Search Documents

By E. G. Davis, H. P. LeVan, L. S. Smith

Leaching of a Georgia umber ore when using both ferrous sulfate and pickle liquor was studied in the laboratory . The ferrous sulfate content of the leach solution was the major factor affecting the extraction of manganese from the ore . Time , temperature , and the sulfuric acid content of the leach solutions had relatively little effect on leaching of manganese from the ore ; however , these factors did affect the amount of iron extracted from the umber and/or precipitated from solution . Simulated countercurrent leaching of the ore with pickle liquor containing 130 gpl (grams per liter ) ferrous sulfate ( 48 gpl ferrous iron ) produced a pregnant solution having 16 gpl manganese and 41 gpl iron . Filtration tests of the leach slurries indicated that separating the leach solution and solids by vacuum filtration was impractical , whereas pressure filtration was feasible when the cake thickness was limited to about three- fourths of an inch . Fired pellets of the filter cake yielded a firm , hard product analyzing 56 percent iron and less than 0.1 percent sulfur .

Jan 1, 1964

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

By L. M. Demers, D. C. Kuhn, N. El-Ayouby, C. F. Stanley

"Oxygenated metabolites of arachidonic acid (MJ are produced by the alveolar macrophage (AM) and have been shown to mediate inflammatory reactions. We therefore assessed the production of eicosanoids by AM harvested from the lungs of rats ex· posed to a bituminous coal dust for 2 wk in an inhalation chamber in order to determine if AA metabolism was altered in a manner that may promote an inflammatory response in the lung. Exposure to coal dust resulted in a 66% increase in the number of AM harvested, an increase in thromboxane A2 (TxA;i) and leukotriene 84 (LTB,j) production to 222% and 181% of control values, respectively, and a decrease in prostaglandin E2 (PGE:i) production to '62% of control values. In AM harvested from rats allowed to breath clean air for 2 wk following coal dust exposure, PGE2 production returned to control levels but TxA2 and LTB4 production remained elevated. The TxA2 synthesis inhibitor UK 38,485 reduced TxA2 production in dust-exposed AM both immediately and 2 wk following exposure. Thus, exposure of rats to coal dust significantly alters the metabolism of AA in AM, with potentially important aspects of AA metabolism remaining altered even after a 2-wk recovery period. Based on the established role of eicosanoids in inflammatory and fibrotic processes, these results suggest that the alteration of AM eicosanoid production as a result of the inhalation of coal mine dust may be an important factor in the pathophysiology of coal workers' pneumoconiosis.The authors are grateful to Joan Greenwood and Barbara Scheetz for their excellent technical assistance and to Brenda Pavone for the preparation of the manuscript. This research was supported by the U.S. Department of The Interior's Mineral Institute Program administered through the Generic Mineral Technology Center for Respirable Dust under grant 1135142.Request for reprints should be sent to Douglas C. Kuhn, Ph.D., Department of Pathology, The M.S. Hershey Medical Center, Hershey, PA 17033.INTRODUCTIONPulmonary alveolar macrophages (AM) are activated by foreign particles and microorganisms that enter the small airways (Kass et al., 1966; Herscowitz, 1985). This defensive reaction involves phagocytosis, lysosomal enzyme release, and the generation of reactive oxygen species by the AM (Snella, 1986; Rich et al., 1987). A number of agents, including phorbol esters, zymosan, adenosine diphosphate, organic hydroperoxides, and calcium ionophore, have been shown to activate the AM in vitro (Badger, 1986; Marshall and Lands, 1986; Snella, 1986). The AM response to these activators appears to be mediated in part by the oxygenated metabolites of arachidonic acid (AA) (Bertram et al., 1988; Demers et al., 1987; Mcleish et al., 1987).The AM may metabolize AA through cyclooxygenase- and lipoxygenase- catalyzed pathways to produce a variety of eicosanoids including prostaglandin (PG) E2, thromboxane (Tx) A2, leukotriene (LT) B4, LTC4, LTD4, and several hydroxyeicosatetraenoic acid derivatives (HETEs) (Willis, 1970; Camp et al., 1983; Poubelle et al., 1986). The production of these eicosanoids may enhance the. defensive ability of the challenged lung since they stimulate chemotactic cell recruitment to the site of invasion, enhance extravasation of circulating immune cells, and promote local vasodilatation. However, continued stimulation of the AM population, with the consequent production of proinflammatory eicosanoids, may ultimately enhance the disease process by contributing to chronic bronchoconstriction, fibrosis, and the persistent release of toxic oxygen species."

