Search Documents

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By W. E. Cobb

The financial implications of environmental liabilities are becoming staggering, particularly for mining companies. The Environmental Protection Agency's (EPA) Record of Decision (ROD) list for Superfund mining sites has some pretty hefty financial commitments, such as the $10 million operable unit remedy for the Yak Tunnel at California Gulch (in Colorado) or the $40 to 60 million remediation at Bunker Hill (in Idaho). These costs are driven by the large volume and areal extent associated with historical waste management practices at mining sites. (It's difficult to have a low-cost remedy for a 20-square-mile site.) Unfortunately, there are other ways of generating environmental liabilities besides Superfund, such as non-compliance with Clean Air Act provisions, stormwater permits, or National Pollutant Discharge Elimination System (NPDES) permits. In the last 2 years, EPA has increased enforcement in its regulatory programs, which has resulted in increased fines and criminal actions. Leaders in other industries (primarily the chemical and manufacturing industries) are viewing environmental liabilities as a strong motivator to select engineering approaches carefully based on technical, legal, economic, and philosophical perspectives. Industry interest in waste minimization programs comes from the concept that it is economically advantageous not to create waste in the first place. Waste minimization programs typically balance increased front-end capital investment with the minimization of potential long-term environmental liabilities as a way to achieve the lowest total-or life-cycle-cost. A side benefit of waste minimization programs is that they tend to improve overall regulatory compliance. Waste management practices are also becoming philosophical, as evidenced by a May 11, 1992, Business Week article: Companies that incorporate innovative thinking on sustainable development will do more than clean up or prevent their own pollution. They'll make and distribute a product more efficiently than ever, worry about its lifelong environmental impact, plan for recycling, and get their suppliers on the bandwagon. This type of approach will require a new mind-set, new tools, and adjustments throughout the organization. A key aspect of waste minimization or life-cycle waste management programs is the incorporation of environmental costs into economic analyses that compare various waste management alternatives. However, the incorporation of environmental costs into an economic analysis can be more difficult than initially thought. As noted above, new tools-or even a new toolbag-are needed, such as new accounting methods that track and assign the true lifetime environmental costs of a particular product. One piece of the new toolbag is life-cycle cost analysis, which is discussed in this paper. To simplify the discussion, this paper looks at the total costs associated with a given mining site. The concepts presented in this paper, however, can be applied to any mine waste management decision. The ultimate extension of life-cycle costing, as presented in the Business Week article, is to include the potential environmental costs throughout the life of a metal. At this point, I am perplexed on why, let alone how, to include the potential downstream environmental costs (i.e., the costs associated with smelting, manufacturing, use, and recycle or disposal) throughout the life cycle of mined copper, lead, or zinc.

Jan 1, 1992

By R. C. Fox

The geophysical aspect of reconnaissance marks the beginning of extensive computer applications supporting development of a mine. Although there are some storage and retrieval applications in geology, and some statistical analysis in geochemistry, large-scale compilation, reduction, and interpretation of mineral resource data are initiated in reconnaissance geophysics. The reasons for this fact are quite simple. Geophysics is oriented toward quantitative evaluation of areas of interest, and methods of data collection are automated to the extent that large amounts of analog and digital information are recorded. The large volume of data must be interpreted in a reasonable time. Furthermore, some modeling problems involving complex numerical solutions could not be attempted without the computer. Therefore, the computer is essential to the success of an exploration project using geophysics. For example, aeromagnetics is a common technique for reconnaissance examination of areas associated with sulfide systems and porphyry deposits. An area covering 161 X 161 km (100 X 100 miles) may be flown with a 1.6-km (1-mile) line spacing yielding 10,000 line miles (16,093 km) of data. If only 10 measurements are recorded per mile, 100,000 data points, including location and magnetic field intensity, must be reduced and stored for quantitative interpretation. Computer applications often represent a significant investment in manpower and hardware. It is desirable, therefore, to initiate an engineering approach to the application of computers to geophysics. By this it is meant that computer programs and systems should be formulated, developed, and implemented in a disciplined manner such that their usage is dependent only on the application and not on the individual doing the programming. In other words, computer application, development, and usage should evolve beyond the personal gadget phase to an important applied technology. Geophysics has evolved over the past two decades in a course parallel to computer hardware development. During the sixties, the computer became large enough and fast enough that complex models required by geophysics could be solved. Automation also relieved the geophysicist from routine manual calculations. During the seventies, computing power in¬creased and applications expanded from two-dimensional problems to three-dimensional modeling. Moving into the eighties, as computer hardware costs will significantly decrease, the major expense of computing will be the manpower required to develop, implement, and use an application; therefore, improved programming techniques and applications software engineering methods will be used to optimize and preserve this investment. This chapter presents a general overview of computer methods in geophysical reconnaissance; it is divided into two parts: geophysical methodology and software engineering.

