Search Documents

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

"Outotec’s TankCell® e500 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland. The TankCell® e500 is the first cell in this size class (500m3) to be run in an operational duty and it has been working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50. In addition the cell has proved to be very energy efficient, operating with a specific energy of around 0.4kW/m3 under production conditions. This presentation will provide a review of the installation and operation of the TankCell® e500 at Kevitsa and will summarize the results found in the published literature from the various testing campaigns conducted around the cell. INTRODUCTION The TankCell e500 was installed and commissioned at the Kevitsa mine in northern Finland in 2014. Post startup the cell was initially run for testing and optimization with various test campaigns undertaken. but was subsequently taken into a production duty (Mattson et al., 2015a). At Kevitsa the cell is run as the first copper rougher replacing the previous two copper roughers (both 160m3) in this duty. The unit is running at between 38-40% solids at a feed rate of approximately 850tph. Since operational the average copper recovery from this single cell has been around 71% copper. This is typically with an enrichment ratio of around 50 being fed with an average head grade of 0.3% copper. More details on the circuit configuration and production performance of the e500 at Kevitsa can be found in Mattson et al., (2015a) and Murphy et al., (2016). In addition through the optimization program with the use of a variable speed drive controlling rotor speed it was found the the e500 was very energy efficient under production conditions. During this work the cell was found to run at a specific energy of around 0.4kW/m3 which exceeded design expectations (Xia et al., 2015)."

Jan 1, 2016

By Viacheslav Lyakhov, Cornelis H. Iestra, Victor I. Beloborodov, Vitaliy Bogdanovich

The results of a study and effective use of flotation for processing of ores with complex mineral composition containing fine-disseminated minerals with high specific density are presented in the paper. The object of research was complex baddeleyite-containing ore from Kovdor deposit (The Kola peninsula, Russia). Baddeleyite is a valuable, rare mineral, natural Zirconium dioxide with 5.8 - 6.0g / cm density, grade content 0.15 - 0.17 and dissemination less than 0.2 mm. The authors carried out a thorough investigation of baddeleyite- containing products selected in different sites of gravity flowsheet. It was determined that due to similar specific weight some sulphide minerals (pyrite, pyrrhotite) come into concentrate together with baddeleyite and, also, minerals of pyrochlores group (hatchettolite). The results obtained revealed the possibility of use the flotation for retreating rough baddeleyite concentrate. he given gravity concentrate has a number of specific features, e. g. high density of its minerals which, in its turn, provides for high speed of sedimentation of solid phase in pulp, and for the presence of large amount of sulphide minerals (up to 10%) having good flotability. With these features being taken into account a technology for flotation of baddeleyite-containing products after their preliminary gravity concentration has been developed (up to 5 - 10% Zirconium dioxide). The technology has three flotation stages. At the first one the reverse flotation of baddeleyite is carried out during which "light" minerals (forsterite. apatite and carbonites) come into froth product and at the second one flotation of sulphide minerals and at the third one direct flotation of baddeleyite is performed from the underflow product. The following reagents were used for flotation: of phosphate type (sodium tripolyphosphate, mono and diethers of alkylphosphpric acid) and sodium xanthate as collector for sulphides. The given set reagents provides for high effectiveness of flotation due to selective of collectors and presence of froth layer with high carrying ability. New flotation technology of recovering of baddeleyite from complex ore was developed and applied at the Kovdor Mining Plant, using AKER flotation machines.

Jan 1, 1995

By James J. Scott

In the fall of 1976 the author started test work with Friction Rock Stabilizers in uranium mines of the West, principally in the Ambrosia Lake and Churchrock districts of New Mexico. Tests were also conducted in other uranium mines in the Rocky Mountains area. These mines are plagues with problems in ground control due to the weak formations in which mineralization occurs, mudstones, siltstones, weak sand, etc. For this reason, it is extremely difficult to obtain good anchorage for long periods of time with conventional mechanical roof bolts. Resin bolts give good anchorage but are expensive and, because of hole erosion and difficulties in installation due to inadequate equipment for mixing the resin and placing the rebar, they are not widely used. Field testing was also carried out in trona, limestones and hard and soft shale formations. The mechanism of the Friction Rock Stabi1izer support is discussed and pull test data presented for various rock types.

