Search Documents

By A. N. Holden

A DISLOCATION mechanism has been described by Cottrell' by which metals can yield locally, I. form Liiders bands, giving rise to a characteristic stress-strain curve with a sharp yield point and appreciable strain at constant or decreasing stress. It is undoubtedly the best mechanism that has been suggested to date." In its present development, however, the dislocation mechanism provides a more satisfying explanation for the sharp yield point than for the extensive localized flow occurring at the lower yield stress. The primary objective in this paper is to extend the dislocation mechanism to account for localized cataclysmic flow by a dislocation collision process and to give experimental evidence to support such a process. Only the yielding of iron containing carbon -will be discussed, although other metal-solute systems are known to behave similarly. Cottrell Mechanism In brief, Cottrell explains the yield point in the following way: The dislocations in iron which must propagate to produce slip usually lie at the center of local concentrations of carbon atoms, since segregation about these dislocatlons relieves some of the local stress resulting from them. A dislocation surrounded by a "cloud" of carbon atoms is thus anchored, and a higher stress is required to set it in motion than to move a free dislocation. Considering all available dislocatlons to be anchored in this fashion, the iron exhibits a yield point when the first dialocations break free and move through the lattice causing slip. This first breaking away of a dislocation enables other dislocations to break loose by "interaction" and the process becomes a cataclysm producing local deformation or Luders bands. The yield point in the stress-strain diagram for iron is absent in freshly deformed material, but returns gradually with time; the phenomenon is one aspect of what is called strain aging. The rate at which the yield point returns following straining depends on the temperature of aging. According to Cottrell the rate of return of the yield point in strained iron is limited by the rate of diffusion of carbon at the aging temperature, the mechanism is onr: of reforming the solute atmospheres around carbon-free dislocations that had stopped moving coincident with the removal of stress. If the specimen is retested immediately after straining and unloading, carbon will not have had time to diffuse to, and re-anchor, dislocations and the yield point will not occur. The carbon diffusion limitation for the rate of strain aging apparently applies if the criterion for strain aging is either the change in hardness" or the change in electrical resistance" of the strained speci- men with aging time. The possibility exists, however, that the yield point actually returns to strained iron at some rate other than that deduced from hardness or electrical resistance data. Therefore, as a preliminary experiment, the rate of yield point return in a rimmed sheet steel strained 6 pct in tension was measured at 27°, 77°, and 100°C. A plot of yield-point elongation for each of these temperatures against aging time appears in Fig. 1. The aging process is described by curves which rise to a plateau value of elongation that seems independent of temperature, but at a rate that depends on temperature. Very long times lead to a further rise in the yield-point elongation above the plateau value. However, if the later increase in yield-point elongation is ignored and the log of the time to reach half the plateau value of elongation is plotted against 1/T, a straight line results for which an activation energy of about 25 kcal pel- mol may be assigned. Within the accuracy of this sort of experiment this is approximately the activation energy for the diffusion of carbon in iron (20 kcal per mol), and the carbon diffusion limitation suggested for the yield-point return on strain aging is valid. The Cottrell mechanism thus explains in a qualitative manner the occurrence of a yield point in iron and its return with strain aging. It fails, however, to explain some of the other experimental observations that have been made of the yielding behavior of iron. For example, it is known that the yield point in iron becomes less pronounced with increasing grain size. Annealed single crystals of iron have very small yield-point elongations .if indeed they have any,' compared to a polycrystalline steel. If the only requirement for a yield point is that the dislocations in the lattice of the annealed. material be anchored by carbon atoms, the difference in the behavior of single crystals and polycrystals is not explained. That a dislocation mechanism may be entirely consistent with little or no yield point in an annealed single crystal will become apparent later when dislocation interaction is discussed. Strain aging produces a definite yield point even in single crystals. This accentuation of the yield-point phenomenon in single crystals after strain

Jan 1, 1953

By F. M. Drake

IN this paper I propose to describe a plant which I lately erected for the Mount Stewart Lead and Silver Mining Company of Leadville, New South Wales, Australia. I am indebted to Mr. W. F. Burrow, of the Roads and Bridges Department of New South Wales, for the drawings which I present herewith, he having reduced and assembled them from my working drawings. The works are situated on a sloping hillside, but sufficient fall mas not available to have the furnace as high as desired, and at the same time have a good slag-tip and sufficient depth on the ore-floor to store a supply of ore and flux. The ore is delivered on the ore-floor (which is of the full width of the furnace-building, and extends back into the hill a distance of seventy feet) by two overhead tramways (not shown in the drawings), one on each side. From these the ore-mixture is made up on one side, while it is being taken to the furnace from the other. The fuel also is delivered by these tramways. The fluxes are stored on a floor directly at the back of the boiler and engine room. The boiler is a Cornish one, 6 feet 6 inches in diameter by 25 feet long. Its flue is 3 feet in diameter and does not contain Galloway tubes. The working-pressure is 40 pounds per square inch. The engine is an old-fashioned one, with a cylinder 16 inches in diameter by 30 inches stroke. Both the engine and boiler had been part of the plant of a defunct gold-mining company. They were very extravagant in their consumption of fuel. The blast is supplied by a rotary pressure-blower, of the Baker pattern, made in England. It has a capacity of 60 cubic feet per revolution. The furnace, which has several novel points, is shown in detail in Figs. 1, 2 and 3. The jackets are of cast-iron, and are higher than those generally used. They are different, too, in that the feedwater inlet is through a hand-hole plate near the bottom. This plate is fastened to the jacket by stud-bolts, and is provided with a baffleplate, which prevents the cooling water from impinging against the inner plate. The outlet is by a goose-neck at the top, which dis-

