Search Documents

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

Christmas Island "C"-grade phosphate consists essentially of the minerals crandallite and millisite. Although containing over 25% P205, this material is not suitable for the manufacture of water-soluble phosphate fertilizers by conventional processes, because of its high iron and aluminium content Cover 25% total R203). In order to produce a water-soluble fertilizer from such material it is necessary to separate the iron and aluminium from the phosphate, which must report in a product acceptable as a fertilizer. Several processes were studied in detail. The first used ion exchange for dissolution and separation and yielded diammonium phosphate; processing costs were high compared with conven- tional processes based on apatite. The latter processes have basically simple flowsheets and cost of processing is low when compared with the costs of the raw materials. The need to separate iron and aluminium from the phosphate introduces additional complexity into the treatment of the C-grade material. The higher processing costs might be justified, however, if alumina could be produced as a byproduct. Two proposed processes have been developed in which: 1. hydrochloric acid is used for dissolution, and solvent extrac- tion for the separation of ferric chloride from phosphoric acid. Aluminium chloride is precipitated and hydrolysed to recover alumina and hydrochloric acid. 2. sulphuric acid is used for dissolution and aluminium is crystallized as ammonium alum. The phosphate is produced as an ammonium phosphate-sulphate fertilizer. High purity alumina can be obtained by treatment of the recrystallized alum. The technology of these processes is described, and their broad economics discussed briefly.\

Jan 1, 1971

By M Brewster

Goldfields Abosso Goldfields Limited (AGL) is a Ghanaian registered company that owns and operates the Damang Gold Mine. Gold Fields Ghana Holdings Limited holds a 71.1 per cent interest in AGL. The Damang concession held by Gold Fields Ghana Holdings Limited covers a total area of 271 km2 located 40 km north of the town of Tarkwa in the south-western part of Ghana. Gold Fields as a company registered on the New York Stock Exchange is legally obliged to be SOX (Sarbanes-Oxley). Sarbanes-Oxley Section 404 (SOX404) is on management assessment of internal controls. The Mineral Resource Management (MRM) function of AGL manages three Prospecting Licenses and two mining licences. At least ten pits/prospects are scattered along the two limbs of the Damang Anticline and have two main types of mineralisation notably Paleoplacer and Hydrothermal. Thus SOX404 procedures are put in place to treat each mineralisation type in the best way for reliable resource outputs and estimates. Generating auditable resources for AGL is a prime but most important function of MRM. Thus important checks are built and designed to ensure that all relevant geological and geostatistical inputs conform to procedures outlined under SOX404 requirements. More importantly sign offs are designed to ensure that technical personnel involved in all aspects of resource and reserve generation are satisfied and can be held accountable.

Jan 1, 2007

As the Mount Morgan electrolytic chlorine plant is the first of its kind installed in Australia, and as the details of this method of producing chlorine have, up to the present time, been kept more or less secret all over the world, the author trusts that this paper may fill a gap in the technical literature of the subject.When an electric current is passed through a strong solution of sodium chloride the following reaction takes place -2 NaCl + 2 H 20 = 2 NaOH + C1 2 + H 2 Chlorine gas is liberated at the anode or entering pole of the current, while caustic soda and hydrogen are formed at the cathode or leaving pole of the current. If the two electrodes be simply immersed in a vessel containing salt and the current be turned on, there will be no result save slight smell of escaping chlorine gas. The passage of the current will have certainly split up the salt water according to the above equation, but as the products would be in juxtaposition they would immediately reunite, and the electrical energy would have been spent without any beneficial result having been obtained. Therefore, the all-important problem in designing an electrolytic chlorine cell is the finding of some effective means of isolating from each other the chlorine and caustic: soda as soon as liberated from the...

