Search Documents

By W. Randall, Robert M. Leary

Twin 1250 m (4100 ft.) long highway tunnels through Cumberland Mountain near Middlesboro, Kentucky are planned to be completed in the early 1990's. The tunnels will be excavated in sandstones, limestones, and shales, dipping at 35 to 50 degrees and striking nearly perpendicular to the tunnel alignment. In 1985-86 a pilot tunnel was excavated as a crown drift along the alignment of the southbound tunnel. The benefits of the pilot tunnel in reducing uncertainties for main tunnel construction are discussed. The cost-benefits of the pilot tunnel are examined in view of estimated main tunnel costs.

Jan 1, 1987

By Warren E. Morrison

The expansion of the United States economy in the postwar period has had a tremendous impact on the demand for energy. Not only has total energy consumption increased at an unprecedented rate, but there have been major shifts in the composition or mix of energy resources within the end-use sectors. Because of the numerous interrelationships between substitutable energy resources and their markets, the energy economy can only be analyzed in terms of the trends of its component parts. This problem takes on additional complexity when attempting to chart the nation's future energy requirements. Total energy consumption can be forecast with reasonable accuracy for periods up to 15 years by relating this to projections of economic indicators. However, forecasting the component parts of the energy economy constitutes a dilemma in that the sum of the projected parts frequently exceeds predictions for total energy. Areas of uncertainty in energy forecasting tend to mount rapidly when proceeding from total energy to the consideration of specific energy resources consumed as fuel, power, or raw materials.

Jan 1, 1965

By George A. Roche

Since our firm was established by Mr. Price in 1937, we have followed an investment philosophy which is based on the belief that investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria that we use to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of our investment strategy for two of the three mutual funds sponsored by the Price organization and for our private clients. However, during the past 5 years we have seen inflation accelerate due to a variety of factors including the inability of our government to meet seemingly unlimited needs with limited revenue sources. While there might be temporary periods of price stability, we believe that inflation will still continue to be the investor's greatest problem in future years. Our conviction that inflation would increase combined with the acceleration of inflation in the late 1960s stimulated an intensive investment research effort, on our part, to identify those companies with strong natural resource bases -- who own or control large, secure, and low cost tangible assets. Over the longer term and in an environment of a depreciating dollar some of these firms should be able to develop and sell these assets at higher prices. While we still believe that investing in growth companies is a sound investment strategy to offset inflation, we also believe that certain natural resource companies will show well above average investment performance. In the newest Price mutual fund, The Rowe Price New Era Fund, we have, as a matter of policy, placed a large portion of the portfolio in natural resource companies.

Jan 1, 1972

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By Pier Francesco Paglini, Gian Luca Menchini, Pier Francesco Boschi

"PROJECTThe “Caltanissetta” Tunnel is part of the ANAS S.p.A (National Autonomous Roads Corporation) $ 1.3 Billion Highway 640 Caltanissetta-Agrigento (Sicily, Italy) Rehabilitation Project, consisting in upgrading of 62 km (40 miles) of highway. The Italian multinational construction company Cooperativa Muratori & Cementisti di Ravenna, is the General Contractor for the design and build contract. The highway S.S. 640 starts from Porto Empedocle, to the intersection with the Motorway A 19 Catania-Palermo.The entire project, double carriageway designed for speed 70-120 km/h and maximum longitudinal slope of 4.2%, is divided into two sections. First Section: just finished and opened to traffic. Second Section: mainly involving the province of Caltanissetta, length about 28 km (18 miles), works started in 2013. This second section includes the most challenging work of all the project, the “Caltanissetta” tunnel consisting of two separate tubes, each with 3.9 km length and inside diameter of 13.50 m, in order to host 2 traffic lines and an emergency line. HORIZONTAL AND VERTICAL ALIGNMENT - GEOLOGY AND HYDROGEOLOGYThe plan alignment of “Caltanissetta” tunnel is formed by two tubes which are located at a minimum mutual distance of 22 m to a maximum of 63 m, with n. 9 pedestrian and n. 4 road cross passages; ventilation shafts are not provided. Overburden over portals area is about 5 m till a maximum of 120 m. Tunnel sections have variable longitudinal slope from 2.6% to 0.5%, transversal slope of about 3.5%. Right tube length is 3,992 m, left tube length is 3,877 m."

Jan 1, 2016

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., under contract to the Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1986

When overburden depth exceeds economical recovery in openpit coal mines, the use of highwall mining systems has increasingly come into play. However, stability in the highwalls is always a major safety concern during such mining. The U.S. Mine Safety and Health Administration requires that highwall mining operators follow ground control plans that specify the pillar sizes necessary to prevent collapse that would threaten highwall stability.

Jan 1, 2006

By Robert G. Woolery

Union Carbide_ began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.040% U308 were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leach project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on-site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. They were most generous in allowing us to visit their site, answering our questions, and were helpful in discussing the problems associated with heap leaching. They confirmed our belief that, it was possible to operate a heap leach profitably on material too low grade for. conventional milling. Based largely on what we had learned from Western Nuclear's experience, a program was set up involving a laboratory study to determine the characteristics of the mineral stockpiles as related to heap leaching and to conduct a pilot heap leach adjoining our Gas Hills mill. Basically, the pilot heap construction and leach procedure were similar to those described in the literature(1,2) with certain modifications to permit detailed monitoring of the operation. In May, '1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the follow¬ing reasons:

