of sample appearances with porosity data, as well as the uniform recording of all relevant characteristics. This statement is particularly significant for dolo-mitized limestone formations of substantial thicknesses and heterogeneity such as the Permian Dolomites of the Hugoton gas field. Jn this field, as well as in most of the Permian Dolomite fields, the producing formations are of relatively great thicknesses in which the porosity and permeability of the reservoir varies substantially in all directions, depending on the crystalline structure. degree and kind of impurities, kind of fossils anti cementation thereof, degree of dissolution. and fracturing. The variations of the lithologic texture of the dolomites and post deposition alterations have resulted in porosities and permeabilities of such magnitudes that only a part of the gross thickness can be counted as "pay." At the time of this study insufficient gas production had been experienced to apply the pressure decline production method in the South Hugoton Field and the electric logs are not definitive enough. The problem of estimating gas reserves in the south part of the Hugoton Field is primarily one of determining the pay thickness and porosity from well samples and core data. The area studied embraced all that part of the field lying south of an east-west line through Guvmon, Okla., anti containing approximately 1.000,000 acres. This paper describes a technique of correlation of physical core data with well samples so that quantitative values of pay thickness, porosity. Permeability, and connate water may be assigned to well samples that are representative of a given interval, and thereby permitting the estimation of gas reserves lor a given unit area. The procedure was developed by a uniform microscopic qualitative porosity grading of the dolo. mite core plugs.. and relating these grades to the respective physical core data on a statistical basis The well sample-were also graded in a Similar manner in order that the quantitative values established lor the core plugs could be applied to the well Sample for wells that were not cored. GRADING OF DOLOMITE A group of experienced geologists was given the assignment of examining the samples on all wells in South Hugoton in order that they could log their observations in a uniform and standardized manner and grade the observed porosity so that it could be related quantitatively to the core data. The group initiated the study 011 chips from cores which bad been tested for porosity and permeability. This study continued until all of the geologists developed a common knowledge of lithologic terms and of the characteristic appearances of the samples and their relations to measured porosity. The characteristic appearances of the dolomite samples under twelve-power magnification as related to their qualitative porosities afforded a classification of the dolomite into :even grades of porosity, ranging from dolomite of no-visible porosity under twelve-power magnification to dolomite of excellent porosity. The assigned grade for a specific 10-ft interval is a weighted average of all visible grades of porosity exhibited by the cuttings representing that interval. The porosity characteristics were recorded by a color graph adjacent to the lithology column in conjunction with a numerical system for further definition of relative porosity as shown in Fig. 1. The three vertical lines to the right of the lithology column each represent 33 1/3 per cent. which lines were used to record the percentage of the samples, for any particular interval. that showed porosity under the microscope. The colors were used to denote actual pore size. i.e., orange. blue and I-ed for pore diameter of one-fourth or less. one-fourth to one-Ilalf. and greater than one-half millimeter, respectively. The area colored 1)). one or more colors represents the percentages of the samples exhibiting pores of the respective size or sizes. The numerals from one to six inclusive shown on the log in

Jan 1, 1952

By L. F. Porter, G. J. Dienes

The effect of netltron irracliation on mart ensite transformation in the iron-nickel system was studied by means of electrical resistance and magnetic induction measuremertts. Irradiation lowers the M8 temperature of the allay, causes changes in the electrical and magnetic properties of the high-temperature phase which indicate either an accelemtion of phase separation or a clustering of nickel, and enhances strain recovery on specimens partially transformed to martensite prior to irradiation. Possible mechanisms to account for the effects; are discussed. 1 HERE is a good deal of evidence to indicate that neutron irradiation is capable of affecting phase changes in metals and alloys. While the mechanism of the effect often is not well understood, such studies hold promise of improving our understanding not only of irradiation damage but also of the phase changes involved. To date systematic and detailed investigations have been made of the influence of nuclear radiation on order-disorder transformations in the copper-gold, nickel-manganese, and copper-zinc system, and on precipitation reactions in the copper-iron, nickel-beryllium, and copper-beryllium system.&apos; These solid-state reactions are diffusion controlled and the results can be explained largely on the basis of enhanced diffusion due to the presence of irradiation produced vacancies. Reversion of low-temperature eutectoid phases to the high-temperature phase has been observed in the fissionable uranium-molybdenum and uranium-niobium systems.2 Here it is necessary and logical to postulate a displacement spike mechanism to account for the effect. The only case of irradiation induced diffusionless transformation in metals is the allo-tropic transformation of p to a tin reported by Flee-man and Dienes. 3 They found that neutron irradiation markedly decreases the incubation time for transformation, but the mechanisnl is not well understood. Another diffusionless transformation which one might expect to be influenced by neutron irradiation is the martensite transformation. This transformation is known to be sensitive to strain, structural hardening, and the presence of imperfections.6,7 Since the transformation is diffusionless, one also

