Search Documents

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By J. A. Pusateri, M. A. Orehoski, N. R. Arant

Plant studies on commercial-size ingots and laboratory experiments with induction furnace heats have demonstrated that the major source of ingot cracks is associated with two conditions arising during top-pouring practice: 1—solidification during pouring, and 2—turbulence created by the impact of the stream. Methods of controlling the two factors were effective in eliminating or significantly reducing ingot cracks. BECAUSE the process of removing surface defects from hot-rolled product is so costly, the steel industry is striving constantly to develop methods of preventing, or at least decreasing, the occurrence of surface defects. Investigations have revealed steel-making and processing variables related to major surface defects, and controlling these variables has led to improvements in surface quality. However, the fundamental causes of major surface defects, such as ingot cracks, have not been determined; consequently such defects persist. At the Research and Development Laboratory of the United States Steel Corp. in Pittsburgh, a seam research program was initiated to determine the fundamental causes of certain major defects. As a part of the program, ingot cracks in killed, finegrained C1020 steel were selected for study. A cost survey indicated that, of the steels produced in sizable tonnages, carbon steels in the range of 0.18 to 0.23 pct C content require the most conditioning. Since this is particularly true of C1020, any im-provement of surface quality that might be effected from the study would be beneficial. Also, since the frequency of ingot cracks is exceedingly high for this grade, the steel would provide an excellent opportunity for a thorough study of the ingot-crack-ing problem. Why steels in this carbon range tend to exhibit more ingot cracks than do other steels was not considered in the investigation; the mechanism of ingot-crack formation was of paramount importance. Also, only the top-pouring practice was considered in the investigation, because this pouring procedure is used more extensively than others. In this study, ingot cracks are defined. as deep surface defects that sometimes are observed in an ingot prior to rolling but usually are observed during the initial stages of rolling on the primary mills. These defects may occur at any angle to the rolling direction but are most prominent in the transverse or nearly transverse direction. The appearance of ingot cracks on the rolled product varies with respect to their angle of formation and with the extent of rolling after their first occurrence. Ingot cracks are also termed "deep seams," "arrowheads," "irregular cracks," and "transverse cracks." Fig. 1 shows ingot cracks in a rolled bloom. This report summarizes: l—the exploratory investigation of commercial-size ingots; 2—the labor-atory investigations related to determining the source of ingot cracks and developing corrective methods; and 3—the plant evaluations of laboratory methods of decreasing ingot cracks. Exploration of lngot Cracks in Commercial Ingots Materials and Experimental Work: At the Du-quesne Works of the United States Steel Corp., five heats of killed, fine-grained C1020 steel were selected for the exploratory phase of the seam-research program. The heats were made by open-hearth practices that are considered most conducive to good surface quality. They were top-poured into 22x25 in. big-end-up hot-topped molds. One as-cast ingot and four other ingots rolled to the following cross-sectional sizes were set aside from each heat: 16x20 in.; 9 1/2x10 in.; 5x5 in.; and 2x2 in. The processing of the heats, from the time of charging in the open hearth furnaces to the end of the rolling operation on the primary mill, was observed carefully and recorded. The cast ingot and the four rolled ingots from each heat were examined for surface defects. The cast ingots were split longitudinally near the vertical center plane to expose the ingot structure beneath badly cracked regions. Also, a series of transverse sections was cut at about 1 in. intervals in a badly cracked area of one ingot. All sections were ground, polished, examined by sulphur printing and deep etching, and photographed. The rolled ingots

