Search Documents

By Thomas M. Turner

Open pit mining, always a demanding task, faces two relatively new problems today: (1) availability of equipment and (2) environmental restrictions. The modern dredge offers relief in both problem areas. Delivery on a major dredge might run 18 to 24 months rather than 60 months; and lowering of the water table is precluded, thus minimizing environmental objections. In addition, a lower first cost and potentially increased efficiency may offer real advantages to the miner who is forced away from his traditional mining methods. What are the objections to the use of a dredge in open pit mining? Perhaps first and foremost is the natural reluctance to change from a successful operation. Who can blame the miner who has developed expertise in the use of the dragline if he is reluctant to change to a new mining technique that requires new and different skills? A part of the same problem is the miners' desire to control the excavation visually in order to delineate sharply between overburden and matrix. This problem can be alleviated significantly by utilizing good boring data and a positive acquisition cutter. In the final analysis, however, if the miner is prohibited from dewatering the area, either he mines the deposit by dredge or not at all. There is little doubt that when the decision is made to remove overburden and/or matrix by dredge, the problems of delineating between overburden and matrix, creation of slimes, and development of mining plans to minimize double handling etc., will be addressed and solved. There are two broad categories of dredges: mechanical and hydraulic.

Jan 1, 1976

By George Jones

MACHINE mining on the pitch plays an important part in the produc-tion schedule at the Salem Hill Colliery of the Haddock Mining Co. This mine is just outside the city of Pottsville, in Schuylkill County, along the southern border of the Anthracite Region. The entrance to the mine is through a cross-measure tunnel 15 ft. above water level and running north 1500 ft. until it strikes the Rabbit Hole vein, where the machine mining is carried on. The main slope, dipping south, was sunk 1200 ft. in the Rabbit Hole vein with levels turned off at 300-ft. intervals. The vein is from 24 to 30 in. thick on a varying pitch of 20° to 40°. The overburden has differed from 50 to 466 ft., the most recent work having the maximum overburden. Immediately over the Rabbit Hole vein is a seam of soft sand slate from 1 to 4 ft. thick which presents a problem at times because it dis-integrates rapidly when exposed to the air. It will crack up and fall without any audible warning, therefore the workmen must always be on the alert, watching for loose slabs. The main top is sandstone, vary-ing in thickness from 8 to 20 ft. The bottom rock is similar to the top, but is finer grained and subject to a more complete disintegration. The vein has a 3 to 4-in. shelly band along the bottom, and all under-cutting has been done in this soft band.

Jan 1, 1935

By R. W. Heckel

The conzpaction of metal powders is analyzed through density-pressure curves as a three-stage process — die filling, individual particle motion, gross compact deformatim. The densification occurring during each of these stages is evaluated quantitatively. The amount of densification in the first and second stages is primarily a function of particle geometry. The densification taking place in the third stage is dependent mainly upon the material. AT the present time the densification of powders during compaction is usually described by terms such as "compactibility," "compressibility," and "compression ratio." Schwarzkopfl has proposedthat compactibility be defined as the minimum pressure needed to produce a given green strength, while compressibility be used to indicate the extent towhichthe density of a powder is increased by a given pressure. Compression ratio is generally defined as the ratio of the compact density obtained at a given pressure to the apparent density of the loose powder. 13alshina found that the pressure imposed on a compact affects the relative volume of the compact according to the following relation: hP= - LV + C [ll where: P is the applied pressure, V is the relative volume of the compact, Ratio of the specific volume of the compact to that of the material without porosity. Lisa constant described as the modulus of pressing and is determined by the slope of a plot of h P vs V, and C is a constant which is determined by the intercept of a plot of InP vs V. Several drawbacks of the Balshin analysis may be noted from Fig. 1, which is a plot of pressure (loga-