Jan 1, 1893

By Thomas M. Drown

The use of bromine as an oxidizing agent, particularly for sul phur, has become very general in analysis, replacing the stronger oxidizing acids. The object of this paper is to describe briefly the experience which we have gained with this reagent in the laboratory of Lafayette College in the oxidation of metallic sulphides. Most of the simple sulphides, as blende, pyrite, etc., when exposed to the combined action of an alkaline hydrate and bromine, and finally to hydrochloric acid, are completely and promptly dissolved. The procedure is as follows: The very finely pulverized mineral is first treated, in a beaker, with a solution of sodium hydrate of a spe cific gravity of 1.25, and heated ; bromine is then cautiously added to supersaturation, and finally hydrochloric acid to acid reaction. If any of the sulphide is not taken up, the same operation may be re peated. It is necessary, however, that the mineral be very finely pulverized. Instead of using the pure bromine, a saturated solu tion of bromine in potassium bromide may be used with equally good effect. The process is advantageously simplified by making a saturated solution of bromine in the concentrated alkali. This is done by pouring bromine into a solution of sodium hydrate, of the above given specific gravity, until no more is taken up, and then adding a little of the sodium hydrate solution until the liquid does not give off free bromine. The procedure with this solution is as follows: The pulverized mineral is moistened with, say, 10 cc. of the solution, and heated, then hydrochloric acid added to just acid reaction. Two more additions of the alkaline solution, in amounts of 20 cc. each, are added at intervals of about ten minutes, each addition being followed by hydrochloric acid. The total amount of the alkaline solution (containing the bromine) used is, therefore, 50 cc., and the amount of hydrochloric acid should not exceed that necessary to make the solu tion acid after each addition of the alkali. The mixture should be kept hot. After the final addition of acid, the contents of the beaker is taken to dryness and heated in an air-bath to 110° to 115°C., to render silica insoluble. The dry mass is then taken up by hydro' chloric acid and water and, after filtration, the sulphuric acid is pre

Jan 1, 1880

By Jun Hino, P. G. Shewmon, P. A. Beck

THE investigations of Crussard,' of Guinier and Tennevin,' and of Dunn and Daniels," indicate that the subgrains formed in a cold worked and annealed metal are capable of growing at each other's expense during annealing, if the temperature of annealing is sufficiently high and the time is long enough. The results of Dunn and Daniels are particularly convincing in showing that subgrain growth is essentially the result of the free surface energy associated with the subboundaries. In subgrain growth, as in ordinary grain growth, energy is gained as a result of the decrease in total subboundary surface area per unit volume. Recently, Wood and Scrutton4 found that the rate of subgrain growth upon annealing increased very considerably, if simultaneously a creep strain was applied to the specimen at a low strain rate. Working with 99.98 pct pure fine-grained aluminum, these investigators found that the continuous X-ray diffraction back-reflection rings of material strained at room temperature remained continuous after heating for ten days at 250 °C. However, when heated at the same temperature under a stress of 1000 psi even for only three days, the formerly continuous X-ray diffraction rings broke up into numerous dots, which were fairly clearly separated from each other. The continuous X-ray diffraction rings were interpreted as indications of a very small subgrain size, not resolved by the X-ray diffraction method used. The breaking up of the continuous X-ray diffraction ring during annealing under stress was taken as an indication of a great increase in subgrain size, so that the individual subgrains could then be resolved. The effect of simultaneous strain at a low strain rate in accelerating subgrain growth, discovered by Wood and Scrutton and designated by them as "cell growth," is of fundamental importance. The experiments described in this note were carried out in order to confirm Wood and Scrutton's results by direct metallographic observation. Also, information was sought as to the minimum creep strain necessary to produce this effect. A fine grained high purity aluminum strip was prepared by alternate 33 pct rolling and annealing treatments for 1 hr at 350°C. Specimens cut from this strip were subjected to a relatively fast creep strain of 7.2 pct in 3.5 min at 300°C under a constant load initially corresponding to 1185 psi. The subgrains set up were large enough (about 0.015 to 0.03 mm) to be clearly observed (Fig. 1) at X200 magnification with polarized light, after electrolytic polishing and anodic etching, producing a fine oxide film." The corresponding X-ray diffraction pattern is shown in Fig. la. After the fast creep strain treatment a portion of the specimen was subjected to a creep strain of 8.3 pct in 44 hr at 350°C under a constant load initially corresponding to 320 psi. Another portion, annealed under the same conditions, but not strained, served as control specimen. The subgrain size of a typical area of the specimen annealed under strain and of the one annealed without strain is shown in Figs. 2 and 3 (X-ray diffraction patterns, Figs. 2a and 3a). Annealing without strain produced clearly observable subgrain growth (subgrain size: about 0.03 to 0.05 mm). The effect of simultaneous strain was to increase greatly the rate of subgrain growth (resulting in a subgrain size of approximately 0.05 to 0.13 mm), in accordance with Wood and Scrutton. In another experiment, the effect of the amount of simultaneous strain was studied. The initial subgrain structure was set up by fast creep, as described previously. The specimen was then heated at 350 °C under a constant load initially corresponding to 320 psi, as above, for 2.2 hr (0.24 pct strain), and 8.8 hr (0.58 pct strain). Comparison with the corresponding unstrained control specimens by means of X-ray diffraction showed that 0.58 pct strain definitely had an effect, but the effect of 0.24 pct strain was doubtful.