Jan 1, 1960

By J. W. Snavely

THE high tension belt conveyor is introducing a new and tremendously expanded era of low cost bulk material handling. High tension belt conveyors are generally those installations involving very long centers, high lifts, or drops, in which the belts are stressed up to their maximum tension values, and further, where the belt construction provides tension capacity far beyond what is possible with conventional belt constructions. With these high tension installations, the magnitude of the forces involved demands careful refinement of accepted design practice in order to achieve optimum balance of all factors. No attempt will be made to evaluate the relative merits of belt conveyor haulage with other means of transportation. For present purposes, it is assumed this has already been done in favor of belt conveyor. Neither will any attempt be made to evaluate the various conveyor belt constructions now available or to balance the advantages of various types of mechanical equipment. It is also assumed that the basic haulage information on which the conveyor design is based is accurate and complete. A sustained maximum, uniform load on the belt at all times must be achieved through proper feed control and the use of adequate surge storage to level the peaks and valleys of any varying demand for the material being handled. General Belt Capacity Considerations The belt conveyor capacity tables published by various belting and conveyor equipment manufacturers vary to a considerable degree, and the ratings given are quite conservative. Of necessity, these published ratings are based on the handling of average materials under average conditions. In applying a high tension belt, all possible capacity from the belt must be obtained in order to hold its width to a minimum and thereby limit the initial cost. Two factors are involved, loading to maximum cross section area and traveling at a maximum practical speed. Belt Loading: Proper treatment of the loading of the belt will result in maximum cross section to the load, and published capacity ratings can be exceeded, sometimes by appreciable margins. On the 10-mile conveyor haul used in the construction of Shasta Dam, California, although the rated capacity of the belt line was 1100 tons per hr, at times the system handled peak loads of 1400 tons per hr, almost 25 pct better than the rated capacity. One of the large coal companies has been able to exceed rated capacity by as much as 50 pct. Loading conditions which must be controlled are: 1. Large lumps must be scalped off and rejected or the load must be primary crushed before being placed on the belt. 2. The material weight per cubic foot must be accurate, must be known for all the materials being handled, and must be known for the complete range of conditions of the individual material being handled. Long centers and high lifts magnify small differences into serious proportions. 3. Uniform feeding to the belt is most important. Various types of feeders are available, which can be used to place a constant predetermined volume of material on the belt, or, where an appreciable range of material weight exists, through electrical control actuated by current demand, to place a predetermined uniform tonnage on the belt. One long slope belt in a coal mine in Pennsylvania is being fed at three separate stations with the controls so arranged that whenever the maximum load is going onto the belt from the first station, the other two stations automatically cut out. Whenever the load from the first station drops back, the other two stations again automatically cut in. 4. Careful design of the chutes and skirts is necessary to get the load centered on the belt with a minimum of free margin along each edge. Some free margin at the edge of the belt is necessary to prevent spillage, but if the load can be kept accurately centered, this free margin area can be reduced, and more material can be carried on the belt. What can be accomplished in this respect will vary widely, depending on the nature of the material being hauled. The chute and skirt design must also protect the belt. 5. The design of chutes and skirts should also get the load traveling in the same direction and close to belt speed, so that the load comes to rest on the belt as quickly as possible. The design of the chutes and skirts is worthy of careful study, and after a system is put into operation it should be experimented with to get the best results. Belt Speed: High belt speeds should be used in high tension work. Obviously, high belt speeds enable haulage on a narrower belt, reducing initial cost. The major portion of belt wear takes place at the loading point and around the terminal pulleys. The

Jan 1, 1952

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of&apos; (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.&apos;-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "&apos;12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger&apos;s terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By J. V. Gluck, Ping-Wang Chiang

