Search Documents

By N. W. Ratliff, P. J. Closmann

Production of oil by expansion from a cylindrical reservoir composed of two concentric regions of different properties has been determined as a function of time for a reservoir producing at constant terminal pressure. The parameters involved are permeability, porosity, compressibility and oil viscosity. Results agree with those of a generally accepted method for uniform reservoirs when all parameters are taken as uniform. Cumulative production at any given time is reduced below that of the uniform reservoir when a region of considerably lower permeability adjoins the well; cumulative production increases when a high-permeability region adjoins the well. Curves are presented illustrating quantitative effects of these variations. INTRODUCTION Most petroleum reservoirs can be exploited by release of pressure and consequent expansion of underground fluid. During part of the production history of certain reservoirs by this mechanism, fluid compressibility can be considered small and constant. Cumulative fluid produced by this means as a function of time was calculated for a uniform reservoir by van Everdingen and Hurst.l For certain cases where a production well has been damaged or where an acid treatment has been used, a zone of properties different from those of the reservoir may be created around the production well. In such a case, expansion of the reservoir fluid takes place in a system composed of two concentric cylindrica1 regions of different reservoir properties. Such composite systems were studied in connection with heat flow by Jaeger2 who presented a solution for temperature distribution in a radial system with an infinitely large outer radius. Similar heat flow problems have been studied by other authors Oil production from composite reservoirs was studied for constant production rate by Hurst,4 Loucks and Guerrero,5 and Carter.6 THEORY This work considers constant terminal pressure. Cumulative flow is calculated for a composite bounded system in which no flow takes place across the outer boundary (Fig. 1). Since the flow is considered to be purely radial, the problem involves only one space dimension and time. It is convenient to define the following dimen-sionless pressure drops (Fig. 1).

By P. R. Martin, R. B. Kelly

Drilling in Central Texas during 1933 was confined, for the most part, to the search for new serpentine plugs. Bastrop County led in this particular activity, with 50 completions during the 12 months' period, 12 of which were productive. Only one new field was opened in Central Texas during the year, it being known as "Hilbig" (Bastrop County) and was discovered by the Humble Oil & Refining Co. The finding of commercial production in the serpentine at 2500 ft. led to further search in this and surrounding counties, but without success. Bexar County actually provided the greatest amount of drilling but the activity was limited to shallow development from 400 to 2000 ft. The Edwards limestone pay, which has been such a factor in past years, received but slight attention during 1933. Unsuccessful exploration was carried on in Lee and Burleson counties. With the exception of Freestone County, the Woodbine sand area was given even less consideration. This county, because of its close proximity to Anderson and Leon counties, saw a very active leasing campaign and several important tests drilled. In Central Texas, 252 wells were completed in 1933, and of this number 52, or 21 per cent, were productive. Hilbig Field The discovery well, Humble Oil & Refining Company's Annie Hassler No. 1, was completed Feb. 16, 1933, for an initial production of 65 bbl. the first hour, through tubing and 1/2-in. choke. The production was found in serpentine at 2468 ft. and tested 37.2" A.P.I. gravity. Twelve producing wells were drilled during the year and served to indicate that not more than 300 acres would comprise the entire field. Daily production at the end of the year was 775 bbl., although the field potential was 18,240 bbl. daily through 1-in. choke. The field adapts itself to pressure maintenance, and this scientific handling is being undertaken by the Humble Oil & Refining Co. through one injection well. It is the only area in the district where work of this nature is under way. Proration of Oil The more stringent application of proration in 1933 did not affect materially the producing fields in Central Texas. This is accounted for

