Search Documents

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum deposit, Eureka County, Nevada, occurs In a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusive. For samples from the 25000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8: 1 at 10-mesh, 8: 1 at 70-mesh, 6: 1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp 1s used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of ± 25%. The error distribution is not based. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1984

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a previous paper.1 The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques.

Jan 12, 1953

By J. B. Clark, F. N. Rhines

THE A1-Mg phase diagram in the composition range from 30 to 60 pct Mg remains uncertain. Four intermetallic compounds are reported in this composition range. All of the published diagrams are in agreement as to the existence of intermediate phases near 37 and 52 pct Mg (Mgl,A1,). Confusion exists, however, as to the number and identity of the intermetallic phases present in the intervening composition range from 37 to 52 pct Mg. Mikheeva and Kurnakovl denote the existence of a phase e near 42 pct Mg. Kawakami," Reiderer? and Laves report a phase near 48 pct Mg. Eickhoff and Vosskuhler, from a critical survey of the literature, composed the diagram shown in Fig. 1, with the exception of the eutectoid horizontal of the e-phase shown at 210°C. RaynorV n a similar survey discounts the existence of the phase proposed by Ka-wakami et al.' at 48 pct Mg and reports a composite diagram similar to that of Eickhoff and Vosskuhler." This uncertainty as to the number of intermetallic phases in the A1-Mg system may be eliminated by annealing a diffusion couple of pure aluminum and

Jan 1, 1958

By AIME

AS with Phil Kraft, referred to on this page last month, travel has always held a great fascination for Raymond Frank Baker and for that reason he determined to become a geologist. He had heard that geologists travel and that was what he wanted to do. Now as chief geologist for The Texas Co. his early wish has been fulfilled-he spends almost one third of his time journeying' from one oil field to another. Mr. Baker was born in New Haven, Conn., on Jan. 11, 1892, and went through the public schools in New Britain. A stalwart New Englander, he attended Yale and in 1912 received a degree in civil engineering. For a year following this he worked as a civil engineer for the New York Central Railroad, but his early urge to travel widely could not be satisfied here. So in 1913 he re-entered Yale and until 1916 studied mining and economic geology. He had a little taste of field work, which later became so enjoyable to him, in the summer of 1915 when he worked with the U. S. Geological Survey as a geologic aid. In 1916 he made his first contact with The Texas Co. when he entered their Tulsa office as a geologist. This early career was interrupted by service in the

Jan 1, 1947

By Irwin Roman

IN a previous paper,1 a method was suggested for determining the depth to a bed in the simple case of a uniform overlying layer of constant thickness. The main purpose of the present paper is to show how a slight modification of that method has been used to interpret specific data obtained in the upper peninsula of Michigan by the staff of the Depart- FIG. 1.-THE TECTONIC CONFIGURATION. ment of Mathematics and Physics of the Michigan College of Mining and Technology. The method of Tagg2 has also been used on the same data, thus furnishing a comparison of the e two methods, as well as a method of using the two methods jointly. The method of measuring the apparent resistivity is that suggested by Wenner,3 and illustrated in Fig. 1. A current I enters the earth at the positive pole C and leaves it at the negative pole D. The potential V of the high electrode A, with respect to the low electrode B is measured by suitable means. The separation of the collinear points in the order shown, DBAC, is 1, the same. for each interval.

Jan 1, 1934

By David R. Poirier

THE activity of carbon in Fe-C-Cr liquid solutions has been measured by Richardson and Dennis,1 Fuwa and chipman,2 and Goto et aL3 Fuwa and Chipman2 have presented their data along with data of Richardson and Dennis1 and utilized an interaction parameter. However, the interaction parameter is only valid for dilute solutions of carbon, because, as indicated, the same interaction parameter does not apply to more concentrated solutions of carbon (i.e., the effect of chromium on the saturation of graphite in liquid iron). Ohtani4 has attempted to account for the effect of carbon concentration on the interaction parameter; however even his analysis does not apply to the saturation data. Also, the effect of temperature on interaction parameters must be taken into account. Therefore, in any process where the concentration of carbon and/or the temperature changes (such as solidification), the use of an interaction parameter is not adequate to know the activity of carbon. The purpose of this communication is to make use of the existing data on the effect of chromium on the activity of carbon in liquid iron solutions in such a way that the activity can be described as a function of both composition and temperature. The method is an extension of Rist and chipman's5 analysis for the binary Fe-C solutions. As in Rist and Chipman's analysis, the activity coefficient is assumed to obey the relation: log y1 = at(l -X1)2 + It [1]

