Search Documents

By B. Unver

Effective strata control is a prerequisite for maintaining an efficient mining operation. If the strata in the vicinity of an opening are not controlled effectively, it is impossible to perform a safe, efficient and economical operation. In this paper, the reasons and outcome of instability problems observed in roadways opened in clay and marl at the Bolu Colliery of Yeni Çeltek Establishment are investigated. Roadways under examination were located in a syncline causing high residual tectonic stresses. Factors affecting the instability have been studied thoroughly by examining geology and tectonics of the area, establishing convergence measuring stations to understand in situ behaviour of supports and laboratory tests to determine engineering properties of samples taken from nearby convergence measurement stations. As a conclusion, a new production strategy and a new support system are recommended to maintain stability.

Jan 1, 1999

By Tony A. Rorke, Joe R. Brinkmann

The application of instrumentation to better understand and improve production blasting is one of the most fruitful areas of explosives and blasting research. The majority of instrumented studies of production blasting have relied on the extrapolation of far field measurements to postulate blast performance in regions of interest closer to the charge where rock breaking takes place. However, the nonlinear and dissipative nature of the quantities being measured raises serious questions as to the accuracy and validity of such extrapolations.

Jan 1, 1991

By Chas. E. van Baraeveld

"The information presented in this report is a by-product of studies concerning zinc, and is published in response to various inquiries for information as to the suitability of zinc for roofing. It parallels a previous report of the Bureau of Mines on slate roofing.Available Forms of Zinc RoofingZinc is available for roofing in three forms: 1. As sheet zinc which may be used advantageously on roofs with as flat a pitch as 1 in 4; laid with standing seam construction for small roofs and with batten construction for large roofs. 2. As corrugate sheets, in widths up to 40 inches and in lengths up to 8 and feet, available for siding and roofing in industrial buildings (with certain re¬strict ions) and or farm buildings (without restrictions). 3. In the form of shingles.Advantages of Zinc Roofing1. Zinc is a permeant roofing material; that is, when suited to the conditions, and properly applied to a roof designed with the right purlin spacing it will outlast the building and still have a salvage value equal to a least half the original material cost. It is applicable to a wide range of conditions, from the most expensive to the cheapest type of construction, and is not greatly above the cheaper materials in first cost. A permanent roof of simple outline need not cost over $15 to $25 per square (100 square feet), depending upon the method of construction required a corrugated sheet roof for industrial purposes or for farm use need not cost over $15 per square for ordinary conditions. 3. Corrugated zinc sheets have the distinct advantage of being available for re-use and re-construction if handled with ordinary care. 4. Zinc oxidizes to a certain point, building up a strong protective coating which in time effectually checks further oxidation; thus it does not oxidize to the point of destruction as steel does, 5. It is light and easily handled."

Nov 1, 1924

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905

By M. M. Tilman

Etchants containing hexavalent chromium and sulfuric acid are used in a variety of surface-finishing operations. When the resultant spent solutions are discarded, substantial quantities of chromium are lost and pollution prob¬lems are created. To minimize the undesirable environmental effects while improving metal and minerals recycling technology, the Bureau of Mines is con¬ducting research on a method for the economic inplant recycling of these waste etchants. Trivalent chromium, produced when the etchant reacts with a substrate, is oxidized in the anode chamber of a diaphragm cell; other metals, dissolved during the etching operation, are transferred to the catholyte. When waste brass etchants are treated in this manner, all of the trivalent chromium is oxidized and more than 40 percent of the copper and zinc is removed. Similar copper removal and chromium oxidation are achieved with waste printed circuit board etchants and rinse waters from plastic etching operations. The electrical energy needed to regenerate 1 kg sodium dichromate is less than 9 kwhr. Regenerated brass etchants evaluated by two companies equaled or exceeded the performance of fresh etchants.

Jan 1, 1979

By V. Coetzee

In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes. Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum.

Jan 1, 2006

By J. C. Fowler

[This i.untra t hds bmii III c'IIILt fur till- past 1':?:u yrlr;, Till-- wurir pnrfor rw:it '. ,JS hlui.rn dawn Ilttf lit Iu i eel i ih?IS( S. 1 hesrt aIII, Phase I Candor tlri I a lest It) donurnSlrale SeiSrrlir nurihudS to hu USi!d lot ttlr? rti?tei thin and Iu" ainnl ul trapped rrlinc:rs hitting (-)it the roof with a harnrner, Phase I' Design and cunStrur.t a permanent Seismic monitor System to rrlunrtur roof (ails arm r:xploslun', III ,r 'Vol king mine. Phase III - Ire dII an an i i irr for sVstl rtl Ii i`'Smltur air quality in till, niitii iiH II ? ir,iti tin; niln !III ;I I ,, i; Phase I V - Conduct 11(21 d tests of the seismic IT IUnit UT ieq system fur a period nl two 11IUIIIIIS. Phase, V - Condirct three test periods of the seismic system over a period of six mimilis. Detailed reports covering the wurk. done in Phases I, 11, and IV have been i : . r tr I - i t report will, therefore, cuni.entrate on the work perfurmed in Phases III anti V.]

