Search Documents

By H. M. Smith

[ ]

Jan 1, 1927

By J. D. Davis

"Introduction.Sixty years ago, M. Berthelot found that ethylene could be selectively absorbed from gaseous mixtures by concentrated sulphuric acid, and that the compound formed by the chemical union of the gas and acid was readily decomposed by heating with water, yielding ethyl alcohol. Only within the last few years has there been any attempt to make use of this discovery technically.Bury*, working in England at the Skinningrove Iron Works and on a commercial scale, developed a technical method for converting, the ethylene of coke-oven as into alcohol. With a gas containing less than 3 per cent of ethylene, he obtained a yield of 1.6 gallons of alcohol per ton of coal carbonized.De Loisy** perfected a technical method for treatment of coke-oven as for alcohol. Evidently this work was carried out on a semi-commercial scale. His method is based on the use of catalytic agents for hastening the absorption of ethylene by sulphuric acid. He uses part of the spent acid for drying the gases and pact for the manufacture of ammonium sulphate. Excess acid is reconcentrated by waste heat. Others have worked on the problem, but so far there has been no large recovery of ethylene from coke-oven gases. The chief difficulty seems to lie in the low efficiency (about 50% of methods and tae relatively low concentrations of ethylene in the gases treated. Gas from Trent amalgam*** contains much larger percantages of ethylene than does coke-oven gas, as Will presently be shown, and if it should ever prove practIcal to treat industrial ;as for alcohol, this gas would offer attractive possibilities,* Bury, Ernest, Ethylene as Alcohol from Coke-Oven Gas: Gas Journal' Vol. 148, D. 30, 1919, pp. 718.** DC Loisy, M.E., Sur un procede' industrial de fabrication syntlotique de l'alcool et de l'ether a partir des gaz de distillation de la houil Comp Rend, vol. 170, Jan. 1920, p. 50-3.*** A paste consisting of approximately part oil such as that obtained as for cleaning coal. See Perrott. in cleaning coal, Chem 3 parts finely pulvarized coal and 1 final product in the Trent, process StJ, and Kinney, S.P. The use of oil Vol. 35 August 3, 1921, p, 183.. & Met."

Nov 1, 1922

By E. S. Leaver

The mineral value in the ores from the Mother Lode mining districts of California is almost entirely gold, Although many mines have produced extremely high-grade ore the usual mill grade averages approximately $7.00 gold per ton. Fully 80 per cent of the gold has been and is now being recovered by amalgamation. Various methods have been introduced to recover the gold that was not obtained by the amalgamation processes. They include vari¬ous kinds of gravity concentration which in some cases were followed by chlorination or cyanidation. The usual practice includes only stamp battery, plate-amalgamation, and vanner concentration. In the very early practice the tails were run to waste through the main drainage streams of the different mining districts. During later years very large storage dumps have been impounded. These old tails, together with those being saved from present mills, furnish the problem discussed in this article. The clean sand portion of these mill tails is amenable to the usual cyanidation. The slime portion contains the major amount of the gold lost, but it also contains 1-1/2 to 3 per cent carbon, which precludes direct cyanidation of this part of these low-grade waste tails. The black carbonaceous slime portion is the particular problem considered in this report.

Jan 1, 1930

By R. T. DeWoody, W. C. Miller, W. Chester

Studies were made to determine the effect of the shape of a pneumaticrock- drill exhaust muffler on its efficiency, and the origin and reduction of exit noise from the mufflers. Tests of mufflers of three different shapes proved that the shape is not critical and that a muffler could be incorporated into the shell of the drill. Petal diffusers are beneficial in reducing exit noise but add another projection to the machine. Increasing the number of exit openings while maintaining the same area of exit opening has a markedly beneficial effect on the exit noise and appears to be the most satisfactory treatment.

Jan 1, 1964

By G. B. Gait

This report is the fifth in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region. A catalog of the microfilmed maps of 47 of 49 major mines and 18 independent mines in the Southern field is presented. Previous reports included catalogs of microfilmed maps of mines in the Eastern Middle field, the Wyoming and Lackawanna Basins of the Northern field, and the Western Middle anthracite field.

