Search Documents

By W. Luyken, E. Bierbrauer

A number of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing. These publications demonstrate both the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. Graphical Analysis of Ore-dressing Processes The following is from Truscott's Text Book of Ore Dressing (London, 1923): x = assay of ore treated (feed). y = assay value of the concentrate. 2 = assay value of the tailing. a = weight of feed. 6 = weight of concentrate. c = weight of tailing. C = fractional concentration = = . a y - z K = ratio of concentration = 1/c a/b = y-z/x-z 2 B = fractional recovery = 9 = C y/x (3) 100R = percentage recovery. Copt. = theoretically best concentration. 100 — Copt = waste in the feed.

Jan 1, 1930

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By F. J. Smit, S. C. Sun

Flotation variables were investigated for the re-clamation of phosphate from a Florida washer slime. Under optimum conditions, 92% of the phosphate was recovered. Further cleaning of the rougher flotation concentrate resulted in a product containing about 30% P2O5 with a phosphate recovery of 65%. The enormous amount of slimes rejected in the Florida pebble phosphate fields, containing roughly one-third of the phosphate in the pebble matrix,1 has long been considered as a serious problem to the industry. The mere disposal of these slimes has posed an almost insurmountable task for several investigators.2-5 Some companies still resort to huge surface dams, some covering 1800 acres, for slime disposal.6 Information on the recovery of fine phosphate from these slimes is scanty. Dry separation8 and electrostatic beneficiation8 were suggested, but would necessitate radical changes in the present mining and concentration methods. Haseman10 proposed the selective flocculation of colloidal phosphate with starch, while Ralston11 suggested the removal of clay from the matrix by amine flotation. Leaching of the slimes for recovering the small amount of uranium was attempted by the Battelle Memorial Institute12,13 but proved to be economically unfeasible. The purpose of the present investigation was to determine the optimum fatty-acid flotation conditions for reclaiming the phosphate discarded with the Bartow washer slime. Prior to the flotation experimerits, however, the size distribution and the minera-logical composition of the employed slime had to be determined.

Jan 1, 1963

By W. P. Sykes

ThiS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Mlolybdenutn (m.p. 2500" C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; Chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450" C. and an allotropic change at about 370" C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per ccnt. iron. Aluminum is one of the low melting-point metals. Some tensile tests at clevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available rccommendcd this metal. The samples marked A1 arc an aluminum-copper alloy that contains 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat coniplicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400" C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate the temperature. Hot oil was uscd as the heating bath for drawing the

Jan 1, 1921

"The method of conveying ore from the ore-pocket at the shaft collar to the railroad ore bins, whence it is transported to the reduction works, is by cars with electric haulage.The cut shows the car coupled to the electric locomotive at the moment of dumping into the railroad ore bins.The locomotives used are of several makes, usually having two 12 ½ h-p. motors of a rated draw-bar pull of about 1,200 lbs., using 500 volts D. C. Track gauge is 30 inches, and speed is six miles per hour.The car holds two skip loads-10 tons—and has sides opening outwards the full length of the car, for rapid side-dumping. One man operates car and motor, and loads and unloads the car. The trolley pole runs in both directions without reversing.Loading is clone by operating a valve connected to a compressed air lift, which raises and lowers a gate in the ore-pocket chute, the ore running by gravity into the ore car spotted under the gate of the chute. Dogs hold the sides of the car in place at the bottom, the tops of the sides being hinged, and a hand lever releases the dogs, permitting the sides by the pressure of the ore against them to open at the bottom.With little manual effort one man does the work which was formerly done, when hoisting ore with cars and cage, by 10 men under laborious conditions."

