Search Documents

By S. Mostaghel, S. Nicol, M. Y. Solar

Once upon a time, the process engineer developing the design criteria for a new saprolite ferronickel smelter had it easy: most ores were around 2.5% Ni, with a Fe/Ni ratio of 4 to 5 and a SiO2/MgO ratio of about 1.6; to use the French word: garnierites. The ferronickel grade selected was the conventional 20 to 25% Ni and the impurity levels could be predicted from well established [C], [Cr] and [Si] vs (FeO) graphs. However the process engineer can no longer depend on statistics to design smelters: Ni grades are decreasing while the goethite contents are increasing; SiO2/MgO ratios vary from 1 to 3; and Al2O3 concentrations are reaching levels that cannot be ignored. Mechanistic models must be developed to select or predict essential parameters such as kiln and furnace reductions, ferronickel grade, slag losses, metal and slag liquidus, operating temperatures, etc. But these models must be simplified so that they can be used on a routine basis; and they must be calibrated against a wide range of commercial operations in order to yield the most realistic predictions possible. The present paper proposes one possible approach, using FactSage as a basic source of thermodynamic data. The predictions thus obtained are compared to actual performance for two well documented operations, as well as to the predictions made with other tools that might be more accessible.

Jan 1, 2014

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By Cadman S. J

( The central part of the Gippsland Basin is surrounded by existing major Petroleum accumulations and although six exploration wells have been drilled in the area, none are significant petroleum discoveries. Post drilling analyses indicate that the wells were drilled off structure due to the presence of high-velocity Miocene channels. These channels contain carbonates of significantly higher interval velocity than the surrounding sediments. Problems with seismic interpretation were thus encountered in the development of prospects in the central part of the Gippsland Basin as part of a BMR prospectivity study. The seismic interpretation problems associated with the Miocene channels are two-way time pull-ups at the underlying top of Latrobe Group and deeper levels on the seismic sections. Interpreted seismic sections passing through some of the exploration wells and the Miocene channels are presented to illustrate the configurations of these channels and the pullup effect associated with them. Two different methods of depth conversion were applied, one for the area below the high velocity channels and the other for the area away from the channel. The application of these two methods of depth conversion were found to be reasonably successful in correcting for the pull-ups caused by the high velocity Miocene channels. Mapping of the events near the top of Latrobe Group and near Base Lower L balmei seismic horizons has led to the identification of several potential structural closures. Further exploration efforts are necessary in this area to test these closures.

Jan 1, 1992

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

By T. Hadley, E. Catovic

"Northern Minerals Limited’s (ASX: NTU) flagship project is the Browns Range Rare Earth Project (the Project) located in Western Australia, consisting of a number of deposits with high value, heavy rare earth elements, in particular yttrium, terbium, and dysprosium. The deposits are dominated by xenotime mineralisation, which occurs within hydrothermal silicified and hematitic breccias. The Company delivered an initial JORC compliant resource estimate for the Project at the end of 2012 of 10,500 t of contained total rare earth oxides (TREO), which was increased to 28,084t of contained TREO in October 2013 and further enlarged to 47,997 t of contained TREO in February 2014. Concurrent with the growth of the Project resource base, significant progress has been made in developing the metallurgical process for the beneficiation and extraction of rare earth elements (REE’s) from the xenotime mineralisation. Development of the beneficiation circuit evaluated several process options and selected whole-ore flotation and magnetic separation, followed by flotation (hybrid circuit) as the two preferred flowsheets to pilot, following encouraging results on the bench of 83% and 86% recovery to a 20% TREO mineral concentrate respectively. Several downstream hydrometallurgical extraction flowsheets were evaluated. However, the following two preferred process flowsheets were ultimately selected for further detailed investigation during the prefeasibility study: 1. Sulphation bake, water leach, purification, oxalate precipitation, and/or calcination to produce a mixed RE oxide; 2. Sulphation bake, water leach, phosphate precipitation, caustic conversion, HCl leach, and oxalate precipitation to produce a mixed RE oxalate. Excellent heavy rare earth oxide (HREO) extractions (~ 90%) from beneficiation concentrates were achieved on the bench for both circuits, however flowsheet 1 was ultimately selected as the preferred flowsheet to pilot due to lower capital and operating cost. A mixed rare earth oxalate (42% TREO) or oxide (92% TREO) can be produced with low levels of Th and U of 3 ppm and 6 ppm respectively."