Jan 1, 1953

By W. L. Phillips

Stress-train curves were obtained for single crystals of silver, Ag-5 pct Zn, Ag-10 pct Zn, and Ag-20 pct Zn tested in tension and shear at 78°, 195°, and 297°K. At room temperature the critical resolced shear stress gC increased, the length of' the easy-glide region increased, and the rate of' work hardening dwving easy glide decreased with increasixg zinc concentration. The change in the ratio of uc at room temperature to that at lower temperatures was significantly greater for the alloys than for pure silver. It was found that an increment in stress was necessary to continue slip when the slip direction was rotated 60 deg. The magnitude of this increment increased with strain for all alloys, increased with zinc concentration for a given strain, and for a given strain increased with decreasing -temperature. DESPITE its practical importance in improving the mechanical properties, alloying is not fully understood. Except for copper alloys few sets of systematic data are available. Von Goler and Sachs' studied the deformation of Cu-Zn alloys of increasing zinc content and found that, for dilute alloys, the critical resolved shear stress increases linearly with concentration. The range of easy glide was found to increase with increasing zinc content. Schmid and seliger,2 Sachs and Weerts,3 and Osswald4 have shown that with Mg-A1, Au-Ag, and Cu-Ni crystals, respectively, the critical resolved shear stress also varies linearly with concentration. More recently, Linde and his coworkers have investigated the variation of the critical shear stress of copper alloyed with tin , antimony, indium, germanium, silicon, nickel, and gold. They found that the slope of the critical resolved shear stress is related to the change of lattice parameter with composition, and also to the difference in Goldschmidt's atomic diameter between solvent and solute atoms. Garstone, Honey-combe, and creetham6 have shown that similar relationships can be found for small additions of silver, gold, and germanium to pure copper. They found that, with increasing silver or gold concentration, the critical shear stress for glide is increased by alloying, and so is the range of easy glide, which reaches as much as 60 pct for 0.50 pct Ag alloy and 0.62 pct Au alloy, as compared to 6 pct for pure copper of similar initial orientation. They also found that the alloying additions had little effect on the rate of hardening during easy glide, the slope scarcely changing with increasing alloy content. General secondary slip was detected only when the crystals began to harden rapidly. Although the slip appeared to be very fine in the early stages of deformation, coarser slip bands were formed towards the end of the extensive easy-glide range. The present investigation describes the deformation characteristics of single crystals of Ag-Zn containing different concentrations of zinc. Tension and shear testing were used for this study. EXPERIMENTAL PROCEDURE The method of growing the single crystals, sample preparation, and method of testing have been described in detail previously.' EXPERIMENTAL RESULTS A) Tension-Room Temperature. The initial orientations and stress-strain curves of single crystals of silver, Ag-10.0 pct Zn, and Ag-20.0 pct Zn are shown in Fig. 1. It is evident that there is considerable change in the stress-strain characteristics as a function of zinc concentration. The effects of zinc concentration on the critical resolved shear stress for both CU-zn8 and Ag-Zn alloys are summarized in Fig. 2. At all concentrations the resolved shear stress of the Cu-Zn alloys is higher than that of the Ag-Zn alloys. The resolved shear stress increases parabolically as a function of composition for both alloy systems. The length of easy-glide region increased with increasing zinc concentration, Fig. 3b). As the length increased the slope (do/de) decreased slightly, Fig. 3(b). Metallographic investigations demonstrated two significant effects of increasing zinc concentration. First, the amount of clustering increased, compare Figs. 4(a) and (b). The slip lines changed from uniform in pure silver to clustered in the Ag-20 pct Zn and Ag-30 pct Zn alloys. Second, the amount of cross slip decreased as the amount of clustering decreased.

Jan 1, 1968

By C. S. Matthews, P. Hazebroek, H. Rainbow

It ha been suggested that lormation fractures created by well stimulation treatments will adversely affect sweep-out efficrency in injection operations. Fluid-flow model studies involving vertical fractures of various lengths and fluid systems of various mobility ratios have been carried out to study this subject. In addition, limited data have been obtained on one model containing a horizontal fracture. It was found that relatively long and highly conductive fractures (not generally obtained fracturing operations) were required to affect the sweep-out efficiency substantially. In a given case in the field an approximate distinction can be made between the presence of long conductive fractures and shorter or less conductive ones. This is done with pressure build-up analyses along with data on the relationship of fracture length and conductivity to well productivity. This type analysis shows that usually the fractures induced are either short or of limited conductivity and therefore do not damage sweep-out efficiency. INTRODUCTION Improved well productivity and in-jectivity can frequently be exploited in injection operations. Higher total throughput can yield improved economics. On occasion, the achievement of an increased productivity or injectivity in specific wells can bring about a more uniform sweep of the reservoir. Higher rates can be exploited particularly in water floods of "depleted" reservoirs where a rapid "fill-up" is desired and where low pressures contribute to low well productivity. The creation of fractures local to the wellbore is an excellent means for achieving these objectives. Even though fracturing has been employed in some floods with success,1"3 there still seems to be some reluctance to employ this tool for fear of undue damage to the flood pattern and ultimate recovery. We therefore need to examine the influence which fractures of varying length may have on flood performance and then determine the length of fractures which obtain in the field with conventional fracture treatments. A substantial influence of fractures on the recovery obtained at breakthrough of the injected fluid has been presented by Crawford and Collins for equal fluid mobilities for the line-drive pattern.4,5 In addition, the influence which a fracture has on the production performance after breakthrough and on the ultimate recovery warrants consideration in reaching a conclusion concerning the use of induced fractures in flooding operations. This report presents this type of data for the five-spot injection pattern for several fluid mobilities. In arriving at some conclusion concerning the fracture lengths obtained in field operations we must examine the performance characteristic most affected by the fracture. This is the change in the flow system as reflected in the change in productivity and pressure build-up behavior. A study of these changes is also presented in this report. RESERVOIR ANALOGS The X-ray shadowgraph technique, employing miscible displacement in porous models, has been used in the study of the influence of fractures on pattern sweep-out efficiency. The X-ray shadowgraph procedure is described in detail in an earlier report8. Fractures were represented by leaving the proper portion of the model surface exposed to either injection or production. This assumes the fracture resistance to be negligible compared to that of the formation. Actually the flow resistance in propped fractures obtained in the field is sometimes not negligible so that the results with this model indicate the maximum influence of the fracture. Two types of models were necessary to represent vertical fractures in a five-spot flood. These pattern elements are illustrated in Fig. 1. In studying the influence of the horizontal fracture, only one well spacing length to thickness ratio of 50 was used. The pool unit of a Carter Electric Analyzer was used in studying the influence of fractures on productivity and build-up behavior. The square drainage system of a well was represented by a network of 576 elements of equal volume and resistance. One-fourth of this drainage area was studied as a model unit using a network of 144 condensers and resistors. Vertical fractures were represented by a shunt directed from the well perpendicular to the drainage boundary. Horizontal fractures were represented by a circular shunt. Resistance of a shunt was varied in representing different conductivities for the fractures. FRACTURE DIRECTION AND LENGTH The direction at which a vertical fracture extends into the formation and its length and conductivity influence the sweep behavior. The two