Jan 1, 1934

By E. T. Peters, L. E. Tanner

In the course of a study concerned with the rnechanical behavior of the intermetallic compound CO3V, both structural observations and anomalous electrical-resistivity behavior indicated the presence of a new high-temperature phase in an alloy with the stoichiometric composition, Co-22.4 wt pet V. The evidence, which is given below, suggests that the new phase is situated between the low-temperature ordered hexagonal phase, k,1, 2and the high-temperature disordered fee solid solution, a,3 within a small range of temperature in the vicinity of 1070°C. Structural studies included X-ray diffraction analysis* and electron-transmission microscopy examination* of stoichiometric composition speci- mens homogenized for 1 hr at 1200oC and either air-cooled or water-quenched. The air-cooled specimens yielded X-ray diffraction evidence of the k phase, while electron microscopy revealed a microstructure of both heavily and moderately faulted regions as shown in Fig. 1. The high density of stacking faults (or fine twins) in region A is reminiscent of hexagonal cobalt following its allotropic transformation.4 Selected-area diffraction from this region revealed distinct superlattice reflections of the ordered hexagonal phase, as well as continuous rel-streaks which were normal to the fault planes in the micrograph. The latter is indicative of extremely small spacings between the faults.' Regions such as ß were found to be only partially transformed to the k phase. Attempts to study the antiphase domain structure by either bright- or dark-field techniques were unsuccessful in these initial studies. This was due to the low intensity of the superlattice reflections arising from the closeness of the cobalt and vanadium scattering factors. Quenching Co3V from above Tc appears to suppress the formation of the k phase. Both X-ray and electron-diffraction results indicated that the disordered phase, a, was partially ordered during severe cooling and that the structure of the ordered phase was of the L12 (Cu3Au) type,6 designated here as a'. As in the case of the hexagonal phase, examination of the domain structure was unsuccessful; however, significant information concerning the morphology of this condition was revealed by the appearance of dislocation arrays. In particular, it

Jan 1, 1965

By H. J. Morel-Seytoux

The influence of patten, geometry on assisted oil recovery for a particular dispIacement mechanism is the object of investigation in this paper. The displacement is assumed to be of unit mobility ratio and piston-like. Fluids are assumed incompressible and gravity and capillary effects are neglected. With these assumptions it is possible to calculate by analytical methods the quantities of interest to the reservoir engineer for a great variety of patterns. Specifically, this paper presents (1) very brieily, the methods and mathematical derivations required to obtain the results of engineering concern, and (2) typical results in the dorm of graphs or formulae that can be used readily without prior study of the methods. Results of this work provide checks for solutions obtained from programmed numerical techniques. They also reveal the effect of pattern geometry and, even though the assumptions of piston- like displacement and of unit mobility ratio are restrictive, they can nevertheless be used for rather crude but quick, cheap estimates. ,These estimates can be refined to account for non-unit mobility ratio and two-phase flow by correlating analytical results in the case M = 1 and the numerical results for non-piston, non-unit mobility ratio displacements. In an earlier paper1 it was also shown that from the knowledge of closed form solutions for unit mobility ratio, quantities called "scale factors" could be readily calculated, increasing considerably the flexibility of the numerical techniques. Many new closed farm solutions are given in this paper. INTRODUCTION BACKGROUND Pattern geometry is a major factor in making water-fIood recovery predictions. For this reason many numerical schemes have been devised to predict oil recovery in either regular patterns or arbitrary configurations. The numerical solutions, based on the method of finite difference approximation, are subject to errors often difficult to evaluate. An estimate of the error is possible by comparison with exact solutions. To provide a variety of checks on numerical solutions, a thorough study of the unit mobility ratio displacement process was undertaken. To calculate quantities of interest to the reservoir engineer (oil recovery, sweep efficiency, etc.), it is necessary to first know the pressure distribution in the pattern. Then analytical procedures are used to calculate, in order of increasing difficulty: injectivity, breakthrough areal sweep efficiency, normalized oil recovery and water-oil ratio as a function of normalized PV injected.