Jan 1, 1962

By G. H. Rowe, A. N. Stroh, D. P. Gregory

The magnitude and variation with strain of the parameters activation volume, V*; activation energy, H; and frequency factor, A, in the Arrhenius equation for strain rate are determined for colunlbium single crystals and polycrgstals. Comparison of dislocation structures in deformed columbium crystals as determined by transmission electron microscopy with the rate IF deformation of a metal crystal is a thermally activated process, rate theory can be used as a powerful tool in the study of dislocation mechanisms. seeger1 develops the following expression for plastic deformation governed by a single thermally-activated theory results suggests thai formation of lattice vacancies at jogs in screw dislocations is responsible for thermally activated deformation of poly crystalline columbium. Single crystals appear to deform by a different mechanism. Work hardening in fully recrystallized fine grain columbium is found to result from simultaneous decrease in activation volume and in the number of mobile dislocations with increasing strain. Work hardening in recovered polycrystals is found to result from decrease in activation volume with strain only. dislocation mechanism. His equation for strain rate is where N is the number of mobile dislocations per unit volume held up at energy barriers, v is the frequency with which the dislocations "try" the energy barriers, b is the Burgers vector, a is the area a dislocation loop sweeps out after overcoming a barrier, V* is the activation volume which will be defined more completely later, and t* is the thermal component of stress equal to (Ta-Ti), where Ta is applied shear stress and Ti is internal stress of the dislocation network17' given by

Jan 1, 1963

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By Strathmore R. B. Cooke, Emert W. Lindroos, Norman F. Schulz

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by' flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (--CH2CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder[4] has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate-potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality.

Jan 1, 1952

By John Wulff, Robert Kamm, M. A. Steinberg

IN a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described, In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was, found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region -of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. CIRCULAR-HOLE GRIDS AND ANALYSES OF RADIOGRAPHS Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in, centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1,125 in. in diam and the clearance between plungers and die wall was 0.001 in, The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value on an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1948

By R. G. Wayland

SINCE the installation at Kropfmuehl, Bavaria, of a modern flotation concentrator in 1938, the flake and fine graphite from the Passau area can now be delivered in about any normal specified carbon content of any size range up to a flake averaging about 0.7 mm. The graphite finds a wide German and export market for crucible manufacture, pencil leads, dry cells and other uses. A controversy over the origin of the graphite deposits is being resolved in favor of syngenesis rather than epigenesis. The syngenetic theory is newly supported by the yet unpublished work of Hartmann of the Bavarian Geological Survey. Development work and exploration for graphite in the area may be changed in direction as the syngenetic theory is accepted. Crystalline graphite is produced in the area east of Passau near the junction of Germany, Austria and Czechoslovakia, as shown in Fig. 1. This is the only graphite area of importance in Germany, and Gra-phitwerk Kropfmuehl AG is the only operating firm in the area. The plant and mine are located at Kropfmuehl near Hauzenberg, Kreis Wegscheid, about 10 miles east of Passau. A narrow gage railway from the mine connects with the German Railway at Schaibing Bahnhof. The Pfaffenreuth mines date from about 1730. Until the early 20th century mining operations were carried out in a haphazard fashion. During World War I graphite mining and milling was increased, since it had to cover almost all of the crucible needs of the Central Powers. Between the wars some 11 mines were operated by two large and several small companies, but under the Nazis these were consolidated by 1938 into the Kropfmuehl enterprise. Kropfmuehl built a modern flotation mill to treat its own ores and small amounts of custom ores and tailings from the area. Since Graphitwerk Kropfmuehl AG was an I.G. Farbenindustry subsidiary, it has been under Military Government Property Control and probably will be sold to private German capital. Geology The country rock of the graphite area is part of the "kristallines Grundgebirge," the series of old gneissic and schistose rocks that constitutes the bed rock of most of the Bohemian basin and rims the Sudeten-land. The gneissic rocks of the graphite area are considered to have been metamorphosed during the Carboniferous period. They are bordered on the north by granite stocks and penetrated by numerous smaller granite and pegmatitic intrusive rocks, as shown in Fig. 1. The gneiss is classed as a micaceous, coarse-grained cordierite gneiss by most investigators. It is much metamorphosed by the granite, particularly in the north near the larger granite bodies. Interbedded in the gneiss are the graphite seams and lenses, and also beds and lenses of crystalline limestone containing disseminated graphite in noncommercial quantities. The gneiss, together with the included graphite and limestone seams and lenses, is cut and displaced by a number of granite sills of medium to fine grain and by a large number of diorite lamprophyre dikes and a few syenite-pegmatite dikes. The lamprophyre dikes are of various mineral compositions and textures, but many are banded and richly impregnated with pyrite; while the syenite-pegmatite dikes are coarse-grained with good crystals of titanite, pyroxene, uralite and other green amphiboles. Most investigators and the miners speak only of diorite and granite dikes cutting the graphite seams. The diorite dikes are later than the granite and some of the faulting, as is evident from Figs. 1 and 2. Individual graphite seams and lenses may be mined for thicknesses of several feet up to several scores of feet, and for distances of several hundred feet. The aggregate thickness of a series of some 20 seams of graphite, limestone and interbedded gneiss at Kropfmuehl is stratigraphically about 450 ft. Laterally, the graphite in a seam may pinch out or grade into crystalline limestone. Graphite crystals also are found disseminated in the gneiss itself, although in unmineable concentrations. The faults that cut the graphite seams carry graphite for some feet or tens of feet away from the seams, apparently mechanically. Similarily, the graphite lenses themselves often contain mechanically introduced inclusions of wall rock, probably from flowage during folding. Graphite crystals make up 10 to 30 pct of the fresh, mineable graphite lenses at Kropfmuehl, averaging about 20 to 25 pct after hand-sorting by the miners. In weathered lenses, the graphite concentration is said to be as high as 50 pct. The associated primary and hydrothermal minerals are dom-inantly feldspar and calcite, plus quartz, pyrrhotite, pyrite, biotite and occasional garnet, hornblende, sphalerite and galena. Associated secondary minerals include kaolin, nontronite, mangano-oxide-silicates (mog), adularia and chlorite. The superimposed suite of siliceous cementation minerals present consist largely of opal, chloropal, chalcedony, jasper, and hyalite. The kaolin is of special interest since it too was mined as early as 1730 and was used in the well-known Nymphenburg porcelain from 1756 on. The kaolin is derived from the gneiss and the syenite pegmatites. The crystals of graphite vary in size within a given seam, but in seams more than a mile away from the granite on the north the average crystal-linity is less coarse, lowering the commercial value. The lenses in the Kropfmuehl-Pfaffenreuth area are the most developed, and are the only ones with deep workings now accessible. Other similar crystalline graphite lenses are known from older workings at Habersdorf, Oberoetzdorf, Ficht, Diendorf, and