By W. A. Walker, G. W. Ostroot

An increase in the number of deep wells being drilled where extreme bottom-hole temperatures are encountered, and the anticipated drilling of wells where temperatures in the range of 500°F or higher may occur, has brought about a comprehensive investigation of cementing materials and of the techniques involved in their proper usage at these elevated temperatures. Included are developments in cements, retarders, weighting materials and other cement additives which make it possible to formulate a variety of compositions to help resolve the cementing problems of these extreme well conditions. The problems associated with the selection and testing of cements are discussed, and a resume of field results is included. Previous studies on strength retrogression indicate that caution should be exercised in the selection of a cementing composition for use in high-temperature wells. It now appears that, by the addition of silica flour as a stabilizing additive to certain cements, compositions covering a wide range of slurry densities can be designed to meet extreme well conditions without strength retrogression. Improvements in cement retarders make it possible to produce a four-hour thickening time at static temperatures up to 500°F. This temperature is considerably higher than conditions presently being encountered in drilling and completion work. Inert weighting materials, used to produce 20-lb/gal or heavier cement slurries, are reviewed. INTRODUCTION As the search for oil continues, the number of wells being drilled to depths of 10,000 ft or below has continued to increase over the past decade. During 1959, there were 50,893 wells drilled in the United States for a total of 209 million ft of hole. Of this total, approximately 4.45 per cent were drilled below 10,000 ft and 0.30 per cent below 15,000 ft, with a record depth of 25,340 ft recorded (Table 1). With the drilling of this record-shattering hole comes the question, "How deep can wells be drilled?".' Limitations with respect to equipment (surface and subsurface), cementing materials and techniques would cause some concern; however, a panel of experts have agreed that the U. S. oil industry has the equipment and know-how to drill a 50,000-ft hole. The greatest deterrent would be the 700°F temperature they would anticipate encountering at this depth. Although the number of wells drilled under what is generally considered hot-hole conditions (230°F and higher) has been relatively high, each well often presents distinctly individual problems and requires separate consideration and selection of special materials, techniques and equipment. At the present time there are over 30 additives and special cements available for use in "tailoring" a cementing composition for a specific well. It is not uncommon to use three or four different additives with the basic cement to produce the desired slurry characteristics. A generally accepted procedure is to make laboratory tests on selected cementing compositions prior to pumping them into wells deeper than 12,000 ft, or where static temperatures are in the range of 260°F or higher. In some instances, it is recommended that laboratory tests be made where less severe well conditions are encountered. Prior to selecting a cementing composition for a particular well, key personnel representing the operator, drilling contractor and service company should meet to determine that each individual is acquainted with every detail which might influence cementing results and to discuss the execution of the job. For cementing hot-holes, a number of factors must be evaluated before proceeding with the operation. Consideration must be given to the following. 1. Thickening time—The slurry must remain fluid for a sufficient length of time to allow displacement down the casing and up the annular space in a primary cementing job or, in squeeze-cementing, adequate thickening time for both the build-up of a satisfactory squeeze pressure and the reversing out of excess cement. The thickening time of standard retarded cements will often be too short under extreme temperature conditions, thus involving special formulations and requiring laboratory tests to determine the proper amount of additional retarder to obtain the desired pumpability.