Jan 1, 1977

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 1, 2009

By Jens Classen, Martino Gatti

"GENERAL PROJECT DATAThe Sparvo Tunnel is part of the “Variante di Valico” project, a new 65km (40mi) highway link between Bologna and Florence, designed to renew the existing A1 route which connects Bologna and Florence. It is composed of 2 x 2,5km (1,55mi) twin tunnels excavated inside a complex geological context, characterized by the presence of a series of surface landslides and methane gas.The inclination is 2,6 % and the minimum radius is 1.400m (4.600ft). The two tunnel tubes were excavated by a 15,6m (51ft) diameter EPB-TBM from summer 2011 to summer 2013. The internal diameter of the concrete lining is 13,6m (44,5ft), made up of precast concrete segments 2m (6,5ft) long and 70cm (28”) thick, being the largest and heaviest segments ever produced. Excavation went smooth apart from initial problems concerning clogging problems and a main bearing damage of the TBM, which are discussed in a further paper during the congress. No structural damage was observed until the end of the TBM drives.SITE OBSERVATIONS DURING THE POST-EXCAVATION PHASEThe first evidence of the stress state of the segmental lining appeared on November 20, 2013 inside the northern tube (1st drive). Ring No. 884 showed obvious signs of overstress, resulting in spalling and crushing of the concrete, and the subsequent bending of the reinforcement, as visible in figure 1.At this time the tunnel invert was already partially backfilled, and construction traffic was running through the tunnel. First safety measures included closing of the tunnel, and initial measurements of the displacements."

Jan 1, 2016

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

By E. A. Barrett, L. L. Rethi

Throughout all segments of the United States mining industry, 163 independent contractor employees were fatally injured between 1990 and 1997. Factors that contributed to these injuries were identified after reviewing descriptive information contained in Mine Safety and Health Administration fatality reports for each of the incidents. Thirty-three unique contributing factors were identified and multiple factors were noted for each fatality. Those most frequently discerned were "failure to follow `standard operating procedures"', (35% of the fatalities), "poor positioning of employee" (26% of the fatalities) and "failure to maintain equipment" (23% of the fatalities). Contributing factors were then associated with the accident and job classifications of the victims. Factors having the highest frequencies in the top five accident classifications where most fatalities occurred were as follows: powered haulage - "failure to maintain equipment"; machinery - "poor positioning of employee"; slip/fall of person - "inadequate fall protection" and "failure to wear safety line"; electrical - "equipment contact with power line"; and falling/rolling/sliding rock - "poor positioning of employee. " Among the job classifications in which most fatalities occurred, leading contributing factors were as follows: truck driver - "failure to follow standard operating procedures" and "poor positioning of employee"; laborer/utility man/pumper - "poor positioning of employee"; mechanic/ repairman and welder - "failure to follow standard operating procedures." Recommendations for utilizing contributing factor information as a basis for safety training are proposed. Training programs may be developed that inform independent contractor employees of factors which, in the past, have contributed to fatal injuries in their job classifications. Then, by combining this information with contributing factors identified in "related" accident classifications, a truly focused training intervention that addresses very specific workplace hazards may he developed.

Jan 1, 2002

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By Bryan Ulrich

Knight Piésold and Co. hosted its annual roundtable discussion on March 17, 2011 at the Stockman Hotel and Casino in Elko, NV. The theme for Roundtable 2011 was, ?High density tailings, paste, and filtered tailings,? although the topic may well have been subtitled, ?Don?t prematurely rule out any technologies before they are given their day in court.? Bryan Ulrich, Knight Piésold?s local representative, as well as Tom Kerr from Knight Piésold?s office in Denver, CO, were on hand to help facilitate the discussion. Ulrich and Kerr are senior vice president and president of Knight Piésold?s U.S. practice, respectively. The event played host to more than 30 attendees from several western states. Attendees included personnel from a dozen mining properties and various corporate offices. There were also attendees from manufacturing and specialist consulting firms who have been providing services to various high-density tailings, paste and filtered tailings operations worldwide. It may be noted that the term ?filtered tailings? is used in this discussion. Alternative terms, such as ?dry stack? or ?dewatered tailings,? should be avoided whenever possible, as such terms tend to give a false sense about the nature of the material since these materials typically still retain a significant amount of moisture.

Jan 1, 2011

By Robert Rautenberg, Paul McDermott

This paper will discuss the construction of 15.9 km (9.88 mi) of tunnels on a project in Chicago, Illinois. The tunnels were driven utilizing two rock and four soft ground TBMs ranging in sizes from 7.39 m (24.25 ft) in rock down to 1.95 m (77 in) in soft ground. In addition to the mining, there are 63 upper level structures and 16 dropshafts averaging 61.5 m (202 ft) deep included on this project. Many diverse mining, excavation, support and lining techniques were employed on this project.

Jan 1, 1997

By Joseph Irons, David Westfall

Three rock tunnel sewer systems are underway in the Chicago Area. (Figure 1) The three are designed to act independently and to be later connected to the future tunnels of the master plan. The tunnel excavation for each of the systems has been completed. One is in the Northwest area within the City being built by the City, known as the Lawrence Ave. System. Another is in the Southwest suburbs, known as the LaGrange-Brookfield Sewer or Southwest 13A, being built by the Sanitary District, the third is in the South suburbs called the Crawford Avenue sewer or Calumet 18-E, Ext. A- being built as a joint venture between the City and the District. The three are similar in that they have the same purpose, the same component parts and their tunnels were constructed in the nigaran limestone using a mechanical mining machine. The purpose of each of the systems is two-fold. First to provide flood relief for existing inadequate sewer systems, and second to reduce the pollution load to the waterways caused by combined sewer overflows. The existing systems in the areas to be relieved are combined sewers built many years ago. The main outlet for the Village of LaGrange, for example, was built in 1908, is badly in need of repair and lacks the capacity to handle the flood flow from the heavily urbanized area it now serves. The dry weather flow from the area is taken off by intercepting sewers. However during

Jan 1, 1997