The tellurium-rich region of the Sb-TI-Te ternary system was investigated by means of DTA, metallo-graphic, X-ray, and electron beam microprobe techniques on the sections Sb2Te3-T12Te3, SbTlTe2-Te, SbT1Te2-Sb2Te3, and SbTlTe2-T12Te3. The phase behavior of this region is summarized in terms of four ternary invariant reactions and a schematic reaction diagram is suggested. Isopleths for the sections SbT1Te2-Sb2Te3, Sb2Te,-T12Te3, and SbTlTe2-Te were constructed, and a schematic diagram of the projections of the liquidus lines and invariant planes is presented. No evidence was found to support the existence of the ternary compound "SbTlTe3", or pseudo-binary behavior of the section T12Te3-Sb2Te3, as reported by Borisova and Efremova. Electrical conductivity, Seebeck coefficient, and thermal conductivity measurements were made at room temperature on fully annealed samples. 1 HE phase relationships in chalcogenides are often complex and difficult to resolve, particularly since the approach to equilibrium is a rather slow process. For example, the phase diagram of the T1-Te binary system was in doubt until clarified by Rabenau et al.,1 the phase fields at compositions near Bi2Te3 in the Bi-Te binary system have only recently been satisfactorily elucidated by Glatz,2 and there may still be some question as to the extent of the Sb2Te3 field in the Sb-Te system.3-5 In ternary systems, the existence of the compound "AgFeTe2" was the subject of a number of conflicting reports6-8 and the stoichiometry of the composition "AgSbTe2" was in doubt for a period of time.9 Recently, questions have arisen regarding the existence of certain compounds in the ternary systems Bi-Tl-Te10-14 and Sb-Tl-Te.15 The impetus for studies of these latter systems stemmed from the report of Borisova et a1.10 of a congruently melting ternary compound, "BiTlTe3", which apparently had extremely favorable thermoelectric properties for room-temperature cooling applications. Attempts by other investigators to produce the compound or confirm the transport properties proved to be unsuccessful.12-14 Recently, Chiang and Gluck14 reported studies of the phase relations in the tellurium-rich region of the Bi-T1-Te system which indicated that the section T12Te3-Bi2Te3 was not pseudobinary as suggested by Borisova et a1.10 The contention of Spitzer and sykes12 was supported that the composition "BiT1Te3" was multiphase, with the primary constituent actually being BiTlTe2, a compound whose existence has been well demonstrated.16,17 The investigation reported in the present paper was prompted by a later report of Borisova and Efremova15 on a similar study of the section T12Te3-Sb2Te3 from the Sb-T1-Te system. They also claimed this section to be pseudobinary, and that a ternary compound "SbTlTe," was formed peritectically. Some "preliminary" crystallographic data were given for the compound and thermoelectric transport properties were presented. In view of the questions concerning the behavior of the Bi-T1-Te system and the existence of the compound "BiT1Te3" it was suspected that the Sb-T1-Te system might behave in a similar fashion, particularly in light of the known existence of a compound SbT1Te2, iso-structural with BiT1Te2.17 Consequently, an investigation was undertaken to clarify the phase relationships in the tellurium-rich region of the Sb-T1-Te system. It is the purpose of this paper to present the results of this study, including a representation of the phase relations, isopleths for various composition sections, and the determination of some phase compositions and transport properties. EXPERIMENTAL PROCEDURES Commercially available high-purity (99.999+ pct) elements, purchased from the American Smelting and Refining Co., were used for the sample preparation. All samples were made from thoroughly mixed powders of previously prepared master alloys: SbTlTe2, Te, Sb2Te3, and T12Te3. Stoichiometric quantities of the constituents for each 10-g sample were weighed into a specially cleaned fused silica tube and sealed under a vacuum of better than 5 x 10-5 torr. The sealed constituents were fused and reacted at 650° to 750°C for at least 4 hr under continuous agitation in a "rocking" furnace, and the resulting product was air-cooled. The tube was opened and the sample was ground to a powder. A portion of the powder was rebottled in a DTA tube under vacuum, and the rest of the material was similarly resealed in a separate tube, re-fused in the rocking furnace, and again cooled to make the ingots for electrical and microstructural studies. All samples were subjected to further heat treatments as discussed in the section on experimental results. Each DTA tube was made of 7-mm-OD fused silica tubing with a concentric 2-mm-ID depression about 4 mm long formed in the bottom to accommodate a thermocouple. The size of a DTA sample was 0.5 to 1.0 g. An Aminco Thermoanalyzer whose accuracy was within 2°C18 was used for the DTA measurements. The metallographic samples were prepared by conventional techniques. A solution of FeCL dissolved in a methanol-HC1 mixture was found to be the most satisfactory etchant. Electron beam microprobe scanning and point-count examinations were made on polished and unetched samples using an ARL Electron Microprobe at an electron beam voltage of 20 kv. The detectors were set to receive characteristic La1 radiation. Calibration standards of the pure elements were incorporated in each sample mount; quantitative point counts were calibrated by a method similar to Ziebold

