Search Documents

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By Ralph M. Foecking

The disposal of the phosphate slimes produced by Florida beneficiation operations is perhaps the biggest single problem of the phosphate mining industry. This is an old problem which has not been solved and which is becoming increasingly severe. In a typical phosphate mining operation, the phosphate rock mined is initmately mixed with sand and clay, constituting what is known as matrix. During the beneficiation, the clay and other fine materials are separated usually at -150 mesh, and washed from the phosphate rock in a form of diluted slurry known as phosphate slimes. The quantity of slimes solids and their composition vary considerably with the location but usually represent from 25 to 35% of the ore mined. Because of the affinity that clays have for water, large volumes of water are required to separate the granular material in the matrix forming a dilute slime suspension (1.5 to 3% solids) of colloidal material, which settles very slowly, and thus requires immense impounding areas, which never becomes totally usable land. These ponds also contain about 25 to 35% of the total P205 values mined. The magnitude of the problem represented by the slimes can be appreciated better if we realize that there are around

Jan 1, 1971

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By Jeff Poe

When a takeup weight is offset to the side of a conveyor, a wire rope is commonly routed from the takeup weight through a series of sheaves to the takeup carriage. The friction developed from a series of wire rope sheaves can effect the actual belt tension at the make up carriage. Through real-mime testing the actual tension on a makeup carriage was recorded with data acquisition using an internally strain-gauged turnbuckle. The wire rope used to transfer the makeup weight to the makeup carriage was routed through a series of lubricated bronzed bushed sheaves. The tension on the makeup carriage was found to be as much as 26% higher than the weight of the makeup due to the friction in the sheaves. A detailed discussion of the testing and results will be made.

Jan 1, 2000

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By Eduardo M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond grindability data and the operating work index is presented. The objective has been to produce a sand cyclone overflow containing not more than 6% +65 mesh. However, this has never been attained even at low milling rates. On the other hand, significant improvements in throughput were achieved by instituting some equipment changes and process modifications within the grinding circuit. The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1983

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By Malcolm Ross

Fibrous minerals are common in nature but asbestiform minerals are rare. The unique mineralogical characteristic common to all the asbestos minerals is their morphologic form (or habit of crystallization) as polyfilamentous fiber bundles. The individual fibrils within the bundles have a tendency to be very long with a narrow range of diameters and grow with their long fiber axis in parallel orientation to the bundle length. The asbestiform habit imparts to the asbestos minerals sufficient flexibility and tensile strength so that most can be woven into cloth. In the past application has focused on their ability to insulate against the transfer of heat. However, these minerals possess other properties which make them useful in many industrial applications. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Asbestiform; Fibrous

Jan 1, 2007

By B. Cousins

Copper, nickel, zinc and other ?penalty? metals are found with gold together in nature, and have a similar chemical affinity for cyanide used in leaching operations4. As a result, solutions that come from the heap leach pads contain a significant concentration of penalty metals along with the desired gold. In solution, gold and cyanide form the complex Au(CN)2- that is readily adsorbed onto activated carbon. Penalty metals as individual metal ions also load onto activated carbon and, depending on the concentration of cyanide and the pH of the solution, can form various cyanide complexes. Some of these complexes can also load onto carbon while some are significantly inhibited from loading. Copper, for example, can form the dicyanide complex Cu(CN)2-, the tricyanide complex Cu(CN)32-, and the tetracyanide complex Cu(CN)43-. At a low pH and a low concentration of cyanide, the dicyanide complex predominates. At a higher pH and a higher concentration of cyanide, the tetracyanide complex predominates. Without excess cyanide, however, individual copper ions can remain present. Activated carbon is used in gold extraction because it is highly selective for gold and less so for other metals, such as copper3. However, copper has the ability to adsorb (?load?) onto activated carbon and block the adsorption of gold when it is in the dicyanide form and in a high enough concentration. When copper is in the tetracyanide form, copper loading is significantly inhibited, allowing for the maximum gold recovery. In order to ensure the tetracyanide complex is formed, a combination of both available cyanide and elevated pH must be present. In the South Area of Newmont Mining Corporation?s Gold Quarry mine in Carlin, Nevada, copper and nickel loading becomes a problem when certain acid generating zones of the heap are leached. Copper, nickel, zinc and other penalty metals become leachable and the lower pH uses up more of the cyanide and creates carbon loading conditions for the metals. This decreases the carbon?s ability to extract the gold from solution, decreasing the recovery and increasing the concentration of gold in the barren solution that leaves the carbon columns. In this study, operational data from March through to May of 2007 is presented to show how Newmont developed a quick fix to lower pH and elevated metal concentrations that were causing low gold loadings on activated carbon at their South Area Leach (SAL) heap leach operations. Laboratory tested were also conducted to examine the chemical kinetics of metal loading and the individual effects of increased cyanide concentrations. THEORY Copper I ions form four different complexes with cyanide in solution: the monocyanide species CuCN, the dicyanide species Cu(CN)2-, the tricyanide species Cu(CN)32-, and the tetracyanide species Cu(CN)43-. The species are formed from the following reactions: [Cu)(?+-+ K1 (1) Cu ß2 (2) --+?+23)(3CNCuCNCu ß3 (3) --+?+34)(4CNCuCNCu ß4 (4) ] where K1 equals 1019.50, ß2 equals 1024.03, ß3 equals 1028.65, and ß4 equals 1030.35. Along with these complexing reactions, hydrogen cyanide and water also dissociate in solution, as per the following reactions: [H?+-+ KH (5) OHOHH2?+-+ KW (6)] where KH has a value of 109.24 and KW has a 1014 value2. These six chemical equations compete with each other, with domination of one over the others dependent on the CN- and H+ concentrations. Each complex also has different properties when it comes to its loading behavior on activated carbon. The dicyanide copper complex and the monocyanide copper complex have an affinity for adsorption onto activated carbon that is greater than the affinity of gold cyanide for adsorption. They also have a lower solubility in water, which enhances adsorption. The tricyanide copper complex and the tetracyanide copper complex are water soluble and have an affinity for loading adsorption on activated carbon that is less than the affinity of gold cyanide for loading adsorption1. There are three prime reasons for this phenomenon. First, the extra cyanides mask the metal ion more, which blocks the main adsorption characteristic of the complex. Second, the complexes are also larger, making it harder to physically fit into the active sites on the carbon. This helps make the latter two complexes kinetically inhibited from adsorption, freeing carbon active site to load with gold cyanide complexes. Third, it is also important to consider the expressions of the mass and charge balance. These balances describe all the overall concentration of copper and cyanide in solution, as well as marking overall charges of the ions in solution4. This is important because significantly changing the charge from positive/neutral to more negative is another reason for activated carbon to reject adsorbing the higher cyanide complexes. The speciation of copper and other penalty metal cyanide complexes in solution is dependent on the pH. At lower pH values, increased hydrogen ions (H+) can out-compete metals for cyanide ions. Lower free cyanide in the system leads to the lower cyanide species of copper cyanide predominating, with a noticeable concentration of the free metal, monocyanide and dicyanide species of copper cyanide. At higher pH values, hydrogen ions are significantly reduced, reducing the kinetics of HCN formation. More free cyanide remains in the system, allowing for more complexing. With this higher amount of cyanide in the system, the tetracyanide species of copper cyanide predominates, also with a noticeable concentration of the tricyanide species of copper cyanide. Higher copper concentrations, however, require more