Jan 1, 1967

By Marion Rice

The copper-mining district of Jerome, Ariz., is of such economic importance that the following brief notes may be of interest. The ore deposits are said by Ransome1 to be pre-Cambrian, and are contained in the pre-Cambrian schists of the region. In the vicinity of the mine (the United Verde) the schist stands nearly vertical and strikes a little west of north. At least three varieties are distinguishable—(1) a green rock, schistose on its margins but grading into massive material, which is evidently an altered dioritic intrusive; (2) a rough gray schist with abundant pheno-crysts of quartz, apparently an altered rhyolite; and (3) a satiny, greenish gray, very fissile sericitic schist that may be a metamorphosed sediment. The ore occurs in varieties (2) and (3), the main belt of dioritic rock (1) lying just west of the orebodies. The ore is said to follow as a rule the layers of fine sericitic schist. T. A. Rickard2 Says that the ore at the United Verde Extension mine is found at the contact of diorite and schist, that both diorite and ore are earlier than the regional metamorphism, and that the quartz porphyry ("rhyolite" of Ransome) is of post-Cambrian age. The material considered here, a part of which was gathered by the writer, came from four of the mines of the district, and its study was undertaken at the suggestion of Dr. Berkey of Columbia University. The field relations and exact locations of the different specimens are not known, but a microscopic study of the thin sections gave some evidence as to the origin of the ore, which will be discussed below. The indications are that both ore and porphyry were introduced at the closing stages of the metamorphism, this being in accord with Ransome's view of the genetic relation of porphyry and ore rather than with the opinion that the ore is related to the diorite. Certain field occurrences mentioned in the literature also support this theory. Rickard, in the same article to which reference has been made, speaks of a vein of chalcocite several inches wide at the contact of one of the porphyry dikes, and Provot,3 although he regards the porphyry as subsequent to the ore, says: "Acid dikes encountered underground should be followed as they have been found in practice to lead to orebodies."

Jan 1, 1920

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By Arthur Gibson

Synopsis.-A new feature in coal mining, where the coal is to be conveyed from a high to a lower elevation and the topography of the country is such as to preclude surface haulage. The distance from the mine to the tipple inn this instance is about 3,000 ft. and the difference in elevation between the terminals 321 ft., of which 225 ft. occurs in the first 1,300 ft. from the loading terminal. A mine car was designed especially for this plant consisting of two tramway buckets on one pair of trucks, the buckets being lifted from the truck, attached to the train line automatically, and conveyed to the tipple. THROUGHOUT eastern Utah, in the Book Cliff range and the Wasatch plateau, the coal-bearing measures are admirably exposed, in the bold and for the most part bare escarpments. The geology is simple, the rocks being almost flat, or at the most dipping not more than 10 per cent. The coal beds occur in a formation, or group of strata, consisting of sandstone and shale, 600 to 800 ft. thick, which has been correlated with the Mesaverde formation of the Cretaceous. Above this occurs about 2,000 ft. of alternate layers of buff-colored sandstone and shale. Below the coal lie the Colorado shales, which are estimated to be about 1,500 ft. thick, below which are the red rocks of the Jura-Trias. As a rule the coal beds all clip in a northerly direction and under the high mountain. The canyons opening out into what is known as Castle valley all cut the coal beds, and the beds rising in the direction of the valley are found frequently high up on the escarpment, often as much as 1,000 ft. above the valley. The surface features of the region have an economic bearing on the availability of the coal. The valleys and gulches in the Colorado shale extend out from the coal areas across the edge of the plain, so that it is impracticable to build transportation lines parallel with the boundaries of the field within several miles of the coal land. It will be necessary, therefore, to build branch lines up to the coal lands from points on the Denver & Rio Grande Railroad traversing Castle valley.

Jan 10, 1914

By L. F. Rooney

In June 1964 the Indiana Geological Survey discovered gypsum beds more than 10 ft thick in rocks of Devonian age in La Porte County, Ind. Although the extension of the Michigan Basin evaporites into northern Indiana has been recognized for some time, the gypsum beds have been regarded as either too thin or too deep for exploitation. Current Survey research, however, indicates that exploration by industry might find commercial deposits of gypsum less than 50 miles from Chicago. In four cores taken by the Survey within 1 sq mile in La Porte County, the maximum thickness of inter-bedded gypsum and anhydrite is 35.8 ft. Both gypsum and anhydrite beds contain irregular masses of limestone and dolomite that average a few inches in cross section and total about 20% of the rock by weight. The maximum thickness of gypsum in one minable unit verified by core is 12.5 ft, and its purity is 81.3%. Chloride content of the gypsum beds is less than 0.005%. Depth to the gypsum in La Porte County is 330 to 500 ft, about the same depth as the gypsum being mined in Martin County, Ind. In June 1964 the Indiana Geological Survey discovered gypsum deposits of probable commercial thickness near La Porte, Ind. (Fig. 1). This article presents preliminary data on the distribution, thickness, depth and chemical composition of the gypsum, the possible causes of gypsification, and economic considerations of immediate interest to industry. Because of the preliminary nature of the work, only a few geologic relationships concerning the genesis of the deposits will be mentioned. DEFINITIONS The following terms used throughout this article have been restricted to the following definitions: evaporites: anyydrite (CaSO4) or gypsum (CaSO4 . 2H2O). minable evaporites: any evaporite unit which may contain more than 80% evaporites, which is more than 10 ft thick, and which in places may be completely gypsified. PREVIOUS WORK The presence of gypsum and anhydrite in the Devonian rocks of northern Indiana has been recognized for at least 70 years1-4 and can be inferred from a number of reports on the geology of Michigan. For example, in a cross section from southwestern to central Michigan, Ells5 indicated the presence of