Jan 1, 1978

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

INTRODUCTION The pager phones used in many underground coal mines are battery- operated, party-line telephones with provisions for loudspeaker paging. The system is two-wire, non-polarized, and is operated by self-contained batteries. Many of the individual units are certified as permissible. Requirements for installation are specified in state and federal regulations, such as in the Code of Federal Regulations, Title 30, Mineral Resources, Part 75. The major federal regulations that affect communication in coal mines are noted below, with a brief description of the subject matter in each of the relevant paragraphs. Refer to the cited paragraphs of Title 30 for explicit details of these regulations. (This brief description is for reference purposes only.) Minimum Requirements (paragraphs 75.1600, 75.17 13-2, and 75.1003-1) Approved telephone or two-way communication will be provided between the surface and each main shaft landing and each working section ; to the nearest medical assistance; and shall be protected from contact with trolley wires or trolley feeder wires. Installation Requirements (paragraphs 75.5 16-2, 75.52 1, and 77.508-1 ) Communication wires will be supported on insulated hangers, attached to messenger cables, or buried, to protect against mechanical damage ; installed opposite trolley wires; and insulated near power conductors . . . each cable will have lightning arresters within 100 feet of going below ground . . . and arresters will be provided wherever telephone wires enter a building. Wire and Cable Requirements (paragraphs 75.5 16-2, 75.5 17, and 75.52 1) Communication cable means two or more insulated conductors, covered by an additional abrasion-resistant covering; power wires and cables shall be adequately insulated and fully protected; and lightning arresters shall be connected to low-resistance grounds, more than 25 feet from neutral grounds.

Apr 1, 1975

By L. B. Pankratz

The heat contents of the sesquioxides of erbium, holmium, thulium, and ytterbium (Er203, Ho203, Tm203, and Yb203) in the cubic crystalline form were measured over the temperature range from 298° to 1,800° K. The erbium and holmium sesquioxides gave regular heat content-temperature curves. Thulium sesquioxide had a minor thermal anomaly near 1,680° K, with a heat absorption of 310 cal/mole; similarly, ytterbium sesquioxide had a minor anomaly near 1,365° K, with a heat absorption of 150 cal/mole. The heat content results are presented in both tabular form (at 100° intervals) and in algebraic form. Entropy increments, corresponding to the tabulated heat content results, also are listed.

Jan 1, 1963

By G. E. Walden

The Bureau of Mines is currently engaged in a continuing investigation of the thermodynamic properties of certain inorganic compounds. As a part of this investigation, the heat contents of bismuth and cerous chlorides were measured throughout the temperature ranges of 370° to 630° K. and 370° to 1,200° K., respectively. Equations representing heat contents as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate heat contents at selected temperature intervals ranging from the ice point to 650° K. for bismuth chloride and to 1,200° K. for cerous chloride; also, the heats of fusion of both compounds were calculated at their respective melting points. EXPERIMENTAL Materials The cerous chloride used in this investigation was supplied by the National Carbon Company of Cleveland, Ohio. A chemical analysis indicated Ce 56.57 percent and Cl 43.39 percent. No attempt was made to purify the compound or identify impurities since the analysis showed only about 0.04 percent total impurities. Reagent grade bismuth chloride was used without additional purification.

Jan 1, 1961

By S. C. Schaefer

Thermodynamic properties of indium oxide (In203) have been studied with a high-temperature galvanic cell employing stabilized zirconia electrolytes. In the temperature range 790° to 1,230° K the free-energy change for the cell reaction 21n(1) + 3Cu20(c) = In203(c) + 6Cu(c) together with the standard free energy of formation of cuprous oxide gives the standard free energy of formation of indium oxide from the elements as ?Gf° = -218.78 + 75.34 X 10-3T ±0.7 kcal/mole. A third-law analysis yields the standard enthalpy of formation: ?Hf°298.15 = -221.5 kcal/mole.

