Search Documents

By J. Siege1, R. S. Popielak

A computer model was used to simulate the effect of leakage through confining beds on a hypothetical in situ leach operation in an aquifer with a thin mineralized section. The simulations were used to assess economic and potential environmental implications of leakage on an in situ leach operation. Four scenarios were modeled - three representing cases with different degrees of confinement, and the fourth representing a stratified ore zone under a low degree of confinement. The model simulated the travel path and travel time of lixiviant given the hydraulic conditions prescribed in each scenario. The results show that the travel path and travel times vary by about 10% for confinement ranging from nearly impermeable (essentially no leakage) to an extremely low level (thin confinement with a permeability about equal to that of the aquifer) for isotropic aquifer conditions. The aquifer thickness contacted by the lixiviant varied from 85% to 90%. Horizontally, 55% to 60% of the aquifer was contacted. The flow paths in the stratified aquifer were reduced in the vertical direction and expanded horizontally. Forty- five percent of the aquifer thickness was contacted vertically with 88% contacted horizontally. Break- through time for lixiviant traveling at mid-depth of the aquifer increased two times when the leakage was increased from nearly zero to a value representative of thin and highly permeable confinement. Leakage affects the economics of in situ mining by (1) increasing the time required to leach out the ore, and (2) increasing the thickness of the ore zone aquifer to be restored. The potential for environmental impacts appears to be minor. In all four simulations, the lixiviant did not contact the confining strata. Restoration would be limited to cleanup of the ore zone aquifer within the thickness contacted by lixiviant and within the radius of the lixiviant that traveled farthest away from the production cell.

Jan 1, 1988

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Brian Flintoff

SCOTT COULTER: Our second speaker today is Brian Flintoff. Brian graduated from the University of Alberta in 1973 with a master's of science degree and worked as a project metallurgist at Brenda Mines until 1977. He returned to the University of Alberta in late 1977 to work on his Ph.D. and later joined the faculty of engineering in 1980, leaving in 1988 to rejoin Brenda in the newly formed process technology division. In 1998 he left Svedala-Brenda to take a position with Simons International's newly formed enterprise development services group. His topic today is "People: Reduce, Reuse, and Recycle." INTRODUCTION BRIAN FLINTOFF: Historically, the mining industry has relied on the people within a corporation to get things done. The culture of most companies was one of a slow but sure development of people, processes, equipment, and technology. Many of the larger companies supported in-house engineering and research organizations. However, the metal market pressures of the 1980s and the emergence of the global economy in the late '80s and early '90s put enormous financial pressures on the industry. As the old adage says, "necessity is the mother of invention," and the mining industry, like many others, has undergone a transformation. A cornerstone element of the transformation was the downsizing (or right-sizing) that was calculated to "trim the fat" from the capital and operating budgets. The goal was and is to find the highest sustainable operating profit.' While I'm sure one can find examples of losers (e.g., those who can be classified as suffering from corporate anorexia or institutional Alzheimer's) in such business reengineering efforts, there is little doubt that, on the whole, the transformation has been successful. The reality that now faces mill management is "How to do more with less?" At the risk of oversimplifying, one can look at this on two levels:

Jan 1, 1998

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome's Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation's second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By Scott G. Britton

In the real world of coal mining, the bottom line for almost every support project decision is economic (i.e., what is it going to cost?). Up to this point, I have discussed the methods to improve the performance of typical support projects by better installation, materials, and techniques, thus lowering the impact of the bottom line cost. In this chapter, 1 shall explore what costs are relevant in mining construction, and how these costs are developed. The chapter centers around two major discussions: (I) developing cost accounting techniques, and (2) cost-estimating procedures for support construction. Each focuses on the fundamentals of practical cost considerations necessary for decisions on construction projects underground. Since cost accounting, economics, and investment planning are all subjects which warrant complete discussions on their own, this chapter will focus on distilling the important concepts required by a planning engineer into an easily understandable presentation.

Jan 1, 1983

By Bernie W. Martin

The East Side Access (ESA) project is the largest commuter railroad project ever undertaken in the United States. The purpose of the ESA project is to bring commuters from Long Island into Grand Central Terminal. The program is estimated to cost $4.3billion. The purpose of this paper is to describe the key design elements for the Queens segment, ?re life safety, ventilation and changes to the proposed contract delivery method.