Jan 1, 1979

By J. D. Morgan

Introduction In 1987, the US economy continued to grow steadily, reaching an annual rate of $4.6 trillion in the last quarter. The value of domestically processed mineralbased materials rose slightly to $250 billion. The value of US metals rose sharply to more than $7 billion. Industrial minerals rose slightly to $18 billion recycled scrap was valued at $4 billion. Metal prices rose sharply toward year-end. A number of mining and metal companies experienced increased profitability, fostering more optimism about the future. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and federal debt continue to rise. 244 million citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production fell 9% to 7.1 million units, but truck and bus production rose 9% to 3.8 million units. New housing starts fell 10% to 1.6 million units. Excess productive capacity exists not only in the US, but also in many other countries. Consequently, the US mineral industry is encountering stiff competition from others, as well as increasing competition from newer engi¬neered materials. Domestic production of plastics rose 9% to 25 Mt (27 million st) - on a volume basis, double all metals. Some 7% of petroleum goes to make petrochemicals including plastics. Imports of nonfuel mineral-based materials in 1987 were valued at $37 billion and exports at $24 billion. Imports supplied a significant proportion of total US consumption of several important mineral materials, including many classified as strategic and critical. In December, the Congress mandated that any major changes in stockpile goals be made only by law, and that the Department of Defense submit annually detailed stockpile supply/demand analyses. Concern about apartheid in South Africa continued, resulting in increasing interest about chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The National Critical Materials Council continued to monitor the US materials position. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve continues in effect through Sept. 30, 1989. Under the DPA, the US Bureau of Mines maintains the Emergency Minerals Administration. Further consultations were held with Canada to strengthen the North American defense industrial base. Coal production, 60% from open pits, rose 2% to 825 Mt (910 million st) valued at $21 billion. Nearly four-fifths was burned to generate 56% of US electricity. Exports included 42 Mt (51 million st) of metallurgical coal and 24 Mt (27 million st) of steam coal, with a total value of $3.3 billion. Domestic petroleum production fell 5% to 480 Mm' (3 billion bbl). Uranium mining, including recovery from phosphates, fell 4% to 5.9 kt (6500 st). Nonfuel minerals Major metals: Raw steel production - a major consumer of many minerals - rose 7% to 79 Mt (87 million st). Domestic iron ore production rose 11% to 44 Mt (48 million st), about 96% pelletized. Net imports, though, fell 8% to 11 Mt (10 million st). Raw steelmaking capacity fell 6% to 102 Mt (112 mil-

