Search Documents

By D Ziaja, W Jaspers

A brief history of the development of pneumatic flotation cells from early in the 20th century to the present day and a comparison to conventional cells demonstrates the efficiency and simplicity of design and operation of the ænew generationÆ of pneumatic cells. Recent successful testwork on phosphate minerals in the USA and a variety of coal types in Australia confirm the utility and efficiency of the design. The key aspects of this technology are improved recovery and selectivity with lower capital expenditure and operating costs.

Jan 1, 2005

It is a well known fact that the best method of rock reinforcement is to avoid physical ground support. This goal can be achieved by means of: - Increasing the rock structural strength - Geological definition and forecasting. - Sequencing the excavation - Smooth blasting In many cases however, extra ground support is needed in order to maintain safe working conditions. In an open pit, the structural strength of rock cannot be increased by lowering the pit walls due to economical reasons. Economy demands steeper walls and less waste to be hauled to the dump. The geological conditions can also often be extremely poor and unpredictable. For excavation sequencing and smooth blasting there are good possi- bilities, such as cleaning of the pit walls after the main excavation, arul- ing of long small diameter straight inclined holes, use of smooth blasting techniques and lightened explosives.

Jan 1, 1989

Recent operating experience from West Australian open pit gold mines has shown that geotechnical input into initial design is rare. As a result, ground stability is poor - almost half the pits designed in this way suffer major failure.West Australian experience shows that geotechnical studies for individual mines are site specific, and therefore empirical experience cannot be transported from site to site. Geotechnical studies performed prior to design have resulted in significantly improved pit stability.

Jan 1, 1990

The Hartley layered mafic igneous complex within the Great Dyke of Zimbabwe contains economically-recoverable quantities of platinum group metals and gold, nickel, copper and cobalt. The recoverable metals are concentrated in a thin gently-dipping stratigraphic unit - the Main Sulphide Zone. The Hartley Platinum mine, jointly owned by BHP and Delta Gold NL, is scheduled to come on stream at the end of 1996 at an initial mining rate of 2.16 million tonnes per annum and will produce approximately 150 000 oz of platinum and 3300 tonnes per annum of nickel, as well as saleable amounts of palladium (110 000 oz), rhodium (11 500 oz) and copper (2232 tonnes).

Jan 1, 1996

By Houlihan RN, Landau J

A reciprocating plate column is described in which two sets of perforated plates are mounted alternately on two shafts and are reciprocated with a phase difference of 1800 between them. It is shown that such a column is mechanically superior to the previously proposed types: under practical operating conditions the pressure fluctuations at the base of the column are only a small fraction of the static head. Furthermore, mass transfer experiments with the system tributyl phosphate in kerosene- acid aqueous solutions of uranyl nitrate show that both high specific throughputs and reason- ably good efficiencies can be attained in this type of column. A comparison with the more conventional extraction equipment (mixer -settlers, pulsed columns) on the basis of residence time per equilibrium stage indicates the potential of reciprocating plate columns in hydrometallurg- ical application, especially in which the requirements of separation efficiency are modest while the scale of operation is large.

Jan 1, 1975

By Bensley C. N

In June 1995, BHP announced that it would build a Hot Briquetted Iron (HBI) plant and associated beneficiation, materials handling and infrastructure facilities at Port Hedland, Western Australia. This plant, the first direct reduction plant in Australia, will convert beneficiated iron ore fines into metallic iron for briquetting into HBI. The reduction plant will be based on the FINMET fluid bed technology jointly developed by Fior de Venezuela and Voest-Alpine Industrienlagenbau. Electric Arc Furnace steelmakers in the Asia Pacific region will be the principal customers for the product. This paper presents an overview of the facilities to be constructed by the project as well as discussing some particular technology and design engineering issues associated with the project.

Jan 1, 1996

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

By Hall C. E, Chrisholm J. M

Resource calculations for shear hosted deposits of any type are difficult regardless of which calculation technique is used. One of the main problems is the determination of the geometry of the mineralisation. Once this has been elucidated then the appropriate resource calculation methodology can be employed with a search distance and orientation that is relevant.