Jan 1, 2003

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil's primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri's production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri's research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By M. P. Evans, Rainer Kahrger

During the last decade or so great advances were made in the solvent extraction, electro winning technologies. They, combined with heap leaching, made it viable to exploit large, relatively low grade oxide copper deposits. The El Abra mine is a good example for such a deposit. Situated in Northern Chile at an elevation of about 4000m (14000 feet), 70 krn north of Calama, the El Abra deposit has been known for many years. In the early 1990's Codelco decided to sell a major holding in the deposit to international mining companies. After lengthy negotiations Cyprus Minerals finalized in June 1994 the purchase of 51% of the deposit with Codelco retaining the balance. lance. Already in 1993 Cyprus and the engineer on the project, began discussions with international materials handling companies with regards to the materials handling system required for the project. These early discussions were considered critical for this fast track project. Immediately after the notice to proceed with the project, several companies were invited to submit competitive conceptual proposals for that portion of the material handling system which was to transport crushed and treated ore from the plant to the leach pad and build the leaching heaps at a rate of up to 150 000 tons per day. A supplier was selected. Additional studies were made for the conveyor system from the mine to the fine crushing plant. Due to the extremely rugged terrain and high altitude at the mine, a decision was made to locate the plant and the leaching operations 15 km east of the mine at an elevation of 3400m. In July 1994 the supplier started the conceptual engineering with a design team at the engineer's San Francisco office. The undertaking was unique in the sense that the supplier's engineering team was integrated into the project for the duration of the conceptual engineering. The open and continuous communication greatly contributed to the success of the design work.

Jan 1, 1996

By Phoebe L. Hauff, Jeffrey P. Kurtz, Paul D. Chamberlin

Clay minerals can be a source of problems in heap leaching operations. The ore for many heap leach operations is commonly acid-sulfate alteration zone rocks which may be found in hot springs deposits as well as the supergene zone of other near- surface gold deposits. Clays can be important constituents of these ores. Swelling clays, such as smectite, can come loose from the agglomerated ore, migrate within the heap, concentrate in pore spaces and often plug up flow channels in the heap Cement is often added to the ore as a binder during the agglomeration process. Lime is added for pH control. Their presence, combined with the sodium cyanide commonly used to leach, can raise the pH of the leach solution to 10 or even 12. This very alkaline solution can cause dissolution of some mineral Some clays, such as kaolinite, are not very stable in high pH solutions. They can be dissolved and reprecipitated as other clay species if sufficient silica and the appropriate cations are available in solution. Silica gels and amorphous materials can also be created from the dissolved kaolinite and other minerals and act as retardants to the flow of leach solutions in the heap. Therefore, before a heap leach operation is built, the operator should evaluate the clays in the ore and test the agglomeration procedure. It is important to know not only the mineralogy and the chemistry of the leach environment but how the minerals and solutions interact and what the products of this interaction are. A hypothesis is presented in this paper that expanding smectite- bearing clays can be generated within the heap. How and why this happens will be explained.

Jan 1, 1987

By David Field, David Powell, Richard Hulsen

The Mission Valley Light Rail will loop through San Diego State University (SDSU)and to minimize the impact of construction most of the works will be underground. The project will require construction of a 330-m long (1080-ft), 11.24-m wide (36.9-ft),single twin track tunnel through Stadium Conglomerate, a poorly cemented dense sandy gravel with cobbles. Key technical issues are discussed including the ground conditions and predicted ground response, the use of sequential excavation methods to control deformations and specific construction concerns such as instrumentation and monitoring. Management of the construction process to minimize risk is particularly important in this environment and the strategy selected to control the works is also considered.

Jan 1, 2001

By H. Maleki, G. Tetreault

This study was initiated by the US Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room- and-pillar mining using a continuous miner (CM) was economically sound or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets " are left in longwall mines on one side of the mains near outcrops and adverse geological conditions or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included the analysis of the geologic, geotechnical and economic factors that influence the recovery of small coal reserves; the analysis of historic changes in supply, demand and coal prices; the development of typical cost models for room-and-pillar and longwall mines; and the development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR), as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modern longwall mines and, thus, is used to evaluate the increased costs associated with adding new development sections for extraction of small reserves. The study examines the economic feasibility of using unconventional longwalls for the recovery of medium-sized reserves, depending on site-specific geologic and geometric conditions.