Jan 1, 1969

By M. Kitada, U. Kawabe, F. Ishida, T. Doi

The relations between micros tructures and critical current density in transverse magnetic field were experimentally investigated due to each transformation of the 0 to 0' + P" phases at 700' C for superconductmainly examined using replication electron microscopy. The ß' or a precipitates were found to pin down magnetic flux lines in these alloys. The effects of precipitation upon the critical current density were discussed in relation with the size, spacing, and characler of these precipitates. HIGH magnetic field superconductors, such as Nb-Zr, Nb-Ti, and Nb-Zr-Ti alloys, have been recently put to extensive practical use as winding materials for superconducting magnets.13 The critical current density of these hard superconductors under an applied magnetic field is an important characteristic for magnet materials and is very sensitive to metallurgical structure. It is generally known that the critical current density is increased by introducing dislocations and precipitates into a superconductor; that is, dislocations and precipitates are presumed to be barriers that hinder quantized flux lines from moving.4'5 Theoretical6'7 and experimental analyses of the motion of flux lines and the interaction between flux lines and various defects have already been reported by many authors. Metallographic analysis of high magnetic field superconductors such as Nb-Zr and Nb-Ti is difficult, so that no quantitative relationship between microstruc-ture and critical current density has been established yet. In this paper, the effect of precipitation on the critical current density in magnetic field was investigated for two superconducting alloys, Nb-40Zr-10Ti and Nb-5Zr-60Ti. In these alloys the resistive critical field H, at 4.2oK was about 100 kG and the critical current density Jc at 80 kG was of the order of 104 amp per sq cm.13-l5 The superconducting properties were examined in relation to the microstructural changes due to transformation of i) the ß to ß' + ß" phases at 700°C for Nb-40Zr-10Ti alloy and ii) the ß to a + ß phases at 500°C for Nb-5Zr-6OTi alloy. The effect of size, spacing, and character of precipitates on flux line pinning was in particular examined. The microstructures were studied by means of residual resistivity, microhardness, and tensile strength measurements as well as by X-ray diffraction, optical, and replication electron microscopies. I) EXPERIMENTAL PROCEDURE Pure niobium, zirconium, and titanium, in the form of rods 0.8 cm in diam, served as raw materials. Results of chemical analyses of these rods are given in Table I. Ingots of the alloys, 0.4 cm in diam and 3 cm in length, were prepared by means of levitation melting, utilizing a copper mold in an argon-gas atmosphere. Samples from the ingot then were cold-worked by grooved mill to 0.2 cm in diam, heat-treated homogeneously (in the ß phase region) for 5 hr at 1100° in a vacuum of 1 x 106 Torr, and finally cold-drawn to 0.025 cm in diam. For heat treatments, samples were wrapped in niobium foil and sealed in an argon-gas atmosphere in fused quartz capsules. Water quenching was done after each heat treatment. Subsequently H-J, were performed at 4.2° by slowly transporting the current through the samples 4 cm long, under transverse magnetic field, until the least detectable resistive terminal voltage was observed. The resistive critical field H, was taken as the field at which 100 pv appeared at 4.2°K across a sample 3 cm in length, with a current of 5 ma. The critical temperature T, was measured by means of a conventional four-probe resistivity technique and taken as the temperature at which the sample resistance reached one-half of full restoration of the normal-state resistance with a current l ma flowing through a sample 2 cm in length. Precipitates were observed by means of optical microscopy and carbon replication electron microscopy. The etching solution consisted of 5 ml HF, 10 ml H2SO4 10 ml H2O2, and 50 ml H2O, and shadowed carbon replicas were examined in a itachi HU-11 electron microscope operated at 50 kv. X-ray diffraction photographs were taken by a 11.46-cm-diam Debye-Scher-rer camera using copper Ka radiation. The micro-hardness was measured under a load of 200 g using