Jan 1, 1993

The traditional concept of optimum drill and blast is that it is achieved when ore is produced at the lowest unit cost and, because of the complexities of most mining operations, represents a band which extends either side of an overall cost m

Jan 1, 1998

Many metallurgical beneficiation and primary concentrating processes rely upon discrimination of products from gangue based on particulate density of the different minerals and combinations of minerals in an ore. The basic definition of density is simple, but the apparent density that minerals exhibit when in the environment of commercial densimetric separation processes is more complex and is ill-defined. Measurement of the apparent density displayed by minerals in their separation situation is essential if modelling of plant performance is to be meaningful or when comparison of an existing operation with a æperfectÆ separation constitutes a part of an audit or of a plant control function. Seven methods of dividing ore samples into discreet density fractions are examined and criticised in this paper. The shortcomings, difficulties and potential errors arising from the use of each method are evaluated. Most of the techniques described have been used by the author and generally their faults are understood and the resultant first-hand experience has been used to overcome these faults. A simple new computer-assisted technique for developing meaningful densimetric data is described.

Jan 1, 2004

This paper reviews the geochemistry of weathered nickeliferous sulphidic and lateritic profiles, the supergene behaviour of nickel and ore-associated elements, and their implications for exploration in an attempt to distinguish between barren and mineralised nickeliferous profiles. Nickel is an abundant accessory element in ultramafic rocks with background concentrations in some units up to 0.25 weight per cent. Ore-grades in fresh rock are mostly associated with massive and disseminated sulphide zones within magnesium-rich layered ultramafic sequences. In lateritic weathered terrain, nickel is also concentrated in the regolith profile. This process not only upgrades nickel in the gossanous weathered product of sulphidic deposits, but for sub-economic sulphide zones and some ultramafic rocks, is sufficient to result in a supergene resource. Ore-grade accumulations of nickel in regolith after sulphide-poor ultramafic rocks are referred to as lateritic deposits. Nickel sulphide zones and their ferruginous weathering products are collectively referred to as sulphidic deposits and are the major source of nickel in Western Australia. Mineral exploration in the Yilgam Block is hampered by deep lateritic weathered profiles (eg Butt and Sheppy, 1975; Smith, 1977; 1982). During the nickel boom of 1967 - 1972, most discoveries resulted from the location of outcropping nickeliferous gossan and ironstone. Exposed ultramafic terrain with nickel sulphide potential were explored intensively, mostly by gossan and soil sampling. However, up to 85 per cent of the area of the Yilgarn Block is buried by transported regolith. In these covered areas, barren and mineralised rock responses at the surface are similar and soil sampling produced unreliable results due to many false anomalies. A statistical, multi-element approach to regional geochemical exploration has evolved. Potential trace element indicators investigated, include Co, Cr, Cu, Ir, Mn, Pb, Pd, Pt, Sc, Se, and Zn. In recent years, trace element ratios have also been tested with varying degrees of Success.

Jan 1, 1996

By Segnit R. E

Two suites of dusts (waste-heat boiler and electrostatic precipitator) collected in 1976 and 1980 from the Kalgoorlie nickel smelter were subjected to chemical and XRD analysis and were examined by SEM and optical microscopy. The spherical to sub-spherical particles contained oxide and glassy phases with small amounts of sulfide. XRD showed that the major phase was a mixed Ni-Fe oxide spinel with some hematite. These phases compared well with those predicted by thermodynamics. The particle size distributions showed that in the 1976 and 1980 suites 20 per cent by weight was respectively coarser than 60 and 115/lm (boiler dusts) and 40 and 30/lm (precipitator dusts). Maximum particle sizes estimated from sedimentation chamber theory were found to be in reasonable agreement with the maximum sizes found in the dusts.

Jan 1, 1984

Leichhardt Colliery is developed for underground mining of coal seams at depths exceeding 280 m. Investigations of the area were conducted in phases, each designed to delineate seam characteristics more accurately and to indicate with increasing precision the nature of local geological features and the ranges of those coal properties susceptible to variation. The investigational campaign is described phase by phase summarizing evaluation of the area at the conclusion of each phase. Predictions of geological conditions likely to influence engineering planning are contrasted with actual conditions observed during trial mining.