Jan 5, 1988

By John A. Kaufman, Terry D. Vandell

Recent mining regulations have increased the need for detailed engineering and environmental information pertaining to the hydrogeologic environment in mining areas. The cost of obtaining such hydrogeologic information has also increased. After mineralization of potentially economic grade ore and tonnage has been identified, and after completing preliminary mining feasibility studies (suggesting that development is merited), a second exploration phase can incorporate a simple, cost-effective baseline hydrogeologic data reconnaissance program that is limited but useful. Using exploration drill holes only, this program can provide a direct indication of where ground water is encountered. Also, reasonable estimates can be made on the relative production of water from various water-bearing strata, a composite potentiometric surface map can be prepared, and the general chemistry of the ground water can be characterized. This article outlines what typical baseline hydrogeologic data are needed and describes how it can be easily obtained during exploration drilling. Introduction Major engineering and environmental ground water parameters can be identified early in a project by using, drill hole data obtained from a mineral exploration program, designed by the mine geologist and hydrogeologist. Most importantly, data obtained in the exploration drilling program can be used to design a logical, defensible, and cost-effective baseline ground water data reconnaissance and monitor well program, which would be required for mine design and ultimately for mine permit approval. Drilling Where possible, exploration drill holes should be drilled with conventional rotary drilling equipment using air or, if necessary, water as the drilling fluid. Rotary air or water drilling generally allow good delineation of the first major saturated or water-bearing zone. If mud must be used during drilling, distinct hydrogeologic zones can still be defined, although the task may be considerably more difficult. Water Levels Static water levels can be obtained from selected exploration drill holes at specific depths while additional boreholes are drilled. Such measurements should not, however, be conducted until the hole has been developed with air (no water) and has stabilized at each of the depths to be measured. Such water-level information can be particularly useful when more than one aquifer exists. Where mine development is eminent, the hydrogeologist should install 50-100 mm (2-4 in.) diameter PVC casing in select drill holes. The PVC should be slotted, gravel packed, and properly sealed so additional hydrogeologic data can be collected for specific hydrogeologic zones at a later date. Such data could include water level information, permeability estimates based on injection and /or pumping tests, and water quality data. Where casing is not installed in drill holes, or when the drill holes are abandoned, the holes should be properly grouted and back-filled to the ground surface to prevent potential future ground water contamination. Monitoring Air Lift Water Production Estimates of the relative production from various water-bearing strata can be obtained from selected exploration drill holes. If ground water is encountered, its air lift (ground water flow) production can be measured at distinct intervals using a surface water flow measuring device, such as a portable Parshall

Jan 2, 1983

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By David M. Parkes, Mike Fisher

In 1947, coal production in Western Canada was 10 Mt (11 million st) which predominantly came from 120 underground mines. By 1968 production was down to 1 Mt (1.1 million st). Production in 1981 was back up to 29 Mt (32 million st), but only 1.5 Mt (1.7 million st) of the total was from underground mines. In fact, because of competition from open-pit mines, only two underground mines were operating in 1981-the McIntyre and B.C. Coal mines. While several other underground mines are being planned, this article will deal with only the two in production. Geology The geology in Western Canada is frequently complicated; hence only more regular deposits are mined. Coal is generally thick, often steeply pitched and usually soft or well cleated. The 5000-km (3,100-mile) coal belt that runs from the Yukon to Mexico is well developed in Western Canada. It is divided into two distinct regions-the Rocky Mountain Lower Cretaceous coals and the mostly uniform level Upper Cretaceous coals of the plains area to the east. Isolated pockets of coal occur at Vancouver Island and Hat Creek. Hat Creek's massive 300-m (984-ft) thick geologically recent lignite deposit is 250 km (155 miles) inland. Geography The infrastructure of Western Canada is shown in Fig. 1 along with the locations of the two mines. Both rely on exports of premium low volatile metallurgical coal mostly to the Pacific Rim. The rail distance from both mines to port is 1100 km (684 miles)-accounting for a significant portion of the sales cost of the coal. Mining Methods Two main mining methods are used-room and pillar and hydraulic. Longwall has been attempted and is being considered again. In the past, a simple hand method used gravity to help mine most of the coal on steep pitches. Levels were driven in the seam, rising slightly to assist in draining. On the advance, mining would start at the upper level, usually from adits driven in the side of the mountain. Rooms or angles were driven up 100 m (328 ft) at a suitable angle for the coal to flow down. On retreating out of the level, the pillars would be taken, starting from the highest point, using batteries to stop coal or rock flushing down the room. Batteries consisted of three to six stout wooden posts set at an angle to resist material flow. Coal loading was directly from chutes at the bottom of raises into 1- to 2-t mine cars hauled by diesel or battery locomotives. Often output was restricted by the supply of empty cars. Mechanization began in the 1960s but was difficult in these conditions. Mines such as Canmore and Coleman continued operation into the 1970s but closed because steep seams, high methane emissions, and faulting made mining difficult. McIntyre Mines The McIntyre mines are located 360 km (224 miles) west of Edmonton, Alberta, in the foothills of the