Jan 1, 1969

By M. E. Shank, J. Wulff

At the present time, the designer of dies for metal powder pressing is handicapped by relative ignorance of stress distribution and frictional effects at the interior surface of the die. Unckell was the first to develop a method for the study of wall friction. He used three Brinell balls on which the die rested during pressing. The total frictional wall force was determined by the size of impression these balls left on a soft metal plate. Since the method does not give radial pressures, or distribution of such pressures, coefficients of friction could not be determined. Although Unckel measured density distribution, he was not able to determine radial or shear stresses. Shaler2 has proposed theoretical expressions for the stress and density distribution within cylindrical compacts during pressing, in accordance with the experimental results of Kamm, Steinberg, and Wulff.3 By application of Siebel's method,4 Kamm et a13 plotted stress trajectories for two compacts. From the stress trajectories they calculated coefficients of friction from point to point along the die wall. As pointed out by Shaler in the discussion of Ref. 3, these values are based on progressive point-to-point calculations on finite size grid squares across the compact. In the region of the die wall such calculated values may therefore have considerable cumulative error. The purpose of the present paper is to develop an experimental method by which the nonhydrostatic pressures and shears acting on the interior wall of a cylindrical die can be measured. Such measurements can then he correlated with existing data to aid in the explanation of the pressing process. The method used is based on the elastic: properties of the thick-walled tube used as the die. The principle of super-position of force systems on an elastic body is assumed to hold. Electric strain gauges were mounted in adjacent positions on the exterior die wall in order to get an exact measurement of the variation of tangential strain over the length of the die during pressing. While in this paper, measurements in terms of only tangential strains are considered, it is well to note that similar calculations may be set up for axial strains. The latter are not preferred, since they tend to be smaller than the tangential strains and therefore permit less sensitive measurements. Discussion in this work is restricted to compacts pressed from both ends, since the elastic deformation of the die is then more amenable to analysis. Before choosing the electric strain gauge method, a more direct line of attack was considered and discarded. The discarded idea was the insertion of a pressure gauge through a hole in the die wall.* The gauge would have been in the form of a small piston. If pressure were exerted against such a gauge, it would move outward along a radius of the die. One disadvantage of the scheme is its inability to measure shears along the die wall. Another more serious disadvantage is the disturbance caused by the device itself. It would serve to change the forces it was designed to measure. No matter how small the movement of the gauge, when pressure is applied a discontinuity would exist in the wall surface at that point. Due to the stress concentration caused by the hole, abnormal deflections of the die wall would occur around the gauge. During pressing, powder would be forced into the resulting depression. The depression would then become larger with increasing compacting pressure. Powder, not being a fluid, is capable of supporting shear. The ease with which it would flow into the die wall depression to further move the piston is an indication, not of the radial pressure at that point, but of the state of shear retarding the movement. Thus the "pressure" gauge is really a criterion of flowability, and of the capability of the powder to support shear. For these reasons, it was decided that the electric strain method, herein employed, was more reliable, if more indirect. The gauges and lead wires, mounted on the external die wall do not in any way affect the behavior of the metal powder or the die during pressing. Theory of the Method THE EFFECT OF RADIAL PRESSURE ON THE DIE WALL Effect of a Single Small Band of Hydrostatic Pressure Consider a die which is a thick-walled cylinder of outer radius R. and inner radius Ri. If over a small finite length L there is a normal pressure P, a tangential strain distribution at the outer wall results. This is shown schematically in Fig 1. The exact shape of the curve may he predicted by an extension of the theory of a semi-infinite beam on an elastic foundation.6 This