Jan 1, 1975

By J. Duncan Crone

"A test surface Pulse EM(PEM) survey over a plunging massive sulphide lens, located in the Snow Lake area of Manitoba, has shown that it is possible to detect the body to a depth of 300 metres. Another surface survey in the Athabasca basin of Saskatchewan, clearly outlined a large, basement graphitic zone below 450 metres of sandstone cover. Deep detection of these conductive bodies was achieved by energizing large volumes of ground with a strong transmitted EM field. Such large fields also energize all other conductors present in the exploration area. Both of the above survey results indicate that more than one conductor is present. In such cases, detailed field coverage is required for accurate interpretation, and interpretational procedures that assume simple geometrical shapes should be applied with caution. In all cases geological and geophysical information should be coordinated in detail. The first test drill hole still has a high risk of missing the deep conductive body and two or three holes should be budgeted per target.Borehole Pulse EM surveys are now routinely used to help zero in on deep conductive targets. They are also proving effective in development drilling programs by outlining the edges of conductive bodies. The results of surveys from northern Quebec illustrate how they may provide more accurate shape and tonnage estimates."

Jan 1, 1985

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

By S F. Simmons

The Ohaaki Rhyolite and the Rautiwiri Breccia are two volcanic units occurring in the shallow and deep parts of the Broadlands-Ohaaki geothermal system. Alteration of these units by chloride waters results in distinct mineral assemblages that also have distinct whole rock compositions. The Ohaaki rhyolite is altered to an assemblage dominated by quartz, adularia, illite and pyrite as a consequence of silica, potassium and sulfur metasomatism. Locally, these rocks contain up to 0.5 ppm Au. The Rautiwiri Breccia by contrast is altered to an assemblage dominated by albite, adularia, quartz, illite, chlorite and pyrite in association with modest sodium metasomatism. Whole rock oxygen isotope compositions of altered rocks range between 3.3 and 7.5 ë, and are generally lower compared to their fresh rock equivalents having values of 9.5 to 10.6 ë; the result is broad pattern of lower values with increasing alteration intensity.

Jan 1, 2002

By Thompson D. R, Milton R, Perry K. M A

From the Department for Research in Industrial Medicine (Medical Research Council), The London Hospital; and the De Havilland Aircraft Company:M.R.C. INVESTIGATIONS IN 1936In 1936 the Industrial Pulmonary Disease Committee of the Medical Research Council investigated both clinically and radiologically a group of fifty workers who had been exposed for a number of years to the inhalation of alumina in the reduction factory of the British Aluminium Company. The results are shown in Table 1.They also considered the sickness records of all the workers (Hill, 1936), as compared with those in other parts of the factory (Table 2).

Jan 1, 1945

By J. B. Gayle

Commercial flotation plants operate on a continuous basis that is not simulated closely by the batch testing methods widely used in Bureau of Mines laboratory studies of flotation, Batch methods indicate whether a particular separation is possible but provide little or no information about the rates at which such separations can be effected in continuous operation, Therefore, laboratory equipment suitable for testing on a continuous basis was assembled for an investigation of a number of the operating variables that influence the flotation of coal. The results of these tests lead to the following conclusions: 1. Flotation recoveries were markedly influenced by variations in the percent solids in the feed, However, the relation between these variables is complex and depends on the particular coal and operating conditions used. Flotation rates generally increased with increased cell concentrations.

Jan 1, 1962

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983

By Emmanuel Portilllos

Every paste backfill system is typically unique, this being due to the particular tailings characteristics, the backfill recipe and requirements of mine planning. Key to successful transport to the underground workings through the boreholes and the distribution pipelines is the quality of cemented paste, being free of lumps and recipe components uniformly mixed. Certain types of mixer require that the mixing environment is required to be intensive as possible. In this sense, the present paper point out some of the general aspects of paste plant design, a short discussion on paste recipe and process equipment, followed by a technical comparison between a batch mixing and a continuous mixing process, currently applied to the production of cemented paste tailings for mine backfill.

Sep 9, 2007

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

By Larry G. Stolarczyk

Jan 1, 1980

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004

By Carl R. Peterson

[In lTI n,v und I'gr'oun nllnin~ Opt'I'ali n' the high . t cost is the loading and I 3ulage of t tln-of -D"'line ot'. 01' hauling costs can be r duced signifi-cant\v with the us ~ (r \) >It corn'e)'OI' " a COnlTllOn pl'acti c i.n coal and other s 0 t'L rn I n r' a l III i, n e , '. Jf 0 vel s i z ' () f' e can bee 1 i 11.11 tl ate I rH'i 0 I' lO C n v e . in g, ]

Jan 1, 1976