Jan 4, 1983

By Ing. H. Kellerwessel, Ing. M. Esna-Ashari

This paper refers to the new crushing and grinding process, invented by Professor Schonert (Ref. 1), Clausthal, Germany. The process is known as high pressure particle bed comminution or interparticle crushing. Several papers already describe fundamentals of the process, the equipment used, results of lab size and large scale tests and the first results of commercial operations (Ref. 2 to 7). Of course, we will treat the topic from the perspective of a downstream gold ore upgrading or leaching process. Some recently executed testwork indicates that the process provides special advantages in this field. To describe the process generally, in view of the already existing publications.

Jan 1, 1998

By S. R. LaBrooy, J. Avraamides

Thermal reactivation of eluted carbon is an essential part of most carbon-in-pulp gold recovery plants. The effectiveness of the reactivation procedure depends on the nature and level of contaminants adsorbed on the carbon, the efficiency of the elution and the temperature, residence time and atmosphere within the kiln. The most commonly used kilns are evaluated in terms of their operating parameters and performance. Data obtained both in the laboratory and in the field emphasize the importance of carbon feed moisture content, kiln atmosphere and carbon conditioning on the activity of the kiln product.

Jan 1, 1998

By P. R. Bailey

The use of carbon for the recovery of the gold dissolved in cyanide leaching began with a pilot unit at Barberton in 1977. This was quickly followed by larger scale plants at Modderfontein (1978), President Brand (calcine 1980), Western Areas (filter tails 1980) and Beisa (primary ore 1981) and has grown to become the preferred process. There are currently 34 operations that use the carbon in pulp/leach process which accounts for 35 percent of South Africa's gold production. The size of individual plant varies over a wide range.

Jan 1, 1993

By H. E. Epstein, B. K. Parekh, W. M. Goldberger

Comminution is the single most expensive operation in mineral processing. It consumes about 50% of the energy required for mineral extraction (Agar, 1976). Current comminution technology is both energy-intensive and inefficient. A novel noncontact comminution process concept was developed in this study, whereby selective lib¬eration of minerals from an ore could be potentially achieved. The process involves application of electric and ultrasonic energy to liberate minerals from gangue particles. Introduction The mineral industry is a large user of energy in the US. Energy usage is increasing as the grade of ores processed decreases. It is es¬timated that comminution of ores uses about 32 000 kWh (115 trillion kJ), or 2% of the electric power produced in the US (NMAB-365, 1981). Among other minerals, ce¬ment, iron, and copper processing plants are the largest users of en¬ergy in comminution. Very little of this energy used in conventional grinding (about 1%) is used to gen¬erate new surface. The remainder is wasted (Table 1). Thus, there are substantial energy-saving and economic incentives to improve the efficiency of crushing and grinding techniques for mineral recovery. With an energy efficiency of only 1%, it would seem possible to devise methods to significantly improve comminution technology. This requires that breakage force be applied only where needed, not indiscriminately as in a conven¬tional ball mill (NMAB-365, 1981). Can apparatus and methods be de¬ veloped for large-scale commer¬cial use that allow energy to be fo¬cused at intergranular bounda¬ries? If this can be done, mono¬mineral grains would remain in¬tact and the grinding action would be selective and substantially more efficient. The novel comminution process concept described in this paper uses a combination of electric and ultrasonic energy. This energy breaks the ore and selectively lib¬erates minerals. The process has also been termed a two-stage or electroacoustical comminution process (Goldberger, Epstein, and Parekh, 1982). The mineral grain boundary is usually the weakest area in an ore. By applying electri¬cal energy to the ore, the rock frac¬tures mostly at grain boundaries. At the same time, the electric shock creates secondary hairline fractures in the ore. Additional application of ultrasonic energy to this ore provides further break¬age. The concept was proven on a molybdenum porphyry ore but needs additional study. Technical Background There have been substantial im¬provements in milling machinery and grinding operations, but rela¬tively few attempts have been made to develop alternatives to conventional impact milling. Sev¬eral methods, however, have been investigated that relate to this study. In the early 1970s there was considerable interest in a size re¬duction method known as the Snyder Process (Cavanaugh, 1972). It involved charging coarse ore into a pressure chamber, pressur¬izing with a gas, and activating a quick-opening (15 msec ) dis¬charge valve that connected the chamber to a discharge duct. This allowed solids to fluidize and ac¬celerate, subjecting the material to a variety of impulse phenomena that caused the desired size reduction. Other nonimpact means of achieving breakage and selective size reduction have been de¬scribed in technical and patent literature. Kanellopoulos and Ball (1975) considered using heat to induce thermal stress in quartz¬ite. This would cause cracking and, thus, increase grinding efficiency. The use of electrical energy to induce thermal stress was studied by the General Elec¬tric Co., in cooperation with the Montana School of Mines, under a research grant from the Anaconda