Jan 1, 1950

By J. B. Conway

Stress-vuptuve data for several of- the refractory metals are frequently found to yield a linear relationship between the Larson-Miller parameter and the logarithm of the applied stress. In such cases linear stress-rupture isotherms result with slopes bearing a definite relationship to the temperature. It also follows that the stress to produce rupture in a certain period of time will be linear in temperature. Data for several refractory metals have been reviewed and excellent linearity is shown in this type of isochronal plot. In addition, the af ore - mentioned lineavity leads to a linear relation between the log of the stress to produce rupture in a certain time and the homologous temperature. This has been illustrated for the Group VI-A metals, tungsten and molybdenum. EXTENSIVE use has been made of the Larson-Miller' parameter in the interpolation and extrapolation of stress-rupture and creep data. In those cases where this particular parametric approach is applicable a convenient and fairly straightforward procedure is made available for the correlation of experimental stress-rupture data. It is quite common to employ this parameter in the form of a master rupture plot in which the parameter, T(C + log tr), is expressed as a function of log stress. In many cases this functional relationship in log stress is linear within acceptable accuracy and hence the following relation results: where P is the parameter, C is the Larson-Miller constant, T is the absolute temperature, t~ is the rupture time, a is the stress, and a and b are constants. Examples of such a relationship are contained in the work of Green, Smith, and 01son2 dealing with high-temperature rupture behavior of molybdenum and in the work of Green' dealing with the high-temperature behavior of tungsten. In addition, pugh4 has shown a similar linearity for some fairly low-temperature data for molybdenum. It can be shown that when the relationship in Eq. [I] is exhibited certain generalizations can be made concerning the form of the stress-rupture isotherms. For example, rearranging yields: For a given material (constant C) at a given temperature the first term on the right-hand side of Eq. [2] is a constant and hence this equation defines a straight line when log stress is plotted as a function of log-rupture time. This is recognized as the standard form usually employed in this type of data presentation. Such linearity then suggests the linear form of the Larson-Miller parameter. Or, in other words, the linear parametric relationship in Eq. [2] results only when the stress-rupture data are linear on a log-log plot of stress vs rupture time. Another interesting observation can be made in regard to Eq. [2]. It can be noted that the slope of the stress-rupture isotherms is given by - T/b and hence a direct calculation of the constant b is available. It also follows that since the value of b is the same for all temperatures the slopes of the various isotherms on the log-log stress-rupture plot cannot be the same. Indeed, the existence of the relationship in Eq. [2] precludes a system of parallel lines on this common stress-rupture plot. As a matter of fact it further specifies that in addition to being nonparallel the slope of these isotherms must decrease (i.e., become more negative) with increasing temperature. Such a condition is indeed found to exist in the case of the stress-rupture data reported for molybdenum.' As a corollary to the above, it may be stated that stress-rupture data which do not lead to a linear log-log stress-rupture plot or whose isotherms do not exhibit a decrease in slope as the temperature increases will not yield the linear relationship of Eq. [I]. Applying Eq. [2] to two different temperatures and solving for C yields: Eq. [3] affords a simple and rapid method for calculating the Larson-Miller constant from the log-log stress-rupture plot. The slope of a given linear isotherm is measured and the value of "b" calculated based on Eq. [2] as: slope = - -Tb Then at an abscissa value of 1.0 hr (making log tr in Eq. [3] equal to zero) read the stress corresponding to rupture for two different temperatures. Substitution in [3] yields: A value of the Larson-Miller constant can thus be calculated from a few simple mathematical procedures employing data read directly from the log-log plot of the stress-rupture data. Of course, it is not to be overlooked that the above reasoning has been based on the linear relationship of Eq. [I] being applicable. However, if as mentioned above the log-log plot is

