Search Documents

By J. J. Gilman

WHEN a cleavage crack that is moving through a crystal intersects a screw dislocation, a jog is created in the crack front. As the crack continues to move, the jog leaves behind a cleavage step. This mechanism was proposed by Amelinckx and Votava,' Pratt, bnd Gilmanh t about the same time. At that time the evidence for the mechanism was largely indirect. Other evidence has been presented by Low, Bilby and Smith,5 and Forty.' It is the purpose of this paper to present more direct evidence of this mechanism and to show that observations of cleavage steps can be used to detect screw dislocations. Experimental Lithium-fluoride crystals that were purchased from the Harshaw Chemical Company, as well as natural mineral crystals and metal crystals, were used in the experiments. Although cleavage steps can be observed on transparent crystals with a metallurgical microscope, the contrast is poor. Marked improvement in the contrast is obtained by depositing thin (1000A) films of silver or aluminum onto the surfaces. The contrast also can be improved by using a phase-contrast microscope, but the simpler silvering method gives just as good results. Tolansky interferometric microscopy, and electron microscopy were used to measure the heights of cleavage steps. The etching techniques developed by Gilman and Johnstonh ere used to detect dislocations in the LiF crystals. Results The dislocations that create cleavage steps can originate in three ways: a) They can be grown into crystals b) They can be introduced by plastic deformation prior to cleavage c) They can be formed just in front of the tip of a propagating cleavage crack.' These three situations will be considered in turn. Grown-in Dislocations—It is not possible to see the individual monomolecular cleavage steps that emanate from isolated screw dislocations in crystals.

Jan 1, 1959

By Robert Mehl

RELATIVELY few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive ;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZn2, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.4 Fundamentally, methods for the determination of the state of molecu¬lar aggregation in solution depend upon the kinetic behavior of the par-ticles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecu-lar solid solution would be afforded. Freche5 examined the rates of independent and simultaneous diffusion of magnesium and silicon in

Jan 1, 1939

By Doll. H. G.

THIS paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole, By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simple and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, time-saving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given.

Jan 1, 1942

By Hsun Hu

The formation of annealing textures in high-purity silver, from the various rolling textures obtanled in the course of texture transition, was studied. It was found that from a brass-type rolling texture the recrystallization texture is mainly (120) [211] type, which is quite different from the recrystallization texture of brass. From a predominantly copper-type rolling texture, the reclystallization texture is mainly (100) [001]. The recrystallization texture of silver- varies also with the degree of purity. In each case, however, the reorientation can be expressed as [Ill] rotations of 30° to 40°, which is consistent with the oriented growth theory of the formation of annealing textures. ThE recrystallization textures of rolled silver were studied long ago by Glocker and co-workers (1924-27) and were reported to be (113) [iil] upon annealing at low temperatures.1 Since that time, no further study of the recrystallization textures of silver, particularly with the modern techniques of quantitative texture determinations, has been reported in the literature. In a previous study2y3 it was found that the rolling texture of high-purity silver (99.999 +pct pure) is changed gradually from the common silver- or brass-type to the copper-type by raising the temperature of rolling from 0" to 200°C. The formation of annealing textures from the various rolling textures in the same material is, therefore, of considerable interest. The present paper constitutes the results of such a study. MATERIAL AND METHOD Specimens were taken from the same strips of high-purity silver* that were used previously for

Jan 1, 1962

By C. G. Dunn, K. T. Aust

SEVERAL studies1-10 have reported a type of grain boundary migration which occurs when a strained grain grows into an adjacent deformed grain during annealing. Beck and Sperry called this phenomenon strain-induced grain boundary migration, since the observed boundary movement, which takes place in a direction away from the center of curvature, is apparently motivated by the excess free energy of strain hardening. However, little information has been obtained on the detailed structural changes accompanying such grain boundary motion. The problem of driving force for strain-induced boundary migration was considered by Dunn and Daniels,' who used bent bicrystals of Si-Fe. They demonstrated that two grains of differing energy, in the form of subboundaries, behaved according to the concept that the low-energy grain would grow at the expense of the high-energy grain. Beck" reported experiments of Sperry for high-purity aluminum, which indicated that generally the particular grain of a pair which work-hardened more was invaded. The measure of work hardening here was