Jan 9, 1984

By Michael G. Nelson, Amy Richins, Ashley Hodgson, W. Pratt Rogers

"Sociotechnical systems are everywhere in the modern industrial world. Sociotechnical systems describe how humans interact with technology throughout a variety of processes. These systems are prevalent in modern industrial settings, such as operating mines. Safety and health management systems (SHMSs) are complex sociotechnical structures designed with the aim of managing and reducing occupational risk. U.S. mining companies are voluntarily adopting SHMSs to supplement regulatory safety compliance efforts. Like all complex sociotechnical systems there are a wide variety of approaches and adoption philosophies around a SHMS. Many SHMSs suffer from high levels of redundancies, which manifest themselves in diverse ways: duplicate processes, forms, permits, and tracking mechanisms. These redundancies have severe impacts on the overall system and absorb critical culture and leadership “energy”. A recent study initiated by the University of Utah and sponsored by the Alpha Foundation is investigating the effectiveness of SHMSs across 15 different U.S. mining sites. A large amount of data has been captured to help characterize elements of SHMSs and correlate their impacts on safety outcomes. Many variables were assessed in the study. Those of importance to this paper are the variables describing the robustness of the sociotechnical aspects of the SHMS. Two such variables are the overall integration of the SHMS within the whole system and how data is managed. Data management in this context deals with the approach to capturing, analyzing, and acting on data within the system. As well, systems are integrated around controlled, data-sharing mechanisms. It has been found that wide variety of approaches has been taken to integrate the SHMS within the governing management philosophy at a given site. A series of case studies is presented that develop some specific best practices for proper data management and integration of SHMSs.Introduction and Project Background Managing occupational health and safety can be done in many different ways, and with many different approaches, but is often based on the host country’s regulatory and industrial culture. However, many companies have extended their effort beyond the regulatory requirements of their host nation and have implemented Safety and Health Management Systems. The goal of these efforts is to reduce and eliminate occupational risk. Many health and safety practitioners have a hard time justifying various elements of health and safety management. There is a lack of institutional knowledge that measures and assesses the effectiveness of these Safety and Health Management System (SHMS) elements. To better understand the effectiveness of SHMSs the Alpha Foundation has funded a research project with the University of Utah. The title of the project is “Characterization and Effectiveness of Safety and Health Management Systems in the U.S. Mining Industry.” The research team will assess the SHMSs of 15 United States mine sites. The outcome of the project will be a method to characterize the strength of the SHMS elements, assess a culture and leadership index, and finally establish correlations between elemental risk and safety outcomes. The study is currently in progress. However, many important outcomes have already been observed, particularly on the data management practices within an SHMS."