Jan 1, 1971

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By D. D. Fischer

Recovery and separation of molybdenum and rhenium from a process solution was accomplished by a technique developed by the Federal Bureau of Mines involving a combined solvent extraction and activated carbon adsorption procedure. The processing sequence required treatment of the solution with S02 to reduce the chlorate ion and adjust the pR prior to solvent extraction of molybdenum and rhenium with a tertiary amine. Molybdenum and rhenium were stripped from the organic phase with an NH40H solution, and the strip solution was then passed through activated carbon to preferentially adsorb the rhenium. After washing entrained molybdenum from the column with a brine solution, rhenium was eluted with an MeOH-H20 mixture. The activated carbon was regenerated with water. Molybdenum was recovered as (NH4)6Mo7024 by evaporating the column effluent. Rhenium in the column eluate was reextracted with a tertiary amine, stripped from the organic phase with dilute NH40H, and recovered as NH4Re04 by evaporating the strip solution. The final (NR4)Re04 product contained < 80 ppm impurities. Sodium sulfate was crystallized from the first solvent-extraction raffinate by lowering the solution temperature to 0° C. Precious metals contained in the original process solution were adsorbed onto the activated carbon.

Jan 1, 1975

By G. W. Jones

The determination of the ignition temperature of diethyl ether and ethylene in air and omen which is described in this report was made primarily for comparison with similar determinations of other compounds in the same apparatus and using the see laboratory technique. The investigation was conducted at the Pittsburgh Experiment Station of the United States Bureau of Mines with the cooperation of Merck & Co., Inc.

Jan 1, 1935

By T. R. Strombotne

The purpose of this report k to document a contract undertaken by TSA Systems, Incorporated for the United States Bureau of Mines to develop a commercially available source of a continuous, working,, level detector for the measurement of radon daughter products in various working environments. The basic radon measuring technique was devised by Robert Droullard and Robert Holub and has been applied here. For further details or purchasing information contact: TSA Systems, Incorporated 4919 North Broadway Boulder, Colorado 80302

Jan 1, 1982

By Lucia Kuizon

The Antimony RARE II area is underlain principally by Mesozoic igneous rocks associated with the Sierra Nevada batholith. The San Andreas fault zone is near the southern boundary. Metallic mineral deposits are associated with the fault zone. These deposits were formed from magmatic solutions, and tend to be along shears and fractures within the country rock. Marble and dolomitic marble deposits occur in Paleozoic roof pendants or inclusions in the Mesozoic intrusive rocks in the area (Troxel and Morton, 1962, p. 52).

Jan 1, 1982

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By Robert J. Evans

The Hopper-Feeder-Bolter (HFB) is a prototype multifunctional machine designed to improve productivity by minimizing continuous miner place changes. It is designed primarily to work beside a two-pass continuous miner, bolting on one side and then place changing to bolt the other side while simultaneously providing a surge car and lump breaker located directly behind the continuous miner. Surface testing was conducted at the Bureau of Mines Mine Equipment Test Facility (METF) to evaluate overall system performance and reliability. Tests were conducted to evaluate place changing, tramming, lump breaking, roof bolting, drawbar pull, conveying, temporary roof-support (TRS) capacity, lighting, and noise. Surface test results indicate the HFB is ready to be tested and evaluated underground in a production mode.

Jan 1, 1988

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By Thomas L. McVay

Laboratory batch and pilot plant flotation tests were made to determine the feasibility of recovering commercial grade kyanite from a quartzite- kyanite rock from the Graves Mountain, Ga., deposit. Best results in laboratory and continuous tests were obtained using sodium carbonate for pH control, citric acid for quartz depression, and oleic acid as the kyanite collector. Over 80 percent of the kyanite was recovered in a concentrate analyzing 56.8 percent Al203 and 3.8 percent hydrochloric acid soluble Fe203. Subsequent treatment of the flotation concentrate by magnetic separation reduced the acid soluble Fe2O3 to 0.6 percent and increased the alumina content to 59.2 percent. Acid leaching of the concentrate gave a product analyzing 59.7 percent Al203 and about 0.1 percent Fe203. As a result of the beneficiation research, a commercial kyanite flotation plant was completed in September 1962 by private industry.

Jan 1, 1963