Search Documents

By J. C. Yingling, G. T. Lineberry

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will he intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder through flow to avoid production bottlenecks. Simulation studies suggest that the control strategy would be very effective in reducing capacity requirements of gathering belts.

Jan 1, 1993

By J. R. Carr

A crucial concern when implementing computer algorithms for geostatistical analyses on microcomputers is speed of execution. Kriging, in particular, typically relies on a Gauss elimination algorithm to solve for weights. Because such an algorithm is required for each estimate, the solution for weights can result in very slow program execution speed on a microcomputer. One approach to enhancing the efficiency of Gauss elimination is demonstrated herein. The upper triangle plus diagonal of the intersample covariance matrix is used in a modified banded Gauss elimination algorithm. Results show that such an algorithm yields approximately a two-fold reduction in execution time for kriging when the number of nearest neighbors used for estimation is large.

Jan 1, 1990

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By Jorge Lanza

SUMMARY La Granja copper deposit, in terms of volume, is among the five largest deposits in the world and represents reserves of three thousand million tones. The field consists of a 40 m. thick layer of copper lying over the secondary ore and further down the primary copper. The flotation process has indicated a recovery rate of 88 to 90 percent and concentrates of 27 to 32 percent of copper. The acid leaching process of low grade ore produces financially acceptable results. To carry out the project, it is necessary to build long distance pipelines and a port. Both the Feasibility Study and the Environmental Impact Study on the project have been approved by the Peruvian government. INTRODUCTION La Granja is located in the district of Querecoto, province of Chota, in the department of Cajamarca, in the Northwest of the country (Figure 1). Geographically it is situated on the eastern slopes of the Andean mountains at an altitude of 2,000 to 2,700 m.a.s.1. (Figure 1). The site is an 8 hour car ride from the city of Chiclayo, capital of the department. The first 60 km. are over a paved road and the remaining distance is over a narrow hard dirt road. The copper porphyry of La Granja was discovered between 1969 to 1971 during some geochemical prospecting activities carried out by the State mining institution, Ingeomin (currently Ingemmet). From 1978 to 1982, Ingemmet continued with its geochemical and geophysical studies supported by a German technical assistance program. A total of 19 bore- holes were drilled (5,814 m.) and a 90 m. long tunnel made. This study calculated reserves of 175 million MT. In 1993, Minero Peru drew up a technical-financial study based on the above studies and proposed a 12 year extraction operating program: 20,000 MT daily using the leaching process, followed by 13 years of operation using the flotation process with the same daily volumes. In 1994, Cambior Inc. won an international auction in order to carry on further exploration work and to have a purchasing option. Since that date the company

Jan 1, 1998

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By F. Villanueva Araya

Compania Minera Disputada de las Condes (CMD), an Exxon Affiliate stewarded by Exxon Coal and Minerals Company, operates two' copper mines and concentrators in Chile. Pilot plant studies were initiated in 1984 using a 0.46 meter and a 0.91 meter diameter column for the cleaning of copper concentrate. This eventually resulted in the design and operation of a rectangular column with an area of 6.8 m2, increasing the final copper concentrate grade from about 30% to almost 32'1. Cu without any loss in copper recovery. Evaluation studies of a commercial bubble generator as against the previously used filter cloth air sparger are now in progress.

Jan 1, 1990

By Daniel Maine

Swelling clay soils have been problematic to many types of infrastructure in the United States. However, their impact on underground construction is often misunderstood. The use of swell pressures in design of initial tunnel and shaft support lacks proper guidance and is often mis-interpreted. This paper provides insight and guidance on how to implement a geotechnical investigation program to determine if swelling soil exists at a site and how it impacts the design of temporary support systems for underground projects. An example is provided for how swell pressures were incorporated into the design of an initial support system for a rib and lagging tunnel system and problems that occurred.

Jun 23, 2024

By Harry Verakis

Electronic detonator systems are an advance in technology beyond conventional electric detonators for initiating explosives and blasting agents. Their use is widening into the mining operations of the U.S.A. Each electronic detonator system differs in design, construction, operation, and testing features and each system is different than “conventional” electric detonators. There are benefits of electronic detonator systems which serve to improve blasting safety. With the introduction of electronic detonator systems for mine blasting, issues were raised about the application of MSHA regulations for shunting and circuit testing. The MSHA regulations for surface and underground mine blasting operations address the use of “electric” detonators. Although electronic detonators are initiated by an electric pulse or current, their design is unlike “electric” detonators. To resolve the issues of shunting and circuit testing with respect to MSHA regulations, a technical and field evaluation of electronic detonators was made and the results are presented.

