Search Documents

By M. R. Henzinger, G. Lenz, A. Gaich, Pötsch, W. Schubert, P. Wagner

"The better the information on the rock mass and its fracture system, the better is the basis for any rock mechanical decision that is required during the excavation process. While in conventional tunnelling free view to the tunnel face is available, possibilities are limited for mechanised tunnelling using a tunnel boring machine (TBM). An approach, already formulated in 2005, is used that produces digital photographs through openings in the cutting wheel of a TBM and merges them into a circular three-dimensional image. The 3D image is then used for geometric rock mass characterisation purposes including geological mapping, for example to measure spatial orientations or determine joint spacing. In the paper the basic concept is described together with first results from a pilot test.INTRODUCTIONA three-dimensional image unites digital photographs with spatial information on the objects/surfaces it shows. Since they combine geometric and visual information they are a straightforward source for geometric rock mass analysis and geological mapping. Their obvious benefits among others are: (i) they allow spatial measurements even in inaccessible regions, (ii) they provide objective and reproducible records of the rock mass conditions, and (iii) they increase working safety (Gaich et al. 2004).Pre-requisite for the generation of 3D images is the acquisition of at least two photographs from the region of interest. From the photographs the imaged object surfaces are reconstructed by means of image analysis using methods from photogrammetry (Slama, 1980) and computer vision (Hartley & Zisserman, 2001). See also Figure 1."

Jan 1, 2015

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By Enrique Rubio

Several mining operations are currently evaluating the feasibility of changing their mining method to Block Caving. There will also be several deep low-grade ore bodies that will face the need to go underground in following their ore to depth. There are two main reasons why Block Caving is attractive: firstly, it offers the lowest operating costs amongst all the mining methods; and secondly, it is truly a massive mining method, offering the highest potential production capacity. Despite its longstanding popularity, there are still significant components of the method that are not clearly understood. Also, the lack of availability of key geomechanic information still presents a major obstacle to developing mine planning and production scheduling. There are several key issues in block caving that can make it feasible such as cavability, fragmentation, stresses will condition the way that a block caves and the way that material is drawn from the draw points. Consequently Block Cave mining method is a good example where the ore body has to be related to design and mine planning. The concepts of dilution, draw control as well as sequence definition are reviewed in this paper to illustrate the idea of integration. There have been some examples of mines where some of the components of mine planning have not been integrated causing a disaster in terms of economics or safety. Different layouts configurations might give a different result in the planning of the mine

May 1, 2002

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

"One of the workhorses of the minerals industry is the autogenous grinding (AG) mill and its derivative the semi-autogenous (SAG) mill. These are relatively well understood, but not so Scrubbers. Scrubbers are mechanically of the same appearance/function, so what is the difference between an AG mill and a scrubber? When, or under what conditions should a scrubber be used and when should an AG mill be used? Can the processes within be mathematically modelled?In the past decades, the minerals industry has focused most of its attention on the modelling of unit processes such as cone crushers, HPGR’s, AG/SAG mills and ball mills within conventional processing circuits. Less attention has been placed on the modelling of scrubbers. This paper reviews the difference between scrubber and AG mill modelling, highlighting some of the similarities, with a view to confident comminution circuit designs.Engineering practitioners should be comfortable with these circuit designs and not shy away from considering AG mills for both small and large scale plants. AG mills can treat both harder or softer ore and scrubbers are for only softer ores. This paper differentiates scrubber and AG mill modelling in a similar way that overflow ball mills and grate discharge ball mills are analysed. Smaller scrubbers (600 kW) are suited to small scale soft ore (100-300 t/h) operations. Larger scrubbers up to 2,500 kW have the capability of very high throughput, in excess of 1,750 t/h with soft fine feed ore. AG mills are scalable up to 28 MW and are capable of treating harder ores at rates exceeding 2,000 to 4,500 t/h. Observations are that the specific energy requirements for the mill grinding duty is wide and varied. This is to a large degree the crux of the matter in sizing, as well as, differentiating, scrubbers from AG mills.INTRODUCTIONAG milling is a mature technology that has been used in minerals processing applications for more than 100 years. In the last 50 years, harder metalliferous ores have seen the introduction of steel balls to assist in the grinding/milling action. Tumbling mills used in such a configuration are called semiautogenous mills (SAG). The greater minerals industry is no newcomer to the use of fully autogenous (AG) mills. Perhaps scrubbers are. What is the difference? When should a scrubber be used versus an AG mill? How are they mathematically modelled?"