Jan 1, 1952

By M. J. Pool

The partial molar heats of solution in liquid tin of cadmium, silver, tellurium, and zinc have been measured at 655°. 700°, and 750°K by liquid-metal solution calorimetry. Silver, cadmium, and zinc are endothermic at these temperatures while tellurium is exothermic. Only the heat of solution of silver depends on composition while all four elements show a temperature-de pendent heat of solution. The heat of solution of tellurium is constant up to 0.6 g-at. pct, becomes increasingly more exothermic, and reaches a limiting value at 1 g-at. pct Te. The limiting value has been used to calculate the heat of formation of SnTe at 750°K. The heat effects associated with the dissolution of the compounds Ag2 Te, CdTe, and ZnTe in liquid tin were measured at 750°K. These values are cotnOined with the measured hat effects at 750°Kfor silver, cadmium, tellurium, and zinc to detertrline the heats of formation of the telluride compounds. Cadmium lelluride exhibits a heat of dissolution which has a compositional dependence. THERE is a considerable amount of interest in the compounds of tellurium because of their electronic properties. Both cadmium and zinc tellurides are thermoelectric materials and considerable work has been done on their electronic properties but a limited amount of data is available on their ther-modynamic properties. This work was undertaken to elucidate the heat of formation data on cadmium and zinc telluride. Since both cadmium and zinc are in Group II it seemed to be of interest to compare the values obtained for them with the heat of formation of a Group I telluride. Silver telluride was selected for this comparison. In the course of the work it was also possible to determine the heat of formation of tin telluride and therefore to make a comparison of some of the Group I, 11, and lV tellurides with the metallic elements silver, cadmium, and tin being in the same period. There is also a great deal of interest in the energetic changes which occur upon addition of solute elements to a common solvent. This investigation provided an opportunity to study the partial molar heats of solution of silver, cadmium, tellurium, and zinc in liquid tin. The partial molar heats of solution are of theoretical interest because solute-solute interactions are a minimum in dilute solutions and application of solution models is simpli- fied. In order to complete the analysis of solute-solute and solute-solvent interactions the temperature dependence of the partial molar heats of solution was also measured. MATERIALS AND EXPERIMENTAL PROCEDURE All materials were of the highest purity available. The silver, zinc, cadmium, and tellurium were obtained from American Smelting and Refining Co. and were reported to be 99.999 pct pure. The silver telluride, zinc telluride, and cadmium telluride were obtained from Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp., and were electronic-grade material of 99.999 pct purity. Tin used for the solvent bath and for calibration was obtained from the Vulcan Manufacturing Co. and was reported as being 99.99 pct pure. The liquid-tin solution calorimeter used in this work is similar in principle to the differential twin-type calorimeter described by K1eppa.l Two of three identical calorimeter wells are used together during any set of experiments, one well being active and the other being passive. The wells are positioned 120 deg apart in an aluminum calorimeter block. Each well contains a multijunction thermopile and a Pyrex test tube to hold the liquid metal bath. Forty-eight of the thermopile junctions are distributed over the surface of each calorimeter well adjacent to the test tube and serve to integrate the heat effects occurring. The other forty-eight are next to the aluminum calorimeter block. The thermopiles for the three wells are connected differentially so that any change in temperature at the outer junctions (which will be the same for both wells because of the high conductivity of the aluminum block) will oppose for the two wells and result in no shift of the zero. The electrical output represents the true temperature difference between the two reaction vessels. A reaction occurring in the active well gives a comparison with another body of very similar thermal properties. In this way, any spurious heat effects due to slight temperature drifts within the entire calorimeter block are eliminated. The output of the differential thermopile goes to a dc amplifier with multiple ranges of from * 10 pv to 1 30 mv. The output of the amplifier is then fed into a Leeds and Northrup strip-chart recorder. The adiabatic temperature change is then calculated using the technique of Howlett, Leach, Ticknor, and ever.' The aluminum calorimeter block is contained in a cylindrical furnace with main and control heaters