By Harlan W. Nelson, James B. Purdy

A study of data obtained during laboratory tests to determine the suitability of bituminous coals for use in residential underfeed stokers of the clinkering type has led to the following general conclusions: 1. Performance data obtained during the test furnish useful and practical information upon which to judge the performance of stoker coals. 2. Conclusions derived from the results of evaluation tests are in general agreement with use experience of the coals in the field. The method is of practical use in this regard. 3. Few direct relationships were found between data furnished by the evaluation test and determinations by standard laboratory tests. This is particularly true with regard to coke formation and clinker formation, two of the most important factors in determining the degree of satisfaction to be obtained in applications of the small underfeed stoker. It has not been the intention in this paper to prescribe this evaluation test as the best method for the evaluation of coals for use in residential stokers. That there are other test methods having similar objectives serves to point out the necessity for full-scale laboratory tests. At the present time, a standard test procedure for the evaluation of coals for use in residential stokers is not available. For the past several years a joint committee, appointed from the membership of the Residential Stoker Committee of Bitulninous Coal Research, Inc., and from the Engineer- ing and Research Committee of The Stoker Manufacturers Association, has been working to develop a standard procedure for testing and evaluating bituminous stoker coals. This procedure has been completed to the extent that it has been drawn up in tentative form. It is now planned to install the equipment in several laboratories and to run check tests, using portions of identical lots of coal, to determine the degree of reproducibility offered by the method. Completion of this standard test procedure should greatly facilitate the evaluation of coals for use in residential stokers. Acknowledgments The cooperation of coal operators sponsoring the coal evaluation tests, in granting permission to use data and results from their tests, is gratefully acknowledged. Acknowledgment is also made to Carroll F. Hardy, Chief Engineer, Appalachian Coals, Inc., for his interest and timely suggestions on the preparation of this paper. Special thanks are due to Ralph Sherman, Assistant Director, Battelle Memorial Institute, who was largely responsible for development of the evaluation procedure, for helpful suggestions and advice. References I. H. A. Sherman: The Evaluation of Coal for Use in Domestic Stokers. Univ. of Ill., Eng. Experiment Station, Circular No. 39 (1939). 2. . Q. Shotts: The Relation of Free- swelling Indexes to Other Characteristics of Some Alabama Domestic Stoker Coals. TP 2314, Coal Tech., (Feb. 1948); Trans. AIME (1948) 177, 502. 3. . J. Helfinstine and C. C. Boley: Correlation of Domestic Stoker Combustion with Laboratory Tests and Types of Fuels 11. Combustion Tests and Preparation Studies of Representative Illinois Coals. Ill. State Geol. Survey, Re1. of Zntlestigations No. 120 (19467 ) p. 35. DISCUSSION E. R. Kaiser*—AS a former fuel engineer assigned to residential stokers at Battelle, the writer has read with considerable interest the paper by Messrs. I'urdy and Nelson. It is gratifying to note that earlier test techniques have been developed and that criteria found important in the years 1935 to 1938 are still important in judging the performance of stoker coals for residential heating. The authors have plotted a number of the primary coal data singly against performance data of the stoker in an effort to establish relationships. Unfortunately, wide scattering of points usually resulted, which did not illustrate what experience generally indicates to be the case. For example, Fig 3 indicates almost no trend in the percentage of released ash converted to clinker with change in ash-softening temperature. Other factors, such as fuel bed temperatures and zones of heat release must have influenced the results. In the present state of our knowledge, we cannot explain all of the reasons why suitable stoker coals perform satisfactorily, nor why one satisfactory coal may be better than another. It would therefore

Jan 1, 1950

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

By L. W. Pommier, F. B. Brien

In order to determine the ability of cyclones with heavy liquids to preconcentrate ores, a study of the variables which govern the behavior of the solids in the apparatus has been made. To assess the test results, the cyclone products have been examined by sink and float analysis at various specific gravities and the results examined by the Tromp type curves. This analysis has allowed the development of the SG50 unit — specific gravity of the particles, 50% of which goes to overflow and 50% to underflow — rather than the d50 (size) unit used in classification. The results of tests using the closed circuit laboratory cyclone assembly with dry feed samples show the validity of the equation: Results indicate that 83% of the feed may be rejected containing 0.1% Sn. Recoveries in excess of 80% are obtained at a grade of 1.7% Sn from feed samples assaying 0.4% Sn. As water-wetted particles may comprise the plant feed, separate tests were performed to examine the effect of water in the feed material. Results indicate that the entrained water divides into two fractions, one of which is defined as free water and is rejected to the cyclone overflow, the other fraction forms an adhering envelope of water on the ore particles, altering their effective size and density. The presence of the envelope of water on the particles increases the ease with which the heavy liquid can be recovered but decreases the concentration efficiency. It is proposed that the detrimental effect of water in the cyclone may be minimized by using a higher feed pressure cx by the use of surfactants. A higher feed pressure, by increasing shearing forces, would reduce the thickness of the water envelope on the particles. The surfactants, by adsorbing on the particles and producing hydrophobic surfaces, would displace the water envelope and allow the heavy liquids to wet the modified surfaces. In both cases a larger proportion of the entrained water would report to the cyclone overflow as free water, thus minimizing the detrimental effect of water on the concentration efficiency. Additional testing is required on the behavior of water in the system; to determine the optimum particle size for the preconcentration step; to determine final particle size for optimum liberation and subsequent treatment of the products in present plants and to determine the efficiency with which the heavy liquids may be recovered from the products. For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Boliva today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since heavy liquids are now available with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined. THEORY AND TECHNICAL CONSIDERATIONS Three types of heavy liquids are available: aqueous solutions of very soluble salts, salts or mixtures of