Jan 1, 1977

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By W. M. Snoddy

The Montana Tunnels diatreme is a low-grade polymetallic ore body containing economically mineable quantities of gold, silver, lead, and zinc. Widely varying gold grades combined with the general erratic nature of the mineralization create a complex sampling, assaying, and ore control problem. In order to maximize productivity and profitability, a variety of procedures have been used. These include differing sample size, frequency and method. In addition, assay techniques have been adjusted and refined to fit specific requirements, the result of which is an accurate, functional sampling and ore control system.

Jan 1, 1991

By Melvin W. Kraschnewski

In 1966 Central Ohio Coal Company and Bucyrus-Erie signed a contract authorizing Bucyrus-Erie Company to design and build a 220 cubic yard dragline. This dragline would be used for stripping overburden from their coal reserves located near Cumberland, Ohio. The size of the machine was arrived at after a thorough application study of their annual coal output requirement, depth of overburden and type of terrain. The design and construction of this machine which has been designated by BECO as model number 4250-W is the title of this paper. Size wise based on machine weight the 4250-W represents an increase factor of three over our largest current dragline. Probably the easiest way of presenting a machine of this size is to build it from the bottom up.

Jan 1, 1969

By Roy M. Fleming

During the decade of the 1970's, a new emphasis was placed on assuring a safe and healthful workplace for all American workers. Much of the basis for this national effort was federal legislation: the Occupational Safety and Health Act of 1970 and the Federal Mine Safety and Health Act of 1977 (amended from the 1969 Coal Mine Act). One of the agencies involved in this protection effort is the National Institute for Occupational Safety and Health (NIOSH) of the Centers for Disease Control (CDC) in the Department of Health and Human Services (DHHS). In fulfilling its mandates under the 1970 and 1977 Acts, NIOSH conducts research, experiments, and demonstrations to support and stimulate advancements in health and safety practices. Priorities for NIOSH research are established primarily through congressional mandates, requests from the Department of Labor, needs as defined by NIOSH researchers, and surveillance information. Emphasis is placed on research in the areas of toxicology, industrial hygiene, physical and chemical sciences, physiology, ergonomics, engineering, psychology (behavior and motivation), and epidemiology (industry-wide studies). The framework of the current Institute program to identify, evaluate, and control occupational hazards includes activities in surveillance, research, evaluation, and training. These activities are planned and evaluated through a system that coordinates the efforts of eight research and scientific divisions. Each division develops projects to address program areas that have been identified by NIOSH management as having highest priority. In surveillance programs, the objectives are to identify substances and agents found in a representative sample of workplaces and to collect and evaluate information on rates of disease and injury in occupational groups. Information is also collected on occupational safety and health programs implemented by industry. Estimates of worker exposures and the potential for adverse health effects are considered in setting priorities for further investigations. A related activity, which also serves to provide technical assistance to industry, is NIOSH's Health Hazard Evaluation program. On-site investigations of workplaces are made in response to worker, employer, or government agency requests. Both industrial hygiene and medical examinations are conducted, and the results contribute to identifying new problems and evaluating their significance which may have public health implications beyond the particular worksites that are investigated. Field and laboratory research projects are performed to meet several objectives: - Characterize the working environment by evaluating current and past exposure levels for workers who are included in epidemiological or medical investigations. - Develop epidemiological information to define the association between the substance or agent under investigation and the acute and chronic health effects on workers. - Determine through animal studies the parameters of an association between exposure and effect. - Investigate the etiology of disease. - Develop sampling and analytical instruments and techniques and demonstrate their application for measuring toxic materials in the workplace. - Formulate sampling strategies that will accurately and precisely indicate exposure levels. - Develop medical procedures to prevent disease and to detect the presence of disease and early indicators of disease. - Assess the technology for control of exposures, including engineering and administrative techniques, personal protective equipment, and work practices. Presently, the research program is focused on reproductive effects, neurotoxic effects, injury/trauma, lung disorders, cutaneous disorders, cardiovascular disorders, cancer, stress-related disorders, effects of physical agents, digestive disorders, and renal and other organic disorders. In studying these issues, priorities are determined by the seriousness of possible adverse health effects resulting from occupational exposures, the feasibility of studying existing records or obtaining new data, and the size of the population which is potentially affected. Where there is low level of suspicion concerning adverse health effects or where an occupational disease occurs in a variety of industrial environments, investigations are limited to gross analyses of health effects such as review of mortality patterns. In such studies, the industrial populations selected are those for which existing data resources can be utilized. Such data consists of records of occupational exposures or health status which have been maintained by the employer, the union, or Government agencies. Where a review of the available information suggests that serious health hazards exist and the existing data resources are inadequate for quantifying the relationship between the specific biological response and type and degree of exposure, prospective studies are initiated. Information derived from such research is essential for the development of sound criteria for control of industrial exposures to noxious agents. Other input to the criteria documentation process comes from searching and evaluating the literature. Criteria documents contain the recommendation of an environmental limit where information is available to support it, as well as the recommendation of work practice controls, medical evaluation, information for workers to recognize and avoid the hazard, and identification of specific research gaps. In some cases, during the criteria document preparation, gaps in knowledge are found which necessitate further research before an occupational standard can be recommended.

