Search Documents

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the tenth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Knott County, Ky., which comprises parts of the Salyersville, Prestonsburg, Troublesome, Hindman, Pikeville, Cornettsville, and Whitesburg quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By J. D. Brown

The electron optics, vacuum system, and sample stage assembly for the Bureau of Mines? electron probe X-ray spectrograph were purchased. Four scanning curved-crystal spectrometers, two reflection- and two transmission-type, were designed and constructed by the authors. The reflection spectrometers are placed in a vacuum chamber for measurement of long-wave-length X-radiation. Detection, pulse-amplitude discrimination, and recording circuits are provided for the simultaneous measurement of four X-ray spectral lines. Minimum spot size is approximately 2 microns in diameter at 30 kilovolts and a sample-to-ground current of 5 x 10-8 ampere. At this voltage and current the limit of detection with reflection spectrometers is less than 0.05 weight-percent for most elements. The limit of detection for elements determined by transmission-type spectrometers, evaluated at 35 kilovolts and 5 x 10-8 ampere, is approximately 0.1 weight--percent for all elements having excitation voltages below 20 kilovolts. In general, reflection spectrometers exhibited satisfactory but poorer resolution than the transmission type, resolution of the spectrometers being limited primarily by crystal imperfections, with greater mosaic structure being introduced by the grinding process for the reflection crystals. Several applications of the electron probe X-ray spectrograph are described. Analysis of a uranium-steel is discussed in detail to illustrate calculation of composition from measured X-ray intensities.

Jan 1, 1962

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By R. V. Higgins

The results of two separate but related studies are given. In the first study, four equations were tested; the object was to determine which would produce a curve that would best fit data points that represent a trend of declining oil production in 90 California fields. Two conventional equations (the Arps and semilog) and two novel equations (extreme-c and double semilog) were tested. The curves were first fitted to the initial 9 years of the 15-year production data and then extrapolated for 6 years to determine how well the extrapolated curve would fit the data points. The generated curves were also extrapolated beyond the last data point to predict rates of future production. The results of the first study showed that no equation was clearly superior to the others in all respects. The semilog equation resulted in the best fit to production data for the first 9 years, but the Arps and extreme-c equations produced a better fit for the extrapolated data for the period of 9 to 15 years. The Arps and extreme-c also gave more realistic production rates when extended to the point where cumulative production equaled reserves. A second study was made to determine if the least-squares technique applied to the Arps equation would result in more accurate extrapolations. The merits of the logarithmic and the nonlogarithmic forms of the Arps hyperbolic equation were also tested. For the logarithmic expression, it was found that one of the constants of the Arps equation reached a value so small or so large that the equation was not applicable to the data of 40 of the 90 California fields. The nonlogarithmic form of the Arps equation was applicable to neither the same 40 fields nor to a few additional ones. When the data and the Arps equation were compatible, the use of the least-squares technique as compared with other methods improved the extrapolation accuracy somewhat.

Jan 1, 1971

By C. M. McCulloch

The natural vertical fracture system in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north-western West Virginia to N 57° W in southwestern Pennsylvania; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures. Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"DIGREGORIO, K. A., E. V. CILENTO, AND R. C. LANTZ. A kinetic model of superoxide production from single pulmonary alueolar macrophages. Am. J. Physiol. 256 (Cell Physiol. 25): C405-C412, 1989.-A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared with experimental results obtained from single rat PAM. The 02 was quantified by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate (NBTH,) from video-recorded images of individual cells. The kinetic model considered three reactions: 1 ) the production of extracellular 02 from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, 2) the subsequent dismutation of 02 to form H,O,, and 3) the reaction of 02 and NBT to form diformazan. NBT specificity for 02 was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) that catalyzes the dismutation of 02 to H,O,. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations because NBT is a relatively small molecule (818 mo! wt) compared with SOD (34,000 mol wt). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/ or electrostatic effects, since SOD is also negatively charged, whereas NBT is positively charged.PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria. This process is accompanied by the production of superoxide anion (02) at the surface of the plasma membrane (3, 31). Superoxide readily dismutates to form H20 2 and subsequently, other oxygen metabolites which have been shown to be both antibacterial and cytotoxic (21, 25, 35).Superoxide is produced from the reduction of extracellular O, at the surface of the cell membrane by NADPH oxidase by the following reaction (3, 4)"