Jan 1, 1965

By C. M. Wayman, R. Bullough

The rediffraction of Bragg diffracted beams by differently oriented regions (such as twins) of a crystal may give rise to "extra" reflections or reciprocal lattice points. These two papers are concerned with predicting these additional reflections which result from twin related regions of a lattice. Analysis is made for {111}fcc twins, (112)bcc twins, and {hkil}hcp twins. It is first required, knowing the specific variant of the twinning plane in each case, to predict the positions of the twin reflections relative to the matrix reciprocal lattice. Once this is done, the positions of the "extra" multiply diffracted reflections may be deduced. Part I is devoted to establishing "selection ru1es" for twinning, i.e., the necessary and sufficient conditions for the existence of twinned reciprocal lattice points. 1. INTRODUCTION. Transmission electron diffraction patterns are frequently complicated by multiply diffracted beams. Pashley and stowell1 have recently demonstrated that certain extra reflections in evapo- rated films of gold result from the rediffraction of matrix Bragg diffracted beams by (111) microtwins in the gold. It was previously (and erroneously) suggested 2,3 that observed "irrational" reflections in fine-grained gold were due to the presence of some hcp gold. A similar situation exists, apparently, for some bcc materials; fine (112) twins in bcc martensite in Fe-Ni alloys4 give rise to extra reflections. There are many other examples. The number of transmission electron microscopic investigations is continually increasing, and because of the importance of double (and multiple) diffraction in the interpretation of diffraction patterns, it was judged that a detailed elaboration of the principles involved is desirable, as well as the extension of these principles in reasonably closed form to other crystal structures, particularly bcc and hcp. The present analysis considers double diffraction caused by (111) twins in fcc metals, (112) twins in bcc metals, and {hkil} = {hkl) twins in hcp metals. For each case of twinning, the various possible (variants of) twins give rise to a set of interpenetrating reciprocal lattices. The relative spatial arrangements of these reciprocal lattices can be deduced (Part I) and are expressed in terms of simple "selection rules". The resulting sets of interpenetrating reciprocal lattices are then analyzed for possible doubly diffracted reflections (Part II). The notation used, and some important formulas are given in Appendices I and 11.

Jan 1, 1967

By G. C. Broadhead

THE lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top 1. Sandstone (the second of Missouri geologists), - 20 feet. 2. Cbert beds-beds of passage below, - 125 feet 3. Magnesian limestone, chert, and quartzite, - 100 to 300 feet 4. Lower magnesian limestone, - 100 to 150 feet 5. Gritstone and lingula beds, - 50 feet 6. Ozark marble beds, - 5 to 20 feet 7. Sandstone and conglomerate, - 5 to 90 feet 8. Porphyry, Archaean. 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as de¬tached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have pene¬trated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous sandrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called u mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