Jan 1, 2002

By P. Somasundaran, F. F. Aplan

The Formative Years Douglas Winston Fuerstenau was born December 6, 1928 in Hazel, SD to Edwin Arnold and Hazel Pauline (Karterud) Fuerstenau. His father, of German extraction, was a farmer and, later, a cabinet maker, while his mother, of Norwegian lineage, was a school teacher. His parents are still alive today at ages 91 and 88, respectively. Two younger brothers, Richard and Maurice and a sister, Jean, completed the family. The family first lived near Watertown and later in Lemmon and Mobridge, SD. The 1930's were a difficult period for any family in South Dakota. A decade-long drought made this a part of the dust bowl, which together with a serious infestation of grasshoppers (the locust plague described in The Bible), and the world-wide depression, made living difficult for all. In spite of these privations, Doug has many happy memories of his childhood which can be attributed to the resilience of youth and a strong family structure. He has fond memories of summers spent with his cousins on family farms where the children were introduced to farm chores at an early age. When he was old enough, he worked in a grocery store after school. At the age of 14 he spent the summer hearding 2,000 sheep near Lemmon, SD as his contribution to the war effort in that labor-short period. He remembers well the dust storms of the 1930ts, the destruction at his grandmother's farm by tornado, pulling weeds on the farm, threshing grain with a monstrous steam-driven machine and such pleasant childhood activi- ties as fishing for bullheads, hunting for rabbits, searching for arrowheads in newly plowed fields, and ice skating in the winter. Early in life his parents instilled in him a strong work ethic, a love of learning and the need for a good education. In 1943, the family moved to Rapid City, SD. With a population of 13,000, it was

Jan 1, 1989

By Chuck R. McLendon

A new face ventilation system was needed at the Allied Chemical Trona mine, near Green River, Wyoming. The development of an exhaust manifold face ventilation system came from a need to reduce the dust and noise concentration level while maintaining methane control at the continuous miner working face. Dust laden air from a heading being driven by a continuous miner was contaminating the intake air in the mine around the roof bolter operator and adjacent headings. Each working heading was exhausted into the last open crosscut by a face fan. A face fan would contaminate the adjacent downstream heading with dust-laden air until a high dust concentration developed in the final entry before the returns. A face ventilation system was needed to give the exhaust of each heading an individual path to the return air. In addition, the system could not interfere with the present room and pillar mining process. A manifold system of rigid duct ventilation tubing was designed using the existing fans in a parallel arrangement. Each system was to consist of the rigid duct tubing in three headings junctioned together at the last open crosscut and exhausted at a common branch in the return air. Each heading was to have its own damper (or valve) so that air could be directed where it was most needed. The system was installed using both round and oval rigid duct ventilation tubing to minimize head loss and to allow proper ground clearance for mining machinery. Two fans in parallel were used to exhaust three headings. By adjusting the valves at each heading, up to 18.0 kcfm (9.36 cu m per sec) could be exhausted from one heading and still keep the methane level controlled in the other two headings. The manifold exhaust system has proven to be an efficient, long lasting ventilation system at the Alchem Mine. It has reduced the dust and noise exposure levels at the working faces while keeping the methane level under control.

Jan 1, 1980

By G. Meiers, M. O’Kane

Dry cover systems as a closure option for management and decommissioning of waste rock and tailings is a common prevention and control technique used at numerous sites around the world. Numerous site-specific factors control the long-term performance of dry cover systems. Site-specific climate conditions are one of the key factors to consider when determining the objectives of a dry cover system because these conditions will significantly influence long-term performance. There are advantages and disadvantages of characterizing the site on an annual basis as generally a “dry” site (annual potential evaporation greatly exceeds annual precipitation), or generally a “wet” site (annual precipitation meets or exceeds annual potential evaporation). The field performance monitoring data and discussion presented herein illustrates the caution that is required when using these “annual” criteria for characterizing site climate conditions. Numerous sites exist where precipitation exceeds potential evaporation on an annual basis; however, the site typically experiences hot, dry summer months where evaporation greatly exceeds rainfall. These dry summer conditions have a strong influence on long-term performance. In contrast, sites where potential evaporation exceeds precipitation on annual basis, typically experience periods of the year when a moisture surplus occurs, which also impacts on long-term performance. This paper uses soil-atmosphere cover design modelling and field performance monitoring from sites in Canada, Australia, and the United States to demonstrate the importance of considering site-specific climate conditions when predicting long-term cover system performance.

Jan 1, 2003

By Clinton Strachan, Rob Dorey

10.1 INTRODUCTION This chapter presents considerations which should be applied to heap leach pad site selection, site evaluation, and design, relative to the geotechnics of the site and ore. 10.1.1 General Guidelines are presented covering the topics encountered in design and construction of heap leach faci1ities. Because geotechnical characteristics vary from site to site, not all geotechnical topics associated with a specific heap leach facility are presented, and there may be exceptions to some of these guidelines. The general features of a heap leach facility (from Chapter 1) to be discussed in this chapter are: • Leach pad (including leach pad foundation and liner); • Heap; • Solution storage faci1ities (for pregnant and barren process solutions) ; and • Solution collection facilities (which collect and convey solutions in the heap and convey them to solution storage facilities). These general features are illustrated in Figure 10.1. Liners for these facilities are discussed in Chapter 11. Solution application systems and the sizing aspects of solution storage facilities are discussed in Chapters 6, 7, and 12. The general features listed above are constructed with and overlie naturally occurring materials (such as ore, borrow soils, and subsurface soils and rock). These natural materials are relied upon to perform in an acceptable manner as a component of the leach facility (such as the liner, drain material, and foundation).