Jan 1, 2009

Even though the economy of the United States remains in recession ? or not, depending on which economist you listen to ? muicipalities still need improved transportation, water and wastewater transit systems. And they are willing to spend the necessary funds on those systems, provided they are affordable, environ-mentally friendly and sustainable. From June 20-23, professionals in the tunneling and underground construction industry from around the world gathered in Portland, OR to learn new ways of providing those systems using the latest technology available. The North American Tunneling (NAT) conference attracted 803 attendees and 108 exhibiting suppliers of equipment and services.

Jan 1, 2010

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

By Robert A. Bauer, Paul B. DuMontelle

In 1985, participants of the multi-year Illinois Mine Subsidence Research Program conducted surveys of subsidence effects on crop production from current high-extraction mining methods, selected a site to characterize the profile, strain, fracture development in overburden materials and changes in aquifers produced by subsidence from high-extraction mining, characterized floor materia1 s in three mines, and established bibliographic reference and data base files. The Illinois State Geological Survey, University of Illinois at Urbana-Champaign, Southern Illinois University at Carbondale, Illinois Department of Mines and Minerals and Twin Cities Research Center of the U. S. Bureau of Mines are coordinating State and Federally funded research.

Jan 1, 1986

By Yoginder P. Chugh

Most mines are large producing 0-25 mmt annually. The coal is mine.) at depths ranging from .0-150 m 120-500 ft mining at 300 m .(,1000 ft) depth is anticipated in the future. Single and multiple seams ranging from 3-12 m 10-40 ft) in thickness are mined. Most overburden is unconsolidated and consists of sands, and sandy or silty clays. The stripping ratio (volume of overburden to volume of coal mined) varies from 3-L. The overburden and coal is mined in benches 8-12 m -(24-40ft) high; the high-wall angle is about 45 degrees. Bucket wheel and bucket chain excavators are commonly utilized for overburden and coal removal, Some of the large overburden stripping machines nave capacities. Ranging from 4400-10,000 bank cu ( 6000-14,000 BC) per hour. The overburden from the upper benches is transported around the pit using the trains and belt conveyors. It is deposited in the spoils using large stacker-conveyor systems capable of handling 2550-7300 cu m/hour (7500-10,000 cu yds/hour). The overburden from the bottom two or three benches is transported across the pit using the conveyor bridges which are computer controlled. Conveyor bridges capable of handling overburden up to 60 m (200 ft) high are currently in use; a 60 a (20e ft) high conveyor bridge has a capacity of 85 x 10 cu ( 118 x 10 cu yd) annually. The coal is loaded in the trains directly and shipped to power plants or coke oven plants.

Jan 1, 1980

By Kimberley MacHardy, Ann Maest, Greg Lawson, James Kuipers

Although water quality predictions are often made in Environmental Impact Statements (EIS's) as part of the National Environmental Policy Act (NEPA), comparisons between predicted and actual water quality conditions are rarely reviewed. A comprehensive review of predicted and actual water quality conditions was conducted for a number of large U.S. hardrock mines with EIS’s. For mines with large differences between predicted and actual conditions, factors responsible for the deviations, such as characterization and modeling errors or engineering failures, were identified. Recommendations are made for how the NEPA process could be modified to better predict water quality at hardrock mine sites.

Jan 1, 2005

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By J. -F. Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

Jan 1, 2011