Jan 1, 1967

By E. A. Steigerwald, G. L. Hanna

The influence of work-hardening exponent on the variation of fracture toughness with material thickness was studied for high-strength steel, aluminum, and titanium alloys. The results indicate that, when materials are compared at similar fracture toughness to yield strength ratios, the material with the lower work-hardening exponent undergoes the transition from flat to slant fracture at a larger thickness than material with a high work-hardening exponent. In the thickness range where complete slant fracture is obtained the reverse is true and a lower work-hardening exponent results in a lower fracture toughness. The influence of work-hardening exponent on fracture toughness is, therefore, dependent on the particular fracture mode. In the transition region a low work-hardening exponent is beneficial for fracture toughness while in the 100 pct slant region it is detrimental. THROUGH the use of fracture mechanics analyses, the influence of geometric variables on the crack propagation resistance of structures can be interpreted with reasonable consistency. However, in order to gain a more complete understanding of the fracture process, the influence of material parameters on crack propagation must be defined and coupled to the macroscopic fracture mechanics approach. The work-hardening exponent, which characterizes specific material behavior, may serve as an effective parameter to allow some degree of coupling to be accomplished. In the extension of a crack in a specimen of suitable dimensions the propagation process occurs in a stable manner when the crack extension force is balanced by the resistance to crack extension, which exists in the material at the crack tip. As the applied stress, and therefore the crack extension force, on the specimen increases, the resistance also increases primarily because the effective plastic zone at the crack tip, which is the main energy absorption process, becomes larger. Since the work-hardening rate of a material influences the stress-strain relationship, it will also influence the energy absorption process in the plastic enclave at the crack tip and hence should have an effect on crack propagation. A number of studies have been made correlating the strain-hardening exponent or the strain to tensile instability with the ability of a material to resist fracture. Gensamer1 concluded that a low-strain-hardening exponent would result in a steep strain gradient at the base of a notch. He reasoned that a large work-hardening coefficient would result in high-energy ab- sorption due to the increased area under the stress-strain curve. Larson and Nunes2 experimentally observed in Charpy tests on steels heat-treated to below 200,000 psi yield strength that the energy to failure in the fibrous mode, i.e., above the brittle-to-ductile transition temperature, was logarithmically related to the strain-hardening exponent. In order to avoid the complicating effects present in studying materials which undergo a brittle-to-ductile transition, Ripling evaluated the notch sensitivity of a variety of fcc metals with varying work-hardening exponents.3 The results indicated that the relative notch sensitivity, as determined from tests on specimens with a sharp notch, decreased with increasing values of strain hardening. Although the energy required for ductile or fibrous fracture increases with increasing work hardening, high-strength steels often exhibit improved crack propagation resistance when heat-treated to obtain low values of strain hardening.4,5 An analysis of whether low strain hardening is beneficial or detrimental to crack propagation resistance must depend on the particular fracture criterion involved. At temperatures where the material is relatively ductile and the development of a critical strain is required for fracture, high strain hardening increases the energy required to produce failure. In the transition region and below, however, a critical stress law appears to be valid6 and a low rate of work hardening may produce superior resistance to semibrittle crack propagation. The experimental program is aimed at studying these possibilities and determining the specific influence of strain hardening on the crack propagation resistance of several high-strength materials. MATERIALS AND PROCEDURE The alloys, chosen as representative of various classes of high-strength materials, are summarized in Table I. The heat treatments evaluated along with the smooth tensile properties are presented in Table 11. Pin-loaded sheet tensile specimens were employed to determine the smooth tensile properties. A strain gage extensometer (measuring range 0.200 in.) was used at a strain rate of 0.02 in. per in. per min. The work-hardening exponents were determined from the stress-strain curves generated in the smooth tensile tests and the assumption that the portion of the stress-strain curve beyond the yield point can be described by the power relationship: where a is the true stress, P is the true plastic strain,

