Search Documents

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

Over the past 12 years screening of materials has undergone a dramatic change in both the types and materials used in screen mats and the quality requirements of the finished product. With the main thrust now on quality and a cleaner product a different approach was needed in the operation of sizing screens. New screen mats with many different aperture configurations have been developed using rubber and plastics.to replace the traditional screen mat of woven wire or punched plate.

Jan 1, 1984

Welcome to Mount Isa- my home city and without doubtthe base for what promises to be the most exciting mineral development yet seen in Australia.Mr. Chairman, it also gives me great pride to representthis area in the Queensland State Parliament as well as being the Minister for Minerals and Energy in the Queensland Government.Mount Isa is now part of the Australian mining industry folklore.It is all what a good mine is all about. It is. all what a good community is all about.

Jan 1, 1993

By C Li, S Wang, L Qiao

Jinchuan nickel mine is the largest nickel mine in China. Cut-and-fill mining method with high density cementing materials is used in the mine. The original mining design divided the mining operation into two steps. The first step stopped the mining rooms and the second step stopped the pillars. Because the two-step method made big trouble for finally mining pillars and strongly limited the mining speed and production, it was successfully changed to a continuous cut-and-fill method without pillars. However, the mining operation in the mine has been down to 800 m and the mining condition is getting worse and more complicated. Through systemetical field investigations and 3D FEM analysis, it is proved that the mining method without pillars is feasible for mining deeper orebodies in Jinchuan nickel mine.

Jan 1, 2000

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management.

Jan 1, 1995

By Walters GW

A countercurrent method of metal refining using crystallization and reflux is discussed. 4n account is given of the development of this technique for the separation of silver and bismuth from lead using bench-scale studies to the present small pilot-plant unit (around one tonne per day) in the "Commonwealth Scientific and Industrial Research Organization (CSIRO)" Division of Chemical Engineering.

Jan 1, 1975

This paper explores options worthy of consideration in the management of S02 produced from the gold roasting operations at Kalgoorlie. Some of the options have relevance to other sources of SO2 in the region, eminating from nickel smelting operations. The paper considers the following options: 1. Capture of SO2 within the roaster where sulphur-containing reaction products are mixed with the calcine. 2. Processes in which the sulphur-containing products are bled separately from the stack for further treatment or for dumping as a waste. These include: Seawater-based scrubbing of SO2; Sulphuric acid manufacture as a feedstock for fertiliser production or for leaching of bauxite; its use as Caro's acid: and the production of value-added sulphur-containing reagents eg liquid S02 and sulphonic acid.

Jan 1, 1992

By M Slight, H Lacy

In recent times, with the global mining industry’s focus on sustainable development there has been a significant focus on mine closure and rehabilitation performance and reporting through the development of the International Council on Mining Metals (ICMM), the Global Reporting Initiative and the Equator Principles. In addition, financial reporting obligations under International Financial Reporting Standards and the Sarbanes Oxley Act (2002) have also led to better understanding and improvements with industry closure performance, liability management and reporting.Under these sustainable development principles and financial reporting obligations, mining companies are required to consider mine closure planning and associated cost estimates across all life cycle phases of the mine. Internal processes have been developed within mining companies to better understand their closure liabilities and obligations and likely costs and cost estimating processes are generally developed for long-term life-of-mine (asset) planning and budgeting, financial reporting for corporate balance sheet provisioning purposes, and regulator reporting for environmental bonding and financial assurances.These days mining companies need to plan for, prepare and actually mine for closure right from the start of a project. This means that their closure and rehabilitation liabilities throughout each stage of the mine life cycle phases must be understood, planned for, managed and controlled.So how is the industry performing? Understanding of closure liabilities is improving and reflected in liability cost estimations that are recognising the likely issues to be faced at closure, but there is a way to go to ensure that the industry doesn’t add to the increasing legacy liabilities being passed onto the wider community.CITATION:Slight, M and Lacy, H, 2016. Closure liabilities – where are we at?, in Proceedings Life-of-Mine 2016 Conference , pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Withington J. T