Jan 1, 2016

By S. Yannacopoulos, L. Bichler, P. Wanjara, J. Gholipour

Characterization of a virgin and in-service Inconel 718 alloy was undertaken to study the changes caused by the service conditions on the grain size, ?? phase, MN-type nitrides and MC-type carbides. The size, distribution and volume fraction of these phases and grain size were studied using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) analyses. A considerable difference in the grain size, as well as distribution and volume fraction of the precipitates was observed in the in-service material as compared to the virgin Inconel 718. As a result of these microstructural changes, a notable dissimilarity in hardness between the materials investigated was observed. The results presented in this study are important for proper development of repair parameters and heat treatment of in-service Inconel 718 material.

Jan 1, 2014

By Yoginder P. Chugh

Beginning in 2010, a scientifically-founded water spray system for continuous miners (CMs) has been in development at Southern Illinois University that significantly reduces respirable dust exposure for workers in the face area (patent pending). It includes engineered sprays around the cutting drum, outer bitring sprays, chassis sprays and side cutter boom sprays. About 3.6?4.5 m behind these sprays are additional sprays that cover the area between the CM chassis and the mine roof and ribs. The innovative spray system uses approximately the same volume of water as spray systems currently used on CMs and with similar operating pressures. The innovative spray system design also takes into consideration coal dust wettability. An Illinois mine decided to implement these concepts on a CM during the rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric dust sampling and real-time monitoring with multiple personal dust monitors. The average results based on gravimetric sampling of about 105 cuts show about 30 and 20% reduction in dust exposure for the miner operator and the haulage unit operator, respectively. Visibility in the mining areas was also significantly improved. Since the initial demonstration, the coal company has implemented the system on all of their operating CMs.

Aug 1, 2013

By Ji Wang

Reflective in-seam wave detection has the advantages of a far detection range and wide applicability. It has been successfully used in detection of many abnormal geological structures in work-faces, such as faults and collapse columns. However, a reflective in-seam wave is a dispersion wave. It has weak energy and is always covered by the direct in-seam wave. In the past, underground seismic explorations were not able to image the opposite roadway using reflective in-seam waves. To solve this problem, we propose a new method of reflective in-seam wave imaging based on adaptive dispersion filtering. This method processes the reflective in-seam wave using a filter with the parameter of transmission distance. The degree of similarity of the filtered and the explosion signal is used to estimate the transmission distance and image the reflective objects. We test and verify this method using real underground seismic data. This research is helpful for the detection of coal mine goafs and abandoned roadways in work-faces or in front of tunneling ends.

Aug 1, 2013

By Patrick J. Williams

Defining Features of IOCGs ? Sulphur-poor Cu-Au(-Fe) deposits ? Contain low-Ti iron oxides ? Hydrothermal origin (breccia, vein, replacement) ? Local structural controls (no ?causitive? intrusions) Common Features (Economically-Significant Terranes) ? Regional space-time association with plutons ? Association with widely metasomatized crust ? Na ? Na-Ca ? K ? Variable enrichment in F, Co, Ba, LREE, U ? Little hydrothermal quartz (cf. porphyry deposits)

May 1, 2006

By J. Yue

The particle breakage kinetics, product size and size distribution, as well as grinding limit for quartz suspensions in a horizontal stirred mill are investigated. Results of grinding studies on quartz suspensions in a horizontal stirred mill confirm "first-order" particle breakage rates. A comparison of equation fits reveal that the product size distribution from stirred mill is best represented by the Rosin-Rammler equation when compared to the Gaudin-Shuhmann equation, but results fit poorly as particle size below five microns. A method of determining breakage rates versus particle size is demonstrated which shows that the 10% top size fraction is most appropriate for the determination of specific breakage rates. The method is used to demonstrate the relationship between particle breakage rate and particle size. As the feed particle size becomes smaller, the size reduction ratio decreases and approaches a grinding limit which depends on the effective stresses created in the mill.