Jan 1, 1877

By R. J. Murphy, N. J. Grant, J. W. Dowding

A large number of blast furnace slag-metal tests were examined to determine if the manganese reduction could be used as a primary indicator of the degree of oxidation or reduction of the slag and of its desulphurizing power. Slag basicity and temperature were also evaluated. Two laboratory heats were made and sampled prior to reaching equilibrium to check blast furnace data. IN a recent investigation of the factors affecting desulphurization in the blast furnace, is was evident that manganese reduction appeared to parallel the course of desulphurization. Grant, Kalling, and Chipman1 pointed this out in a series of time studies utilizing closely controlled laboratory melts. Fig. 1 is a composite plot of sulphur removal and manganese reduction as a function of time under two slags of different basicity. Manganese reduction appears to approach equilibrium at approximately the same rate as does sulphur. It was also demonstrated that the addition of oxygen to the slag, as manganese oxide, caused a sharp reversal of sulphur from the slag to the metal.' It has been shown that "Excess CaO" was a primary factor in measuring the degree of desulphurization under ideal reducing conditions,1,2 the following reaction being representative of the process: CaO (slag) + S + C (solid) = CaS(slag) + CO (gas) It was also evident that a second reaction could drive the sulphur from the slag into the metal. A suggested reaction was' CaS (slag) + 0 = CaO (slag) + S Any change in the oxidizing power of the system would thus affect both the sulphur and the manganese without causing any change in the calculated basicity of the slag. "Excess CaO," "Excess Base," and other similar basicity values, under such oxidizing conditions, would therefore not be the best measure of desulphurizing power; instead, as was shown by and Chipman" he oxygen content of the slag at low oxygen levels would be the controlling factor. Unfortunately, the extent to which FeO is reduced in the blast furnace makes it difficult to utilize slag FeO as an accurate indicator of the degree of oxidation. By comparison, manganese reduction in the blast furnace proceeds more slowly and is generally only about 40 to 70 pct complete. manganese, which is present in significant amounts and is readily analyzed, offers an opportun-

Jan 1, 1954

By G. C. Broadhead

The lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top: 1. Sandstone (the second of Missouri geologists),.... 20 feet. 2. Chert beds—beds of passage below,...... 126 " 3. Magnesian limestone, chert, and quartzite,. .. 100 to 300 " 4. Lower magnesian limestone,......100 to 150 " 5. Gritstone and lingula beds,....... 50 " 6. Ozark marble beds,........5 to 20 " 7. Sandstone and conglomerate,. .. .. 5 to 90 " 8. Porphyry, Archæan 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as detached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have penetrated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous saudrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called " mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

By William Hague, Robert H. Bedford

The objects of this paper are: 1. To give cost data on drilling obtained at the North Star mine in California; 2. To describe the methods of testing drills employed there, giving the results of shop tests, and the correlated data obtained underground; 3. To demonstrate that these tests form a satisfactory basis upon which to judge rock drills. The rock at this mine is either close-grained diabase in the upper levels, or tough grano-diorite in the lower levels. The vein, which has an average dip of 23", consists of about 5 ft. of " formation" lying between walls of unaltered country rock. Of the 5 ft., solid quartz and stringers make up 18 in. of pay ore. The formation, which consists of but slightly altered country rock, is almost as hard as the unaltered walls. From 4 to 44 ft. is sent to the mill. One-third of the holes are drilled in the quartz; two-thirds in the formation. The holes are about 4 1/2 ft. deep and break on the average of 1.15 tons per hole. The average number of holes per stope drill shift is at present 5.65. The number of drill shifts throughout the mine in 1913 was 18,679, and the cost of labor for drilling, power, supplies, upkeep of machines and air lines, tool sharpening, and distribution, amounted to 33 per cent. of total mining expense. To do this work there are in commission 43 No. 12A, three No. 17V and eight No. 16V Waugh stopers, three Jackhamers, two Waugh pluggers, and 17 No. 8 and two NO. 7 water Leyners. For the past three years a record has been kept of the repairs on each machine and number of shifts operated by it. The figures given in Tables I and II for the cost of repairs per drill shift have been taken from this record. The underground air pressure is about 90 lb. The air consumption per drill shift was measured by aerometers. The leakage of pipe lines between compressor and meter is not included. From the number of pieces of steel sharpened for each type of drill during the year the average used per drill shift has been ascertained. For other supplies the figures given represent a year's average.