Jan 1, 2014

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By Zwaan J, Kepa J

Ok Tedi mine has become one of the major copper producers in the world. In the process of becoming of age, it overcame the challenges of operating in a locality which is young in geological terms, experiences very high rainfall and has a topography which gives rise to frequent landslides. This paper discusses some of the geological, mine and geotechnical engin- eering aspects of the Mt Fubilan ore deposit.

Jan 1, 1991

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010

By R. O. Burt

"Gravity Concentration, the oldest form of Mineral Processing, remains of major importance to the Industry. Current applications of Gravity Concentration are briefly examined.The Paper details one approach to the development of a Gravity Concentration Plant, from laboratory and mineralogical techniques, through Pilot Plant testing, where applicable, to the actual design of the plant.INTRODUCTIONGravity Concentration, once the major method of concentrating minerals has, for much of the twentieth century been regarded, like the dodo bird, as obsolete. However, in more recent years it is enjoying something of a renaissance, and is once again being treated as a useful, economic alternative in the Mineral Processing Engineers' arsenal.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive."

Jan 1, 1984

By G. K. Mann

Fragmentation analysis of blast or crushed rock material is a time-consuming and costly process. During the last two decades, the mining industry has been investigating image-based analysis systems as an alternative to generate fragmentation results. Many image-based techniques and commercial products have emerged during the last few years, and the mining industry has recently begun using these tools for real-time estimation of size distributions. Some existing systems require manual image editing to add or delete edges (or net) before executing the fragmentation analysis routine. This manual procedure may take hours of time for each image analyzed. Reliable and robust image segmentation should be able to handle a wide range of rock textures and sizes under a variety of lighting conditions. This paper describes a novel software application, which has the capability to autonomously capture images and analyze them to generate the particle size distribution. The system can also process a batch of images captured during a fixed duration of time and produce the overall particle size distribution. The new method has different layers of segmentation modules, which allows the system to operate under a wide range of rock textures and lighting conditions. A new grey-level slicing technique is developed which can perform under a range of illuminating conditions. The Canny-based edge detection technique is used to segment rocks appearing in dark regions.

Jan 1, 2006

By Robert E. Mazurak

Mines and plants for sale, downsizing, bankruptcies, consolidation, slab imports, minimill growth displacing traditional integrated steel-making. These are some issues for North American iron ore and integrated steel producers. But the blast furnace still remains the workhorse of the ironmaking industry. And direct reduction and other alternate ironmaking technologies have yet to make any serious inroads in North America. How come? This article addresses the current state of primary ironmaking in the changing North American steel industry, the direct reduction market and new technologies under development that may hold some promise.

Jan 1, 2003

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By Donald Leroux, Jean-François Wilhelmy, Ahmed Bouajila

"A young private R & D organization, COREM celebrated its 10th anniversary in 2009. Managed by a consortium of nine mining and metallurgical companies, COREM has the mandate of increasing the competitiveness of its member companies through the development and transfer of mineral processing innovations. Typical technologies developed by COREM include alternative mineral processing techniques, novel operating strategies, innovative sensors and process simulation software. Many of them were developed in partnership with universities and selected research organizations.Because the COREM membership base is broad (from ferrous to base, to precious metal industries), its R & D program must deliver technologies with applications within a wide spectrum of mineral processes. Comminution, physical (gravity and magnetic) separation, flotation, cyanidation, pelletizing and thermal processes are the main topics of the R & D program. A number of new technologies have been developed and transferred to the plants of member companies. These examples of transferable technologies demonstrate the capability of COREM to impact the bottom-line of its member companies.INTRODUCTIONCOREM is a private mineral-processing R & D organization that operates from its own laboratories and pilot-plant with its own staff of professionals and technicians (about 95 persons). It is managed and financially supported by a consortium of nine mining and metallurgical companies and three provincial and federal ministries. The very ‘down-to-earth’ mission statement of COREM is to increase the competitiveness of the mineral processing plants of its members. The eighteen plants upon which the COREM technology development program is currently based can be found in Québec, Newfoundland and Labrador, New Brunswick, the Netherlands and Botswana."