May 1, 2004

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By G. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment. The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate. The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By C. M. Trigg

"PEC uranium deposit, 100 km southwest of Coppermine, was discovered by diamond drilling in 1976 following ground and airborne geophysical surveys, geological mapping, geochemical surveys and boulder prospecting that were initiated as the result of the discovery of uraniferous sandstone outcrops in 1969 by geologists of Aquitaine Company of Canada Ltd.The deposit is within gently northeasterly dipping medium to coarse-grained Unit 11 quartzitic sandstone of Neohelikian Dismal Lakes Group. The deposit is from 10 m to 70 m above the base of the sandstone which, beneath the deposit, non-conformably overlies weathered and altered Aphebian granite of Great Bear Batholith or unconformably overlies rubble breccia, conglomerate and medium-grained Unit 8 sandstone of Paleohelikian Hornby Bay Group.A northeasterly trending, 500 m wide graben, bounded by the steeply dipping northeasterly striking Imperial and Aquitaine faults, contains the deposit which is 1.1 km long by up to 340 m wide. The deposit overlies a post-Hornby Bay Group, pre-Dismal Lakes Group topographic high. Uranium principally occurs as stratabound, often peneconcordant bands; a lesser amount of uranium is fracture controlled.Stratabound uranium exists in gently easterly dipping, subparallel bands ranging in thickness from 1.5 m to 6.0 m. Pitchblende, coffinite and sooty black uranium oxides occur as interstitial disseminations and grain coatings subparallel to bedding; they also replace pyrite and form narrow veinlets.Small amounts of torbernite, carnotite and cuprosklodowskite coat pitchblende and are disseminated within mineralized bands. Pyrite, marcasite, chalcopyrite, chalcocite, cove/lite, digenite, azurite, malachite, arsenopyrite, glaucodot, niccolite, bravoite (? ), goethite, hematite and magnetite as well as quartz, barite, calcite, biotite, chlorite and clay minerals exist within the mineralized bands. Uranium grades of 0.1 % to 0.3 % U3O8 over thicknesses of 1 m to 2 m are typical.A steeply dipping fracture zone near the Imperial fault contains sooty black uranium oxides, torbernite, carnotite and cuprosklowdowskite as well as sulphides, cobalt arsenides, quartz and carbonate. The zone may reach 70 m long; its true width is about 1.9 m. Uranium grades range up to 5.18% up, over0.9m.Pitchblende and coffinite from PEC deposit have been dated at 1.08 ± .10 Ga with possible remobilization at .45 Ga. The deposit contains an inferred 3,150 tonnes of U3O8."

Jan 1, 1986

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By G. J. Hutchins

Precision surface mining is gaining traction in the iron ore, copper, iodine, limestone, bauxite, coal and gypsum markets. In this paper, we first address the possible improvements of a surface miner control using GPS techniques. An application in an iron ore mine in Western Australia is presented. The second item addressed is improvements of a new drum driving technique for a 100 ton surface miner. This technique involves installing a slow speed hydrostatic motor directly on the cutting drum rather than driving the drum through chain and sprockets. Details of the performance of this direct-drive versus the chain-drive are detailed. In addition to the 100 ton machine, we also present a 200 ton surface miner. This larger machine has 1600 hp (894.8 kg), and has been successfully introduced into a large iron ore mine in Western Australia. Performance of the 200 ton surface mining machine in various rock hardnesses is detailed. Some comments on the cost effectiveness of using a built-in loader versus loading with wheel loaders are included.

Aug 1, 2013

By Patrick R. Taylor, T. A. R. Putra

A review of various methods to treat high arsenic copper concentrates through pyrometallurgical processing is presented. Examples are drawn from various past and current operations and research. Various aspects of the engineering alternatives for treatment methods are discussed. Some of the methods discussed include: controlled oxidation roasting, adaptation of some smelter technology to accept higher amounts of arsenic, complete oxidation with arsenic fixation; sulfation roasting; acid baking, soda ash roasting, and others methods. Other topics include: a short discussion of other problematic impurities; the effects of arsenic on copper electro-refining and product purity; and methods for the ultimate disposal, or marketing, of the arsenic. The latest work being done at the Colorado School of Mines on soda ash roasting is also presented.