Jan 1, 1964

By G. W. Binkley, G. K. Dumbauld, F. A. Brooks, B. E. Morgan

In recent years, oil well cementing compositions have been developed with low densities, controlled set strengths, and satisfactory thickening times. With the introduction of the permanent-type well completion method for cementing wells, another property—that of rate of filtration or water loss to permeable formations— has become important. Laboratory data show that cement slurries prepared with oil, water, bentonite, and calcium lignosulfonate possess satisfactory thickening times, strengths, and filtration properties for primary cementing of casing and for squeeze cementing with the permanent-type well completion technique. Cementing compositions have been prepared with oil-in-water emulsions varying in composition from 60 cc water and 20 cc oil per 100 gm cement to 90 cc water and 45 cc oil per 100 gm cement. These compositions have contained from 0.4 to 5.0 per cent calcium lignosulfonate by weight of dry cement. Slurries prepared from these compositions weigh 11.4 to 13.1 lb/ga1 and have filtration rates of from 10 cc to approximately 100 cc in 30-min API tests at room temperature. The unfiltered emulsion cements develop one-day tensile strengths of 60 to 220 psi; and the filtered mass sets to tensile strengths of 60 to 150 psi in 12 hours and develops strengths of 320 to 515 psi in seven days when cured at 125° F. Field experience gained from 13 field mixing jobs demonstrates the utility of the emulsion cement for permanent-type squeeze cementing operations. INTRODUCTION In recent years, research in oil well cementing composition has been directed toward the development of cements having low densities, controlled set strengths, satisfactory thickening times, and low rates of water loss by filtration. Two well cementing compositions that have been developed with these properties are the modified cements containing, respectively, 12 and 25 per cent bentonite clay and various concentrations of calcium lignosulfonate1,2 In a search for other ways to incorporate these characteristics in a cementing composition, consideration was given to the rheological properties of oil-emulsion drilling fluids. Many of the desirable properties observed in oil-emulsion drilling fluids are equally advantageous in a cementing composition. For example, low water loss by filtration and low density, which are inherent characteristics of these oil-in-water emulsions, are desirable for many oil well cementing operations. Furthermore, oil-emulsion slurries have lubricating properties similar to those of oil-emulsion muds, a factor which should provide ease of rotation of casing during primary cementing operations. The properties of lubrication and low filtration may be of special value in both primary and squeeze cementing operations encountered in slim-hole drilling. Studies in the preparation of oil emulsion systems have pointed out the need for violent agitation in order to disperse the oil into the water phase. It was thought, therefore,

Jan 1, 1957

By Milton Glicken

THE airborne geophysicist is a busy man these days. In his plane he may have the airborne magnetometer, the airborne scintillation counter, and the airborne electromagnetic surveying system. Each of these is an independent tool, but all require additional auxiliary equipment for locating the aircraft in space: recording altimeters and Shoran or aerial cameras. Now there is still another piece of equipment, the airborne magnetic gradiometer, an accessory to the magnetometer. To understand its uses, consider the function of the magnetometer itself. Aside from detecting magnetic ore, the airborne magnetometer finds greatest use in spotting intrusions of igneous material. Where there is enough contrast in magnetic susceptibility of igneous rock and adjacent formations, it outlines the intrusion. Certain minerals also influence the magnetometer directly, but with the exception of magnetite and possibly one or two others, their effect is weak and can be detected only when there is sufficient ore and the magnetometer flight passes very close to it. An igneous intrusion of infinite depth with vertical sides is represented on a magnetometer record by an anomaly, as in Fig. 1. Amplitude of the high depends on susceptibility contrast of the igneous rock. Generally speaking, the edge of the intrusion lies below the point of inflection of the curve, and this point, where the curvature changes from positive to negative on the magnetometer profile, would be near A in Fig. 1, with a counterpart, of course, on the other side. Location of the contact is one of the principal objects of the survey, but finding the precise point is not always easy, as inspection of the curve near A will show. Mineralization is often found at the contact zones, as at B. Magnetic effects, if detected, may be small, as in B', and when superimposed on the anomaly due to the instrusion they are very difficult to discern and analyze. Furthermore, if these small fluctuations are to be perceived by the magnetometer the vertical scale should be large. This increases the slopes of the anomaly and makes detection of small deviations and inflection points even more difficult. The airborne magnetic gradiometer was designed to help overcome these difficulties. What it presents is the first derivative of the magnetometer record with respect to time, that is to say, the slope at any point. Fig. 2 represents an actual magnetometer record (solid line) with the corresponding gradiometer record (dashed line) superimposed. Both records read from right to left. Vertical lines on the original magnetometer record are automatic steps designed to keep the pen from going off scale. The slope of any curve is greatest at the point of inflection or point where the curvature changes sign, and this point is a maximum (or minimum) on the gradi- ometer. The chief advantage of the gradiometer is that maxima or minima are much easier to see and to locate precisely; hence an accurate location for the point of inflection can easily be found. Note that points C and D are more sharply defined than C and D'. Similarly the small fluctuations of the original record, so important to the interpreter, are far more clearly shown at E, F, and G, than on the original record at E', F', and G'. Though not necessarily highs and lows on the gradiometer, they do show up clearly what would take a painstaking analysis to detect on the original magnetometer record. Will the gradiometer have a particular configuration which indicates an orebody? Not necessarily. The total intensity curve, or original magnetometer record, can display an orebody in various ways, depending on dimensions, orientation, latitude, and composition, as well as on direction, flight height, and instrumental sensitivity of the traverse. Where the total intensity can take on so many different shapes the gradiometer must vary too. It is generally recognized that interpretation of total intensity magnetometer records requires an expert analysis; the gradiometer can be of considerable assistance to the expert but it does not replace him. Mechanism of the gradiometer is simple. A Leeds & Northrup recorder in the aircraft records the magnetic gradient simultaneously with the total intensity, which is on another recorder. Fiducial marks are put on both records simultaneously and the speed of the paper through the recorders is kept the same on both. This makes it possible to place one record over the other for direct comparison. In the laboratory the flights are positioned on a map. Maximum and minimum points on the gradiometer, which can then be posted on the map at their proper locations, may be expected to fall along a trend crossing the direction of flight. Trends should indicate the edge of an intrusion, or some other important features, and when superimposed on the total intensity contour map help greatly to locate the points of inflection, or line of zero curvature.