Jan 1, 1989

By Warren D. Longwill

The Bureau of Mines inventoried Federal lands in the State of Oregon and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal status and agency management practices. The Bureau determined areas of the State having past mineral production and/or known metallic mineral resources and areas favorable for coal, oil, gas, and geothermal resources, and prepared maps that spatially compare the availability of Federal mineral land with these mineral areas to demonstrate the extent of restrictions to mineral entry. Oregon contains 62.1 million acres, of which 33.9 million acres or 55% is Federal mineral land. About 2.3 million acres of Federal land is favorable for selected metallic mineral deposits, of which 64% is available, 13% is restricted, and 23% is unavailable. Of the 21.1 million acres of Federal leasable land favorable for oil and gas, 68% is available, 11 % is restricted, and 21 % is unavailable. Of the 146,720 acres favorable for coal, approximately 71% is available, 13% is restricted, and 16% is unavailable. Federal leasable land favorable for geothermal resources amounts to 458,968 acres, of which 42% is available, 34% is restricted, and 24% is unavailable.

Jan 1, 1988

By G. W. Birge, D. E. Wolfson, J. H. Lynch

Fourteen coal samples representing the Flag , Fire Clay , Whitesburg , Amburgy , Upper Elkhorn No. 3 , Upper Elkhorn No. 2 , Upper Elkhorn No. 1 , and Lower Elkhorn beds in Letcher County , Ky . , were carbonized by the Bureau of Mines - American Gas Association ( BM- AGA ) method , and yields of products and physical properties of cokes were determined . The samples tested were high- volatile A bituminous in rank , with dry , mineral - matter- free fixed - carbon contents ranging from 55.3 to 62.2 percent . Five of the samples , as received , were chemically unsuitable for metallurgical use because of excessive ash and/ or sulfur content . Generally , strength indexes of the cokes were low and all of the coals would require blending with higher rank coal to obtain satisfactory blast furnace fuel .

Jan 1, 1964

By G. R. Hopkins, E. W. COCHRANE

The number of completed petroleum refineries in the United States continued to decline in 1937 , but the total capacity to process crude oil continued to increase . These facts were ascertained in the Bureau's annual canvass of refinery capacity as of January 1 , 1938 . Several important changes were made in the census questionnaire for January 1 , 1938 . First , the basis of reckoning cracking capacity was changed from cracking stock charged to cracked gasoline produced . Although this is a definite improvement , in that it is no longer necessary to consider the yield , it is unfortunate that the data for January 1 , 1938 cannot be compared with cracking - capacity statistics since 1925. Other changes or additions included separating capacity at operating plants into that actually operating and that closed down ; collecting data on capacity added or retired during the previous year ; breaking down idle capacity according to physical status ; and separating new capacity into that built for replacement and that built to augment existing capacity . Prior to January 1 , 1938 , the total capacity of an operating plant was listed as " operating " even though some stills might have been closed down ; furthermore , the only capacity reported as being under construction was that of new plants that were being built on January 1. To make the statistics clear , the totals for the United States as of January 1 , 1938 , are given on both the old and the new bases . On January 1 , 1938 , there were 551 completed plants compared with 572 the previous year . Ten new plants were under construction on that date compared with 11 the year before . The greatest number of completed plants recorded was 632 on January 1 , 1936 ; since then , competitive conditions , particularly in the East Texas field , have been instrumental in reducing the number of small independent plants . The total crude- oil capacity of the completed refineries on January 1 , 1938 , was 4,351,151 barrels , of which 3,970 , 196 barrels ( 91 percent ) represented the capacity in actual operation and 380,955 barrels ( 9 percent ) was shut down . The " shut -down " capacity ( 199,875 barrels on the old basis ) was the lowest since pre- depression days , chiefly because numerous idle East Texas plants were removed from the list . The new method of compiling the statistics sheds considerable light on excess crudeoil capacity , which has been the subject of considerable speculation in recent years . The highest daily average crude runs to stills reached in this country was about 3,460,000 barrels in September 1937. At that time , the total crude - oil capacity was about 3,925,000 barrels . This indicates that at peak operation the excess capacity was somewhat less than

Aug 1, 1938

By J. L. Shultz

The Bureau of Mines extended its investigation of methanation catalysts. The noble metals (platinum, palladium, ruthenium, rhodium, osmium) and rhenium), molybdenum, and tungsten were tested in hydrogenations of carbon monoxide and carbon dioxide at 21 atmospheres in a temperature range between 200° and 600° C. From the 8 metals studied) 25 catalysts represent 5 catalyst types were prepared and tested. The impregnated 0.5-percent-ruthenium catalyst proved to be the most active and versatile of all the catalysts produced. Tungsten and the noble metals other than ruthenium were low in activity and usually required temperatures above 500° C for appreciable production of hydrocarbons. Molybdenum was moderate in activity, but further improvement in molybdenum catalysts seems possible.

