Search Documents

By H. Cho, P. T. Luckie

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal macerals could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation was dependent upon the comminution history. Even for the same fineness, the extent of liberation might not be the same depending on how the material was generated. The liberation of coal macerals was analyzed by examining the liberation index. It was seen that, although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinite), these particles were less liberated than coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1999

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

By Xia Guangxiang, R. Y. Wan, Yang Hanlin, M. C. Fuerstenau

The mechanism and kinetics of pretreatment on pyritic gold concentrate with the catalytic oxidation acid leach (COAL) process were studied in the temperature range of 80-100°C and oxygen pressure range of 230-1013 kPa, with sodium lignosulfonate (SL) and mixed medium of sulfuric acid (11 g/[ ]) and nitric acid (5.5 g/ [ ]). The results show that nitric acid acts as a catalyst, the surfactant changes the hydro-phobicity of resulting elemental sulfur to favor the oxidation of pyrite, and the oxidation-determining step would be the chemical reaction between nitric acid and pyrite. When about 80% of pyrite contained in the concentrate is oxidized, the gold cyanidation extraction exceeds 95 % . The nitric acid in solution can be recycled and used again.

Jan 1, 1993

Coal that meets customer specifications is often stored in silos prior to being loaded into railcars. However, it is often found that, after loading, the coal contained in a particular car does not meet customer specifications. This can occur because of the variability inherent in the coal and because of segregation, mixing and flow inside the silo. Some contracts now require the coal in each car to be within specification. Silo flow models are used to predict quality in such cases. However, developing an accurate silo flow model for each case is difficult and time consuming. This paper examines the viability of using an online analyzer in conjunction with a feedback circuit to optimize the quality of the coal being loaded into trains, so that each car meets the quality specifications.

Jan 1, 2002

By B. K. Cantrell, K. L. Rubow

The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8- µm aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 µm diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.

Jan 1, 1992

By Raymond S. Shrode

Limestone and dolomite production is of significant importance to the Baltimore and Ohio Railroad. Except for coal, more tons of limestone and dolomite are moved by the Railroad than any other mineral raw material. In the territory served by the Railroad, these materials are produced from every geologic system from Cambrian through Pennsylvanian. Some of the operations produce premium stone acceptable for high-specification steel and chemical use; at others, the stone finds application as aggregate materials and for cement manufacture. The Railroad is interested in seeing continued production from the operations it now serves, and in serving operations in a way mutually beneficial to the Railroad and to the producer. In working with producers, the importance of geologic knowledge in prospecting and development of deposits has been clearly recognized. In turn, knowledge of the economic and technological facets of production and consumption is needed for the geologists to participate with maximum efficiency.

Jan 1, 1966

By Robert J. Wise, Mark Alspaugh

Underground longwall coal mines depend on conveyor haulage to transport large volumes of coal from the longwall face conveyor to the mine portal. In the last few years, the need for longer and larger longwall panel conveyors has become very significant. In order to keep conveyor equipment to a minimum and still transport higher tonnages over longer lengths, intermediate drive technology has been developed. The use of DC motors and controls in conjunction with load sharing techniques have a1 so proven effective. A case study of a new longwall panel conveyor at Utah Fuel's Skyline Mine incorporating these design techniques will be presented.

Jan 1, 1993

By James Lonergan

This paper describes the application of the Graphics Assisted Under Ground Engineering (GAUGE) software to a 2-layered room and pillar hard rock mine. The graphics- assisted mine modeling and mine planning capabilities of GAUGE are demonstrated. The system uses polygons to model the room and pillar mine design and displays the model in plan view on the graphics screen,. The planning engineer interactively specifies areas to be mined in the medium or long term. The system calculates and accumulates tonnages and grades for the user-specified areas based on the layer being mined and the particular unit operation (drifting, widening or benching).

Jan 1, 1989

By S. C. Brown, R. C. G. Oliveira

Surface wettability, or contact angle, dictates a number of multiphase ensemble interactions that influence particulate dispersability and adhesion behavior (e.g., filler compatibility] in addition to a number of other phenomena including biocompatibility and bulk powder segregation. The wettability of particulate surfaces significantly impacts nearly all process industries; however, the available techniques to access this quantity are either relative, or tedious-and are application or industry specific. In this study, key features of existing techniques have been combined to design an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By M. Gaft, G. Panczer, R. Reisfeld, L. Nagli

Laser-induced luminescence and breakdown spectroscopy methods appear to be a good tool for real-time evaluation of dolomite content on moving belt. The distinctive feature for time- resolved luminescence is Dy3+ emission in apatite, which is excited by 251 nm laser light and detected with delay time of 5 ms and gate width of 1 ms. The distinctive features for breakdown spectroscopy are 604 nm line of F and P in apatite and 518 nm line of Mg in dolomite. The representative sampling of more than 200 pebbles has been studied by both methods. By luminescence method 100% of dolomite will be identified, while approximately 15-20% of apatite with extremely week Dy3+ luminescence may be mistakenly counted as dolomite. By breakdown spectroscopy the identification is 100% correct both for dolomite and for apatite.