Jan 1, 2005

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By K. F. Unrug

The research work reported in in this paper deals with the monitoring of roof behavior in a drift mine located in Eastern Kentucky operating in the Coalburg Seam. The thickness of the seam at the monitoring site ranges between 9 and 10 feet with the immediate roof changing from sandstone to shale then back to sandstone. Shale thickness varies between 0 and 2.5 feet. The characteristics of the immediate shaly roof were monitored with 38 dynamometers which were set up in three survey lines to cover the entire range of shale distribution. The dynamometers are capable of providing accurate load readings in the range of +/- 5 pounds. To closely observe the contribution of moisture toward roof deterioration the dynamometers were set up in intake and neutral airways. A television borescoping camera was used in conjunction with the dynamo- metric instrumentations at pre- determined observation holes to physically observe and record the separation process of the shale and sandstone stratum with respect to time. Monitoring took place between January 1985 through January 1986 in order to cover a full cycle of dry and wet mine conditions associated with the seasonal changes. Analysis of the data show a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1986

By J. James Eidel

Geological interpretations generally require projections from direct observations at the earth's surface. Crustal projections include mineral deposits as well as the geochemistry of the crust and its fluids, structure and tectonics. Drilling offers opportunities for verification of the required projections, and is thus a required step in furthering crustal understanding. Like any new science, the direct observations that drilling provides commonly generate major surprises and stimulate totally new ideas. Drilling is costly. There are many critically important scientific problems with societal and potential economic benefits in mineral deposits which have not been drilled because the holes are difficult to justify as economically sound risks for private capital. Such holes, however, are highly justifiable research goals for government because of the significant new opportunity for ore deposit insight and exploration that they afford. The earth science community is prepared with excellent drilling projects for research in mineral deposits.

Jan 1, 1985

By L. P. James, W. W. Atkinson

Utah has produced about 31.7 kt (1 billion oz) of silver, more than any state in the United States except Idaho. Several high-grade ore systems in Utah, where the mines are now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham openpit mine has also yielded more byproduct silver than other porphyry copper-molybdenum-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcaniclastic rocks. Thick permeable latest-Proterozoic basement metaquartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d'Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to Tertiary porphyritic plutonic rocks.

Jan 1, 2003

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977

By William J. Attwooll

The development of gold heap leach projects in the Cripple Creek, Colorado, mining district has required utilization of heap leach pad sites other than relatively level natural ground. This paper describes the construction of a heap leach pad adequate to accommodate 907,000 tonnes (1,000,000 st) of ore over the surface of a tailings pond constructed during previous milling activities at the site. Based on the design parameters and the observed behavior to date, it has been found feasible to construct a major heap leach pile on the surface of a conventional tailings pond.

Jan 1, 1987

By Nik Sokol, Mike Jaeger, Leo C. Weiman-Benitez

Silicon Valley Clean Water signed a progressive-design-build (PDB) contract with Barnard Bessac Joint Venture (BBJV) to design and construct the Gravity Pipeline tunnel in Redwood City, CA. Owner and Design-Builder teamed with designer Arup to provide a final product: 3.3 miles of 182 in. O.D. precast concrete segmentally lined tunnel with 10 ft. and 11 ft. I.D. Fiberglass Reinforced Polymer Mortar (FRPM) carrier pipe, complete with two FRPM Drop Structures. BBJV and Arup collaborated with SVCW to evaluate alternative design concepts, negotiate an agreeable price and reduce contingencies through a transparent estimating process, and deliver the project ahead of schedule.

Jun 13, 2023

By James N. Brentz

This paper deals briefly with the problem of efficiently selecting the most cost effective haulage truck. Problems and factors are identified that effect productivity and operating cost. Despite the sophistication of computerized vehicle simulation programs, there is a wide disparity in accuracy and methodology, particularly in dealing with the various elements of cost.

Jan 1, 1984

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015