Search Documents

By C. Diaz, S. W. Marcuson, K. I. Burgess

Deep roasting in fluid bed roasters is the first unit operation in Inco&apos;s "roast-reduction smelting" process for the treatment of nickel sulphide concentrates. The roaster product, a low sulphur calcine, is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte which is then converted to low (<1%) iron matte in Peirce-Smith converters. Due to the deep roasting, a minimal amount of sulphur dioxide is evolved in the smelting and converting stages. Sulphur is eliminated from the concentrate almost exclusively in the roasters in a single, continuous, strong, gas stream suitable for treatment in an acid plant. This paper discusses the commercial scale testing of deep fluid bed roasting of nickel concentrate at Inco&apos;s Thompson Smelter as part of two commercial scale campaigns on roast reduction smelting conducted in 1981-1982. Slurry feeding, practised during the second campaign, permitted excellent control of the air/concentrate ratio in the roaster and, in turn, good control of sulphur elimination (about 80% of input). Smooth autogenous operation with high oxygen efficiencies (about 95%) was promoted by operating at bed temperatures of830°C to 850°C with calcine recycle. High throughputs and the desired metallurgy were achieved. The extensive testwork conducted during the two experimental RRS campaigns demonstrated thot deep fluid bed roasting of nickel concentrate at high oxygen efficiency is a technically viable operation.

Jan 1, 1994

By J. N. Cram

"The comments given are to help allay generally accepted ideas that the handling of arsenic as arsenic-trioxide (As2o3J in and from off gas pyrometallurgical operation fumes is difficult, hazardous and expensive. It need not be any of these things if the basic and rather unique chemic3l and physical properties are understood and taken care and advantage of through present day technologies. These particular characteristics are:-(1) As2o3 sublimes and re-condenses, at a relatively low temperature;(2) As2o3 is, for practical in-plant purposes, insoluble in water at ambient temperatures and quite soluble in water just below the boiling point;(3) residual suspended and dissolved As 2o3 can be removed from water by complete dissolution with very little sulfuric acid, followed by the addition of small amounts of ferrous sulfate and calcium chlorate, with oxidation to the ferric and arsenite state and precipitation of an insoluble ferric calcium arsenate, thereby lowering the As2o3 content of solutions to acceptable levels. Even lower levels of non-toxic forms of arsenic solids and residual As2o3 in the water solutions can be attained by also using phosphate, and lime, along with the above.A background re past arsenic processing methods, present day operations, plus predictions re future trends, and hazards, are outlined."

Jan 1, 1979

"ChairmanThis part of the discussion is intended as an exchange of information between those who have installed rubber liners in their mills and a means of others to get information that may help them decide if rubber liners would be applicable to their mills.To start the discussion and to relate it to the previous section of this symposium Mine Equipment Co. Ltd. have supplied some graphs that will give some idea of the noise suppression that may be expected from the u.se of rubber liners instead of steel. The figures used in preparing the graphs came from installations of rubber liners in Sweden.L. Strah - Mine Equipment Co.The graph, Figure 1, shows on the bottom the octave band range. The noise level generated by the steel liners is represented by the dotted line and lies within the shaded area where it is considered that hearing damage may result. The solid line represents the noise level generated by rubber liners in the same mill and you will see it is below the shaded area. Although it is not marked on the graph I think the decibel range is from 7 5 to 115. The next one, Figure 2 which shows the relative noise levels generated by steel balls and pebbles with both steel and rubber liners shows the decibel range."

Jan 1, 1968

By A. Lemay, G. Morin, C. Desmeules

"Incorporated in 1976, Sidbec Normines was mandated to exploit a deposit of specular hematite at Fire Lake. A combined effort of three companies, Sidbec, which holds 50. 1 % of the actions, British Steel Corporation another 41.67 % and finally Quebec Cartier Mining, a subsiduary of U.S. Steel Corporation, with still another 8.23 %.The deposit is located 60 miles north of the town of Gagnon. The extracted ore is crushed, in a giratory crusher, to-8 11 chunks, and from there, it is transported, by rail, to a concentrator at Lac Jeannine.A concentrate containing 65.5 % Fe and 5.5 % Sio2 is produced, using conventional methods like autogeneous mil ls and spirals. The concentrate is then transported by rail to the Port Cartier installations.The installations in Port Cartier include a secondary concentrator, a pellet plant, and stockpiling facilities for pellets and concentrate. The pellet plant has two product lines in paralel, producing a total designed tonnage of 6 millions tons of iron ore pellets, of which 3mi11ions tons are used in direct reduction furnaces.The secondary concentrator is designed to remove a portion of the silica contained in the ore, usually less than 2 % Si02 should remain from the original 5.5 % Si02 in order to produce iron ore pellets which are well suited for use in direct reduction and electric furnaces."