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

In order to fully understand why Amax Coal puts such extreme emphasis on the drilling and blasting programs at each of our mines, we must review the past. This paper will discuss the drilling and blasting techniques we used in the 1970s and their evolution to current practices. As time progressed, major changes influenced the surface mining of coal through new more restrictive governmental controls and local communities organising into groups with two goals in mind, one to shut down the mines and the second to try and get rich by making false and unjust damage suits against the mines. In virtually all of our midwest surface operations we have at one time or presently are facing litigation that has reached into the millions of dollars. Amax Coal has worked in co-operation with the United States Bureau of Mines in the areas of blast vibration, shot design, highwall safety, blast casting studies and many more. Today we are continuing to work with Dr David Siskind and his expert staff seeking answers to old and new problems addressing the blasting of overburden and parting seams.

Jan 1, 1995

Changes in mining technology have led to an increase in the number of underground sulfide dust explosions reported in Australian and overseas mines. Samples collected at the Elura mine consisting primarily of pyrite, pyrrhotite, arsenopyrite, sphalerite and galena, were tested in 8 litre explosion chamber. The dusts were found to be capable of producing dangerous dust explosions with maximum explosion pressures of 440 kPa and rates of pressure rise of 5200 kPa/s. The hazards of a sulfide dust explosion are associated with the pressure wave and flame front of the explosion and the toxic gases remaining after the explosion.

Jan 1, 1984

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

By Weatherhead J, Grounds J

The Nabarlek Uranium Project located in Arnhem Land in the Northern Territory of Australia was a small high-grade deposit which was the first uranium mine brought into operation following the extensive Commissioner Fox Inquiries into uranium mining during the late 1970s. The operation is almost complete and decommissioning plans have been prepared. This paper reviews all phases of the water management and tailings disposal for the project and compares results with design predictions.

Jan 1, 1988

By Redman P. G, McMahon B. K

A simple technique for evaluating the field stress ratio is presented, based on the results of extensometer or convergence tape measure- ments taken in an advancing tunnel. This tech- nique also yields a value for the rock mass modulus, provided Poisson's Ratio is assumed. The results of two case studies are presented illustrating the effectiveness of the method.

Jan 1, 1981

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

By Lumley G. I, Duffy W. J

The risk involved with incorporating new/unfamiliar technology into mines has, in the past, largely been evaluated by the supplier of the technology. The implications on safety and productivity has been accepted as part of the process of `getting up and running'.This has changed. As companies see the lost productivity and accidents actually costing significant dollars, risk assessment is becoming an important part of the implementation of new equipment. Regulatory authorities are also seeing the preventable incidents and in some cases are now requiring a risk assessment to be undertaken on new equipment at a Mine.

Jan 1, 1992

By X Li, R Chu, X Deng

The hot-dip galvanising industry is the largest consumer of zinc, with over 40 per cent of the world’s total annual production of zinc used for galvanised steel. The dross generated in the hot-dip galvanising coating process is a valuable co-product, since it contains high quantities of recyclable metal. A new method to recover the metal from the industrial galvanising dross was proposed using supergravity separation. During the hot-dip galvanising process, the presence of zinc dross has a serious impact on the surface quality of the hot-dip galvanised sheet, forming zinc dross defects. To reduce the impact of zinc dross, the zinc dross on the surface of the zinc pool needs to be manually or mechanically removed at regular intervals. However, during the dross removal process, a large amount of metal zinc is inevitably carried out, resulting in low zinc utilisation rate and high zinc loss rate. This article proposes an efficient and low-cost technology for the recycling and utilisation of hotdip galvanised dross, which uses super-gravity technology to recover hot-dip galvanised dross online. The metal in the hot-dip galvanised dross returns to the zinc pot in situ, while a small part of the dross remains in the super-gravity equipment, which can reduce the amount of zinc dross by more than 60 per cent and achieve a reduction in zinc loss from 17 per cent to less than 7 per cent.

Jun 19, 2024

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023