Jan 1, 1913

By M. Bourgon

The conductivity of liquid copper sulfide has been measured as a function of the mole fraction of sulfur in the melt at three temperatures: 1170°, 1250°, and 1300°C. The results show that a) the conductivity of copper-rich Cu,S is independent of the sulfur pressure in the furnace, and b) the conductivity of sulfur-rich copper sulfide increases rapidly with sulfur pressure. Assuming that the band theory is applicable to liquids leads to the conclusion that copper-rich copper sulfide is an intrinsic semiconductor, in which case electrons act as carriers. The activation energy for conduction in this case has been calculated to be 0.7 ev. On the other hand, sulfur-rich copper sulfide behaves as a p-type semiconductor, positive holes being responsible for conduction. IN order to elucidate the structure of Liquid copper (1) sulfide, Derge, Pound, and Osuchl have studied the electrical conductivity of this compound as a function of temperature. Their results showed that the conductivity is rather high, of the order of 100 ohm" cm", and that the temperature coefficient of conductivity is positive. This high conductivity seemed to indicate electronic rather than ionic conduction. This conclusion was checked further by Derge, Pound, and Yang,2 who measured the current efficiencies of copper sulfide melts at various temperatures. In all cases, the current efficiency was found to be nil, indicating the absence of appreciable ionic contribution to the conduction in

Jan 1, 1958

By Phillip O. Tyree, Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducing bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the pores of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also expanded reserves in a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore occurrences. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of June 1, 1984, a total of 29.87 million mt (29.4 million long tons) of sulphur had been produced west of the Pecos River. Duval Corporation has produced more than 88 percent of that total.

Jan 1, 1985

By L. D. Hall, S. J. Rothman

DIFFUSION coefficients of RaD (PD) and RaE (Bi) in a Bi-0.255 atomic pct Pb alloy have been measured by the methods outlined in a previous paper.' The following changes were made in the experimental procedures: the bath was made up of about 400 to 500 g Bi; and no correction was made for the volume change of bismuth on melting. The data are presented in Table I and Fig. 1. A least-squares analysis of the data yielded D = (0.120 t 0.09) exp ( -9680 + 1070/RT) D- (0.0465 0.001) exp (-8100 + 466/RT). Statistical analysis of the data indicated that the activation energies are significantly different at the 50 pct level, but not at the 75 pct level, while the D values are significantly different at the 97.5 pct level, but not at the 99 pct level. The differences are thus not as clear-cut as they were for lead. However, bismuth diffuses faster than lead in high bismuth alloys as well as in lead. The high activation energies, more than twice the value calculated from viscosities, are in good agreement with the results of Grace and Derge.' No data were obtained at higher temperatures because of gas bubble formation in the capillary. Acknowledgments This work was supported by the Office of Ordinance Research under contract DA-04-200-ORD-178. The authors thank 0. P. Vieria and M. Volpe for help in the experimental work.