Jan 1, 1969

By A. M. Sarem, J. M. Campbell

Molecular refraction is introduced as a new and improved third parameter for prediction of the PVT behavior of hydrocarbon systems. This parameter, characterizing the complex as well as the pure hydrocarbon systems (1) is a direct measure of London dispersion forces which affect the PVT behavior; (2) can be measured directly, accurately and easily for complex as well as pure hydrocarbon systems; (3) varies significantly between the reference substances thus allowing accurate interpolation of PVT properties; and (4) has a fundamentally sound basis. Molal average molecular refraction was used with the pseudocritical mixing rule proposed by Leland and Mueller to predict the molal volume of liquid and vapor for 84 published data points on nC4-nCI0, Cl-nC5, Cl-nC4-nC10 systems in the region of coexisting vapor-liquid and at the critical point. The same technique was applied to predict the densities of liquid hydrocarbon mixtures in the two-phase and single-phase regions near the critical point for seven different systems each having different properties of the heptanes-plus fraction, but all simulating the fluids of either gas-condensate or volatile oil reservoirs. A modification of the Leland-Mueller mixing rule for the determination of pseudocritical properties is also presented which yields more accurate liquid density predictions than the original form when used with the proposed third parameter. INTRODUCTION The PVT behavior of multicomponent systems has received widespread attention in the literature in recent years. A large portion of the reported work has stemmed from attempts to overcome the inherent difficulties encountered when using the standard compressibility-factor chart which shows 2 as a function of reduced temperature T, and and reduced pressure p,. This chart assumes that z, is constant for all systems. The error in this assumption is not pronounced for pipeline-type gases high in methane and low in heavy ends, particularly when contained at moderate pressures. For such gases the error in the calculated z is usually less than 2 to 3 per cent. However, the reliability of this approach becomes somewhat nebulous for gas condensate and volatile oil systems at high pressure. One logical approach has been to recognize the variation of 2,. This idea was first suggested by Meissner and Seferianl and used by Lyderson, Greenkorn and Hougen2 to prepare extensive tables of thermodynamic properties. Other third parameters have been proposed by Stockmeyer, Kihara, Riedel, Lightfoot, Bloomer and Pitzer. These were tested by Satter and Campbel13 for many gas mixtures and it was shown that they were inter-related. All of these third parameters have a common fault — they cannot be directly evaluated for the heptanes-plus fraction. Consequently, one necessary requisite of an improved method for predicting the density of multicomponent hydrocarbon systems, was development of a third parameter that could be evaluated for that fraction. PREVIOUS MULTICOMPONENT DENSITY PREDICTION METHODS Sage and Lacey4 suggested a method of using partial molal volumes for computing the density of hydrocarbon gas mixture for pressures to 3,000 psi. In this technique, they approximate the complex multicomponent gaseous mixtures by a quarternary system of methane, ethane, propane and butane. Sage, Hicks and Lacey5 suggest a method of using partial molal volumes for computing the density of hydrocarbon liquids. The results agree within 3 per cent of the experimental values. However, the composition range is limited to about 10 per cent by weight of methane. Consequently, this correlation does not cover the low-molecular-weight liquid similar to natural gasoline and high-pressure gas condensates.