Jan 1, 2002

By Robert J. Watters, Peter C. Kelsall, Joseph G. Franzone

Two separate studies investigated the compressive strength of basic igneous rocks and its relation to index properties such as porosity, density and soundrave velocity. The rocks tested were weathered dolerite from S. W. England and vesicular lavas from California. In both cases strength was affected considerably by porosity. In the dolerite, strength was also affected by fissures (microcracks) which were formed in the parent rock by shearing and later accentuated by weathering. While test results show that porosity, density and sound velocity are not reliable indices of rock strength, these properties are useful in interpretation of strength test results. Index testing can be used to classify samples according to similar behavior and to recognize the influence of fissures.

Jan 1, 1986

By Jerzy Matuszewski

Under conditions of high methane content in the seams and the descending of exploitation to greater depths, methane hazard control is becoming more and more difficult. This is due both to the amount of methane released and to the technical possibilities of diluting and capturing it. The removal of excess methane from mine workings only by means of the ventilating current has become a problem. Therefore many countries designate large sums of money for research work in the field of controlling dangerous methane accumulations and for introducing this control into mining practice. In Poland the Central Mining Institute is leading in this field. Its Safety-in-Mines Institute, Barbara Experimental Mine in cooperation with collieries has recently carried out interesting investigations on the distribution of methane concentrations in gobs behind the front of longwalls mined with caving.

Jan 1, 1980

By J. E. Hoffman, T. J. Keefe, Michael E. Stout, O&apos

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By Steven J. Schatzel

A study was made of frictional ignitions in the underground coal mining industry from 1980 to 1992. The population of frictional ignitions was correlated to a variety of potential contributing factors including the mined coalbed, geographic location, mine production, methane gas emissions, and the type of mining equipment in use. The number of frictional ignitions reported in 1991 and 1992 surpassed the annual totals in all previous years included in the study. Most frictional ignitions occur during cutting operations at a coal face by a continuous miner. The average coal production of mines experiencing frictional ignitions is greater than the average of all underground coal mines throughout the survey period. Methane drainage may have produced a drop in the ratio of gas emissions to coal production (E/P) in mines experiencing frictional ignitions.

Jan 1, 1995

By Jan Leja

Surfaces of metal sulfides react readily with selected constituents of environment. Two types of reaction products may form: (1) primary, chemisorbed and hydrophobic surface products or primary hydrophilic surface products, and (2) secondary reaction products -- produced during continued oxidation-reduction processes. For flotation, the chemisorbed surface product and the secondary reaction products, elemental sulfur or metal xanthates, must provide sufficient hydrophobicity of the surface to ensure particle-bubble attachment.

Jan 1, 1986

By Rudrajit Mitra, Wesley B. Johnson, Erik C. Westman

The ability to understand stress redistribution within a mine allows greater extraction efficiency with reduced safety concerns. Stress redistribution has been examined at the laboratory scale using ultrasonic tomography and numerical modeling using PFC3D. A data acquisition system was built to obtain tomograms as samples are loaded in uniaxial compression. Limestone samples were loaded to failure. Three-dimensional tomograms of the samples correlate to various stress distributions. The tomograms are compared to analytical and PFC3D results.

Jan 1, 2005

By Xiangze Shu, Yuzhong Xing

All programs used to optimize main fan nowdays have to be run on the large and medium- sized computers. With a lot of array elements, complex processes, low convergence speed and large storage, these programs are both time consuming and difficult to be used in the micro computer. This program uses two languages (dBASEIII and BASICA) to calculate the network and to choose the fan respectively. It allows user to compare and choose the parameters of various kinds of fan and to transfer the selected fan parameters to the master program by a data communication system. Then the user can get the air quantity, the air pressure, the power and the efficiency of the main fan. The advantages of this program arc as follows: 1. It can be run on IBM-PC or compatible micro computer. 2. It can select a fan more quickly and less time consumingly. 3. It can choose desired one or a set of fans according to user's requirements. 4. It is suitable for the research institutions and coal mines.

Jan 1, 1991

By Edward C. Dowling

Cleveland Cliffs and affiliated companies have established a commitment to the development and use of integrated process control. Substantial capital investments in process control, coupled with the dedication of human resources to effectively use the information, have generated meaningful business results. Improvements in productivity, operating costs and product quality have been realized. This paper presents an overall process control and information strategy, specific case studies, lessons learned and the current view of the next steps in the continued journey toward integrated process control and information management.

Jan 1, 2000