Jan 1, 1957

By R. R. Boucher, O. J. C. Runnalls

A pronounced thermal effect has been observed on heating or cooling a1wninum-rich Al-U and Al-Pu alloys. From microscopic and X-ray diffractionstudies, the effectl has been attributed to trnsfor)nations in the inlemetallic phases UAl, and PuAl , involuing rearrangement or cluslering of vacancies The transformation obsrved in Al-20 wi oct U alloys occurred near the a Al-UAl4 eutectic tem-perature of 646°C making it difjicult to detect from heating curves. When cooling, howeoer, thermal mad X-ray analyses indicnted that the high-temperati~re phase labeled p UAL, precipitated initially during euitectic solidification. As solidification continued and after an induction period o-f 5 lo 20 tnin the nu-cleatiorz and growth of the low- twmperature phase, a UAl4 produced an euolution of energy which raised the observed alloy temperature by 1° to 2°C. in Al-Pu alloys the transformation occurred at 645°C, 5 deg below the eutectic solidification temperccture. The eslimated latent heat of transformation was 25 +5 cnl per g PuAl,. The high-tetnpevcl-ture forms of UAl, and PuAl, were easily 9-etccined by chill casting Al-U and Al-Pu alloys and on reheating the alloys the trcltzsforrnation to the a phase was sluggish even above 600°C. Separated single cryslals o-f UAl4, joy example, showed no evidence Of transformalion after heating for 16 hr at 620°C. The transformation rates increased yapidly enough with increasing temperature, however, that a a spontaneous liberation of energy lens observed on occasion when bealing cast Al-20 wt pet U to neal- the RECENT phase studies on A1-Pu alloys have indicated that earlier reported equilibrium diagrams should be modified to take account of several poly- morphic transformations in the intermetallic compound PuAl,.' During the course of the latter work an unexpected heat evolution was observed while cooling a solid alloy consisting of a mixture of a aluminum and PuA1,. The evolution occurred at 645°C, y below the a A1-Pu A1, eutectic solidification temperature. Subsequent thermal-analysis experiments with A1-U alloys showed that heat was evolved there also at a temperature nearly coincident with the a A1-UA1, eutectic solidification temperature of 646°. A search of the literature revealed that similar thermal effects had been observed before for both A1-U and A1-Pu but had never been fully explained.2,3 The purpose of the present paper is to describe thermal-analysis and X-ray diffraction experiments which have led to the conclusion that the thermal effects are due to transformations which involve the rearrangement of vacancies in the intermetallic compounds UA1, and PuA1,. EXPERIMENTAL PROCEDURE The A1-U alloys were prepared by heating super-pure aluminum (99.99 pct +) obtained from the Aluminum Co. of Canada in a graphite crucible surrounded by an induction coil. At 1000°C high-purity uranium metal produced by the Eldorado Mining and Refining Co., Ltd. was dropped into the liquid aluminum and was dissolved completely within 15 min. The impurities in the uranium were A1—4 ppm, Ca-4, C-70, Cr-3, Cu-6, Fe-30, Mg-2, Mn-10, Ni-25, Si-25, and Zn-2. The A1-Pu alloys were prepared by reacting plutonium dioxide with liquid aluminum under cryolite (3 NaF . AlF,) for 10 min at 1100°C in graphite crucibles exposed to the air. The plutonium was 99.8 pct pure, containing trace impurities of Ca, Cu, Fe, Pb, Si, and Zn. The liquid alloys were usually poured into water-cooled molds to provide castings of uniform composition from which samples could be cut for heat treatment and thermal-analysis experiments.

Jan 1, 1965

By J. E. Dorn, S. K. Mitra

The low -temperature tensile and creep behaviors of single crystals of copper were evaluated and analyzed in such a manner as to provide an estimate of the separate contributions of short-and long-range stress fields to strain-hardening. Furthermore, the average force-displacement diagram for thermally activated intep-section of two dislocations was estublished. This diagram plus a knowledge of the variation of dislocation spacing and the long-range back stresses with strain permits on accurate prediction of creep rates. The calculated activation energy for intersection under conditions of a constant strain rate increases linearly with the absolute tempevatus-e as required by theory. AN understanding of the detailed mechanisms for strain hardening constitutes one of the principal unsolved problems in dislocation theory. Two major models for strain hardening have been advanced in the past. The one that has received greatest attention assumes that strain hardening arises exclusively from long range interaction stresses between moving dislocations and piled-up arrays of blocked dislocations on the slip planes. This type of interaction was first announced by Taylor' who revealed that the back stress fields due to a simple uniform array of positive and negative dislocations entrapped in the deformed crystal would result in parabolic hardening. Shortly thereafter Andrade and Henderson" demonstrated that the strain hardening of fcc single crystals was not parabolic, as previously thought, and finally it was recognized that a typical stress-strain curve consisted of three successive stages of deformation, niz., the easy glide, Stage I, linear hardening, Stage 11, and the parabolic hardening, Stage 111, ranges. The objections to Taylor's somewhat na'ive model, which were presented so forcefully by cottrell; were largely removed by the more realistic details incorporated in Mott's analysis.5 But because Mott's theory for hardening via long range stress fields gave somewhat analogous results to that of Taylor's (inasmuch as it also predicted a parabolic rate of strain hardening whereas the observed rate of strain hardening in Stages I and I1 were linear), it was not widely accepted. Major consideration was therefore given to models, such as those which were advanced by Friedel and seegere that were formulated for the ad hoc purpose of yielding linear rates of strain hardening. The second major thought regarding strain hardening is based on the concept that it arises principally from short-range stress fields due to the interactions between intersecting dislocations. Cottrell and stokes7 showed, several years ago, that the constancy of the flow stress ratio at two temperatures regardless of the strain was inconsistent with the concept that strain hardening arose exclusively from long-range back stresses. The argument that strain hardening was primarily due to local interactions of intersecting dislocations was presented in considerable detail by asinski.' Extending Basinski's method of analysis of the intersection process, Mitra, Os-borne, and dorn recently demonstrated that indeed the strain hardening in aluminum single crystals arises principally from local effects coincident with intersection; however, these conclusions, too, must be modified, as will be shown later in this report. The present investigation, devoted principally to the low-temperature deformation of copper single crystals, was initiated in an attempt to ascertain whether or not the same conclusions arrived at for aluminum also apply to metals, such as copper, which have much wider stacking faults. It was soon observed that the strain hardening in copper could not be attributed exclusively to local effects between intersecting dislocations. Previously no analytical method for arriving at the possible simultaneous contributions of long-range stress fields and localized forces on intersecting dislocations was available; consequently, the separation of these two factors could not be readily accomplished. In the present report a method of estimating the separate contributions of each of these two factors to strain-hardening will be presented. The authors will show that both long-range stress fields of the type contemplated by Seeger and Friedel as well as short-range forces of the type considered by Basinski are responsible for strain hardening in fcc metals at low temperatures. This method of analysis also accounts for, in a satisfactory way, the effect of stress, temperature, and strain on the creep rate under constant stress. Furthermore, in the course of presenting their methods of analysis the authors will also reveal the rather complete agreement of their experimental data with the concepts of the theory for thermally activated intersection of dislocations. INTERSECTION MODEL As shown by seegerl0 the strain rate arising from thermally activated intersection of dislocations is given by