Jan 1, 1990

By R. L. Thorne

The Snettisham Peninsula, 30 miles southeast of Juneau, Alaska, was studied by the Bureau of Hines to obtain basic information about the size, grade, and metallurgical characteristics of a large basic intrusive containing titaniferous magnetite. The investigation, which was part of a continuing program to determine the potential reserves of iron and titanium ores in Alaska, included transit and magnetometer surveys, followed by diamond core drilling and metallurgical testing. The magnetic attraction of a part of the Snettisharn Peninsula is noted on early navigational charts prepared by the Coast and Geodetic Survey. Reconnaissance examinations by the Geological Survey and a preliminary dip needle survey by the Territorial Department of Mines indicated the general nature of the basic intrusive, but little was known as to the grade and extent of the magnetite mineralization. The detailed survey by the Bureau of Mines proved an area of approximately 390 acres in which generally high magnetic anomalies with exceptionally high localized anomalies occur. Subsequent drilling across B representative section of the deposit yielded core samples, which assayed from 11 percent to over 45 percent total iron. A large sample of core composited to represent the drilled portion of the de-posit assayed 18.9 percent Fe, 2.6 percent Ti02, and 0.29 percent S, 0.32 percent P, and 0.05 percent v.

Jan 1, 1956

By Charles L. Kimbell

The final 26 tables of this chapter, tables 14-39, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-88 editions. In this year's edition, for the first time, a column has been added to each of these tables providing a 5 year average for 1985-89, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continues to be, as in past years, in descending order of rank in the year of review, 1989. With the inclusion of silver and uranium oxide in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 in terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral of world crude mineral production in 1983. In addition, world output of five key down-stream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil are included because of their significance as products.

Jan 1, 1992

By Christopher Mark, Robert J. Tuchman

This proceedings volume contains papers presented at technology transfer seminars sponsored by the National Institute for Occupational Safety and Health (NIOSH) on New Technology for Ground Control in Retreat Mining. The seminars were conducted at five locations: Uniontown, PA (March 26, 1997), Norton, VA (April 8, 1997), Pikeville, KY (April 10, 1997), Charleston, WV (April 17, 1997), and Evansville, IN (April 22, 1997). The papers presented here describe several new, highly practical technologies developed by the NIOSH Pittsburgh and Spokane Research Centers3 to improve safety during pillar retreat operations. Two central issues are addressed: pillar design and mobile roof supports (MRS's). Proper pillar sizing is essential for safe pillar extraction. The Analysis of Retreat Mining Pillar Stability (ARMPS) program and its large data base of actual mining case histories are presented. LAMODEL, a second computer program, can be used for analysis of multiple-seam and other complex mining situations. Other papers address pillar design to avoid massive pillar collapses and the proper role of coal strength testing. MRS's have greatly improved safety where they are used for pillar line support. We studied the application of MRS's at 20 mines throughout the Eastern United States. Conclusions regarding the most effective section layouts, cut sequences, and support placements are reported. Field and laboratory tests of MRS's are also described.

Jan 1, 1997

By John W. Kopp

Stemming is used in blasting operations to help contain explosive gases as long as possible. Stemming can reduce airblast, improve fragmentation, and reduce the chances of hot explosive gases igniting methane and dust explosions in underground mines. Stemming is required in underground coal mines but is generally not used in underground metal and nonmetal mines. Some underground metal and nonmetal mines are classified as gassy and can require special blasting procedures such as the use of stemming to minsure the safety of miners. The types and amounts of stemming material that are desirable in underground metal and nonmetal mine blasting to ensure good or improved fragmentation while containing the hot gases are largely unknown. This Bureau of Mines research examined the effectiveness of differing lengths of stemming by measuring stemming ejection times as related to burden movement. With properly stemmed blasts, stemming is contained until some burden movement has occurred. Test blasts at two surface limestone quarries were evaluated using high-speed photography. For the conditions of these tests, a stemming length of at least 26 charge diameters was found to prevent premature stemming ejection. In tests with stemming lengths of 16 charge diameters, the stemming was effective but there was early venting of hot gases through fractures in the rock. Further testing with other rock types, hole diameters, explosive types, and stemming materials as they affect incendivity is recommended.