Jan 1, 1956

By George Rice

SOME form of longwall mining is generally used in Continental Europe; also in Great Britain where the coal is weak and friable, or the coal bed provides material for pack walls and filling, or where the bottom is soft and squeezes up easily, or the roof is pliable, or the bed is thin and brushing provides building material, or the thick multiple seams are mined in layers, such as the 24-ft. seam at Weymss, Scotland or the 10-yd. pitching bed near Coventry, England. Pillar methods have been retained in British fields where the coal beds are from 5 to 9 ft. (1.5 to 2.7 m.) thick, and free from thick partings or binders or without draw slate, which would provide waste rock for pack walls, or where the roof is hard and requires shooting to bring down and also the bottom or floor is comparatively hard. The room-and-pillar system, by which probably 95 per cent., of the coal of the United States is produced, is now found in only a few mines in Wales, where it is known as the pillar. and .(single) stall method. The American room-and-pillar system is not equivalent to the bord-and-pillar or stoop-and-room system. The essential difference between the bord-and-pillar and the average American room-and-pillar system is probably due to natural conditions. The majority of the coal mines in the United States have a depth of less than 700 ft. (213.m.). The bulk of the coal mined in Europe comes from a depth of more than 1200, ft., while the deepest mines in Great Britain, Belgium, and France reach 3500 to 4000 ft. In deep workings wide spans are impracticable, even with the use of abundant timber; accordingly, as the mines in the United States become deeper the rooms will become narrower and the pillars thicker, and the bulk of the coal will be extracted on the retreat. It is generally conceded, without reference to the cost of production, that the larger the pillars left on the first mining, the more thoroughly can the, coal be extracted. In Europe complete extraction is generally compelled either by the lessors or by the governments; whereas in this

Jan 2, 1921

By G. C. Weaver, G. T. Harley

BEDS or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the refinery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3000 ft. Cable or rotary tools are used to drill down to the salt. When samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16-in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in, line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to occur from nitrogen gas trapped under the several polyhalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically 100per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon, and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of ore beds between drill holes is briefly described.

Jan 1, 1946

By G. S. Rice

Some form of longwall mining is generally used in Continental Europe; also in Great Britain where the coal is weak and friable, or the coal bed provides material for pack walls and filling, or where the bottom is soft and squeezes up easily, or the roof is pliable, or the bed is thin and brushing provides building material, or the thick multiple seams are mined in layers, such as the 24-ft.seam at Weymss, Scotland, or the 10-yd. pitching bed near Coventry, England. Pillar methods have been retained in British fields where the coal beds are from 5 to 9 ft. (1.5 to 2.7 m.) thick, and free from thick partings or binders or without draw slate, which would provide waste rock for pack walls, or where the roof is hard and requires shooting to bring down, and also the bottom or floor is comparatively hard. The room-and-pillar system, by which probably 95 per cent. of the coal of the United States is produced, is now found in only a few mines in Wales, where it is known as the pillar and (single) stall method. The American room-and-pillar system is not equivalent to the bord-and-pillar or stoop-and-room system. The essential difference between the bord-and-pillar and the average American room-and-pillar system is probably due to natural conditions. The majority of the coal mines in the United States have a depth of less than 700 ft. (213 m.). The bulk of the coal mined in Europe comes from a depth of more than 1200 ft., while the deepest mines in Great Britain, Belgium, and France reach 3500 to 4000 ft. In deep workings wide spans are impracticable, even with the use of abundant timber; accordingly, as the mines in the United States become deeper the rooms will become narrower and the pillars thicker, and the bulk of the coal will be extracted on the retreat. It is generally conceded, without reference to the cost of production, that the larger the pillars left on the first mining, the more thoroughly can the coal be extracted. In Europe complete extraction is generally compelled either by the lessors or by the governments; whereas in this country it has been more largely a question of competitive cost of production, or the support of the surface in the flat farming districts of the

Jan 1, 1922

By P. G. Winchell, R. J. Russell

The distribution of displacements of originally plane surfaces by an invariant-plane strain has been analyzed statistically. The displacement ratio (the magnitude of the displacement of a point originally a unit distance from the invariant plane) can be determined from an analysis either of tilts of random surfaces or of displacements of random scratches scribed on a randowz surface. In either case the mean of the tangent of the observed displacement angle is related to the displacement ratio, and the number of observations used in determining the mean is related to the confidence limits placed on the estimate of the displacement ratio. In estimating the effect of applied stress on a phase transformation whose displacement effects can be approximated as an invariant-plane strain,* the dis- placement ratio of the invariant-plane strain is of primary importance. Two procedures for determining such displacement ratios are considered here. In the tilt method the measured quantity is taken to be the angle through which a random polish plane is rotated by the invariant-plane strain. In the scratch method the measured quantity is taken to be the angle between the original direction of a random scratch in a random polish plane and the projection of its final direction in the polish plane. In order to obtain precise results from either of the methods, it is necessary to measure the relative volume change associated with the strain in a separate experiment. TILT METHOD A locally homogeneous invariant-plane strain, P, with displacement ratio, S, may be written&apos; where ; and < are unit vectors indicating the displacement direction and invariant-plane normal, respectively, as pictured in Fig. 1. Eq. [I] describes a uniaxial strain if the direction of displacement is parallel to the invariant-plane normal and a pure shear strain if the displacement direction is perpendicular to the invariant-plane normal. The original orientation of the random polish plane relative to the invariant plane and to the displacement direction is shown in Fig. 2. The angle 03 between < and u is related to the relative volume change, ?V/V, and to the displacement ratio by As a result of the invariant-plane strain, the polish plane is rotated about its intersection with the invariant plane by the angle y, which is always taken to be positive. The tangent of this angle in terms of the above parameters is

Jan 1, 1967

By Lucien Eaton

The use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material must be used. In different parts of the world sand, clay, gravel, culm, granulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, but to describe some of the methods used for placing sand fill and to make a brief comparison of their merits. Methods of Placing Sand Sand may be transported and placed underground by several methods, which may be classified as follows: 1. By Hand.—The sand, which must be comparatively dry, is taken down the shaft in cars on cages and is distributed to its destination in these cars, or it is dumped down raises and is drawn off and distributed by means of cars, wheelbarrows or scrapers.