Jan 1, 1962

By H. R. Thresh, A. F. Crawley, D. W. G. White

The densities of liquid tin, lead, and Sn-Pb alloys have been measured over a range of temperature above the liquidus. In all cases, data can be adequately represented by an equation of the type p = a + bT. For pure tin, the values of a and b are, respectively, 7.139 and 7.125 x 10-4, and for pure lead, 11.060 and 12.220 x 10-4. At constant temperature, molar volumes in the Sn-Pb system vary linearly with composition. DURING the course of a long-term program at the Department of Energy, Mines and Resources, Ottawa, Canada, the densities of liquid tin, lead, and Pb-Sn alloys were studied. The work reported herein draws on two sets of results independently achieved by Thresh, on the one hand, and by Crawley and White, on the other. EXPERIMENT The method and apparatus were originated by Thresh and have been described in detail in Mines Branch reports.172 In operation, the 14 cu cm graphite pycnometer is put in the furnace as shown in Fig. 1 after a machined charge has been placed inside the pycnometer and the lid screwed down. The dimensions of the charge are such that, upon melting, a small excess of liquid metal is discharged through the capillary hole to displace the weighted float above. When the pycnometer has been equilibrated at the experimental temperature, the

Jan 1, 1969

[SATURDAY, FEBRUARY 16 10 am to 5 pm Council of Section' Delegates SUNDAY, FEBRUARY .17 1 pm Student Relations Committee 2 pm Board of Directors 2:30 pm MIED-Mineral Economics Instruction 5:30 pm MIED-Cocktails and Buffet Supper 7:30 pm MIED-Mineral Education 8 pm IMD-Program Committee]

Jan 1, 1952

Jan 1, 1954

Dr. Healy's paper presents a concise state-of-the-art description of mechanistic, thermodynamic models available today for design, interpretation, and trouble-shooting flocculation processes and problems. Coagulation by manipulation of inorganic electrolyte concentrations is controlled largely by adjustment of electrostatic repulsive forces, guided by well understood theory. For simple solids in simple electrolytes, existing models are capable of predicting the influence of potential determining ion and one dominant, non-reacting, symmetrical electrolyte concentration on floc stability quantitatively. Concentration changes required to coagulate and disperse can be estimated. Convenient, easily understood means are available for summarizing the effects of key variables, (e.g., pH, ionic strength) on dispersion stability, and estimating tolerance to unintentional changes (Matijevic coagulation domain diagrams). These models have not been developed to the point that mixed unsymmetrical electrolytes can be easily handled. They are capable of describing two- solid heterocoagulation, but not “n-solid” heterocoagulation. In combination with recently developed computer codes for simultaneous computation of solution equilibria, ion exchange and electrical double layer properties (1,2), these models .should be capable of describing simple clay coagulation systems. This has not been done. Models developed for polymer flocculation are valuable interpretive tools, have some qualitative predictive value, but are less potent in quantitative needs. Most real systems probably involve more than one mechanism of floc stabilization. Little has been done toward developing combined models, even in the simplest systems.