Jan 1, 2017

By Dale S. Preece

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is a research facility located in Southeastern New Mexico. The WIPP is being developed by the U. S. Department of Energy (DOE) to demonstrate the safe storage of defense-related radioactive wastes in bedded salt. Since the WIPP is a research facility. a number of large-scale in situ experiments have been planned and are currently under construction (Munson, 1983). These experiments were designed to study various aspects of nuclear waste storage in bedded salt such as mechanical responses and creep closures of drifts, thermal response due to heated canisters, and thermally-induced fluid migration. One purpose of the WIPP is to develop and demonstrate a general predictive structural analysis capability for a bedded salt repository. One set of experiments, called the Geomechanical Evaluation (Room G), is heavily instrumented to study the creep around several rooms with different configuration. A Layout of the Geomechanical Evaluation room is shown in Figure 1. One portion of it consists of wedge shaped pillar where two drifts intersect at an angle of 7.5 degrees. The pillar can be seen at the bottom of Figure 1. One purpose of the wedge pillar experiment is to study progressive pillar failure in the tip region. Another is to determine how nonuniform pillar thickness affects creep closure of the drifts. An important aspect of the experiments is the correlation between experimental data and corresponding pretest finite element analyses of the site. The finite element simulations serve two purposes. First, the computer simulations aid in understanding the experimental results by providing calculated stress. strain and displacement fields that cannot be measured directly. Second, comparison of calculated and measured drift closures serves as a method for validating or improving the finite element models and the constitutive models employed. The wedge pillar geometry required a 3-D finite element creep calculation. Results from these 3-D calculations will be presented in this paper. A 2-D plane strain double drift model which approximates the wedge pillar geometry at a slice perpendicular to the drift has also been performed and will be compared to the 3-D results in this paper. FINITE ELEMENT COMPUTER PROGRAMS Two finite element computer programs. JAC (Biffle, 1984) and JAC3D (Biffle. 1986), were used. JAC is a 2-D finite element program developed for quasi-static analysis of non-linear solids. It employs the conjugate gradient iterative technique to obtain a solution Spatial integration is performed using a single gauss point in each four node quadrilateral element. An hourglass viscosity technique is used to control the zero energy modes that occur with single point integration. The single point integration combined with the explicit nature of the program and exploitation of CRAY-1 computer architecture results in very efficient execution J4: results were compared to results obtained with eight other 2-D structural creep computer codes in the second WIPP benchmark exercise (Morgan, 1981) JAC3D was derived from JAC to treat 3-D finite element models and has many of the same characteristics including single point integration and hourglass viscosity. These characteristics have made 3-D creep analyses more reasonable by significantly reducing computation time The first exercise of the creep capability

Jan 1, 1986

By Dan Xu, Song. Gaofeng, Zhen Wei, Zhihe Wang

"With decades of development and exploitation of coal resources, the first batch of coal-based cities in China are faced with the challenge of economic shrinkage and environment deterioration due to the rapid resource exhaustion and single industrial structure. Nowadays, as a policy instrument for sustainable development, a nationwide circular economy mode has been implemented during the design and planning of new coal mines to address the challenges arising from economic depression, energy shortage and environmental pollution. It should be mentioned that several national coal bases and most of constructing and planning coal mines are located in the underdeveloped areas in the Midwest of China which means that the distance between supply source for energy resources and the demand market is significantly increased. Moreover, the eco-environment vulnerability in these rural areas should be taken into serious consideration. Therefore, after comparison and analysis with several successful coals based and diversified circular industry chains, this paper presents a case study on the circular economy park (CEP) in the northwest of Shanxi Province. Through discussion and evaluation of ‘1+3’ mode in the CEP, this paper aims to enhance the understanding of coal mine sustainable development and shed light on the relationship between resources exploitation and local economic development.1. Introduction Earth's fossil energy resources are crucial to both economic prosperity and human well-being. Taking coal mining and consumption as an example, coal has been widely used to generate electricity since the 1880s, and more than 40% of the electricity globally is provided by coal nowadays. However, as one of the largest worldwide anthropogenic sources of carbon dioxide releases (39% of global CO2 emissions), the extensive excavation and utilization of coal have brought a series of side effects to both natural environment and human health (Wikipedia 2017). As the largest coal producer and consumer in the world, China is leading the list over the past decade (as shown in Figure 1) (BP 2016). The excavation and utilization of coal resources have made a crucial impact and irreplaceable contributions to China’s industrial development and economic prosperity (Long and Zhang 2009). However, most of the air pollution in China are also attributed to the simplified and extensive exploitation of coal resources, e.g., 90% of SO2, 67% of NO, 70% of smoke ashes, and 70% of CO2 in 2016. In recent years, most of North China and the developed coastal areas were wreathed by smog due largely to the oversimplified extensive utilization of coal, suggesting that the development patterns of coal utilization need to be reshaped so that both the biosphere and humanity could thrive equally."