Jan 1, 1966

By P. Gordon

An isothermal jacket microcalorimeter, supplemented by metallographic, microhardness, and X-ray measurements has been used to study the isothermal annealing of high purity copper after room temperature tensile deformation. The amount of stored energy released during annealing has been measured as a function of deformation in the range 10.8 to 39.5 pct elongation. The data have shown the major heat effect to be associated with recrystallization and have allowed an analysis of the recrystal-lization kinetics and the calculation of activation energies of recrystallization. WHEN a metal is deformed plastically, some of the energy expended is dissipated as heat during the working process, while the remainder is stored within the metal in the form of lattice distortions and imperfections. During subsequent heating of the metal, the distortions and imperfections can be largely annealed out and the associated stored energy released as heat. It is apparent that measurements of the evolution of stored energy during such annealing may produce important information concerning the nature of the annealing mechanisms and the imperfections involved. Some excellent studies of this type have been made in the past, notably those of Taylor and Quinney,&apos; Suzuki,2 Bever and Ticknor,3 Borelius, Berglund, and Sjöberg,4 and Clarebrough et al.5,6 None of this work, however, employed isothermal techniques, with the exception of the Borelius studies&apos; in which only the early annealing stages were investigated. Since isothermal measurements, as compared with heating or cooling curve, have the merits that 1—they reveal the kinetics of a process more clearly, 2—the results obtained are more easily applied to theory, and 3—most fundamental investigations of annealing using techniques other than calorimetry have been carried out isothermally, it was considered important to apply calorimetry to the study of the isothermal annealing of metals. Accordingly, an isothermal jacket calorimeter of the Borelius type,&apos; supplemented by metallographic, hardness, and X-ray measurements, has been used to study the annealing of high purity copper after room temperature tensile deformation. Experimental The microcalorimeter has been described fully elsewhere." Briefly, the specimen to be studied is placed in a constant temperature environment of virtually infinite heat capacity achieved, as shown in the drawing of Fig. 1, by means of a vapor thermostat. A high thermal resistance is provided between the sample and the environment and a sensitive differential thermopile (see Figs. 2 and 3) arranged with half its junctions in contact with, and thus at the constant temperature of, the environment, and the other half in contact with the sample. A reaction in the sample develops a small difference in temperature, AT, across the thermopile, which is followed by a recorder-galvanometer set-up as a function of time, t, and is converted to reaction heat per unit time, P, by the use of the equation AT P=a?T + b AT dt The constants, a and b, in Eq. 1 are determined by a simple calibration, making use of the Peltier heat developed by a small current run through the junction of a thermocouple located in an axial hole in the specimen (Fig. 2). In its present form, the limit of sensitivity of the calorimeter is a heat flow of 0.003 cal per hr. The copper used was the spectroscopically pure metal supplied by the American Smelting and Refining Co. in the form of 3/8 in. diam continuously cast rod, reported to be 99.999+ pct Cu. A small amount of the copper was available at the start of this work and is referred to hereafter as lot A. A second batch, lot B, was obtained later, most of the results described subsequently being for this lot. As will be seen, there is some indication that lot A was somewhat purer than lot B, but it is not known whether this difference was present in the as-received metal or arose during subsequent handling. The two lots of copper were remelted and cast into two 1½ in. diam ingots in vacuo, using high purity graphite crucibles and molds. The ingots were upset several times to break up the large cast grains, and then rolled and swaged to rods 0.391 in. in diameter, using several intermediate anneals with about 40 pct reduction in area between anneals. The penultimate anneal was 2 hr at 350°C. X-ray examination showed no marked general preferred orientation in the resulting rods. The grain structure typical of the two rods is shown in the micrograph of Fig. 4." It was found to be virtually im- possible to get an unambiguous measure of the absolute grain size in the two annealed rods because of the profusion of annealing twins and the lack of regularity of the grain boundaries. However, counts of the number of boundaries intersected per unit length along a random line on a polished section, making a correction for the proportion of boundaries (about half) estimated to be twin boundaries, gave a figure of about 0.015 mm for the average grain diameter. The grain size of the rod from lot A was about 5 pct smaller than that from lot B. The rods were cut into 1 ft long bars and these deformed in tension at room temperature to various total elongations in the range 10.8 to 39.5 pct. A strain rate of 1 pct per min was used. The deformed bars were then stored in a dry ice chest until such time as samples were to be cut from them. Five bars deformed as indicated in Table I were used for the subsequent tests. In all cases, all the calorimeter.