Jan 1, 1955

By H. C. Goodrich

AT THE Utah Copper mine, steam shovels were first used, in 1906, for the removal of overburden, and in June, 1907 for the mining of ore. Prior to 1907, the ore came from underground development work and from stoping. The use of the steam shovel gradually increased until 1914; since then all material, both overburden and ore, has been loaded by power shovels operating on the various benches of the mine. During FIG. 1.-SCENE OF UTAH COPPER MINE BEFORE OPEN-PIT MINING WAS BEGUN. these 19 years, there has been a great improvement in open-pit mining; largely in the use of equipment having greater capacity and dependableness. The history of the development of mechanical shovels and related equipment, as affecting the Utah Copper Co., would be interesting and would justify considerable space; but of greater interest at this time is the operation of the equipment now in use. The Utah Copper mine is in a great deposit of copper-bearing monzonite, which occurs as a prominent headland of the Oquirrh range of

Jan 9, 1925

By T. E. Leontis, F. N. Rhines

THE oxide scale that forms upon magnesium at elevated temperatures is nonprotective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth1 and has been verified by Suzuki2 and by Scheil.3 Pilling and Bedworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki,2 the product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavault5 observed that excrescences form upon liquid magnesium and alloys in the course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium7and calcium8 minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.9 Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Scheil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. EXPERIMENTAL PROCEDURE AND RESULTS The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the

Jan 1, 1946

By Carl Henrich

Jan 1, 1890

By Alexander Field

The hot-rolling properties of a series of high-sulfur steels are described. From a consideration of the sulfur, manganese, and zirconium contents of these steels, it is shown that zirconium reacts with the sulfur content of molten steel in accordance with the equation Zr + 2S = ZrS2. Zirconium disulfide appears in the finished state as gray-colored inclusions, similar to manganese sulfide in plastic behavior and general appearance. Zirconium completes its act of deoxidation before proceeding to combine with sulfur and indirectly increases the effective sulfur-combining power of any manganese which may be present. IN A previous paper,1 the experimental methods used and some of the results obtained in an extensive investigation of steels containing zirconium were described. The present paper considers in greater detail one of the most interesting of these effects, namely, the elimination of "red shortness" and the occurrence in steel of a compound of zirconium and sulfur. A consideration of the actual percentages of zirconium, manganese, and sulfur in numerous steels in the light of behavior during rolling has led to new conclusions of the most practical import regarding the reciprocal relationships of these elements. The microscopic examination of high-sulfur steels containing zirconium has also been productive of interesting results. Before discussing the experimental data in question, it may be stated, briefly, that the reaction between zirconium and sulfur in molten steel may he represented by the simple equation, Zr + 2S = ZrS2, and that the zirconium sulfide thus formed occurs in the finished steel in the form of gray-colored inclusions, closely resembling manganese sulfide and, like the latter, exhibiting plasticity at rolling temperatures. Molten steel containing zirconium retains such a negligibly small amount of oxygen in solution that the foregoing reaction goes to completion.

Jan 2, 1924

By C. H. Mathewson, H. l. Burghoff

The study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and go per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrys-tallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300°, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrys-talline 70-30 brass. Previous Work Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler2 have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty and Moore." Results of the last-named investigation were published while the present work was in progress. Miller5 examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior of iron crystals under static tensile loading at room temperature was reported by Gensamer and Meh17 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of crcep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By H. l. Burghoff, C. H. Mathewson

The study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and go per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrys-tallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300°, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrys-talline 70-30 brass. Previous Work Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler2 have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty and Moore." Results of the last-named investigation were published while the present work was in progress. Miller5 examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior of iron crystals under static tensile loading at room temperature was reported by Gensamer and Meh17 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of crcep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By E. G. De Coriolis