Jan 1, 1965

By Paul F. Kerr, Raymond F. Robinson

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 * 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre Cambrian. THE Sunshine mine in the Coeur d'Alene district, Idaho, is well known for its silver-bearing veins but prior to the summer of 1949 had not been recognized as a possible source of uranium. At that time, during a geiger counter reconnaissance by T. E. Gillingham, R. F. Robinson, and E. E. Thurlow, high radioactivity was noted and radioactive specimens were collected from the footwall of the Sunshine vein.' The detection led to the identification of uraninite-bearing veins, since explored jointly by the Atomic Energy Commission and the Sunshine Mining Co. After the occurrence was noted, the geology of the uranium deposit was studied by the Sunshine staff, and a laboratory examination of the ores was conducted at Columbia University. Several types of laboratory work were undertaken. Differential thermal curves were made of selected siderite samples and results from many more were secured through the work of Mitcham.2 X-ray diffraction and X-ray fluorescence analyses were employed on uraninite, jasper, and siderite. Chemical analyses were made through the cooperation of the Division of Raw Materials of the Atomic Energy Commission. General Geological Features Several silver-bearing veins cut the overturned north limb of the Big Creek anticline as mapped by Shenon and McConne1,³ while the Osburn fault, a long-recognized regional feature about a mile away, marks the north boundary of the Silver Belt. The Sunshine vein, Fig. 1, has a south dip more or less parallel to the 60" axial plane of the fold and cuts rocks of the Belt. Series, starting with the Wallace formation near the surface, continuing downward through the St. Regis formation, and probably extending into the Revett quartzite which lies below the bottom or 3700-ft level. The limb of the anticline is locally modified by secondary folds, one being prominently exposed in the uranian area along the Jewel1 crosscut near the Sunshine vein. Crumpling of the limb resulted from compression which formed the anticline and probably preceded the faults in which the vein deposits accumulated. Evidence of drag along these faults points to reverse movement in the uranium-bearing area and elsewhere. This is true of major faults in the mine workings, and the majority of faults which can be mapped, as pointed out by Robinson.' The St. Regis formation, as measured in the mine, appears to have an initial thickness of some 2000 ft, but the apparent thickness due to thickening during folding is some 3400 ft. Along the Sunshine vein the purple and green rocks characteristic of the Wallace formation in the nearby Military Gulch section p. 37 of ref. 5) have been completely bleached because of introduced sericite. Hydrothermal solutions acting on the wall rock have substituted for the original color a pale greenish cast, although no pronounced mineralogical change has resulted, as Mitcham has observed.' The silver and the uranium depositions appear to belong to distinct epochs resulting from several periods of emplacement. Likewise, multiple periods of deformation account for the faulting. Uraninite is generally associated with silicification, while silver . mineralization accompanies carbonate veins. Rarely, uraninite may be found in a matrix of siderite. Ordinarily uraninite formed prior to ar-gentian tetrahedrite. Where clusters of veins form a stockwork, uraninite-jasper veins often favor one trend while tetrahedrite-siderite veins favor another. During deformation, brecciation of the St. Regis quartzite provided openings between broken rock fragments for precipitation from vein-forming solutions. Fractures due to major breaks were filled during the first stages of vein formation, while later deformation displaced the first veins and provided new channels along which further mineralizing solutions proceeded. The uraninite veins, as the first formed, have suffered fracturing, displacement, and segmentation. Uranian vein segments uncut by faults and more than a few feet in length are rare or nonexistent. Siderite veins are more massive and often extend without a break for tens and even hundreds of feet. In general they show much less segmentation. While the siderite is usually later, there is an overlap in the periods of deposition, some earlier siderite veins being extensively segmented in much the same way uraninite veins have been broken. Vein silica is more extensively distributed than the uranium and iron mineralization it carries. Along the vein course concentrations of uraninite frequently fade away and barren white quartz continues, the transition often occurring within a few feet along strike or down dip. An example appears on the 3700-ft level where a uraninite vein, see Fig. 2a,