Jan 1, 1956

By B. K. Larkin, H. R. Bailey

A model Of heat flow in an underground combustion process is studied. This model includes convection effects and thus is more general than previous studies which considered conduction as the only mechanistn for heat transfer. Both linear (tube run) and radial (field application) geometries are considered. The effects of ignition heaters, vertical losses and finite source width are considered for the linear case. The results are in the form of equations and are presented in graphical form for a number of cases. Convection effects increase frontal temperatures about 25 per cent over those computed for conductive transfer for typical field operating conditions. This increase in temperature is a result of heat being transported toward the front by the injection gas. Even greater temperature increases are realized as the per cent oxygen in the injection gas decreases. It is well known that compression costs are of considerable importance in estimating the economic feasibility of underground combustion. By assuming an ignition temperature for the combustion fuel, predictions of limiting conditions on fuel density and injection rate necessary to sustain the combustion zone are made. For typical field conditions, at least 0.75 lb/cu ft of fuel are needed with air as the injection gas. If the injection gas is 10 per cent oxygen and 90 per cent nitrogen, this figure is 0.69 lb/cu ft. INTRODUCTION The possibility of increasing oil recovery by underground combustion has been considered for many years. Recent field tests indicate that the underground combustion process is technically feasible. The economic feasibility depends to a large extent on the amount of air which must be injected to sustain combustion. Prediction of the success of employing underground combustion in a particular reservoir must be based on existing field tests, laboratory tube runs"&apos; and solutions of mathematical or analog models. Vogel and Krueger5 devised an electrical analog of the heat transfer problem in an underground combus-ion process. They considered the problem of heat conduction from a cylindrical source with increasing radius assuming no vertical losses. Bailey and Larkin and Ramey solved the corresponding problem including vertical losses by considering a mathematical model of the conduction process. Ref. 9, 10 and 11 also present information related to the subject study. The present paper generalizes these results to include both conduction and convection mechanisms for heat flow. A model of the conduction-convection process is described. The partial differential equations governing this model are written and solved for a number of cases of interest. The formulas are evaluated and the results are presented graphically. A CONDUCTION-CONVECTION MODEL Description of the Model A number of models are employed in this paper, each of which approximate a particular physical situation depending on the geometry, i.e., linear or radial flow, the type of vertical heat losses, the nature of the source, etc. The geometry for both the linear and radial case is shown in Fig. 1. A particular linear model is described in this section, and variations from this model are described in later sections of the paper. Consider a homogeneous, semi-infinite porous prism with lateral sides insulated as shown in Fig. 1. The left end, x = 0, is heated for a time t, with a plane heater supplying a constant heat flux and during this time; gas (nitrogen) is passed through the pores of the prism at a constant mass flux. At time t, the heater is turned off and air is injected in place of the nitrogen. This causes combustion to take place, and a uniform source of width 1 is formed which moves at a constant velocity v, to the right. The frontal velocity v, is related to the gas velocity v,, through stoichiometric considerations

By B. C. Burgess

IN the first edition of this volume,44 feldspar was introduced as "the I commonest mineral of the crystalline rocks," usually in small grains associated with other minerals and commercially produced only from pegrnatites. Now other crystalline rocks, such as alaskites and granites, have become present or potential sources of feldspar. In addition, feldspar has encountered very vigorous competition from such substitutes as nepheline syenite and aplite. COMPOSITION AND PROPERTIES The feldspars form a group of which the principal species are orthoclase, microcline, albite, and anorthite. These are aluminum silicates of potassium, sodium and calcium. There are also a barium feldspar, celsian, and barium orthoclase feldspar, hyalophane, rarely found and of no commercial importance. None of the minerals in the feldspar group are found pure or nearly pure. The potash feldspars, orthoclase and microcline, nearly always contain some albite (soda microcline, an- orthoclase); the soda feldspars usually contain some anorthite (lime feldspar). There is a series of soda-lime feldspars known as plagioclase in which the albite and anorthite molecules replace each other in varying proportions from albite through oligoclase, andesine, labradorite, and bytownite to anorthite. Theoretical chemical composition of the principal feldspars is given in Table 1. The Whiteware Division of the American Ceramic Society sub- mitted a list of definitions of ceramic terms, in April 1947, for use in technical literature. For feldspar it gives: "A group of igneous minerals consisting chiefly of the aluminum silicates of potash, soda and lime, in which one base generally predominates." Commercial feldspars are intergrowths of at least two species of feldspar, which occur associated with one or more accessory minerals such as quartz, muscovite, biotite, garnet and tourmaline as well as with small but varying proportions of the decomposition product, kaolinite. An intergrowth of quartz and feldspar frequently contains