Jan 1, 1981

By Harry Piers

A RAPID glance over the history of The Mining Society of Nova Scotia shows that in its fifty years of service, which it is now rounding out, the Society has had an honourable career, rendered signal service to the mining industry of the Province, and helped to shape and improve legislation bearing on our mines and minerals, besicles publishing very many excellent papers and subsequent discussions thereon dealing with all subjects in its field of activity. THE GOLD MINERS? CLUB OF NOVA SCOTIA: The Society has the distinction of being generally regarded as the oldest mining fraternity in Canada ( 1). Iris the direct outgrowth or reorganization of The Gold Miners&apos; Club of Nova Scotia, which was organized in March, 1887, at a period when the gold mining industry was very prominent in the Province. Mr. Geo. W. Stuart, who, in 1934, was the only living member of the parent association, informed me that the seventeen Charter Members of The Gold Miners&apos; Club were John H. Anderson, Charles F. Andrews, A. B. Cox, Clarence H. Dimock, George E. Francklyn, L. W. Getchell, John E. Hardman, Alonzo A. Hayward, Major R. G. Leckie, W. L. Libbey, Edward M. McDonald, G. F. McNaughton, George A. Pyke, H. A. Sanders, C. E. Willis, Benjamin C. Wilson, and George W. Stuart. Others joined later in the same year.

Jan 1, 1937

By Herbert D. Drechsler

"THE FOLLOWING are some comments on the article, ""International Trade in Minerals and Economic Development"", by M. Sengupta, published in the October 1976 issue of the CIM Bulletin.Sengupta says in the introduction that ""The mechanism through which this growth (economic development) has occurred is basic ally straight forward"". His statement is quite misleading and perhaps it is better to quote Gerald Meier:""Development economists must operate in an imperfect second-best world, away from the simplified premises of neoclassical economics. Their subject matter is therefore not yet a coherent or self-contained discipline. Denied recourse to a set of general principles, perhaps the student's most sensible introduction to economic development is through a study of 'leading issues' that are at the time a major preoccupation of the development economist and development practitioner"" .Sengupta quotes an authority who wrote 18 years ago. Academic and operating development economists today know full well that existing theory is quite deficient. Sociologists, political scientists and engineers in this field also know that economic, social, political and technical development involves all academic disciplines.Sengupta indicates that tariffs in developed countries prevent less developed countries from supplying refined metal, or manufactured and semi-manufactured products. He lists Zambia, Chile and Zaire as examples of copper concentrate exporters, as inadequately shown in Table 1. He is wrong."

Jan 1, 1977

By S. Y. Mostowy, P. W. M. Shibley

"When Texas Gulf Sulphur Company discovered the Kidd Creek ore body in 1964, a crash program began almost immediately for the design and construction of a modern concentrator. It was necessary to mill two distinct ore types; one containing copper and zinc, the other lead, silver and zinc minerals. The final concentrator design was to handle 9,000 tons of ore daily in three circuits. One circuit was to treat copper-zinc and another lead-zinc ore exclusively on a permanent basis. A central circuit was designed with adequate flexibility to treat either of the above ore types in accordance with planned mining schedules. Ecstall Mining Limited, a wholly owned subsidiary, now operates the mine and concentrator complexes for Texas Gulf. The mine is located 15 miles north of Timmins and the concentrator 15 miles to the north-east along Highway 101. The ore is hauled from the mine to the concentrator over a 17-mile railroad. Initial milling operations began in November, 1966.1 - ABSTRACTThis paper deals with bulk reagent handling at the Kidd Creek concentrator. The reagent section at Kidd Creek has operated excellently since milling began in 1966. The bulk handling techniques are satisfactory. They have contributed substantially to good working conditions, economical practices and metallurgical efficiencies. The bulk handling features described should be considered in existing and proposed concentrators."

Jan 1, 1970

By R. H. Duval

"In May 1936, Pamour started producing gold by cyanidation of flotation concentrates, and in 1939 was milling about 1, 600 tons per day.Refining records dating from 1939 show two oil-fired furnaces in use, (Rockwell type 46 11 x 29 11 inside oval shell).Refining time averaged 7. 83 hours during the year 1939, indicating a complete refining shift of about 9. 33 hours. That year appears to be characteristic of the period with regard to time required and results obtained.For that year total fineness (gold + silver) of the bars averaged 940 (approx.), but it frequently dropped below this figure, sometimes far below.Furnace lining life varied widely from three to seven or more months. Sillimanite was the standard lining but Mullfrax 41 was frequently used.For many years refining practice remained practically unchanged, and in 1960 procedure still consisted essentially of mixing a flux(% Composition Borax 41, Silica 11, Soda-Ash 11, Nitre 15, Mn02 22) with cyanidation precipitate in the ratio of l. 2 to l and heating to a medium heat (yellowishred, 2000° F) with a low flame for a long time. Time required was about 10. 5 hours per refining. Results were still much as detailed above.At this time it was decided to revise refining procedure, in an effort to shorten refining time and obtain consistently good bullion fineness."