Jan 1, 2014

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"The McClean uranium deposits are in northern Saskatchewan, 11 km west-northwest of the Rabbit Lake mine. Their average grade is 1.8% UJ0 8 and they contain 6,350 tonnes of uranium oxide in seven pods of variable grade and mineral assemblage. They are hosted by both basal Athabasca Group and the regolith developed on the underlying crystalline basement. The major mineral facies are: sulphide, arsenide, 'bleached', and hematite, with the important uranium minerals being coffinite, uraninite and pitchblende.Abundances of carbon and sulphur isotopes are consistent with their derivation from pyritic graphite in basement gneisses. Isotopes of oxygen and hydrogen suggest mineralizing fluids were aqueous and at temperatures of about 200°C. Ar39/ Ar40 laser age determination of illite indicates mineralization began about 1300 m.y, ago and that significant hydrothermal alteration ceased about 1170 m.y. ago though Pb/U data suggest the deposits continued to evolve into the Mesozoic.The deposits are interpreted as the result of oxidizing ground water stripping uranium and other metals from either the Athabasca sandstone, especially the heavy mineral layers, or from the regolith, and precipitating these when encountering a warm reduced fluid emanating from the basement."

Jan 1, 1984

By Naizhong Xu

During the past 30 years, fully mechanized caving mining has played a positive role in the improvement of the efficiency of coal production, but which has also had a great influence on the mining environment, especially to environment damage of shallow mining areas in the central and western regions of China. The surface subsidence parameters are the basis of the surface environment evaluation and governance. During 1980~1990s of the last century in China, fully mechanized mining subsidence laws were researched more fully, however, since coal caving technology is affected by many factors, and researches on its mining subsidence laws (parameters) were found to be grossly inadequate. Through actually observed in recent years, it is considered that coal caving mining subsidence laws (parameters) can use fully mechanized mining law (parameters) for reference. Based on fully mechanized mining laws (parameters), this paper reveals the similarities and differences of the surface subsidence laws between fully mechanized caving mining and fully mechanized coal mining, which can guide the work of coal mining under buildings, water bodies and railways in new mine area and mine collapse governance.

Aug 1, 2013

By Zhibao Li, Lanmu Zeng

The behavior of dicalcium silicate in NaOH-NaAl(OH)4-Na2CO3 solution is of significance for controlling the silica level in the production of alumina via the sintering process. Dicalcium silicate samples were obtained through a twostep approach: coprecipitation of calcium and silicate from CaCl2-Na2SiO3-NaOH solutions; and calcination of the hydrated precursor at 1200°C for 4 hours. The optimization of the synthesis parameters including temperature, solution concentrations and aging time was also investigated. Xray diffraction (XRD) and chemical analysis show that the calcined solids include dicalcium silicate with trace amounts of wollastonite. The solubility of the synthesized dicalcium silicate in HCl, NaOH, mixed NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was determined. It was found that the solubility increases with increasing HCl and NaOH concentration. The effect of temperature on the solubility in HCl solutions is limited, but the solubility decreases with increasing temperature in NaOH solutions. The solubility of dicalcium silicate in NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was shown to increase with increased temperature, Al(OH)3 and Na2CO3 concentration. The BromleyZemaitis model for the aqueous electrolyte system was selected to predict the solubility of dicalcium silicate. The model’s predictions yielded certain success compared with experimental solubility data.

Jan 1, 2014

By Robert White

?Introduction of BMS?Paste fill generalities?Development through paste?Development through rock fill?Conclusion ?Brunswick mine is operated by Xstrata. The mine has been in operation since 1964 and produces around 10 000 tons per day of ore containing (in order) zinc, lead and silver? The ore body consists of close to ten sub-parallel massive sulfide lenses. The length of the ore body is 1200 m with a width of up to 200 m. From the surface, the ore body extends to a depth to 1200m ?There is 100 km of active drifts for a total 400 km ?The mine is divided by 7 levels and 23 actives sub levels

Feb 1, 2008