THE development of huge production facilities and of new or improved processes for manufacturing magnesium from its raw sources has been an outstanding achievement of this war. Furthermore, at least one new method has reached a stage of pilot production that offers promise. Its potentialities seem to indicate that a reduction in cost and simplification or elimination of problems incident to the use of at least one of the present processes are quite within the realm of possibility. Although magnesium of very high purity (99.9 per cent and higher) is obtained, and the rate of recovery reasonable (60 to 70 per cent), the ferrosilicon reduction process is open to a serious objection, which at the time its use was proposed was thought to be sufficient to raise some doubts as to its success, at least on a high production basis. The temperature range at which the reaction is carried out-namely, 2100° to 2150°F.-is very close to the failure temperature of the material of which the retort is made. It is so close that for a time it was assumed it might make commercial use of the process an impossibility. However, at the time under discussion, the demand for magnesium was so great that it was felt by those who had to go ahead and produce this essential metal that the emergency warranted their taking a chance on this process. Subsequent developments have fully justified the soundness of their decision. Fortunately for the war effort, when the plants were put into operation it was discovered that although the retorts did collapse in rather short periods of time, as predicted, they could be blown back into operable shape by application of high-pressure air. This practical method of operation so relieved the situation that the problem disappeared. Nevertheless, if the process had not been successful, or the production of magnesium by the electrolytic process had not been able to keep pace with demands, our war program would have been seriously impaired. "FIRELESS COOKER" PROCESS For this reason a program was set up and assigned for the development of a new method that had been suggested to the War Production Board in 1941. It is believed justifiable in terming the method "new" for several reasons: (1) while utilizing the same (ferrosilicon) process as the Pidgeon, hence involving similar reactions, the type of retort or furnace is essentially different, (2) the method of operation, reaction temperatures, etc., differ materially, and, most important of all, (3) the problems to be overcome in making the process successful were not and could not have been anticipated by anything previously known about the Pidgeon process. As will be shown later, the briquetting process, the condenser, the furnace lining

Jan 1, 1945

By K. E. Gray, A. Podio

ABSTRACT Berea and Bandera sandstone samples were impacted with both 3/4-in. and 1/2-in. long wedges, each having a 60° included angle and a 0.05-in. flat, at various confining pressures, with borehole and pore pressures held fixed at atmospheric pressure. Samples were saturated with air, water, glycerine-water, solirol, mineral oil and soltrol-mineral oil mixtures to obtain a wide range of pore fluid viscosity. Penetration depth was held constant at 0.1 in. Dry and soltrol-mineral oil-saturated Berea samples were impacted at depths of penetration from 0.01 to 0.04 in. under 1,000 psi confining pressure to study crater initiation. Results indicate that viscosity of the pore fluid is influential primarily during the early stages of crater formation. Differences in bit force, crater volume and blow energy for tests parallel and perpendicular to bedding were significant, but decreased as the stress state was elevated. Crater volume, blow energy and bit force were nonlinearly related with depth of penetration. Crater volume was nonlinear with energy of blow. Fixed-penetration tests on saturated Berea yielded greater crater volume than did similar tests on dry samples. Differences in the nature of deformation for low values of bit penetration were noted between saturated and unsaturated samples. INTRODUCTION Rock failure during bit-tooth impact and scouring action constitutes a vital part of the drilling process and a difficult problem for researchers. Much study has been devoted to various aspects of the problem, and much has been learned about mechanics of rock failure. However, analytical treatment of drilling at depth remains difficult, partly because there are so many factors involved and because valid simulation of downhole conditions is extremely difficult. Forming individual craters by a bit tooth or chisel impacting, or indenting, a rock mass has been studied by many investigators.1-18 Similarity between single-tooth chisel impact and the corresponding action of a rotary bit has been discussed by Appl and Gatley, Garner, Podio, and Gatlin l8 compared the similarity in single-blow impact tests with microbit drilling data reported by Cunningham and Eenink.l9 Maurerll has used single-tooth impact data to develop a "perfect cleaning" theory of rotary drilling. Individual roller cutter-tooth impact data have been reported by Young. 20 Single-tooth tests in all of the cited literature were carried out on dry rocks. Inasmuch as any subsurface rock of oilfield interest is saturated with some fluid, it seemed desirable to study crater formation in permeable rocks saturated with a viscous pore fluid as a step, however short, toward more realistic simulation of subsurface conditions. This paper presents results of single-blow chisel impact studies on Berea and Bandera sandstones, both dry and saturated with pore fluids of various viscosities at confining pressures to 10,000 psi. EXPERIMENTAL APPARATUS AND PROCEDURE EXPERIMENTAL APPARATUS The same basic apparatus for single-blow chisel impact at elevated stress states, described in earlier papers was used in this study. l6. l8 Fig. 1 shows the complete experimental system; Fig. 2 shows a cross section of the pressure cell, with a sample ready to be impacted. EXPERIMENTAL PROCEDURE Two different rocks, Berea and Bandera sandstones, were used in this study. Both rocks have been used extensively in research, and rock descriptions can be found in a paper by Gnirk and Cheatham.15 Permeability to air of Berea is about 300 md normal to bedding and 540 md parallel to bedding. Bandera had vertical and horizontal air permeabilities of 18 and 57 md, respectively.