Jan 1, 2010

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

When the 2008 Olympic Games begin in Beijing, China is September it will not only mark the end of the journey for the Olympic torch and the thou-sands of participating athletes, but the games will also mark the culmination of a massive amount of construction in the city. On display for the world to see will be 31 new and refurbished venues including the 91,000-seat National Stadium called the ?Bird?s Nest? and the aquatics center, called the Water Cube. What will not be featured as prominently on the television cameras broadcasting the games around the world will be the network of tunnels built beneath the city. But that infrastructure of rail lines will be of critical importance to the games. While preparing to host the world, China added a subway tunnel that will include four stops in the Olympic Park. The 4.4-km (2.7-mile) subway line that runs through the complex of stadiums, gymnasiums and parks began trial operations in June. Prior to the opening of that line, Beijing's No. 5 subway line, which runs through the heart of the city from north to south, opened in October. That 27.6-km (17-mile) line took nearly five years to build and includes 23

Jan 1, 2008

By A. J. Vivyurka

"This is a talk about the experiences that Rio Algom Mines Ltd. has had in the Elliot Lake uranium area trying to make the tailings more compatible with the surrounding environment. To get a better idea of the problem that we are associated with we have to go back to the location. The Elliot Lake uranium area is situated about half way between Sault Ste Marie and Sudbury and is about 20 miles north of Lake Huron. In 1950, uranium was discovered along the north shore of Lake Huron and by 1961 we had up to 9 mines operating in the area. Then the United States Atomic Energy Connnission withdrew their contracts so that at present there are only 2 mines operating. From all the mines that we had operating, we ended up with 7 tailings areas. From these 7 tailings areas we have 5 sites where we have active treatment or rehabilitation. There is the Pronto site where we are treating uranium tailings and copper tailings. There is the Lacnor-Nordic site which is located just out of Ellio Lake. The Milliken-Stanleigh site is in the Crotch Lake area. The Panel tailings is off the north end of Quirke Lake and finally there is the operating property of Rio Algom Mines at Quirke Lake.To understand fully the problem with this rehabilitation we have to look at the constituents of the ore. The ore body is a quartz conglomerate with uraninite and brannerite as the uranium bearing minerals in a fine ground mass of quartz, sericite and pyrite which separates the larger quartz pebbles. The approximate composition of the ore is: 80% quartz, 13% chlorite, 7% pyrite and 0.2% uranium minerals. The processing method also adds a few constituents to the final tailings."

Jan 1, 1975

By Z. W. Nkosi, M. Sephton, J. H. Potgieter

The exhaust system is a complex assembly of various components performing important tasks in harsh environments. Carbon steels have been used extensively in exhaust systems, but pressure for lower cost, increased fuel efficiency; lower hazardous emissions, weight savings and increased life expectancy have shifted the emphasis to stainless steels. In response to the growing consumption of stainless steels in automotive exhaust systems, the need to properly evaluate their corrosion resistance properties in order to ensure their appropriate use, has increased substantially. This paper evaluated the most common corrosion and oxidation tests developed that are used and applied it to four common stainless steels often employed in hot end exhaust components. In a summary considering the weight loss of an alloy, it general corrosion rate and pitting resistance under all the test conditions for hot end exhaust components, results indicate that 434 was by far the most corrosion resistant alloy, followed by 1.4509 and 321, and lastly 304 was the least corrosion resistant. In general, the ferritic stainless steels, especially 434, outperformed the austenitic ones under all the test conditions.

Jan 1, 2006

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004