Jan 1, 1965

By S. Koski, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60” x 113"" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns.This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining."

Jan 1, 2012

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy&apos;s resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By F. Moraw

The use of redox fuel cells in which oxygen is replaced by other oxidants such as ferric ions can have significant advantages [1-3]. For example, the cathodic reaction rate (e.g., exchange current density) can be increased by several orders of magnitude compared to the oxygen reduction reaction, and platinum group metal (PGM) catalysts are not required. As a result of the higher aqueous solubility of the oxidant in a redox fuel cell compared to that of oxygen the rate of mass transfer (e.g., limiting current density) is greater by several orders of magnitude. The redox fuel cell can achieve high efficiencies and has other fuel cell advantages. The main issue with the redox fuel cell cathode is the regeneration of the oxidant where low conversion efficiencies are achieved even with platinum group metal (PGM) catalysts. In the work discussed here the Fe3+/Fe2+ redox fuel cell cathode is characterized over a range of electrolyte concentrations and operating conditions, and electrode materials. Cyclic voltammetry and electrochemical impedance spectroscopy are mainly used for electrochemical characterization and mechanistic determination of the cathode redox couple. Further characterization with selected compositions and materials is done in a redox fuel cell (hydrogen - Fe3+/Fe2+). The mechanism and the advantages and disadvantages of the fuel cell redox cathode are discussed with respect to other approaches and other redox couples.

Jan 1, 2005

By Gino Palarchio

Dofasco is Canada?s 2nd largest steel manufacturer producing 4.5 million tons of flat rolled steel per year. They have revenues of over $3 billion and employ 7,000 people in their Hamilton, ON plant. Dofasco is North America?s most profitable steel producer and were recently ranked as the #1 steel maker in the world by Dow Jones. Motivation to Improve In the 1980?s the steel business was good. However, in the late 80?s and early 90?s things began to change. Globalization was beginning to influence the market, imports started arriving at lower prices and higher quality, hangover from the 1970?s inflation saw costs rising and prices dropping, there was a shift from a sellers to a buyers market, and shareholder returns were beginning to erode. Dofasco took a step back and evaluated their maintenance performance and found that they were operating in an environment where 70% of their work was reactive and only 30% was proactive. They also found that the rate of product quality improvement was flat and their average equipment availability was only 78%. At that point they realized that Equipment Reliability was key to improving product quality, production output, costs and shareholder return. They initiated a project to research, develop, and implement the most advanced maintenance practices and information technologies to achieve maximum equipment reliability.

May 1, 2001

By E. Norton

"Even though the subject of this panel discussion is dust control, rather than dwell on the design aspects of dust collection systems which are well documented in numerous publications, :it was considered more pertinent to the present economics of mining to examine the energy costs involved.At the present time, the facts of shrinking fossil fuel reserves and spiralling fuel costs are being constantly brought to our attention. Industry is being motivated to consider the possibilities of incorporating heat recovery systems in areas where they prove to be economical. Unfortunately, it is not a simple exercise to determine if the installation and operation of heat recovery equipment is feasible and economical. Each process involving heat recovery potential must be thoroughly studied in all aspects.In a paper presented at the 1975 Annual General Meeting of the Canadian Institute of Mining and Metallurgy in Toronto, Ontario, entitled ""The Influence of Energy Conservation on Concentrator Design"", it was stated that the largest single energy consumer in winter is space heating with the largest portion of this supplied to crushing and screening plants. (1) Within the scope of this panel discussion we will study, as one example, a crushing and screening plant using natural gas heat in the province of British Columbia and we will explore the feasibility and economics of installing air-to-air heat recovery equipment."

Jan 1, 1976

By Rodolfo Zanella

Au/TiO2 catalysts were prepared by deposition-precipitation using NaOH (DPN) (~3 wt % Au) and urea (DPU) (~8 wt % Au), and calcined at various temperatures between 100 and 400 °C. They were characterized by UV-Visible, XANES, EXAFS and TEM. Their activity were tested in the reaction of CO oxidation at 5°C. After preparation, the gold species are in the oxidic state III. They begin to transform into metallic gold under air at ~100 °C for DPN and ~150 °C for DPU. At 200 °C, all the gold is metallic for the two preparation methods. The particle size increases from 1.5 to 3.5 nm with the calcination temperature. The catalytic activity for CO oxidation increases with the percentage of metallic gold, and it is maximum at 200°C for both types of samples. The activities (per mole of Au) are the same for the two types of catalysts. At higher temperatures, the catalytic activity drops. The decrease of activity is mainly due to a change of particle shape with the calcination temperature rather than to the increase of the particle size. At a calcination temperature of 200°C, the particles present small facets with rounded parts, and their outer surface contains a large proportion of low coordinated sites (steps and corners) while at high temperature of calcination, they are truncated octahedra with smooth facets.