Jan 1, 1949

By A. Ghosh, T. B. King

The kinetics of the discharge reaction: 20&apos;- (in silicate melt) = O,(g) + 4e- at a platinum anode in lithium silicate melts have been studied al 1350°C by galvanostatic methods. Plots of the sleady-state overpotential, q, as a function of the logarithm of the current density, i, showed injlections and were linear only at high current densities. The value of the overpotential was influenced by bubbling gas through the electrolyte. The ocer potential was also studied as a function of time. The rise and decay of overpotential were very slow processes. At low current densities transport is the likely rate-controlling process but at high current densities passivation of the electrode, Presumably by an oxide film on the surface, seems to be a contributory functor. IT is well-established that molten silicates behave as electrolytes&apos;5 and, except in a few cases,6 conduction is entirely ionic. Moreover, it is supposed that a possible, and perhaps predominant, mechanism for phase boundary reactions between metals and slags is similar to that in corrosion whereby anodic and cathodic processes occur at unrelated sites, the metal serving to conduct electrons.1&apos;8 Thus electrochemical studies of some slag-metal reactions would seem to be a useful way to diagnose the rate-controlling steps in the overall reaction. The electrochemical method is, in principle, a better diagnostic tool than the direct chemical method for the following reasons: 1) The partial electrochemical reactions, which are simpler than the overall reaction, may be studied individually. 2) The rate of reaction can be controlled at will and independently of the concentrations of reactants. 3) Fast reactions can be studied by relaxation methods.&apos; Esin and his coworkers5&apos;10"12 have pioneered such studies in silicates and have deviloped some ingenious techniques. Not all of their findings, however. can be accepted without a good deal of further work. In this investigation, the kinetics of the oxygen discharge reaction: 202- (in silicate melt) = Oz(g) + 4e- [I] at a platinum electrode were studied by both steady-state and transient galvanostatic techniques. Interest in this reaction was first developed as a result of the findings of Fulton and chipman13 that the reduction of silica, in a silicate slag, by carbon, dissolved in liquid iron, is a very slow reaction. Subsequent work, for example, by Rawling and ~lliott,&apos;~ has demonstrated that the reaction under these conditions must be slow, because the rate is limited by diffusion of oxygen in the iron to the metal-crucible phase boundary at which a CO bubble may be nucleated. Further work by Tarassof,&apos;~ in which the reduction of silica by aluminum dissolved in copper was studied, has shown that under these conditions, where carbon monoxide evolution is not involved, control of the reaction rate resides in diffusion of silica in the slag phase. However, there is no practical way of inducing sufficient convection in the system to make it clear that the phase boundary reaction is indeed fast. The overall reaction of silica reduction involves the discharge of silicon ions at cathodic sites and oxygen ions at anodic sites. In the examples cited, the discharged ions are dissolved in a liquid metal. In the present study of oxygen ion discharge, gaseous oxygen may be evolved at high current densities or oxygen may simply dissolve, possibly as oxygen molecules, in the silicate at very low current densities. The discharge of an oxygen ion at an anode must, in silicates less basic than the orthosilicate composition, be preceded by a reaction in the vicinity of the electrode, such as: which makes oxygen ions available. Platinum was chosen as the working electrode since it is comparatively inert to oxygen and is, therefore, expected to come rapidly into equilibrium with the electrolyte and with gaseous oxygen. Minenko, Petrov, and Ivanova16 have measured the electromotive force at a platinum electrode in molten silicates as a function of the partial pressure of oxygen in the atmosphere, the concentration of oxide ions in the melt, and the temperature. They found platinum to behave as a reversible oxygen electrode. At two different oxygen pressures, Po2 (I) and Pq (11). the electromotive force is given by: where F is the Faraday constant, equal to 23,060 cal per v equivalent, indicating that the electrode reaction is as written in Eq. [I.]. Platinum has been similarly used in molten silicates by other inve~ti~ators. "&apos;~~ In this investigation platinum was used only as an anode, since a current deposits other elements on its surface and changes its characteristics.