Jan 1, 1958

By M. E. Wadsworth, K. J. Richards

The oxidation rates of tantalum in various partial pressures of carbon dioxide in the temperature range 700°to 950°C were measured with a thermo-gravimetric balance. Oxidation involved a surface -controlled reaction associated with the formation of a nonprotective layer of Ta2O5. Below about 720°C, there was a change in the rate-determining mechanism, and above 830°C the linear rate was preceded by a complex region of nonlinear oxidation behavior. The linear oxidation of tantalum has been explained quantitatively in terms of carbon dioxide adsorption, followed by a rate-controlling surface reaction. The initial adsorption has been expressed both as an equilibrium process and as a steady-state reaction. The enthalpy for chemisorption of CO, was determined to be -17.3 kcal per mole. The surface-controlled reaction had an activation enthalpy of 40.4 kcal per mole. A considerable amount of interest has been shown in recent years in the oxidation of tantalum and the nature of the oxide film produced. This interest is associated with the increasing demand in our technology for structural materials to withstand high temperatures and corrosive atmospheres. The low oxidation resistance of tantalum has severely restricted its application as a high-strength, high-temperature material. As a fundamental approach to the realization of the full poten- tials of this metal, the kinetics of the oxidation of tantalum in oxygen and air have been extensively studied; however, very little work has been reported on the effect of other gases, including carbon dioxide. According to Miller,' the only reported study of the reaction between tantalum and dry carbon dioxide is a restricted observation by O'Driscoll et al.2 at 8 atm absolute pressure and 500°C. Therefore, this study was made to investigate the reaction of tantalum with carbon dioxide. EXPERIMENTAL MATERIALS AND METHODS The vacuum-annealed tantalum used in this study was obtained from Fansteel Metallurgical Corp. as 0.025-mm-thick sheet stock. This material had less than 0.1 pct total impurities, and the maximum individual impurity concentrations were

Jan 1, 1964

By M. G. F. Söhnlein

In the earlier clays, these ores were treated by chloridizing-roasting followed by amalgamation, with satisfactory results, according to the information now available. Material from old tailing dumps from ore treated by this process, which are found at several places in the vicinity of Oruro, seldom contains more than 5 to 6 oz. of silver per ton. As ore with less than 100 oz. per ton was not treated, the extraction of silver must have been good. Reports of the operating companies published about 1890 asserted that over 90 per cent. of the silver was recovered, but in these calculations, as a rule, no allowance was made for silver lost during roasting and the figure referred only to the extraction of silvcr by amalgamation from the roasted ore.

Jan 1, 1921

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in .he discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in he smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently n the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of he joined pieces (base metal). The filler metal, older or braze, is always of lower melting point than the base metal. Consequently with these) recesses there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Joining operations carried out at temperatures above 500°C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used.

Jan 1, 1975

By K. C. Carriere

INTRODUCTION The purpose of this section is to introduce the reader to the concepts of computer control of grinding circuits, and to flag some of the opportunities to be encountered, but without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with computer hardware and software, and in particular with the grinding process. The paper is organized into four parts: a general commentary of the need for computer control of grinding, a discussion of the process considerations involved, a more detailed elaboration on the current state of applicable computer technology, and a case study indicating one approach towards such a project. A brief installation survey and references for further reading are also given. This section will primarily deal with supervisory computer applications. Direct Digital Control and microprocessor systems are generally used as replacements for analog controls and thus are not considered in depth. Many configurations of grinding circuits exist, necessitating certain assumptions. Since many new concentrators use an open circuited SAG mill feeding a closed circuit ball mill, this configuration is used as a model although the principles stated can be extrapolated to any circuit. Motivation The use of computers for industrial control has been one of the dreams of control engineers and operators alike for many years. The concept of a plant running at optimal conditions with minimal operator involvement is very attractive from economic and technical standpoints. Accomplishment of this goal has been a long struggle, but today likelihood of success of such a project is very high, considering the reliability of modern hardware and the sophistication of available software. The primary motivation of any control system must be economic, i.e. it must pay for itself and make money for the owner, directly or indirectly. In grinding control the benefits which can be expected include: a) Higher through-put b) More uniform product in particle size, density and volumetric flog: c) Reduced operating costs including media consumption, power consumption and liner wear