Oct 1, 2003

By Pierre Gy

"Abstract - This paper deals with industrial complexes such as: (1) a mine producing metal-bearing ore and a furnace(s)/converter(s) where the ore is melted into metal, either directly, or after a mineralurgical concentration; and (2) quarries producing the raw materials required for the manufacturing of cement and the kilns to which they are fed.Each mine or quarry operation results from the exploitation of a mineral deposit. This deposit is never homogeneous. The raw materials which are extracted from the mine/quarry can never be safely fed to a "process" such as a cement kiln or a metal smelter, because the devices involved lack the flexibility required to absorb a very inhomogeneous feed. Furnaces and kilns are known to be very sensitive, sometimes dangerously so, with regard to deviations from a certain ideal feed composition.The purpose of this paper is to present the conditions required to optimize the operation of such a complex, so as to maximize the production, the quality of the product, as well as the profit generated. Two key operations are involved: sampling (to know accurately the materials being dealt with) and bed-blending (to achieve the desired degree of homogeneity). The theories of sampling and bedblending have been developed by the author and presented in various books (Gy, 1992, 1998)."

Jan 1, 1998

By D. A. Livingstone

"INTRODUCTORY REMARKS BY PANEL CHAIRMAN - D. A. LIVINGSTONEThe mining industry has progressed significantly from the dusty mines and mills of decades past to the modern processing complexes of today, and improved technology has made great strides in eliminating debilitating lung discuss. More recently, the public's environmental awareness is also working to enforce more stringent regulations and controls in tl1e matter of dust in working places.There are numerous excellent texts and handbooks outlining the principles of collection of dust produced in the various unit operations entailed in the crushing, screening and the transport of ore. However, it is painfully obvious that dust emanating from belt return idlers and scrapers, take-up pulleys, skirting, larger and deeper chutes, clean-up operations, etc., which I choose to refer to as fugitive dust, presents some seemingly unmanageable difficulties, or at least difficulties inordinately costly to correct. Possibly static electricity is adding to the difficulties. In my view, these problems are magnified in many of our B. C. operations where ore from open pit mines in cold climates is frequently crushed in unheated buildings, thereby precluding the simple and obvious use of water sprays for dust suppression.It is hoped that the presentations and discussion which follow will emphasize some of these unusual problerr.s and suggest corrective measures, either tried or planned."

Jan 1, 1976

By U. Troncoso

Mantoverde is a heap leach-SX-EW operation that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has been steadily increased to reach 62,000 ton in 2005. The forecast copper production for 2006 is 60,300 ton for an ore treatment rate of 9.5 million ton. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. Several improvements in the heap leach process have been implemented to cope with the higher ore throughput and copper production. However, the solvent extraction plant has remained unchanged which has resulted in a lower availability of raffinate solution and, as a consequence, in longer leach cycles. Different studies have been undertaken in order to optimize the solution management system at Mantoverde, including column test work aimed to reduce the leach cycle and solvent extraction plant modifications aimed to increase the raffinate solution availability. The test work program and the economical evaluations carried out, as well as the conclusions and recommendations obtained, are discussed in this paper.

Jan 1, 2007

By K. D. Peaslee, J. M. Soto, IéDé Smith, A. D. Saikia

Spinel-forming refractories reduce penetration of metal and slags through a tightening of the lining resulting from the volume expansion associated with spinel formation. Sintered spinel is often added to reduce the overall volume increase that results. Tests were carried out to evaluate the difference between performance in spinel¬forming and spinel-containing refractory mixes. Eight refractory linings, one (1) pure magnesia, three (3) magnesia-base spinel-forming and four (4) alumina-base spinel- containing dry vibratable mixes, were tested for four hours in contact with a low-carbon, low-manganese steel in a coreless induction furnace at temperatures in excess of 1600°C. Afterwards, sample were cut, and wear and penetration were measured. For magnesia-based mixes wear was minimized using 20-30wt. spinel formation although further experiments are required to determine the optimal value. For alumina-based mixes, there seemed to be an optimal ratio of spinel added to spinel formed that minimized penetration and wear at the slag line. Sidewall accretion occurred and the accretion was the highest for the mix with the ratio of spinel formed to spinel added near the optimum value. Therefore to design an optimum refractory mix the benefits of higher ratios of spinel added to reduce penetration and wear at the slag line will need to be balanced with the tendency to form accretions on the sidewalls of the furnace.

Jan 1, 2004