Jan 1, 1967

By E. J. Matson

From February until July 1943 the Bureau of Mines conducted an exploration project at the Majuba Hill mine to determine tonnage aria grade of the copper and tin ore and to search for extension of the mineralization. The work comprised sampling, long-hole drilling, underground excavation, and ore-dressing test.

Jan 1, 1948

By A. J. Forney

Recent experiments used catalysts of plate assemblies in synthesizing high-Btu gas and gasoline indirectly from coal. A gas with a heating value of 925 to 943 Bt-: per cubic foot has been prod u la the hot-gas-recycle pilot plant from synthesis gas (3H2+100) with lathe turnings used as catalyst in the first reactor, and assemblies of parallel sprayed plats of nickel in the second. Solid plates made of Raney nickel, and steel and aluminum plates sprayed with Raney nickel or nickel oxide were tested. Those catalysts had very low resistance to gas flow; 90 percent lower than nickel granules used in previous experiments. In a single stage of synthesis thee nickel plates were only partially successful. Although the heating values of the product gas ranged from 856 to 941 Btu per cubic foot, the carbon monoxide content of he gas was above 0.1 percent. Both steel and wrought turnings were tested in single-stage synthesis, but the conversion of hydrogen and carbon monoxide was too low to attain the desired heating value of 900 Btu per cubic foot in the product gas. Assemblies of plates thermally sprayed with fusel iron were tried in an experiment to make gasoline. A gasoline yield of 52 percent (of the hydro¬carbons produced) was obtained using a 1H2-10O feed These sprayed assemblies were in service for 1,500 hours, the longest that this type of catalyst has been used. When a second reactor containing Raney nickel catalyst was added in series with the first reactor, complete utilization of the feed gas was obtained because in addition to the liquid product, a high-Btu gas with a heating value of 800 Btu per cubic foot was made.

Jan 1, 1965

By M. C. Irani, Maurice Deul, M. G. Zabetakis, T. G. Bobick

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emission in 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States hid daily methane emissions of 1 MMcfd or more. These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va., which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.3 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1977

By E. R. Cole

One objective of Bureau of Mines recycling research is to devise technology that enables recovery of metals and minerals from wastes. From October 1982 through September 1985, researchers at the Bureau and at the University of Missouri Rolla (contract H0222002) investigated the use of nonferrous flue dust with varying Zn contents (11 to 66 pct) as a source of Zn for electrogalvanizing steel wire. The waste dusts used were from a secondary Cu smelter, a brass smelter, a Pb smelter, and a water treatment plant. The dusts were leached in H2S04, and the leach solutions were treated to make electrolyte for electrogalvanizing steel wire using soluble Zn anodes. Cyclic voltammetry was used in an inno-vative method to evaluate the quality of the electrolytes used for elec-rogalvanizing. After electrogalvanizing, the wire was drawn on a labo-ratory draw bench to simulate industrial practice. Corrosion resistance was measured by a number of electrochemical techniques and by the stan-dard ASTM salt-spray tests. After successful bench-scale tests, the process was demonstrated in an industrial pilot plant. Results indicate that nonferrous flue dusts can be used as a source of Zn for electro-galvanizing if certain impurities are either partially or completely removed from the starting electrolyte.

Jan 1, 1987

By Robert Howard

With the rapid depletion of the Peerless Coal Co.'s mine in Spring Canyon, it was necessary, if the company was to remain in the coal-producing business, to look to the development of a new property or to acquire a mine already developed. After careful investigation of several operating properties it was decided by the officials of the company to take over the lease on an undeveloped acreage held by a private party in Price Canyon, about 3 miles north of Castle Gate, Utah.

Jan 1, 1930