Jan 1, 1966

By N. J. Myers, S. J. Nemeth

POWER in the mill at Appalachian Sulphides Inc. is provided by 86 electrical motors ranging from 1 to 200 hp and totaling 1200 hp. After a careful study of different types of support for these cables an expanded metal trough was chosen as the most suitable. One hundred and twenty feet of trough were installed in 18-in. width and 150 ft in 6-in. width. This trough carries all the power as well as the control circuits. Now that the electrical distribution system is complete it is clear that this type of cable supporting system offers many advantages. To handle the same amount of cable in conduit, for example, would have required such a jungle that wiring all the different motors and controls would have been very difficult, even for the original hook-up. In the Appalachian Sulphides operation it has been necessary to make changes from time to time in the wiring of the different motors. These changes are readily made with the present cable supporting system because the trough leaves the wires accessible for rerouting as needed.

Jan 1, 1958

By Kyle Wightman

INTRODUCTION CRA Limited is the largest mining group in Australia by value of sales and the second largest company in Australia in terms of share market capitalisation. In the past 25 years, CRA, its predecessors and affiliates have been involved in a number of mining and further processing developments in Australia and elsewhere. Many of these have been financed using project financing techniques. These include Comalco's development of the Weipa bauxite deposits in Northern Queensland in the late 1950's, the Hamersley iron ore developments in the Pilbara region of Western Australia in the mid 1960's, the Queensland Alumina Limited alumina refinery in Gladstone, Queensland, at about the same time, and the Bougainville copper project in 1969/70. In the past three years CRA has again utilised project financing techniques to fund its Tarong steaming coal project in Queensland, the Blair Athol steaming coal project also in that State and CRA's interest in the Argyle diamond project in the Kimberley region of Western Austrlia. PROJECT FINANCE DEFINED Nevitt Definition Nevitt's is the most frequently quoted definition - "A financing of a particular economic unit in which a lender is satisfied to look initially to the cash flows and earnings of the economic unit as the source of funds from which a loan will be repaid and to the assets of the economic unit as collateral for the loan." Risk and Balance Sheet Treatment It is important to focus in more detail on two aspects of project financing, risk and balance sheet treatment. The assessment of the various elements of risk in a project and the sharing of that risk between sponsors and lenders is the most critical feature. At one end of the spectrum is full absorption of risk by the sponsor(s). This can be described as "on risk" or "on credit" or "full recourse" to the sponsor(s) and is effectively a corporate financing. At the other end of the spectrum the lenders absorb the whole risk in a non-recourse financing which is "off risk" or "off credit" for the sponsor. The other aspect is the sponsor's balance sheet treatment. If the balance sheet of the economic unit undertaking the project and the financing need not be consolidated into the balance sheet of the sponsor (because ownership does not exceed 50%) then the financing may be described as off-¬balance sheet. If consolidation is required then the financing is described as on-balance sheet. Most project financings involve some recourse to the sponsor, i.e. they are limited recourse. Very few are non-recourse or off credit to the sponsor. Limited recourse financings may be on-balance sheet although many may also be off-balance sheet insofar as consolidation is concerned. However, sponsor support may very well be a contingent liability to the sponsor and require disclosure by way of note to the balance sheet should consolidation not be required. CORPORATE FINANCE CONTRASTED A financing which is on credit or full recourse to the sponsor, whether it is directly borrowed or guaranteed by that sponsor, is a corporate financing. Lenders will tend to base their credit assessment on a historical assessment of the sponsor's activities and its financial results rather than an assessment of the project or a detailed assessment of the future activities and prospects of the sponsor. PROJECT FINANCE - A BORROWER'S PERCEPTION Although CRA could choose to arrange all finance on a corporate basis (except perhaps for the very largest projects or acquisitions), project financing techniques provide a number of specific advantages which CRA has noted and which should be carefully considered by a project sponsor. Advantages