Jan 1, 1932

By T. S. Washburn

Deoxidation is one of the most complex metallurgical operations in the basic open-hearth process. The necessity for deoxidation arises from the fact that the refining operations that precede it require the oxidation of the steel bath. when the refining is completed and the desired composition of the bath has been obtained with respect to the elements subject to control by &apos;oxidation. there is usually an excess of oxygen present in the bath from the standpoint of the amount desired in the finished steel. The objectives of deoxidation are to control the amount and type of oxides and, although not directly ilnp1it.d by the term or always considered as a Part of the process, to control the amounts of gases such as hydrogen or nitrogen that will be present in the finished steel. There are other aspects to be consideretl in connection with deoxidizing procedures. In addition to the primary objectives of oxide and gas control. the composition of the steel is affected by the elements introduced during the deoxidizing process. Factors in furnace operations are likewise involved, such as slag composition, temperature control. arid heat time. .ill of these should be considered in establishing the most satisfactory deoxidizing procedure for each grade of steel. The purpose of this paper is to outline the objectives of deoxidation as related to steel characteristics, and to summarize the factors in furnace practice and the economic aspects to be considered in connection with deoxidation procedures. Objectives of Deoxidation The primary objectives of deoxidation are the formation and elimination of oxides. The amount of oxygen present in the bath prior to deoxidation is an important factor, since it is the basis of any deoxidation procedure. The oxygen content of the bath is primarily a function of the carbon content, although it is affected also by the temperature, the oxidation of the slag, and transient conditions within the furnace. The relation of oxygen to carbon in the bath is shown in Table I. Table I shows that under actual operating conditions, the amount of oxygen present in the bath is higher than the theoretical amount. This relation would be expected, since the bath is in a state of metastablc equilibrium during the period that the carbon is being eliminated. The most important feature demonstrated by this table, however, is the rapid increase

Jan 1, 1945

By George W. Small

The ore, as it is raised from the mine, has all average assay-value of $11 per ton, chiefly in the form of free gold. All the ore goes directly to the stamp-mills, of which there are two. The older and larger mill contains sixteen batteries of five stamps each, with one Frue vanner to each battery. The new mill has eight batteries of five stamps and two Frues to each battery. The large mill is driven by Leffel turbine wheels, with a pressure of eighty feet, and a consumption of 600 miners&apos; inches of water. The smaller mill is driven by "hurdy-gurdy" wheels with a pressure of about 550 feet and a consumption of 150 inches of water. At both mills the tailings from the stamps pass over about 20 feet of plates on their way to the Frues. In each set of plates the first or upper one is copper, the rest are so-called silver plates. The bullion from the stamps is about 800 fine in gold and 200 in silver. The concentrates from the Frues average from 11/4 to 1 ; per cent. of the ore stamped. They very rarely exceed 2 per cent. I was unable to get the exact assay-value of the concentrates, but it is said to vary between $100 and $200 per ton. The concentrates are treated at the chlorination works at the rate of one hundred tons per month. The capacity of the works is somewhat greater than this, but as the supply of concentrates is limited it is not deemed advisable to work them up any faster. Care is taken to keep the concentrates always damp until they are put into the roasting furnace. If this is not done, a decomposition of the pyrites begins, forming lumps which do not roast, and which consequently cause a loss of gold in the residues from leaching. A Fortschaufelungsofen is used for roasting. Its dimensions, incloding fire-box, are 12&apos; X 80&apos;. The hearth is one continuous plane, but the charges, of which there are three in the furnace at one time, are kept entirely separate. The furnace-men call the three compartments, the "drying," the " burning," and the " cooking" compartments. In the middle, or "burning" compartment, the ore is spread

Jan 1, 1887

By Charles Legrand

(San Francisco Meeting, September, 1915) THE problem of mine pumping is so much affected by local conditions, and those conditions are so liable to changes during the life of a mine, that the best system to use is difficult to determine. The experience of the;, writer has been that, in general, for copper mines, electric pumping is most satisfactory unless the quantity of water to be pumped is great or. the mine does not use electric power for any other purpose. As a rule, however, figuring on the cost of necessary power plant, the total cost of: installation is greater with electric pumps than steam- pumps. As the water is liable to be gritty, outside-packed plunger pumps are to be recommended, and if the water is not acid, or only slightly so, chilled cast-iron plungers pay for their extra cost very quickly in diminished cost of packing. With chilled plungers it is possible to use metallic, packing instead of soft packing, if the water, is not too gritty nor the lift too high. In vertical pumps this packing is satisfactory for lifts up to 400 ft., in the experience of the writer; and may be found satisfactory for higher lifts. For water slightly acid, cement-lined pump bodies have given good satisfaction. For acid. water, both plungers and pump bodies should be made of acid-resisting bronze. For high lifts, especially with gritty water, a satisfactory pump valve is difficult to find. To reduce the unbalanced pressure on the valve at time of opening it is advisable to have narrow seats; this, however, brings high pressure on the seats when the valve is closed. On large valves for lifts of 600 to 1,000 ft. we have used leather, hard rubber, vulcanized fiber, and soft brass; for clear water the latter has given best satisfaction. The difficulties due to grit make it advisable to have large sumps where water can settle, and if possible, to have two of them so that they can be cleaned alternately. At the mines of the Old. Dominion Copper Mining ,& Smelting Co.; Globe, it was found that a small air. ejector discharging into a mine car is a very convenient way to clean mud and sand from a sump. .

Jan 9, 1915