Jan 1, 1969

By R. C. Padfield

Experience over a 3-year period in Bethlehem Steel Corporation's plants has demonstrated the reliability of open-hearth roofs of bonded sprung-arch constructzon with burned basic brick. The design principles lor constructing these roofs include a minimum hot-strength requirement for the basic brick, expansion allowances that extend the full roof thickness, structural members to control arch contour, and a specified minimum roof rise. The greater stability of bonded roofs is explained in terms of the basic stress patterns of ring constrution and bonded construction. PRIOR to the development of successful sprung-arch roofs of basic brick, the majority of open-hearth furnaces in the United States were operated with sprung-arch roofs built of silica brick. Although many silica roofs used on open-hearth furnaces were ring-arch construction, Bethlehem Steel Corp. used bonded-arch construction because of its greater stability. In ring construction, each ring of brick is separately keyed and comprises an independent arch with the straight joints between rings traverse to the longitudinal axis of the furnace. In bonded construction, the bricks are laid in rows starting from the skewbacks so that the straight joints run parallel to the longitudinal axis of the furnace. Each brick in a given row is laid so that it spans the joint between two bricks in the row beneath it. Thus, the transverse joints across the arch are broken and the arch rings are thereby interlocked or bonded. When basic roofs were first being developed, the basic brick that were available had low hot strength. Such brick could not be safely used in sprung-arch construction without some means of suspending them. With the development of higher firing techniques by brick manufacturers and the recently introduced direct bonded bricks with high hot strength, the use of burned basic brick in sprung-arch roofs became feasible. The availability of high hot strength basic brick coupled with the potentially lower cost and proven stability of bonded construction prompted Bethlehem's Research Department to study the possibility of using basic brick in bonded roofs. With the full cooperation of plant ceramic engineers and open-hearth superintendents, particularly in 3 years of fur-nace trials, we developed the design criteria for bonded roofs and the corresponding property requirements for the basic brick that are discussed in this paper. DESIGN PRINCIPLES OF SPRUNG-ARCH BRICK ROOFS Stresses in Fixed Arches. A sprung-arch open-hearth furnace roof is generally built on rigidly held skewbacks. The constraint of the fixed support at each end adds a bending moment to the horizontal and vertical reactions at the ends of the arch. Fig. 11 shows the positive direction of forces acting on an arch fixed at both ends. Fixed arches can be analyzed when the members are continuous and have elastic properties. However, brick are inelastic, and arches built with individual brick segments cannot carry tensile stresses. Therefore, for practical solution of brick arches, empirical formulas have been derived from elastic theory that place design restrictions on arch dimensions to avoid development of tensile stresses. McDowell2 cites three main conditions for stability in sprung brick arches: 1) the thrust line of the arch should be maintained in the middle third of the thickness to avoid tensile stresses and resulting open joints in inner and outer curves of the arch; 2) the angle between the line of thrust at any joint and a line perpendicular to the joint must not exceed the angle of repose between brick; and 3) the maximum pressure at any point must not exceed the strength of the arch materials at furnace operating temperatures. The first and third conditions are particularly important in designing sprung-arch basic roofs because of the comparatively low hot strength of basic brick. According to McDowell's equation, if the thrust line is maintained within the middle third of the arch thickness, the unit pressure is obtained as follows: where p = unit pressure in psi, F, = resultant thrust normal to skewback in pounds per foot, t = arch thickness in inches, and z = distance in inches of thrust line from arch axis. When the resultant thrust normal to the skewback acts along the arch axis, z equals zero and unit pressure is simply the thrust divided by the cross-sectional area. If the thrust line moves to the limits of the middle third of the arch thickness, beyond which tensile forces would develop, z then equals one-sixth of the arch thickness and the unit pressure is double that when the thrust line is acting

Jan 1, 1968

By Dennis E. Stover

Grade control for in situ uranium leaching is maintaining, at desired levels, the uranium concentration in the pregnant lixiviant which feeds the extraction (ion exchange) circuit. This differs from grade control in conventional mining in that in situ grade control is imposed subsequent to rather than prior to leaching without the direct observation and control possible in conventional mining and milling. Grade control is a necessary engineering task through the entire project life, beginning with preliminary evaluation and design and ending only when the final wells are shut in. More specifically, this task is associated with designing the initial well field, maintaining productivity during well field operations, and planning well field expansions to compensate for the depletion of existing wells. Our aim during each of these phases is to maximize uranium productivity while ensuring that we are developing information necessary for future phases. Throughout this task, we remain cognizant of the fact that uranium productivity is a function of both the complex geologic and operational parameters of the project. A minimum list of significant geological factors must include the following: . Host formation mineralogy . Uranium mineralogy . Permeability . Ore quality (grade and thickness) Our concerns are not limited to average or general descriptions of these factors. The interactions among the factors as well as localized variations among them are far more important in obtaining high productivity from a deposit. For example, an ore body may display an average permeability of one darcy but have its high grade ore confined to regions with permeabilities less than 500 millidarcies. This relationship between ore grade and permeability must be understood early in the project life if the operation is to be successful. Similarly, the fundamental operating parameters for the well field include those items which enable us to distribute the lixiviant within the ore as well as the chemistry which will dissolve the uranium minerals. A minimum list of such factors will include: . Well design . Well efficiency . Well bore damage . Pattern size and shape . Oxidant type and concentration . Complexing agent concentration - pH The interactions between these variables and the complex geological variations create a situation which often defies quantitative analysis. Hence, we have adopted a statistical approach when correlating production history with these parameters and the quality of the correlations improves as the number of wells operated increases. However, the correlations are often specific to an ore body. We find that we must tailor the process to meet the unique geologic parameters of each ore body. PHASE 1: INITIAL WELL FIELD DESIGN Designing the initial well field is perhaps the most difficult phase because we have the smallest data base from which to predict performance. We will have conducted numerous laboratory tests and, perhaps, field pilot tests to select the lixiviant system and to characterize the geologic parameters. However, we will learn a great deal more about the deposit and its productivity during actual commercial scale operation. Fully acknowledging its limitations, we will, as a starting point, assume that uranium productivity will be directly proportional to the quality and quantity of recoverable reserves. Future deviations from this assumption will be plentiful and result from our limited understanding of the aforementioned interactions between and among the operational and geological factors. However, in planning the initial field, estimation of the quantity of leachable uranium present at levels above the economic grade and grade-thickness limitations is a priority task. (The concentration of uranium in the ore, the ore grade, is expressed in units of weight percent. The grade-thickness of the ore is the product of the average grade and ore thickness expressed in units of percent-feet.) These parameters provide a direct indication of the quality and quantity of ore. They are determined from gamma logging of closely spaced drill holes (50 to 100 foot centers being typical) accompanied by uranium core analysis or direct uranium assay logging. Gamma- logging measures gross gamma radiation which emanates from uranium decay products and indicates only the possible presence of uranium. Direct uranium assays are necessary to confirm this presence and the true location and quality of the reserve. From this information, an estimate of the in-place uranium reserve is formulated. Utilizing the above data, we begin to assess the quantity and quality of the leachable reserve. Analysis of self-potential and resistivity logs in conjunction with uranium logs will identify those zones which contain uranium and display apparent high permeabilities. Similarly, zones with extensive calcite cementation or dense clay sedimentation are located and uranium within such zones is excluded. (Interpretation of these logs should be confirmed