Jan 1, 1915

By D. R. Snow

The year 1930 stands out in the petroleum industry as an exceptional one in many ways. It is one of the few years in its history during which crude oil production declined from that of the previous year in nearly every important producing district in the United States and in the world as a whole. World production of crude oil declined approximately 81,000,000 bbl., from 1,484,451,000 bbl. in 1929 to 1,403,500,000 bbl. in 1930. Production of crude oil in the United States declined approximately 111,000,000 bbl., from 1,007,323,000 bbl. in 1929 to a production of 896,265,000 bbl. in 1930. World production outside of the United States increased approximately 30,000,000 bbl., due principally to the increased production in Russia. This, together with the decided decrease of production in the United States, resulted in a smaller percentage of world production in the United States than in any other year since 1921. This declining production occurred in the face of the greatest visible supply in the form of potential production that the industry has ever known and was clearly the result of the great efforts put forward to restrict production, both by proration and by unitization. Throughout the year, developments along the lines of proration and unitization have overshadowed all other developments in the minds of those interested in the oil industry and will, no doubt, continue to do so more and more in the future, as it is quite evident that the industry cannot hope to maintain itself in a profitable position, without some rational plan of bringing about a better balance between supply and demand than has existed in the past. The successful operation of the Van field unitization agreement and the recently completed Kettleman Hills plan are indicative of what mag be expected in the future along this line. That real progress has been made in this direction is shown by the fact that total crude oil stocks in the United States were decreased by approximately 28,000,000 bbl. during the year 1930. This is the only year on record during which such a decrease of crude oil stocks was accompanied by a severely declining price structure. This reduction of crude stocks is apparently continuing even after the price has reached its present low level, indicating that there is no

Jan 1, 1931

By J. T. Norton, A. L. Mowry

S. J. SINDEBAND*—(1) Discussing the properties of the powders used, Mr. Rostoker mentioned a silicon powder as being between 150 and 325 mesh. We always had much difficulty in measuring particle size of silicon powder by screen analysis, because of its tendency to agglomerate. I would be interested in the method used to measure these particle sizes. (2) Mr. Rostoker maintains that the measurement of magnetic properties is more accurate in determining complete homogenization of an alloy, than is the X ray diffraction technique. I wonder whether this is really true. Even when diffusion is complete, magnetic properties will change during continuation of the heat treatment, due to change in density and pore shapes, as has been demonstrated by Mr. Rostoker himself. Which effect is faster, the diffusion of the alloy components or the attainment of final density, will, in my opinion, depend very much on initial material and sintering conditions used. For magnetic applications, of course, the magnetic measurements are most suited for determining the point at which equilibrium conditions are reached. (3) I was glad to see that Mr. Rostoker had used sample sizes which are similar to those I had used previously, and I believe that ring samples of about 2 in. od will become more or less standard samples for the determination of magnetic properties of powder metallurgy products. I should like to ask how the density was changed for the samples on which the effect of porosity was investi- gated, and, further, why the sintering temperature used for this series of experiments was so low. It is somewhat surprising that a 24-hr treatment at 850°C acts so much more to spheroidize the pores than a treatment for 1 hr at 1100°C. But the effect seems to be indisputable. I have made an investigation of the influence of sintering temperature for longer times on the maximum permeabilities of iron powder compacts which was presented at the International Powder Metallurgy Conference in Graz, in 1948, and I hope that these results will be published here within a short time. The results of this investigation are confirmed by Mr. Rostoker's findings that the change of time from 1 to 24 hr changes the permeability behavior considerably in the direction as indicated by Polder and Van Santen for spheroidiza-tion of pores. I do not quite understand Mr. Rostoker's explanation of the influ-

Jan 1, 1950

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By W. H. Hough, P. B. Leavenworth