Jan 1, 1982

By H. W. Graham

THE young metallurgist of today who thinks casually of the technical literature of the steel industry might conclude that little has been published concerning the Bessemer process. This conclusion is true as relating to the last decade or two, but there is a fairly voluminous Bessemer literature in the period of 1860 to 1910, Since that time, however, an entirely new level of metal-lurgical knowledge of steelmaking has been reached; and the present paper is simply an effort to look broadly from this new level and to bring the recorded history of the process up to date, It is an effort to appraise the acid Bessemer method of steelmaking in the light of today's technical knowledge thereof. In this paper matters of history will be dealt with only insofar as they contribute to an understanding of today's situation. Attention will be directed to the apparent causes of past developments in seeking to perceive the true direction of trends now in existence and effective as bearing upon future developments. The paper will discuss the economics of the Bessemer process, but only to the extent that will bear upon the metallurgist's understanding of his respon-sibility. The problem of the quality of Bes-semer steel will be reviewed and examples will be given of the technical data upon which the reasoning of the paper is based, Matters of engineering design, mechanical maintenance, operation and metallurgical investigation will be surveyed. Compari-sons will be made between the Bessemer and open-hearth processes for the sake of clear and ready understanding,

Jan 1, 1940

By Andrew L. Mular, K. K. Humphreys

Introduction Estimates performed on potential future plants must by their very nature be either order-of-magnitude or budget (preliminary) estimates. Of the three types of estimates recognized by the American National Standards Institute (ANSI Standard Z94.2), order-of-magnitude and budget estimates are the least accurate. Order-of-magnitude estimates have an expected accuracy of plus 50 percent to minus 30 percent. In other words, it is anticipated that actual project cost will be no more than 50 percent above the estimate and no less than 30 percent below the estimate. Budget estimates, or preliminary estimates as they are often called, have an expected accuracy of plus 30 percent to minus 15 percent. The reason that greater accuracy cannot be expected in performing estimates on proposed new facilities is simply that insufficient data is generally available to permit performance of a highly accurate estimate. As stated in ANSI Standard Z94.2, a definitive estimate, i.e., an estimate with an expected accuracy of plus 15 percent to minus 5 percent," . . is an estimate prepared from very defined engineering data . . . (including). . .as a minimum, fairly complete plot plans and elevations, piping and instrument diagrams, one line electrical diagrams, equipment data sheets and quotations, structural sketches, soil data and sketches of major foundations, building sketches and a complete set of specifications." In other words, the engineering of the project must be fairly well underway to permit a definitive estimate to be performed. Such is the case only after the construction decision has been made, all potential alternatives evaluated, and major expenditures committed for a particular course of action. This situation is beyond the scope of this chapter. The chapter is directed to comparison of various technological alternatives for which site specific engineering data is not generally available. Accordingly, such comparisons can be made only by utilizing preliminary or order-of-magnitude estimating techniques.

Jan 1, 1982

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By Andrew B. Crichton

No more important question has come before the coal industry in the past decade than the prevention of stream pollution by mine drainage; especially in Pennsylvania, where large areas of coal land have been developed. It may be thought that the problem of labor or lack of transportation outweighs in importance that of stream pollution. We can see possible remedies for labor and transportation problems but there is no known satisfactory solution of the mine-drainage problem. The subject has been given little serious attention, for, until recently, it has been little understood; but in the past year it was brought to the attention of the coal-mining industry by the introduction, in Congress, of several bills designed to prevent the discharge of acid waters from mines or other sources into navigable streams, or their tributaries. The first legislation proposed was the Applebybill, H.R.7369, designed particularly to prevent the oil pollution of coastal waters. It contained the following provisions, which the coal men regarded as referring to the coal industry. It shall be unlawful to throw ... any refuse matter of any kind ... into any navigable waters of the United States or into any tributaries of any navigable waters from which the same shall float or be washed into such navigable waters. The chemical, steel, paper, and other manufacturing industries, as well as the mining industry, objected to this clause, the miners claiming that it would prevent the discharge of waste or mine drainage into any waters of the United States, for all streams or tributaries finally reach navigable waters. The next bill introduced was that of Congressman Briggs, H.R. 7430, an amendment to Section 13 of the Pollution Act of March 3, 1899. The original act referred chiefly to oil and oil refuse, but it provided also "that no material of any kind should be deposited on the bank of a navigable water, or tributary, which might reach the waters and interfere with or