Jan 1, 1974

By Mercer JK

This paper gives a description of the research undertaken by an explosives manufacturer to give better technical advice to the Mineral Industry. Blasting Physics is defined as giving a systematic and coherent account of the initiation and subsequent effects of high explosives upon the surrounding medium. As a result of this work a mathematical model based on the gener- ally accepted mechanism of blasting has been developed. The mechanism and the resulting model are briefly outlined. IFrom'this model the effects of burden, spacing, blasthole diameter, rock and explosive properties upon fragmentation and heave can be calculated. Using these calculations it is then possible to see how variations in frag Imentation and heave can affect the overall production costs of a mine whether it is surface or underground. The overall costs are made up of a number of individual costs - drilling, blasting, loading, hauling and crushing. ach of these operations influences or is influenced by fragmentation and heave s these costs are inter-related, the

Jan 1, 1975

It is not often that mines have as much warning of the approach of bad ground conditions as was the case at the Western Mining Corporation, Kambalda Nickel Operations Lafranchi/Schmitz Decline. Most aspects of this operation are in fact quite unique and like the best solutions, the answer to the problem of weak and foliated ground conditions was relatively simple; requiring the use of readily available explosives although the idea of using it in this manner may not be the most obvious.The use of high shock energy POWERGEL 2131 cartridges proved to be the correct answer, in conjunction with small changes in drill pattern design. The resulting lack of overbreak bears testimony to the success of the concept and the commitment of the miners to achieving a safe working environment.

Jan 1, 1992

By Whitford DJ

A distinct zonation occurs in the nature of submarine volcanic activity associated with westwards propagation of the Woodlark spreading system into continental crust. Olivine tholeiites (Type I MORB) flooring one spreading segment in the Eastern Sector of the Western Woodlark Basin are accompanied by more evolved "ferrobasalts". Basaltic andesites and Mg-poor andesite-dacites occur on axial and flanking seamounts respectively. In the Western Sector, Mg- and K-rich olivine andesites occur in a rift valley and on an axial seamount near the tip of the propMr/8 tig rift. Observed correlations between 6Sr ratios (0.7028-0.7041), REE patterns and K contents imply a complex petro- genesis with the relative importance of mantle heterogeneity and crustal contamination difficult to resolve.

Jan 1, 1987

By Kyle J. H, Misra V. N

The recovery of copper from a flotation concentrate using ferric chloride leaching has been investigated. The concentrate from the Horseshoe Lights Mine near Meekatharra, Western Australia, contained mainly digenite, pyrite and talc minerals. Over 95 per cent of the copper was dissolved in an acidified ferric chloride solution in one hour at 70¦C and ambient pressure. The pyrite and gangue minerals did not react. The leaching process was found to consist of four separate reactions and the shrinking core model was used to describe the process. The effects of particle size, temperature, concentration of FeCls, stirring speed and leaching time on metal dissolution were investigated. The apparent activation energies in the second, third and fourth reactions of leaching of copper concentrate were 28.8, 11.9 and 53.9 kJ/mol, respectively. The optimum conditions for the leaching of copper from the concentrate, within the range of conditions studied were: particle size 63 per cent minus 38 ¦m, a ferric chloride concentration of 1.48 M, a temperature of 70¦C, and a stirring speed of 800 rpm.

Jan 1, 1991

During the past five years there has been a transformation in the operating costs which apply to narrow vein mining. Mechanised methods including sublevel uphole retreat and narrow vein cut and fill are now proven. Other methods, such as vein mining by horizontal drilling from a raise platform are currently being tried in Australia.The important factors which affect the cost and appropriateness of each method include: ore continuity, the planarity of the wall contacts, relative hardness of ore and wall rocks and the dip bf the deposit.Drawing on current operating costs from a number of mines and on recent feasibility studies, a methodology for estimating the costs of narrow vein mining is presented. These costs are then placed in their economic context with regard to ore grade and mining rate.

Jan 1, 1993

By Payne AR

The high cost of gateroad repairs and maintenance in U.K. longwall coalmining is a clear indication of the failure of permanent support systems to fulfill their prime function, i.e. control of strata movement. The main component of gateroad support is the pack, the design and materials of which have experienced an important development process during the last 10-15 years. More recently, research investigators have attempted to give a design basis to pack quality and dimension, and reference is made to two theoretical approaches. In the course of a current research programme based upon in situ monitoring, interim design recommendations have been proposed as a means of effecting improvement in support efficiency. Identification of characteristic deformation behaviour forms the basis of the recommendations made and the subsequent improvement in gateroad performance reported.

Jan 1, 1986

By McBride N

Location The Boddington Gold Mine (BGM) is located approximately 120 km south east of Perth, Western Australia. (Figure 1). Located within the picturesque Darling Ranges, the land was previously used for forestry activities prior to mining commencing in mid-1987. Mineralisation is hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt.

Jan 1, 1995