Jan 1, 2017

By A. Ballester, F. Gonzalez, M. L. Blázquez

Pyrometallurgical process are usually used to recover valuable metals from metal sulphide concentrates. However, their use is diminishing as the cost of energy rises and pollution controls become strictes. An alternative method of treatment sulphides could be bacterial leaching due its simplicity and negligible contamination (1-2). This process is presently used commercially to re cover metals such as Cu and U from low grade ore concentrates. In spite of numerous researchs during recent years (3-5) there exists very little kinetic data concerning the speed of bioleaching process. The kinetic analysis of bacterial activity is related with the metabolism and growth of microox ganisms . This fundamental information permits ma- king the best utilization of bacterial oxidation and to suggest techniques which might increase the production of the products desired. However, bio- kinetic models are especially complicated due to the existence of many metabolic routes and parallel reactions which are important for the life of the bacteria. Microbiological oxidation of a mineral substrate is influenced by its own inicial concentration: This influence can be determined by means of a kinetic study. In a medium with sufficient concentration of nutrients (nitrogen, phosphorous and potassium) and an adequate supply of 0, and CO2, as the only & L source of carbon for the biochemical synthesis, the substrate concentration would remain the only limitation in the rate of leaching. In this case the Michaelis-Menten model could be applied (6). The model is based on an association of the enzyme (El with the substrate (S) with consequent decomposition of the latter into enzyme and products [ ] The rate of dissolution is defined by the equation : [ ] Were V is the rate of metal extraction (mg 1-1 1 h-1 ) ; S is the pulp density Mn is the maximum rate for metal extraction (mg 1-1 h-1) and K is the constant of Michaelis (concentration of substrate that yields Vm/2). This method is applicable only when the rate of bacterial growth is similar to the rate of metal extraction. It would therefore be sufficient to control the concentration of metal in the medium over the period of time. In the present work a systematic study of the kinetics of ZnS and CuFeS bioleaching in sphalerite and complex ore concengrates was carried out. The rate of dissolution of the Zn and Cu as function of the pulp density and temperature was determined. However, most oxidations of sulphide dissolution take place with a very slow kinetic; but, this can be accelerated considerably by the addition to the solution of suitable catalytic ions, as was Suggested many years ago by Bjorling (7). Such ions can exercise an important influence on the rate of the oxidation-reduction reactions, both homogenous and heterogenous, which take place during the leaching of sulphides; they also affect the nature of the reaction products. The action of catalytic ions has been fully developed in aqueous systems, but in the absence of bacteria (8 - 11) although the actual machanisms is not totally known. The mechanisms proposed as hypotheses in the literature (8) indicate that, in the case of ZnS, the catalyst ion act through an electrochemical mechanism according to the reactions: [ ]

Jan 1, 1989

By W. M. Ma, W. L. Zhong, Syd S. Peng

In a longwall section that consisted of 7 longwall panels, there were two high pressure gas transmission pipelines across the panels burying from 3 to 10 ft. below the surface. One pipeline was 20 in. in diameter while the other was 24 in. in diameter. In order to investigate the stress conditions sustained by the pipelines during underground longwall mining, strain gages were mounted on the pipelines above panel #3, #4, and #5. Survey monuments were also installed along but near the pipelines. This paper presents a subsidence prediction method and the preliminary results of the pipelines' stress conditions as affected by underground longwall mining.