Jan 1, 1923

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935

By Oliver C. Ralston, James E. Norman

Separation of minerals by froth flotation is rightly called an art. It can truthfully be said that no two ores separate in the same way. The difference in results obtained when natural and synthetic mixtures of minerals are separated is so great that such tests frequently have been worthless in attempting to select conditions in which a natural mixture will separate. With a few rare exceptions, the natural mixture is much more difficult to treat than a synthetic mixture, and a much poorer separation is obtained. Perhaps several experimenters have wondered why 10 or 20 per cent of a mineral being floated from an ore does not float and is different from the 90 or 80 per cent that is recovered. In experimental tests on pure sphalerite, observers' have noted that varying amounts of sphalerite may be froth-floated with pine oil alone, the amount recovered in the froth depending apparently upon the source of the sulphide. The only explanation of results such as these, barring insufficiency of frother or time of flotation, is that the surface of the mineral floated is different from that of the mineral depressed. This difference often has been found to be caused by natural contamination of mineral surfaces, apparently brought about by weathering and exposure to natural solutions. There is virtually no rock that is absolutely unweathered. One of the writers had an exceedingly instructive experience in 1931 while working with United Verde copper-zinc iron sulphide ore in Arizona. Nonselective flotation of chalcopyrite and sphalerite away from some of the pyrite was all that could be accomplished. All known depressants produced only slight effect. Sodium cyanide showed some effect, but so much had to be used that only a small amount of chalcopyrite could be

Jan 1, 1939

By C. D. Rubert, W. J. Parton

Large quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recover ing coal from the waste water of a a plant (breaker) by froth cleaning and to obtain operating data for designing a commercial plant if the results were favorable. Preliminary Investigation Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table. The refuse content increases progressively as the size of the particles decreases The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the cod. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour* was sufficient to elimi-,late much of the minus 200-mesh material while allowing the coarser material to settle and be thickened,

Jan 1, 1944

By F. Louis Grammer

The iron industry has been so markedly the cynosure of all eyes, that a sense of weariness has overtaken many on-lookers, and a new wonder is desired. While the commercial phase of the iron industry has necessarily engrossed the public attention and probably is the more worthy of record, still the mechanical and metallurgical phases have recorded conspicuous advances and merit attention. In order to appreciate the present condition of blast-furnace practice, it is necessary before enumerating the advances made during the past decade to give a brief discussion of the tendencies in the methods of administration as well as the conditions governing supremacy, for these factors have modified the aims of the manager. It might also be well to apologize for a record of the advances made during such a short period as a decade, were it not that, for the individual, time is marked as much by the impressions recorded on the brain as by the jumps of the second hand of a watch. Furthermore, this article is written in order to carry out a project of the late Dr. Egleston, to have a record made each decade. I regret that the data collected by him, and forwarded to me, end with 1896, and therefore do not include the interesting results which followed the introduction of Mesabi ores. The perusal of the notes is melancholy reading, somewhat like the feelings we experience in going through a graveyard. It is a record made up of so many plants, which have ceased to be factors in the iron world, if they are not entirely moribund. Historically, they would be interesting, emphasizing as they do the abnormal and somewhat overestimated importance of furnace lines, taken without proper reference to volume of blast and nature of stock used. I regret, however, that the time at my disposal does not permit of this presentation.

Jan 1, 1905

Mounting pressures to increase efficiency and yield, conserve energy, or minimize pollution have all taken their toll on the minerals industry. As management and technical personnel take a harder look at their operations for ways to shave cents off operating costs or to squeeze a bit more productivity out of existing equipment, instrumentation often comes up as the most effective answer. When Amax Lead installed an automatic grind control system in its Buick mill, ore throughput increased by 3 to 5%. Mill operators calculate that the initial investment is returned to them several times annually.

Jan 2, 1978

By John K. Hammes, Stanley D. Michaelson

The material presented in this chapter is supplemental information on those significant aspects of open-pit copper mining that are to an extent unique and therefore not detailed in previous sections covering the fundamentals of open-pit mine planning, operations and maintenance. In addition, tabulated cost and operating data are presented for a variety of open-pit copper mines. 13.3-1 History. The history of the civilized use of copper began at the end of the Stone Age when man discovered that the red metal, in the form of native copper, could be readily worked into a variety of weapons and tools which simplified the primitive requirements for survival. Almost concurrently, the high value of these early copper products became so widely known that they soon assumed major importance as trading commodities. Copper and copper-alloyed artifacts, even though produced in very limited quantities by ancient miners and metalworkers in a few parts of the Near East and the Western Hemisphere, were so valuable that early warriors and traders carried them into nearly all the world's known areas of importance. As far as copper is concerned, the Bronze Age, at sometime around 8000 BC to 6000 BC, marked the vague, little-known beginning of metallurgy. Man learned to alloy the valuable red metal to make it harder and tougher; its use multiplied as did the variety of weapons and tools made with the gradually increasing metallurgical and fabricating skills. By 3000 BC bronze alloy products became relatively widespread ; copper mining activities assumed tremendous importance and the mines on the Isle of Cyprus developed into prized possessions of each Mediterranean empire from the times of Egyptian supremacy to well beyond the decline of the Roman Empire.

Jan 1, 1968