Jan 1, 1985

By I. A. Goddard

INTRODUCTION This paper deals with the development of the sublevel open stoping (SLOS) method in lead orebodies at the Isa Mine of Mount Isa Mines Limited, during the last ten years. Open stoping in different forms has been used at the Isa Mine for many years. Prior to the period under review, stopes were small, pillars were not always recovered, and scrapers extracted the ore. By the end of the sixties, the use of load-haul-dump units was becoming more widespread. Wagner ST5's were the mucking units for the lead cut and fill stopes. Some of the open stopes in 5 orebody above 13 level had 100 kW slushers, but the more southerly stopes were the sites for the introduction of diesel front-end loaders for extraction. In the early seventies, new methods were used in the block of six stopes in 2 and 5 orebodies between 8 level and 13 level and a trial stoping project was undertaken in 7 orebody between 11 level and 13 level to determine possible stope dimensions for the extraction of the Racecourse orebodies below 13 level. By the mid-19701s, stoping was well underway in 5, 7 and 8 orebodies between 13 level and 15 level, using the 'triplet' system, incorporating cemented hydraulic fill to allow greater pillar recovery. As the eighties were entered, development of the Racecourse orebodies below 15 level commenced, as did preparations for 1 orebody in the upper levels of the north end of the mine. In both cases, the pillar recovery method has been changed to reduce the amount of cemented fill required for pillar recovery. GEOLOGY Most of the lead orebodies at Isa Mine lie chiefly to the north of the central shaft complex. They are bedded sulphide deposits in a host rock called Urquhart Shale, which dips at roughly 650 to the west. The main minerals are galena and sphalerite, with the silver mineral, freibergite, being contained in the galena. To the hangingwall of the sequence are the Black Star orebodies (1, 2 and 5) which are relatively wide, pyritic and with low to above average grade lead. The Racecourse orebodies (6 to 16) lie to the footwall, and have a large variation in width, low to high grade lead, and gradation in the lead to zinc ratio from north to south. Stope outlines are often determined by economic or engineering considerations rather than geological. The published extraction reserves are 56 million tonnes of primary ore, containing 150 grams of silver per tonne, 6.4% lead and 6.5% zinc. Traditionally, it has been regarded as lead ore, although the dominant revenue earner varies from time to time. In the Black Star orebodies, the ore and hangingwalls are more competent and open stoping has long been used. The major Racecourse orebodies which have been open stoped are 7 and 8 orebodies. This has been where the orebodies are wider (to the south) and where hangingwall conditions allow. This latter aspect has been greatly influenced by the presence of 'silica dolomite1. This tough, relatively homogeneous, non-bedded rock is, in fact, the host rock for the copper mineralisation at Mount Isa, and provides a competent hangingwall for some of the lead stopes. While the shale's bedding and jointing has a major influence on the ground conditions, there is a major fault system which causes local problems. The principal virgin stress direction is perpendicular to the bedding, but the local stress situation is complicated because of shielding by filled stopes in the hangingwall copper orebodies and because of the interaction between orebodies being extracted to the footwall. Most development on strike is mined with a 'shanty-back’, with the back being as close to normal to the bedding as possible. This is near parallel to most jointing and the principal stress direction. Figure 1 is a plan view of 14 level north, which provides a representative horizontal section through the orebodies. A typical cross section is shown in Figure 2. The narrow, parallel footwall orebodies can be seen to differ from the wider hangingwall orebodies.