Development in the upper Texas Gulf Coast during 1944 resulted in the discovery of 19 new fields as compared with 11 during 1943. These discoveries include 10 oil fields, one dry gas field, and eight gas-condensate fields. Drilling During the year 590 wells were drilled as compared with 418 drilled during 1943. Of these operations, 485 wells were drilled in proven fields, with the following results: 281 oil wells, 22 condensate wells, one dry gas well and 141 dry holes. The remaining 105 wells were wildcats, of which 19 were producers. The geological distribution of these discoveries was as follows: In 1944, production amounted to 178,-522,630 bbl., which was an increase of some 31,670,384 bbl. over the 1943 figure of 136,852,246 bbl. These figures include both condensate and oil production, as separate figures are not available. Wildcatting in the area was more successful during 1944 than in 1943 as the following comparison of number of wells drilled illustrates: Discoveries during 1944 Smith Point, Chambers County.—Standard Oil Company of Texas completed its No. I State, sec. 109, on Feb. 15, 1944, in a Frio sand at 8135 to 8146 ft. The well flowed 250 bbl. of 42º gravity oil through an 1/8-in, choke. Gas-oil ratio was 800 to I; tubing pressure, 1100 bbl. Four other oil wells and one gas well were completed during the year. This discovery does not appear to be of major importance. The producing area lies on the upthrown side of a large fault. North Winnie, Chambers County.—Sun Oil Co. completed No. I P. E. Dougherty on Apr. 27, 1944, from the Frio, through perforations at 8757 to 8759 ft. The initial production was 154 bbl. of 38.3º gravity oil through an 1/8-in. choke. Gas-oil ratio Was 2526 to 1; tubillg Pressure, 2280 1b.; casing Pressure, 1225 lb.; total depth, 9519 ft. Three other wells were drilled during the Year. This discovery is on the downthrown side of the major Winnie Stowell fault, and increases in magnitude the already large producing area along this fault. Mayes Field, Chambers County.—Humble Oil and Refining Company's No. I Mary Etta Mayes was completed on Dec. 24, 1944, in a Frio sand, at 8166 to 8169 ft. through 1/4-in. for 768 bbl. of 40.3º gravity

Jan 1, 1945

By P. Duwez, L. Zwell

In recent years, the problem of pressing metal powder in a die has received much attention. The question has been the object of a Symposium held in New York in March 1947 under the sponsorship of the AIME; an excellent review of the subject may be found in Ref. 1. Various experimental techniques have been used to study the behavior of the powder in a die cavity. Two methods have been particularly successful; one consists of measuring the density distribution²,³ and the other makes use of a lead grid in the powder during pressing.4 In the present study, the pressure at various points on the bottom and the sides of a die 1.50 in. in diam was measured by means of small piston dynamometers and resistance sensitive strain gauges. In order to correlate the results with previous investigations, the pressure distribution inside the compact has also been determined by an indirect method based on density measurements. Strain Gauge Measurements of Pressure on Side and Bottom of Die A schematic drawing of the die used for measuring side pressures is shown in Fig 1. The pressure gauge consists of a 0.25-in. diam piston A which transmits the pressure to a dynamometer B, on which two Baldwin Southwark type 4-14 strain gauges are fastened 180" apart. Because the installation of several dynamometer assemblies along the side of the die would have been difficult, the pressure distribution was obtained in successive tests in which the distance from the gauge to the bottom of the compact was adjusted to different values by changing the length of the bottom piston. The dynamometer, disassembled from the die, was calibrated under compressive loads and showed a 1.00 ohm change of resistance for every 15,300 psi change of pressure (750 lb load change). All the strain gauge measurements were made with a null type Leeds and Northrup Wheatstone bridge. The sensitivity of the method was better than 1 pct and the accuracy was within 2 pct. These values were considered satisfactory in view of the rather large scatter in the measurements introduced by the random variation in packing the powder in the die. The stable ambient conditions and short time involved in the taking of observations made temperature compensation unnecessary-. The pressure distribution on the bot-

Jan 1, 1950

By Leon O. Hart

The nickel-chromium alloys of importance are those containing iron and those free from iron. The most important alloys containing iron, with regard to high tonnage, are the nickel-chromium steels. Straight nickel steel was introduced about the year 1889, but it was not until 1895, when it was found that the addition of chromium greatly increased the strength and resistance to shock, that nickel-chromium steels came into use. The three types of nickel-chromium steels developed at this time were: Type 1, containing 3.,50 per cent. nickel and 1.50 per cent. chromium; type 2, containing 2.00 per cent. nickel and 1.00 per cent. chromium; and type 3, containing 1.50 per cent. nickel and 0.50 per cent. chromium.