Jan 1, 1954

By Benny Langston, Frank M. Stephens

Although little information is available concerning small-scale equipment for dust collection in laboratories, it is possible to adapt standard equipment for laboratory use. Dust from laboratory processes may be collected by cyclone separators, filters, electrostatic separators, scrubbers, and settling chambers. IN recent years much attention has been given to recovery, treatment, and disposal of dusts discharged into the atmosphere from operations of industry. considerable data has been accumulated on both operation and design of dust-collector equipment for commercial installations. On the other hand, there is almost no published data on design and construction of small-scale equipment to handle dust problems that arise in the ore-dressing laboratory. Dust-collection equipment such as multiclones, single-cyclones, scrubbers, chemical and mechanical filters, settling chambers, and electrostatic separators has proved its efficiency for collecting dust in industry. In the laboratory, however, the engineer is faced with the problem of collecting small quantities of dust, inexpensively, without diverting the major effort from the metallurgical problem to the problem of collecting dust produced by the process. For most applications standard dust-collection equipment is too large for use in the laboratory; however, for control of dust in large working areas it is often possible to use a standard dust collector, such as an air filter, with branch ducts to eliminate a health hazard. For example, the well-furnished sample-preparation room containing small jaw crushers, rolls, and pulverizers, in addition to the riffles and screens necessary for preparation of samples, presents a perennial source of dust. The authors' experience has shown that a combination system consisting of overhead branch ducts to the individual equipment and floor ducts with grills, where applicable, connected to a central dust collector effectively removes dust generated in preparation of samples. Fig. 1 is a sketch of a downdraft dust-collector for table installation. Similar systems can be built with floor grids. For portable equipment such as laboratory vibrating screens this type of installation with a steel grill to support the heavy load is reasonably efficient. Overhead branch ducts to individual crushing and grinding equipment, although efficient, must be carefully controlled by dampers to prevent excess loss or a change in the composition of the sample. Change in sample composition can result from excess velocity, which causes selective removal of constituents of low specific gravity. Fig. 2' shows the theoretical effect of terminal velocity on spherical particles of different specific gravities in air and water under action of gravity. Fig. 3 shows the effect of air velocity on composition of CaCO, coal mixtures. Although the entrainment of dust particles in a moving air stream is the basic mechanism by which all dust-collection equipment functions, usually intake velocity of the dust-collection system must be controlled to prevent loss of part of the sample. As an example of what may happen when excess velocities are used, a mixture of 50 pct coal and 50 pct limestone was crushed to —10 mesh and fed to a pulverizer equipped with an overhead dust-collection system. Fig. 4 shows the overhead dust-collection equipment used in this test. The pulverizer was set to give a product 95 pct —100 mesh in two stages. Velocity of air passing over the lip of the pulverizer was measured with an anemometer. After grinding, the finished product was analyzed to show the amount of calcium carbonate present. Fig. 3 shows graphically the increase in calcium carbonate as velocity through the dust-collection duct was increased. These data show that at a velocity of 1 ft per sec little if any of the coal was entrained by the overhead draft. At the maximum velocity, about 6.5 ft per sec, approximately 7 pct more coal was entrained than calcium carbonate. From an operating standpoint, this problem can be remedied easily by dampering the line to control velocity. The lowest velocity commensurate with satisfactory dust control should be used to prevent excess loss and, in some cases, selective dust loss. Collection of Dust in Laboratory Processes As in industry, the engineer desires to collect efficiently the dust produced by processes being investigated on a laboratory scale. However, in the collection of laboratory dusts he is faced with two additional problems: 1—The volumes of gas and the quantity of dust that must be recovered are small when compared with the capacity of standard dust-collector equipment, which must be scaled down in design except for collection of dust from large pilot-plant operations. 2—In addition, because of the variety of problems studied in the process laboratory, the engineer cannot design today a dust collector that will meet the conditions imposed by the processes of tomorrow. Sometimes, therefore, he must compromise collection efficiency to minimize the cost of fabrication and the amount of time diverted from the metallurgical to the dust-control problem. For collection of dust from laboratory processes a cyclone separator, filters, electrostatic separators, scrubbers, and settling chambers can usually be adapted for small-scale operations. The following