Jan 1, 1981

By H. Rumfelt

The author demonstrates an approach for analyzing overcasting requirements for a stripping project. This approach to the problem employs indicated trends in the relationship of the weight of the machine (only electropowered draglines are considered) to its ability to do stripping work. Strip mining in the domestic coal industry is contributing a greater proportion of overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely). Accompanying these changes, there have been continuing studies searching for procedures to appraise deeper stripping problems. Although the only known practicable way to accurately evaluate a proposed stripping venture is to make studies (including cost estimates) step by step, it is nevertheless desirable to have a quick method for making preliminary evaluations of potential strip mining operations. A recently devised digital computer method of providing a preliminary simple overcasting analysis for a stripping prospect relates the indicated trends in the relationship of the weight of the machine to its ability to do stripping work. In addition, this approach employs situations where the geometry of each cut-and-spoil section is assumed to take certain defined relationships for varying overburden depths. Slopes are necessarily considered to be stable, which means such practical factors as the mechanics of soils are neglected for the sake of convenience. Definition of Terms: Photographs A and B show a shovel-type and a dragline-type of simple overcast operation, plus terms used to denote certain parts of a pit. Pits that follow a straight line when projected on a horizontal plane are referred to as straightaway. It has been assumed that all section drawings accompanying this article pertain to straightaway cuts which, in turn, means that areas can be compared by relative volume. The volume of overburden is measured in virgin cubic yards. Material displaced from its virgin state to a spoil area normally occupies a larger volume than when in situ; the difference is termed swell, and it is expressed as a percentage of the original volume. For example, if the original cut volume is denoted V cu yd, and the spoil volume is 1.2 V cu yd, the swell is a positive 20 pct. MAXIMUM USEFULNESS FACTOR (MUF) CONCEPT Men experienced in overburden removal give emphasis to the weight of the machine in relation to its value as an excavator. From the writer's understanding, value has been only loosely defined and discussed generally and vaguely. The concept is considered important, however, since it is based upon the observations of many men. It provides a clue for the approach taken to solve deep stripping problems. In the procedure described below, value has been arbitrarily established as the product of the nominal dipper size of the shovel (or dragline) times a functional dumping reach. MUFs—Shovel: A shovel's capability to handle thick overburden is usually limited by its ability to dispose of the spoil. Thus the dumping reach, as well as its dumping height, is significant. The angle of repose of spoil material must also be considered. Although such slope angles vary among different mines, jobs, and materials, a slope of 1.25 to 1, frequently found in both planning and practice, is used by this author in the illustration of this analytical method. The relationship of the shovel's geometry to a stripping operation is shown in Fig. 1. To gain maximum advantage in constructing spoil piles, the shovel is placed so that its tracks adjacent to the spoil are as close as possible to the rib of the coal deposit. A vertical plane passing through the line

Jan 1, 1961

By Paul D. Merica

Jan 1, 1937

By William Fink

ALUMINUM forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has, been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.2 Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560° C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550° or 560° C.; in fact, some of the specimens were the identical ones used by Dix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1930