Jan 1, 1987

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989

By Ronald T. Mayerle

In-1992, the U.S. Bureau of Mines conducted a mineral investigation of the Anderson Mountain study area, including RARE II area 4-942, in Lemhi County, Idaho. The 7,340-ha study area lies within the Salmon National Forest about one kilometer north of the old mining town of Gibbonsville (pop.: 100). The eastern boundary of the study area is formed by the crest of the Bitterroot Range. The crest also serves as the continental Divide, and as the border between Idaho and Montana. The study area lies within the Gibbonsville Mining District, an important past producer of gold from lode and placer deposits. Since the 1870's, several hundred claims for both types have been located in the study area. Thirty-six current (1992) lode claims and two patented claim groups (one lode and one placer) are wholly or partially in the study area. No placer claims are current. In all, twenty-seven lode and five placer properties in and adjacent to the study area were investigated. Workings on the properties included 2 caved shafts; 36 caved adits; 8 open adits; 120 small pits, cuts, and trenches; and 4 large dozed cuts.

Jan 1, 1993

By M. H. Kersten, G. A. Brady, Jerry W. Ramsey

Anthracite samples were oxidized with nitric acid to prepare products representing intermediate stages of oxidation . Similar oxidizing conditions affected different anthracites to varying degrees as characterized by peptization behavior with 0.1 N NaOH . Techniques used in attempts to separate and characterize the products included esterification , absorption spectrophotometry , sublimation , chromatography , electrophoresis , metal salt formation , and solvent extraction . Mellitic acid , either free or in the form of metallic salts , was identified in the acid- soluble products from 10 tests in which the anthracite was treated with nitric acid for periods varying from 24 to 1,000 hours . pentacarboxylic acid was also found in some products . Other benzene carboxylic acids were not present in amounts detectable by the methods used in this study . The acid- insoluble residue from nitric acid treatment varied significantly in solubility behavior toward different classes of solvents . The most effective ones tried included polar oxygenated solvents and pyridine . Infrared spectra of the extracted material indicated that similar compounds were extracted by the different solvents . Aliphatic amines and aniline peptized the residue and o- toluidine reacted with it . Organic material separated from the residue by peptization with dimethylformamide contained 1 percent ash , consisting of more than 50 percent zirconium .

Jan 1, 1964

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable capacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine owners and environmentalists alike.

Jan 1, 1976

By Kenneth M. Earl

This report describes the results of a field study conducted by the Bureau of Mines during 1956 and 1957 on manganese-and iron-bearing mineral deposits in the southern district of Aroostook County, Maine. The work was undertaken to determine the extent of deposits largely concealed under glacial drift and to obtain subsurface samples for manganese mineral identification and research in ore dressing and extractive metallurgy. The investigation was confined to the Westford Hill-Daggett Hill area in Hodgdon Township and to the Stewart prospects and vicinity in Linneus Township. Over 50 magnetic anomalies were mapped by magnetometric surveys in the Westford Hill-Daggett Hill area, Hodgdon Township. The largest anomaly, as outlined by the 1,000-gamma contour, indicates a deposit 3,200 feet long with a maximum width of 350 feet. The smallest anomaly measures about 10 feet wide by 25 feet long.

Jan 1, 1962

By John B. Knaebel

Hammer machines are now widely used for underground sampling and exploration. Their application to such work can be divided into two classes - sampling and testing with ordinary drilling equipment to shallow depths of 22 feet or less, and "long hole" drilling with heavy machines and special equipment to depths of as much as 250 feet or more. In the first category hammer drills are employed for either of two distinct purposes: first, as a means of checking the results of grab or cut samples or, in certain types of ore deposits, as a substitute for these methods; and second, as a method of sampling the ground 5 to 20 feet beyond existing faces and thus aiding in the control of stoping operations or in the direction of development headings, as the case may be. The deep-hole drill, in the second category, has proved to be a valuable adjunct to the old established methods of exploring, end developing ore, provided it is employed under natural conditions to which it is suited, handled by men thoroughly familiar with the technique of its operations, and used with its possibilities and limitations clearly understood.