Jan 1, 1986

By I. Iwasaki

There are many reasons why the US mineral and primary metals industry is in its present state. Undoubtedly, a flood of imported goods in all sectors is playing a major role in the plight of our raw materials industry. Domestic industry is becoming increasingly aware of the importance of its international competitiveness. And we are beginning to wonder what is happening to our technological edge. A number of factors affect the international competitiveness. Engineers cannot do much about some of these factors - labor costs, tax policy, government relations, interest rates, dollar strength, and labor-management relations. Something can be done about technology, however. Some say technology is so easily transferable today. But I would like to believe that we have the ability to apply it better than others. Not too many years ago, "made in Japan" meant cheap and shoddy products. Today, Japan has completely changed its image. The US is beginning to feel the threat from Japan's low-cost, defect-free products with dependable delivery. With worldwide recession and the strength of the dollar, we were shocked at the sudden weakness that developed in America's industries, not only in the international market, but domestically as well. What went wrong and what can we do about it? Senior executives from 300 large American manufacturing companies were surveyed. These executives believe US companies must: • invest in more efficient plants and equipment (27%); • invest in more research and development (23%); • improve the quality of service to customers (23%); and • adopt more aggressive marketing tactics and strategies (14%). Are we not doing enough research? The US has nearly four times as many people engaged in research and spends four times as much for research as Japan (Fig. 1). There is little doubt about the excellence of the US performance in basic science as indicated by the number of Nobel prize recipients. Japan has produced only four winners since World War II. Look at technology trade of five countries (Fig. 2). Again, US performance has been remarkable. An interesting observation here, is that the United Kingdom, another country with economic woes, is also in the black, West Germany and Japan, both with trade surpluses, are net technology importers. It is apparent that the US' performance in the commercialization of new knowledge is much more in question. Japan had $50 billion of trade surpluses with the US last year, which led to some friction between Washington, DC and Tokyo. Comparing the technology trade of Japan and the US in more detail, Japan imports disproportionately large amounts of technology from the US and Europe. This data is rather old, 1978, but the general trend is not too different even today. It is generally believed that scientific research leads to innovative technology, then to economic payoff. But, after seeing the current technological challenge by Japan, we are forced to change this traditional view. Investment in research may eventually lead to economic payoff, but not directly. There is a middle ground between new knowledge and its commercialization. This is an area where the Japanese have been successful. Until the 1970s, many western companies licensed patents to Japan for quick profits. But, in recent years, these companies have become more discrete about the terms of technological transfer. As a result, a number of scientists and engineers are expressing deep concern over the future of technological developments in Japan. A survey was conducted on 450 research managers of private industries in Japan on how they viewed the level of breakthroughtype original research in Japan as

Jan 6, 1986

By Robert A. Bauer

Geology and weather effects produce natural ground movements that may be misinterpreted as mine subsidence. Weather, local geology and vegetation clearly influence the elevation of the ground surface through frost action and changes in groundwater levels and soil moisture content. Common practices of monument and benchmark design and placement do not address the problem of natural ground movements. Monuments can be designed to minimize some natural ground movements. Differential displacements can be reduced by knowledgeable placement of benchmarks and monuments which are of similar design and construction. Commonly, the threshold values of movement for the determination of mine-induced subsidence are dependent on the closure errors (accuracy) of individual surveys. Accuracy is more than the amount of closure error; it should include the range of elevation changes (error band) determined for each monument over a period of time before it is disturbed by mining. Multiple baseline surveys of the entire monitoring system, conducted before the onset of subsidence, should be used to establish subsidence detection limits.

Jan 1, 1986

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material's flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982