Jan 1, 1955

By Frank V. Hicks

THE following paper-in no sense a technical paper-is a summary of a safety campaign instituted by a coal-mining company to improve an unfortunate safety record. The experience should be suggestive equally to coal and metal-mining companies. With few precedents to follow in the beginning, the course was charted by trial and error. The endeavor, often disheartening, finally resulted in the capture of the most coveted safety trophy in the mining industry, "The Sentinels of Safety," awarded by the Hercules Powder Co. of Wilmington, Del., through the U. S. Bureau of Mines. The period described covers the 10-year interval, 1924 to 1933, the year 1933 being that for which the award was made. The coal company considered has produced annually for a number of years an average of 2,750,000 tons of coal, employing at various times from 1.800 to 3000 men. Prior to 1924, the

Jan 1, 1935

By C. G. Rhodes

A technique for producing etch pits in uranium monocarbide has been developed. The pits, which are assumed to be associated with dislocations, appear individually and as arrays delineating sub-boundaries, as seen in Fig. 1. The samples used were single crystals prepared by the technique described by Nadler.* Uranium

Jan 1, 1963

By O. B. Hopkins

As prefatory to the body of this paper, a few general statements will be made (1) in regard to the history and importance of the asbestos, (2) as to the principal sources of the raw material, and (3) as to the types and modes of the occurrence of asbestos.

Jan 1, 1915

[Officers and Committees of the Society of Petroleum Engineers 1 Officers and Staff of the AIME 2 . Officers of AIME Sections Predominantly Petroleum in Membership 3 AIME Local Sections and SPE Regional Organization Maps 5 Alphabetical List of Members 7 Geographical List of Members 102 Advertisers' Index 133]

Jan 1, 1961

By AIME AIME

OUR new Director from the 15th District is Robert W. Thomas; of Ray, Ariz., general manager of the Ray Mines division, Kennecott Copper Corp. In electing him to this office his fellow engineers pay tribute to his ability as an engineer and express appreciation for his service to the A.I.M.E. and its Arizona Section. ?Bob? Thomas was born April 1, 1886 at St. James Minn. received his early education in the public schools of Topeka Kans. and was graduted from Topeka High School in 1905. Already he had decided upon mining engineering as a profession. so he entered the mining school of the University of Kanas from which he was graduated with the degree of B.S. in hlining enginrering. While in college he became a Student Associate of the A.I.M.E. After graduation, lution and isolated mining camps wel-e not the most desirable places in w

Jan 1, 1944

By R. S. Dean

BLUE HEAT PHENOMENA IN constructing a theory of the flow and hardening of metals, we necessarily make use of such phenomena as seem to be, universally observed in metals. It is, therefore, a matter of. concern to the constructors of such mnemonic systems if one or two of the group classified as metals show anomalous behavior. Such egregious phenomena are observed in pure or nearly-pure iron in the reaction of its mechanical properties to low-temperature annealing after cold work and to increased temperature of testing. In short it has been generally observed that iron," as an outstanding exception among metals, increases its hardness and strength by low-temperature annealing. after cold work,1 and also by increase of testing temperature to the range of 150° to 300° C. The investigation here recorded was made then with the object of ascertaining if similar phenomena were observed in high purity iron and, if not, to the presence of which impurities these phenomena could be traced.

Jan 1, 1929

University of Alabama University, Alabama Mining and Metallurgical Society STEPHEN STILLWELL, President VINCENT ZENOBILE, Secretary GEORGE '1 BATOR, Faculty' Sponsor RAY L. FARABEE, Counselor University of Arizona Tucson, Arizona Miners' Society RICHARD BRITTAIN, President FRED W. SHERMAN, JR., Secretary J. B. CUNNINGHAM, Faculty Sponsor E. P. GARDNER, Counselor

Jan 1, 1943

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953