Jan 1, 1932

By Steven C. Goddard

Since the passage of the Federal Coal Mine Health and Safety Act of 1969, the need for improved duet control methods has become imperative. It has been proposed that one promising dust control technique would be the application of water through the cutter drum. In November of 1972, the Jeffrey Mining Machinery Co., who had been pursuing the development of wet drum miners since 1969, completed the manufacture of a 120M HELIMINER which had sprays in front of the cutting bits on a fixed width drum. On June 27, 1973 Jeffrey and the Bureau of Mines signed the contract numbered B0232060 for the purpose of evaluating "the effectiveness of respirable dust control on a Jeffrey 120M HELIMINER by use of water piped through the head." This evaluation, as described by the contract, was to be accomplished by the collection and analysis of dust samples at various locations of an operating mine production section.

Jan 1, 1974

By A. J. Kraemer

Few important improvements other than the development of cracking processes were made in technical petroleum refining from 1914 to 1919. Refiners were concerned mainly with enlarging their plants and erecting new plants to meet the growing demand for petroleum products. Shell stills operated as a unit or arranged in series for progressive or continuous distillation were the prevailing distillation equipment. Some improvement was made in condensers, but in most refineries of the period coils of pipe immersed in tanks of water were used to condense vapors and cool liquid products of the stills. Heat exchangers to conserve heat and reduce costs were more highly developed at California topping plants than at other plants. In this connection Wadsworth3/states: It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished.

Jan 1, 1941

By J. B. Gayle

Although heated circuits frequently have been employed in the conditioning stases of certain flotation processes, particularly the flotation of fluorite, the control of temperature is not generally considered economically feasible for the flotation of coal. This viewpoint, although widely held, can neither be substantiated nor refuted by reference to published data. Some evidence is available, however, that temperature is an important variable in the floatability of coal as well as other minerals. For example, Gayle and Swelley4 found that contact angles for coal and related substances were definitely dependent on temperature. Bailey and Whalan5 showed that changes in pulp temperature may exert a pronounced influence on recoveries of coal in batch flotation tests. The present laboratory-scale investigation was undertaken to obtain information about the effects of changes in pulp temperature on coal flotation recovery and also on the selectivity of separation possible using different reagents. The results indicated that flotation recoveries were markedly affected by temperature variations when certain reagents, particularly simple aliphatic alcohols, were used. For other reagents, particularly kerosine, flotation recoveries were substantially independent of variations in pulp temperature. Release-analysis results indicated that temperature variations did not greatly affect the selectivity of separation possible with the reagents tested.

Jan 1, 1961

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By Ted A. Lewtas

The effectiveness of induction fans in ventilating dead headings was studied in the laboratory and underground. The following fan attachments were evaluated: a. Aerodynamic nozzle b. Various lengths of vent tube c. Honeycomb airflow straightener. Various fan locations were also tested. The following conclusions were reached: a. A nozzle on a fan located against the drift wall gives the greatest jet penetration distance. b. Air straighteners are ineffective in increasing jet penetration. c. Induction fans are ineffective in removing contaminants from dead headings without sufficient main ventilation flow.

Jan 1, 1980

By H. Leitch

In laboratory experiments, the Bureau of Mines investigated melting, quenching, and sulfuric acid leaching of alumina from mixtures of albite and anorthite, and from anorthosites containing 26 to 32 percent alumina. Variations in pouring temperature, quenching and leaching conditions, were studied with respect to the extraction of alumina and impurities. Virtually all of the alumina was dissolved by leaching melted and quenched California anorthosite in boiling 16-percent sulfuric acid solutions for 15 to 30 minutes. The leach solutions were readily separable from the solid residue by conventional thickening and filtration techniques. Only 2 to 5 grams of SiO2, Fe2O3, or CaO dissolved per 100 grams of alumina. The quantity of SiOz in solution varied inversely with the duration of the leach and with the concentration of the H2SO4 solution used. Melted and quenched Wyoming and Minnesota anorthosites with SiO2:CaO weight ratios of 4.3 and 3.2, respectively, were less amenable to sulfuric acid leaching than California anorthosite with an SiO2:CaO weight ratio of 5.3. However, excellent results were obtained on the Wyoming and Minnesota anorthosites by the addition of SiO2 to these materials before melting, in quantities sufficient to adjust the SiO2:CaO weight ratios of the furnace charges to between 4 and 6.

Jan 1, 1966