Jan 1, 1921

By J. Chipman, N. J. Grant, B. M. Shields

The vacuum tin-fusion method of analysis for hydrogen, developed by Carney, Chipman, and Grant, has been modified to permit the analysis of the evolved gases for hydrogen by means of a thermal conductivity cell. A properly prepared sample can be analyzed in 10 min with a probable error of ±0.12 ppm. A study of various methods for storage of hydrogen samples shows that samples can be safely held in a dry ice-acetone bath as long as six days. Storage in liquid nitrogen is necessary for samples to be held one week or more. HE vacuum tin-fusion method, as developed by I- Carney, Chipman and Grant,' is the only analytical procedure which has shown promise of being fast enough for use in the control of hydrogen during steelmaking. It was felt that further simplification and faster speed of operation could be effected by the use of thermal conductivity measurements for analysis of the gases evolved in the tin-fusion method. The application of conductivity measurements to the tin-fusion method is possible because: 1—the evolved gas is essentially a mixture of hydrogen, nitrogen and carbon monoxide with a hydrogen content usually over 50 pct, 2—the evolved gas is collected at a relatively low pressure, and 3— the thermal conductivities of CO and N2 are practically identical while that of hydrogen is very much greater. The major part of this research program was devoted to the construction and calibration of a vacuum tin-fusion apparatus which analyzes the evolved gases for hydrogen by means of a thermal conductivity cell. The second phase of the problem was associated with the development of a procedure for storage of samples prior to analysis. With the rapid quenching method for hydrogen sampling,' which seems to be the most practical for steel mill use, it is necessary that the samples be stored safely during the interval between sampling and analysis if the hydrogen content of the molten metal is to be maintained in the supersaturated solid samples. The thermal conductivity bridge has been used for a number of years in the analysis of certain gas mixtures. An elementary discussion of the theory and practice of gas analysis by thermal conductivity measurements is given by Minter.3 A more comprehensive discussion of the theory and of the various measuring circuits is presented by Daynes.' A complete knowledge of the theory and properties of the thermal conductivity of gases and gaseous mixtures can be gained by a study of the standard textbooks on the kinetic theory of gases."' The existing data on the thermal conductivity of single gases are reviewed by Hawkins: that for a number of binary gas mixtures by Daynes' and Lindsay." The thermal conductivity method may be applied to the determination of the composition of a binary mixture if: 1—the thermal conductivity of the mixture varies monotonically with composition, and 2— the two gases have measurably different thermal conductivities. The greater the difference between the two gases, the greater the sensitivity of the method.10 he method is applicable to the analysis of multicomponent mixtures when all of the gases in the mixture except one have nearly the same thermal conductivity. Fortunately, the mixture of hydrogen, nitrogen, and carbon monoxide evolved by the tin-fusion analysis' falls in this latter classification. The thermal conductivities of nitrogen and carbon monoxide are practically equal; and the thermal conductivity of hydrogen is approximately seven times that of the other two. Therefore, the thermal conductivity of a gaseous mixture of hydrogen, nitrogen, and carbon monoxide at known temperature and pressure can be related directly to the percentage of hydrogen in the mixture by suitable calibration. Usually the thermal conductivity of a mixture of gases is measured at atmospheric pressure where the thermal conductivity is independent of pressure over a wide pressure range. At very low pressures (below 1 mm Hg), the thermal conductivity of gases varies with the pressure. This phenomenon has been utilized in the Pirani vacuum gage for the measurement of pressures in the range of 10" to 10-0 mm of mercury.= Very little has been published concerning the variation of thermal conductivity with pressure at intermediate pressures between 1 mm Hg and 1 atm. However, preliminary measurements indicated that the thermal conductivities did vary with pressure over the range of pressures (up to 10 mm Hg) at which gases are delivered from the vacuum pump. Therefore, the calibration of the thermal conductivity cell had to be planned to include the effects of both gas composition and pressure. Such a calibration chart is shown in Fig. 4. Most industrial applications of the thermal conductivity method of gas analysis have used a compensated Wheatstone bridge circuit containing two

Jan 1, 1954