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined because it is used both as a rock term and as a particle size term. Actually most persons using the term clay realize that it has a double meaning and in most instances define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it so that the definition has to be general. Clay is a natural, earthy, fine-grained material composed largely of a limited group of crystalline minerals known as the clay minerals. Many definitions state that a clay has the property of plasticity when wet, but some clays are not plastic, i.e., halloysite and flint clay; however, most clay materials are plastic when wet. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on some grade scales. Soil investigators and mineralogists generally use 2 microns as the maximum size. The Wentworth scale' defines clay as material finer than approximately 4 microns. Grim' has found it convenient to use the term clay material for any fine-grained, natural, earthy, argillaceous material and in this way can include clays, shales, or argillites, and some soils if they are argillaceous. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, still the term is generally understood by all who use it. Clay is an abundant natural raw material and has an amazing variety of uses and properties which will be discussed in this chapter. In order to understand better the relationships between the clays and their uses, a brief discussion of the structure, chemical composition, and identification of the clay minerals is given. Mineralogical Composition of Clays Clays are composed of certain groups of hydrous aluminum, magnesium, and iron silicates that may contain calcium, potassium, and other ions, which are called the clay minerals, and other minerals of variable composition, which are nonclay minerals. Both clay minerals and nonclay minerals influence the properties of a clay material. In order to understand the relationship between clay minerals and the properties of a clay material, a short summary of the structure and composition of clay minerals is necessary. Any scheme of classification tends to impose a certain rigidity and as new and additional data become available it is necessary to revise classifications. Brindley3 has discussed the classification and structural mineralogy of clays in very lucid fashion and chose a classification based on structural features and chemical composition. Grim2 proposed a tentative classification which is based on the structural attributes of the various clay minerals. This classification is relatively simple and workable, and is shown as follows: I. Amorphous Allophane group II. Crystalline A. Two-layer types (sheet structures composed of units of one layer of silica tetrahedrons and one layer of alumina octahedrons). 1. Equidimensional Kaolin group kaolinite, dickite, nacrite 2. Elongate Halloysite group

Jan 1, 1960

Dubbed "Freeport's Mission Impossible" by the trade press, the company's Ertsberg mine in West Irian nevertheless shipped its first concentrates in December 1972, ahead of schedule. This is a new and great chapter in the history of Freeport Minerals Co. and its contractors. Exploration and construction were only possible by moving equipment and supplies by helicopters. This work was carried out by Petroleum Helicopters, Inc., of Lafayette, La. At the peak of operations six machines were in service manned by 11 pilots and supported by 10 mechanics. During the month of August, with work in full swing 1,604 tons were moved, including 3 DC-6 tractors requiring 18 trips each; flying hours for the month were 636.

Jan 1, 1973

By G. Willard Quick

FAILURES in railroad rails have been of vital concern to engineers; railroad executives, rail manufacturers and the general public for years. Failures from transverse fissures originating from internal nuclei have received particular attention in the past 20 years. Dr. J. E. Howard first reported this type of failure in 1911, as being responsible for a wreck-on the Lehigh Valley R. R. in which several lives were lost. Since then many transverse fissures have been found. In 1919, Waring and Hofammann1 etched longitudinal sections of rails in hot acid and found cracks extending both longitudinally and transversely in certain used rails as well as in some new rails.. Since then it has been thought by many that these "shatter" cracks are the nuclei from which transverse fissures subsequently develop in service. Methods for reducing the rate of cooling rails on the hot. bed have been devised to decrease the temperature gradient and consequently the stress gradient in the rails. A study of the tensile properties of rails at elevated temperatures was made by Freeman and Quick,2 who investigated the properties at temperatures through which rails pass on the cooling bed after leaving the hot saw. In their investigation a special study was made of the ductility of the steels in the temperature range 400° to 700° C. In this temperature range it was found that certain rail and other steels showed a marked decrease in elongation and reduction of area. The phenomenon was called "secondary brittleness" and the temperature range the "secondary brittle range." A tentative explanation was presented that internal failure such as "shatter cracks" and "hair cracks" in rails are the result of thermal stresses developed in the steel structure while cooling through the secondary brittle range. The investigation showed that the magnitude of the phenomenon varies for different heats, but that it did not differ for specimens from different ingots or for different rails in a particular ingot. It was also shown that annealing rail steel at a temperature either above or below the critical

Jan 1, 1932