Jan 1, 1911

An efficient stores organisation is essential for an efficient undertaking. Unless the stores organisation is able to meet the requirements of its requisitioners promptly and economically, the undertaking as a whole cannot function efficiently.Delays or errors in supply of material, or substitution due to lack of material availability from the stores are costly and must be eliminated. This then makes the objective of a store, to supply on demand at the cheapest possible price, those items of stock which it is organised to carry, also to procure as quickly as possible and at the lowest price those special items required which are not normally carried in stock. To do this it is necessary to set up a stores organisation consistent with the size and requirements of the undertaking. Stores organisations vary with the nature of the undertaking they are designed to serve. In the case of the Broken Hill Associated Smelters Pty. Ltd., an organisation has been established to meet the operating and maintenance requirements of the Port Pirie Works. These embrace the particularly wide range 0:1; activities associated with roasting" blast furnacing and refining the lead concentrates from the Broken Hill Mines in a continuous metallurgical process producing a variety of refined metals; also many associated activities including power production and engineering maintenance and construction.

Jan 1, 1951

By See J. B

The zinc-nickel alloy process, TECHNIGALVA, was developed for the control of the thicknesses of zinc -coatings on reactive silicon-killed steels. These are steels containing between 0.04 and 0.15 per cent silicon which have become more common in recent years as more steel is produced by continuous casting. The introduction to this paper will review the current status of this process in Europe, North America and Australasia. It is well known that the presence of silicon at certain levels in steel can cause sufficient growth of intermetallic phases during galvanising to form a grey coating of excessive thickness. This type of coating is undesirable because it is brittle and has poor adhesion to the steel base. Since the early-1980s a widely accepted practice for suppressing the reactivity of steels containing silicon during general galvanising has been the addition of approximately 0.1 mass per cent nickel to the galvanising bath ie the TECHNIGALVA process. The paper will also discuss metallurgical aspects of the use of nickel in galvanising such as the mechanisms by which nickel suppresses reactivity, the structure and composition of the ternary Zn-Fe-Ni drosses formed when using nickel and the use of nickel in the galvanising bath at a level of about 500 ppm to give thinner, smoother and brighter coatings on steel.

Jan 1, 1993

By Lysnar R, Horswill M

Since the introduction of the pocket calculator, electronic measuring equipment, lasers and computers, the mine surveyor's approach to his work has changed. Where he once used steel bands he now uses infra-red, visible light or radio waves. The reading and storing of angles is done automatically and he now has to be familiar with the facilities that a computer can offer, instead of plotting and calculating manually. This highly sophisticated equipment is continually being upgraded, modified and fine tuned. This paper will attempt to highlight some of the equipment at present in use by the surveying profession and research currently being conducted by the WA School of Mines. The various options in EDM will be considered including the latest unit capable of measuring distance without the benefit of a reflector, thus enabling the surveyor to co-ordinate points that were previously thought inaccessible. The School is currently working on changes to the GAK1 Gyro Theodolite which may improve results and enable the operator to have more control and confidence in his observations. Areas under consideration are improved lighting, binocular viewing and interfacing the instrument to a stopwatch. In the last few years the computer is being used not only for surface pickups and control but also for underground work. We will highlight the underground options in this area and the software available.

Jan 1, 1987

While South Africa is well endowed with mineral resources, it is generally accepted that its future will be determined more by the development of its human resources than its mineral wealth. The country has throughout its modern history suffered from an over-supply of unskilled labour and a shortage of skilled and professional manpower. There has furthermore always been an over-reliance on Whites as an internal source of professional manpower, supplemented by immigration wherever possible. Better utilisation of other population groups in professional positions has been hampered by the general lack of education and training among such groups. Although many problems still remain, there are emerging trends which are likely to positively affect the training of professional manpower in the future. The direct and indirect influences that are likely to affect professional training at the macro level include 1. government policy and objectives in respect of manpower education and training, 2. the emergence of technikons as fully- fledged tertiary education institutions, 3. demographic trends in South Africa as they pertain to education, 4. political and statutory developments in the country, 5. industry involvement in tertiary education, and 6. professional registration.

Jan 1, 1986

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. C. H. MARTIN) IN PRESENTING THE CERTIF1CATE TO SIR GEORGE FISHER, C.M.G.Members of The Institute, distinguished guests, of which there are many, ladies and gentlemen, you are welcome.And might I add a special welcome to Lady Mawby and Lady Fisher and to Sir George's only son Peter, who with his wife, Betty and one of Sir George's three daughters, Helen, are present this evening, and also to Sir Maurice's son, Colin, and Colin's wife, Jay, also in our company.The family presence must surely be a great source of pleasure and satisfaction to all those so intimately concerned.It is hardly. necessary for me to state the sole and only rC'l.son for our presence here tonight, which is to conJer on Sir George Fisher and Sir Maurice Mawby Honorary Membership of The Australasian Institute of Mining and Metallurgy, and at the same time to acknowledge two people who have rendered great service to the mining industry albeit tinged with sadness to all of us in the knowledge that from now on their influence may diminish.