Jan 1, 1979

By Frank J. Markewicz, William Lodding

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite by the mineralogist. The word glauconite is from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was dug and marketed as a fertilizer and soil conditioner for more than 100 years. The advent of prepared fertilizers with adjustable nutrient ratios led to the decline of green- sand for agricultural application. The material has since been recognized for use in water treatment. Unfortunately, in spite of large reserves and worldwide distribution, the mineral has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This lack is probably due to a paucity of research on its potential commercial application. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and generally low potash content (up to 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of up to 100 tons per acre were sometimes made, although recommendations for agricultural use suggested 20 to 50 tons per acre (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as "poison," "burning," or "black marls." The availability of higher-grade potash salts from other mineral sources, and the manufacture of prepared fertilizers, displaced the agricultural use of green- sand during the later 1800s. During the mid-1800s the domestic greensand industry, centered in a small section of the eastern United States, grossed more than $500,000 per year. Toward the end of the century, annual production had dwindled to less than $100,000. By 1910 there were only six or eight greensand producers, grossing less than $5000 (Tyler, 1934). There was a small revival in the industry during World War I because of the curtailment of foreign potash, especially from Germany. During the later 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace- element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base-exchange properties would release trace elements. For a short time glauconite was utilized in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s for making green glass (Cook, 1868). In the early 1900s the base-exchange property of glauconite was recognized for water treatment, and the mineral gained acceptance as a water softener. Mansfield ( 1922) does not mention base-exchange; however, the base ex-

Jan 1, 1975

By J. P. Myers, A. H. Flagg, E. S. Mardock, J. L. P. Campbell, J. M. Terry

The development process for the use of radioactive tracers as a means of locating zones of permeability is discussed. The general techniques for the safe handling of radioactive materials is given as developed by the Lane-Wells Co. and Well Surveys, Inc. The prob1em and. successes with tracers in waterflood systetns, oil and gas injection profiles, fracture sand tracing, squeeze (ement tracing. lost circulution, and cement top localion are discussed and illustrated. INTRODUCTION The exact location of the permeable zones lying within the productive horizon has been a major problem faced by the petroleum engineer for decades, and it has been a problem which has seldom been solved with certainty. Reservoir engineers usually have to incorporate a question mark in their estimates of future reservoir performance because of blanks in the core data. Although the use of radioactivity or electrical logs for the estimation of porosity has been of great assistance in furnishing a record for the reservoir engineer, this application of logging data has not completely solved the problem. In short, the industry needs an in-situ well surveying method which can locate and estimate the permeability of the zones existing within a given pay section. The initial development work with radioactive tracers has been towards filling the need for permeability information. Progress to date permits the location of permeable zones with a qualitative estimate of their relative importance with respect to permeability. The calibration of the method is still incomplete. but present development work on tracer preparations, borehole effect correction factors, and instrument limitations give a promise of quantitative "permeability profiles" in the near future. The development work on the radioactive tracer method discussed here began several years ago in the laboratories of Well Surveys, Inc., in Tulsa. At the outset of this work, three approaches to the problem were visualized as follows: 1. A fluid carrying a soluble, chemically inert, gamma ray emitting isotope is pumped down the borehole and out into the permeable zones of the formation. The greater gamma activity of the permeable zones thus permits them to be differentiated from the impermeable zones which contain no active tracer. It was found difficult to obtain a tracer material which was chemically inert. Absorption to some degree was noted in all experiments. Also, it proved impossible to hold the tracer near the horehole where it could be logged. 2. A fluid carrying a soluble, gamma ray emitting isotope is pumped down the borehole into the permeable formations. In contrast with proposal 1, above. the tracer is chemically active with the fluids and materials in the pore spaces of the permeable zones. The permeable zones are thus indicated by their higher radioactivity level. The main difficulty in this proposal was finding a tracer material which would not be absorbed by shale as well as in the permeable porosity. Very little field work was done with this system. 3. Radioactive particles suspended within the injection fluid are pumped down the well. As the fluid enters the permeable formations, the radioactive particles are filtered out on borehole wall. The permeable zones are differentiated from the impermeable by the gamma ray activity deposited on the formation wall.