Jan 1, 1980

By L. D. Jaffe

IT is now well established that quenched and tempered titanium alloys have much better ductility when the quenching is from a two phase a-B structure, rather than from an all B structure. The corresponding microstructural differences, however, have not been shown in previous publications. Accordingly, specimens were cut from a % in. rod of commercial RC-130A, containing 7.9 pct Mn and 0.12 pct C, which had been previously hot rolled, heated 1 hr at 1100°F, and air cooled. (The same heat has been studied by others." 7 Samples about 1/4 in. cube were heated in helium 1/2 hr at 1450' or 1700°F, quenched in brine, tempered in helium 1 hr at various temperatures up to 1250°F, and quenched in brine. They were then sectioned and metallo-graphically examined, using an etchant of HF-HNO, in glycerine. As quenched from 1700°F, the microstructure observed was clear /3. (Probably also present was U, as the hardness was 400 Vhn, but w is not yet reliably revealed by any metallographic technique.) When the /3 quenched alloy was tempered at a high temperature, a precipitated as a grain boundary film

Jan 1, 1957

THERE have been two important accomplishments of the Truman administration; the Hoover Commission report on inefficiency and waste in government and the report of the Paley Commission on the natural resources of the United States. Both reports are in the interest of the American people and should transcend the boundaries of political parties. Both reports are starting points for the formulation of policies which must be continuously revised to meet changing conditions. Regardless of the outcome of the election the principles embodied in these two great documents must be kept alive. The Paley report is right in our own bailiwick of mineral raw materials and it behooves us to study it carefully as our responsibility to posterity. To those in the mining industry who have limited their field of observation to moving rock or to metal prices it may come as a surprise that our production of such staples as copper, lead, and zinc has fallen behind increased requirements to the point that substantial tonnages must be imported. Iron ore is next on the list and everybody knows that such metals as tin, tungsten, chromium, manganese, nickel, and cobalt are imported almost exclusively. The crisis in raw materials pointed up by the Paley report has been reported annually by Elmer Pehrson and others to small gatherings at the Mineral Economics Division sessions at the Annual Meeting for as long as we can remember. In September 1949, the United Nations Economic and Social Council held an international resource conference at Lake Success which disclosed these same grave conclusions: - Consumption of raw materials is multiplying at an alarming rate, faster than discoveries or replacements are being made. - Production has been wasteful and utilization lavishly beyond enginee¬ing and practical requirements. - Industrialized nations are depleted and many raw materials consumed by industry are not found in the industrialized countries. - Nations formerly exporters of raw materials are increasingly building their own consuming industries. - Political forces in the world are limiting access to raw materials. The Paley Commission selecting the quarter century, 1950 to 1975, to project raw material requirements for the United States, pointed out obstacles to meeting these requirements, and made recommendations for procurement. It is not important that we disagree that cobalt consumption will reach 344 pct of present, or fluorspar 187 pct when iron and ferroalloys are only expected to increase 75 pct. What is important it that the fabulous appetite of the United States for mineral raw materials has consumed more since World War I than was consumed by the entire world in all recorded history prior to 1914. And, unless the people of the United States are satisfied to remain at their present standard of living (which is unthinkable) this consumption is correctly plotted by the Paley Commission as continuing to expand. If the U. S. is to continue on a course of progress, it must procure raw materials wherever it can at the lowest possible cost. Natural resources are clearly an area in which the broadest cooperation between industry and government must exist to achieve efficient exploitation, economic consumption, and expansion of sources of supply. The message of the Paley report requires action comparable to that of the North Atlantic Pact. Its implication is as significant as military preparedness. It is a world problem. It is a mining engineering problem. Don't let it die!