Jan 1, 1976

A study is presented of the theoretically possible initiation systems for outbursts and the subsequent propagation mechanism.Previous occurrences of outbursts and their correlation to the theoretical system are described. An estimation of the energy release from two energy sources, gas strain energy and rock/coal strain energy, is presented and the relative importance of each source in the severity of outbursts. Summary: The description of mechanisms of outbursting follows the examination of these phenomena at Collinsville in Bowen No. 2 mine and at Leichhardt Colliery, Blackwater. Quantitative material contained in the paper refers to Leichhardt Colliery, Blackwater. Clearly from the work carried out to date gas release has a major part to play in the out- bursting at both of these collieries. In the case of the December 1 1978 outburst at Leichhardt Colliery energy release estimates place gas strain energy release contributing eight times the energy of that from rock/coal strain energy. Even the normal outbursts at Leichhardt Colliery appear to show this trend. Estimates of energy released are for comparative purposes between gas and rock strain energy and the values obtained may be regarded as approximate.

Jan 1, 1980

Zinc sulphide concentrate from Mount lsa, Australia, was leached in acidic sulphate-chloride solutions using ferric ions as oxidants under atmospheric pressure. The parameters of temperature, particle size and concentrations of ferric and chloride ions were evaluated.The shrinking core model can be used to describe the leaching which is limited by the electrochemical processes in the initial leaching stage, and by both surface reaction and pore diffusion processes subsequently. The apparent activation energy measured in the initial leaching stage is 49 kJ/mole over the temperature range 60 to 90°C.About 99 per cent of the contained zinc in the -45+38 µm particle sample dissolved at 90°C in a 0.5 M H2SO4/0.1 M Fe2(SO4)3/0.8 M NaCI solution within two hours. Some nine per cent of sulphide sulphur was oxidised through to sulphate; the remainder was convened to elemental sulphur.The mixed sulphate-chloride system has advantages over separate chloride and sulphate systems due to the low reagent cost, high leaching rate and possible selective leaching of zinc sulphide concentrate with high lead contents.

Jan 1, 1994

Geological models for the exploration and evaluation of epithermal Au and porphyry Cu-Au deposits rely upon a classification of different deposit styles and an understanding of the evolutionary processes of deposit formation. These models guide the interpretation of subsurface deposit anatomy in order to target drill testing and assist the explorationist to focus on the more prospective projects. It is important for the explorationist to distinguish between different styles of magmatic arc Au deposits as each style displays distinctive characteristics with exploration implications. Magmatic arc Au deposits are distinguished as porphyry Cu-Au formed at depths of 1 - 2 km at the apophysis to larger, buried, magmatic sources which are also the ultimate metal sources for the varying styles of shallower level epithermal Au deposits. Low sulfidation epithermal Au deposits characteristically develop from dilute circulating meteoric waters and are distinguished as the group with a closer relationship to intrusive source rocks, and slightly higher sulfide contents (still generally

Jan 1, 2004

By Ormsby W, Peters M, Van Gils H, Kehprens P, De Boorder H

The northern margin of the Arunta Block is characterized by a metasedimentary and volcanic sequence of lower metamorphic grade than that of the central Arunta Block. Whereas the Harts Ranges have granulite to amphibolite metamor- phic grades, the northern margin only reached greenschist to lower amphibolite facies. Most of the high grade area of the central Arunta Block appears to be unprospective, but the lower grade marginal fringe contains most mineral pros- pects to name a few: Barrow Creek, Molyhill and the Jervois Mine. Numerous smaller prospects occur in this marginal zone. Four major lithostratigraphic units can be recognized in the Jervois Mine area: 1. Gneissic Suite consisting of granitic and rhyolitic gneisses which are characterized by a distinct intersection lineation. 2. Metasedimentary Suite of cordierite- biotite schists and chlorite-biotite schists. 3. Mine Sequence, consisting of spotted schists with andalusite and cordierite, quartz- sericite-feldspar schists with distinct rhyo- litic remnants and quartz-sericite-feldspar schists which contain the lode horizons:

Jan 1, 1984

By Wilson J. R

The main mining method employed at Mt Lyell is sub-level open stoping with a typical extraction level interval of 100 m and sub-level intervals of 30 m. Currently, pillar blasts provide the major portion of broken ore and firings are in the order of 200 000 to 300 000 tonnes while future firings of 500 000 to 300 000 tonnes are planned. Improvement of blasting techniques in these mass firings has been necessary for the following reasons. 1. Extremely wet ground conditions have adversely affected ANFO performance and placed extreme pressure on the charging and priming phases. 2. As pillar blasts increase in size the problems of wet ground conditions are accentuated resulting in very slow loading of wet upholes with cartridged gelignite and unreliable charging of the remainder with ANFO. 3 Fragmentation in pillar blasts has suffered because of the above, result- ing in increased secondary breaking costs and difficulty of extraction.

Jan 1, 1977

A number of cooperative studies have been carried out as preliminary work for drafting a standard for application of granulated slag sand for concrete, and the following conclusions were reached 1 The ten kinds of granulated slag sands pro- duced in Japan satisfy the national standard for fine aggregate in terms of physical and chemical properties. 2 Mortar and concrete tests conducted with granulated slag sand revealed that, although with slight differences in the extent, gran- ulated slag sands used in these tests were applicable'as fine aggregate for concrete, 3 The pumpability test by a concrete pump carried out on concrete with two kinds of now commercially available granulated slag sand demonstrated that the pump pressure feeding is applicable in the same manner as in the case of ordinary concrete. These tests permitted' preparation of a draft standard for application of granulated slag sand, and the results formed the first step toward utilizing this material as a sub- stitute for natural sand.

Jan 1, 1979

PAPERS : 1 COMPUTER AIDED DESIGN OF MINE WATER MANAGEMENT - Z KESSERU 2 THE HYDROGEOLOGICAL PROBLEMS OF GROUNDWATER PROTECTION IN MINING REGIONS - V A MIRONENKO 3 WATER MANAGEMENT OF THE MAE MOH PROJECT -òò SIRI CHITCHOB 4 WATER MANAGEMENT AND WATER TREATMENT AT GOLDPN CROSS - M P A WILLIAMS

Jan 1, 1988

By A E. C Peres, J D. Donda

With the aim of producing a concentrate with silica content lower than 1.0 per cent SiO2, laboratory experiments were conducted using a sample of the final concentrate from the Samarco iron ore flotation plant (mechanical cells circuit). The sample contained 3.08 per cent SiO2. This sample was split in two size ranges: >105 ¦m and 2. The >105 ¦m fraction, representing 23.3 per cent of the initial mass, was re-ground to 100 per cent 2 content were obtained. Considering the mass proportions of the two size fractions, the calculated silica content of the combined concentrate was 0.68 per cent, which is considered satisfactory for the objective of this investigation. The major reasons for the higher (0.90 per cent) silica content of the concentrate from the coarse fraction are the presence of silicon in the lattice of goethite and the presence of residual silicious slimes in the pores of porous hematite.

Jan 1, 2005

By P Alspach, R Buxton, C Morgan, C Ross

Mining companies worldwide have an increasing interest in restoring indigenous ecosystems following mining. Low levels of plant nutrients and organic matter, pH extremes, heavy metals, physically challenging media, and difficult climatic conditions all hinder revegetation of steep rockdump slopes. Our techniques use colonising pioneer plants to accelerate natural soil development and plant succession processes on minesites that are difficult to revegetate with locally sourced plants by traditional techniques. Suitable treatments and pioneer species must first be identified for each rocktype. Field trials at the Stockton Coal Mine in Buller have shown that successful acceleration of moss and pioneer plant establishment is possible. Best plots showed a mean of 15 per cent moss cover and 3.3 per cent vascular cover after 12 months compared with 0.1 per cent and nil respectively for controls. Techniques have been extended to field-scale trials, using hydroseeders and dryblowers. These techniques show potential for practical land rehabilitation, whilst conserving local biodiversity.

Jan 1, 2003