Jan 1, 1956

By R. M. Douthwaite, G. Birkbeck

The effect of grain size and specimen dimensions on the occurrence and magnitude of a yield point drop in pure iron has been examined. The tests were done at room temperature. The results indicate that gain size is the critical factor determining whether a yield drop occurs. The specimen diameter:gain size ratio does not influence the magnitude of the yield drop for the range of gain size and specimen diameters investigated. HUTCHINSON,' petchY2 and worthington3 have investigated the grain size dependence of the upper yield stress (uUYP) and the yield point drop, ouyp - aLYP, in Armco iron, mild steel, and Si-Fe, respectively. These authors used center-annealed wires to avoid stress concentration from specimen shoulders and to ensure uniformity of the applied stress. Coarsegrained specimens show no yield point drop; the yield point drop then increases as d-'I2 increases (where d is the grain diameter). These results can be understood in terms of Petch's analysis2 in which the magnitude of amp depends on the strain rate in the (limited) number of grains deforming plastically at the upper yield point. If N grains per unit volume are undergoing plastic deformation, the strain rate in the deforming grains is l/Nd3 times higher at the upper yield stress than when the whole specimen deforms homogeneously. If N is constant and independent of grain size at uUyp, then all the grains are deforming when ~d~ = 1, so there is no yield point drop. At finer grain sizes, the yield point drop is given by: where AU, is the friction stress increase corresponding to a tenfold strain rate increase. Christ, Smith, and Burton studied the upper yield point in 0.050-in.-diam wire specimens prepared from zone-refined iron. Each end of the 2; -in. specimens was soldered to a & -in. diam steel ball and the load applied through the two balls. There was a yield point drop in specimens with grain diameters less than 0.1 mm; no drop was observed in specimens of grain diameter greater than 0.1 mm that were free from veining substructure, but specimens of grain diameter 0.129 mm, annealed in the y range, showed an upper yield point. and this was associated with the presence of a veining substructure in these specimens. Christ et al. suggested the upper yield point occurs when more than a specific number of grains fill the specimen cross section so a multiplicity of slip is required to initiate plastic deformation. Table I summarizes the published data on the grain size at which the yield drop disappears. On the basis of this data the ratio of specimen diameter:grain diameter = 5 to 27 appears to be the critical value for the occurrence of a yield point drop. Thus, petch2 interprets the appearance and magnitude of the yield point drop in terms of the limited number of grains deforming plastically at uuyp, whereas Christ et a1. consider that the occurrence of the yield drop depends on the ratio specimen diame-ter:grain diameter. The published data cover a wide variety of materials so some variation between the results is to be expected, but the size range covered in the data of Table I is rather limited. In an attempt to discover whether the specimen diameter:grain size ratio or the grain diameter is critical in determining

Jan 1, 1969

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1939 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and ;I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron. and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which is issued quarterly. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administra-tion, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CON-TRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes. CONTRIBUTIONS and Other TECHNICAL PUBLICATIONS will be sent upon request. A member relay purchase an additional copy of a TECHNICAL PUBLICATION Or a CONTRIBUTION at One cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION Of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum; Canadian and foreign postage 50 cents extra. METALS TECHNOLOGY, $7 per annum; Canadian and foreign postage 50 cents extra (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum; Canadian and foreign postage 50 cents extra (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers). PETROLEUM TECHNOLOGY, $4 per annum; Canadian and foreign postage 50 cents extra. Bound volumes have been mailed to members that have requested them, and MINING AND METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and lie may purchase for $2.50 one copy of a volume not already received; additional copies of 'the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members; to nonmembers 50¢ current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum plus $1 for Canadian or foreign postage.

Jan 1, 1939