Jan 1, 1952

Jan. 7, 1952, AIME, Boston Section, Massachusetts Institute of Technology, Campus Room, Graduate House, Cambridge, Mass. Jan. 8, Society for Applied Spectroscopy, 6 pm, supper, Tosca's; 8 pm, meeting, Socony-Vacuum Training Center, 63 Park Row, New York. Jan. 9, AIME, Chicago Section, Chicago Bar Assn., 29 S. La Salle St., Chicago. Jan. 13-15, Institute of Scrap Iron & Steel, Waldorf-Astoria, New York. Jan. 14-1.6, AIME, Minnesota Section, Hotel Duluth, Minn. Jan. 14-18, SAE, annual meeting, Hotel Book-Cadillac, Detroit. Jan. 1.6-18, Society of Plastic Engineers, Inc., annual national technical conference, Edgewater Beach Hotel, Chicago. Jan. 17, AIME, New York Section, Mining Club, 33 Broadway, New York. Jan. 1.7, AIME, Utah Section, Newhouse Hotel, Salt Lake City.

Jan 1, 1952

By H. E. Mussey

When the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then completed were referred to as monumental.' Their dimensions are givcn in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 1, 1925

By W. H. Bassett

W H. BASSETT was elected first vice-president at . the executive session of the new Board on Tues- day afternoon. Karl Eilers, H. Foster Bain, Thomas T. Read, and H. A. Maloney were respectively re-elected as treasurer, secretary, assistant secretary and assistant treasurer. The new Executive Committee will consist of W. H. Bassett, Chairman, and Richard Peters, Jr., H. C. Bellinger, E. De Golyer, Edgar Rickard. The Finance Committee will be J. V. W. Reynders, Chair- man, Henry Krumb and H. G. Moulton. George D. Barron was reappointed Chairman of the Admissions Committee, and F. Julius Fohs put in charge of the Papers and Publications Committee.

Jan 1, 1929

By AIME AIME

0 N March 5, at Carnegie Hall, Cleveland, the Ohio Section held a joint meeting with the Cleveland Engineering Society, and the local sections of the American Chemical Society, American Society of Mechanical Engineers, and the American Society for Steel Treating. Prior to the meeting there was an informal dinner attended by 50 men. Then followed an address, "The Principles of Corrosion Protection," by Ulick R. Evans, the well-known British specialist in this problem. There were 266 present, presided over by Zay Jeffries, president of the American Society for Steel Treating and a member of the Cleveland Engineering Society. The address was well received and some discussion followed

Jan 1, 1929

In accordance with the usual custom, manuscripts to be presented at the next meeting of the Institute must be in the hands of the, Secretary before July 1, 1917. Manuscripts to be properly distributed in advance of the meeting must be in the hands of the Secretary before June 1, 1917. At the last meeting of the Institute 45 papers were presented, and 42 of them were actively discussed. This experience makes us believe that advance distribution is the best possible means of getting a good discussion of papers and of securing for them the interest of the members of the profession. It will be impossible, however, to give the papers proper distribution if they bare not received before June 1, 1917.

Jan 4, 1917

By Walter Kauenhowen

Germany's crude-oil production during 1937 totaled 3,174,157 bbl., an increase of 1.9 per cent over the 3,112,494 bbl. produced in 1936. According to official published data, and using a conversion factor of 1 metric ton = 7 bbl., the oil production of Germany in 1937 by fields was as follows:

Jan 1, 1938