Jan 1, 1988

By George D. Roberts

Dams are constructed to retard the flow of water or debris; therefore natural forces are constantly at work to remove such obstructions. To circumvent nature and avoid expensive trouble with a dam requires thoughtful far-sighted planning, careful construction control and vigilant periodic inspections to detect and repair deterioration at its inception. Although the factuality of the foregoing statements is apparent, all too many have failed to consider them in the past as will many in the future. "The economic, but safe construction of dams calls for the highest order of technical knowledge, practical experience and sound judgment." (1)

Jan 1, 1967

By Aldo F. Barsotti

The production and consumption of industrial minerals in the United States traditionally have played important roles in mining and in the supply of the bulk of basic raw materials to the economy. This diverse group of minerals extracted and consumed by a variety of industries accounts, on a weight and volume basis, for most mineral-based products consumed in our economy. Industrial minerals form the bulk of the basic raw-materials feedstock for most of the construction, agricultural, and inorganic-chemical-manufacturing sectors, and a good portion of the transportation, manufacturing, organic chemical, and service sectors of the U.S. economy. In this presentation, I discuss current estimates of the amount and value of industrial minerals mined compared with all mining in 1997. I then present a summary of 1997 production of industrial minerals by several end-use industries. This is followed by a historical perspective of the consumption of industrial minerals as a subset of all basic materials, with special emphasis on the aggregates industry. The presentation concludes with a look at the geographic distribution of industrial mineral operations in the United States and some thoughts about the future.

Jan 1, 1999

By Cynthia M. Walck, S. K. Grant, R. D. Hagni

The Post Gold deposit is located in the northern part of the Carlin trend. The mineralization at Post occurs in proximity to a Jurassic-Cretaceous composite stock. Most of the gold at Post is hosted by non-metamorphosed calcareous siltstone and highly altered diorite, adjacent to the low grade skarn. Endoskarn, exoskarn, hornfels and marble are developed outward from the intrusive. The skarn is composed dominantly of diopside, tightly intergrown with gannet, k -feldspar, and sphene. The highest grade gold values are adjacent to the skarn, which acted as a permeability barrier to fluid migration. Post is the first Carlin-type deposit at which a skarn has been recognized to play a significant role in the localization of gold.

Jan 1, 1990

By Frank Palkovits

All technologies move through a cycle from infancy to maturity. Thickened tailings have moved into the young adulthood phase of its development. Many mining companies like the idea of reducing their water-taking and water disposal issues. This limits the risks associated with traditional surface water-covered tailings facilities and the reduced dilution possible through underground disposal of thickened or paste tailings. Just as home theater systems advertised as ?plug and play? are rarely quite that straightforward, implementing and improving a thickened-tailings system has its challenges. However, the technology has also developed in recent years so it is more accessible. Some success factors have emerged because of the new technologies. Is thickened tailings the right solution? The first step in success with thickened tailings should be whether it is, in fact, the right solution for a particular mine. And, if so, what type of thickening is best. The answer depends on several factors, including: ? Grain size: The grain size that is optimal for maximizing mill recovery is some-times not suitable for thickening. Other mineralogical factors, such as mica content, may also influence whether the tailings are suitable. ? Water issues: Available water does not always have the purity necessary for the process. Another issue to consider is that if water is in short supply, as is increasingly often the case, thickening may be a way to reduce the need to both take and dispose of water.

Jan 1, 2008

By Fathi Habashi

METALS COMMONLY leached may come from one of the following sources: 1) Occurring in nature in the native state, e.g., gold, silver, platinum metals, copper. 2) Produced as by-product of a metallurgical process, e.g., gold, silver, platinum metals, selenium. 3) Produced by reduction of an oxide ore, e.g., copper, nickel. GOLD AND SILVER Cyanidation According to Mellor (1923) the alchemists of the eighteenth century knew that gold was soluble in aqueous solution of potassium cyanide, and the early jewelers probably utilized this fact in gilding. He also mentions that Scheele in 1783 and later Bagration in 1843 noted the solvent action of aqueous solutions of alkali cyanides on gold. Yet it was not until 1887 that the value of this observation was recognized, when MacArthur and Forrest (1887) made use of it in leaching gold from its ores. Since then, the process has spread to every gold and silver mining district in the world.

Jan 1, 1970