Jan 1, 1970

By H. Ries, R. E. Somers

Bodies of pyritic ore in schistose rocks have long been known in different parts of the world. The several occurrences resemble each other in being usually of more or less lenticular shape, inclosed in walls of schist or gneiss, and carrying pyrite, chalcopyrite, and pyrrhotite in varying proportions, as the chief ore minerals. The deposits differ, however, in that sometimes one, sometimes another, of the three sulphides mentioned may predominate. The orebodies in general are more or less closely conformable with the schistosity of the wall rocks, although in cases this may not hold true. The boundaries may or may not be sharp, but in general are fairly distinct. The lenses vary in size, may occur singly, or in groups; in the latter case they may be in line, overlapping, or occasionally parallel. Pinching and swelling of individual lenses is not uncommon. The genesis of these pyritic bodies has provoked much discussion, and they have been variously classed as sedimentary, igneous intrusions, hydrothermal replacements or impregnations, etc. Indeed, in some cases different geologists have most positively assigned widely diverse origins to the same deposit, as in the case of Rio Tintol and Rammels-berg.2 It is true that in the light of modern criteria, we have been able in a few cases to decipher clearly the process of origin and so there seems no. doubt now regarding the genesis of the deposits at Rio Tinto, Spain;3 Rammelsberg, Germany;4 Ducktown, Tenn.;5 southwestern Virginia;=

Jan 1, 1918

By W. R. Hibbard Jr., R. W. Guard, N. G. Ainslie

Evidence is presented that copper-base solid solutions of different solutes having equal grain sizes, no preferred crystal-lographic orientation, equal electron-atom ratios, and, within experimental scatter, identical initial yield strengths, need not have identical stress-strain curves at strains larger than about 0.04. The stress-strain behavior is rationalized in terms of the proposed Suzuki chemical interaction between solute atoms and extended dislocations using what is thought to be a somewhat different means of representing stress-strain data. ALTHOUGH the effect: of alloying element upon the strength characteristics of sold solutions is a subject which has received considerable attention in the past, the exact relationships between the common deformation parameters and certain common variables are not really known in some cases. As a result some of the experiments reported in the literature in which these variables are inadequately controlled lose some of their persuasion regarding underlying principles. Nonetheless, facts are known which bear pointing up: When the true stress, a, and true plastic strain, E, of tensile deformatic~n are plotted on a double logarithmic coordinate system, one may observe a straight-line relationship at strains greater than 0.02. The form of the curve in the linear region is given by a = Ken! where a represents true stress, E, true strain, and K and tn, constants. If the relationship holds, K and m define the flow characteristics of the material being tested. m and K, however, may vary with other parameters. Hollomon found that in a-brass, m is influenced by grain size. French and HibbardZ found in alloys of copper that inverse relationships existed between m and 1) the solute concentration for a given solute, 2) the 0.01 yield strength, and 3) the constantK. Lacy and Gensamer3 observed (du/d~) (= U/Em) to increase with increasing values of K in systems of alloyed ferrites (although with considerable scatter of data which may be attributed to uncontrolled grain size). Brick, Martin, and Angier* deduced in copper-base alloys a straight-line relationship (with some scatter) between the change in the Dph number due to solid-solution strengthening and the change in the Dph number due to work hardening which suggested that copper-base alloys having equal yield strengths might have identical stress-strain curves in the plastic flow regions. French and HibbardZ concluded that the yield strength of copper-base solid solutions is the proper basis for comparing the effects of solute elements. Also, Allen, Schofield, and ate&apos; showed that, within their experimental variation, copper-base alloys of zinc, gallium, germanium, and arsenic having the same electron-atom ratios have the same true-stress true-plastic strain curves. Dorn, Pietrokowsky, and ~ietz&apos; also found that with aluminum-base alloys the stress-strain curves in the flow regions are approximately the same if "equivalent" concentrations of alloying elements are used. Solute valence and lattice parameter distortion were the parameters used to determine equivalency. The present report describes an investigation in which an attempt was made to obtain copper-base solid-solution alloys of four solute elements having within close tolerances equal grain sizes and yield strengths, and to see if the level of yield strength does indeed define the flow curve regardless of solute type. During analysis of the data certain unexpected features of the stress-strain curves became apparent which gave rise to some speculation and are discussed at length in the paragraphs that follow. EXPERIMENTAL PROCEDURES Alloy Preparation—Using the data of French and HibbardZ as a first approximation, four different binary copper-base alioys were designed so as to have the same yield strength. In addition, other alloys were prepared in which the solute aoncentrations varied slightly from those calculated above so as to span a range of yield strengths, see Table L The yield strengths of all alloys prepared except the copper-tin alloys were subsequently found to Lie fairly close to one another. The copper used in the alloys was produced by the American Smelting and Refining Co. and was of very high purity (99.999 pct). The alloy additions and their initial purities are as follows:

Jan 1, 1960

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,&apos; located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI&apos;S were approximately the same as PI&apos;S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949