Jan 1, 1981

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By D. N. Thompson, R. L. Sayer, K. S. Noah

Economical remediation of acid rock drainage (ARD) at secluded high-altitude western ore mines is difficult given the current treatment technology. Several passive-engineered systems that are based on wetland technology were tested in the laboratory with three western ore mine ARDs (Co, Cu and Fe mines) and with a copper leachate effluent. These systems used well-weathered lodgepole pine sawdust as the sole carbon source and mud from a pond at one of the mine sites as the source of sulfate-reducing bacteria (SRB). Simple one-pass flow-through systems removed 44% to 99% of the vari¬ous heavy metals front the Co and Cu mine ARDs and increased the pH from 3 to 7 after 28 days of SRB acclimation with a five-day residence time. Carbohydrate utilization rates were generally low, except for one 437-day run, which consumed 25%, 30% and 21 % of the cellulose, hemicellulose and lignin, respectively. Initial pH, amounts of toxic heavy metals and the degree of predegradation of the sawdust were found to significantly affect both remediation potential and acclimation time. Engineered SRB systems, alone or in combination with other passive technologies, offer promise for the economical remediation of western US ore mine ARDs.

Jan 1, 2000

By J. Z. Keating

There are close to two million tons of Industrial Minerals processed and sold in North America wherein the processor/marketer has no affiliation with the source mine. The largest quantity, about 800,000 tons, is barium sulfate, which is sourced in lump ore form mainly from China and India. The Alumina Trihydrate Industry sources several hundred thousand tons from various alumina refineries. Substantial quantities of bauxite, zircon, magnesite, and fluorspar arrive in North American ports each month. There are also rapidly growing quantities of offshore talcs and calcium carbonate ores being processed in U.S. plants. These feedstocks are usually quite pure, have unique properties, and enjoy bulk rail or waterborne freight economies that allow successful competition with locally sourced raw materials. With increasing restrictions on mining activities, and the increasing need for sophisticated functional minerals, the importation of minerals will continue to grow.

Jan 1, 1994

By J. G. Groppo

Froth flotation has been shown to be an effective method for reducing Loss-on-Ignition (LOI) of ponded or landfilled fly ash. Reduction of LOI is required for many fly ashes, particularly those produced from low-No, burners, in order to meet ASTM requirements for use as a mineral admixture in Portland cement concrete. An additional ASTM requirement, fineness, is critical in determining end use applicability, and in many cases, classification of fly ash is necessary to produce an acceptable product. Hydraulic classification has been shown to be a simple, cost-effective method for classification of a variety of minerals including silica, phosphate, mica, coal, etc. and has shown to be similarly effective on fly ash. The combination of froth flotation and hydraulic classification facilitate the production of a high quality pozzolan that meets or exceeds ASTM specifications. This combination has been rigorously evaluated and results of pilot-scale testing are presented. Pilot scale testing was conducted on fly ash from two active utility storage ponds and demonstrated that high quality, consistent pozzolan could be produced using APT's Fast Float? Technology. Along with the pozzolan, additional production of aggregate for masonry mortar and a low sulfur, medium Btu fuel were also demonstrated. The Fast Float? process incorporates several simple unit processes to ensure pozzolan consistency; classification controls particle size distribution which is critical to achieving early strength, flotation controls the grade with respect to L.O.I. (Loss on Ignition) while dewatering controls the moisture content.

Jan 1, 1998

By Bill Morgan

This paper discusses the economic zones of application for several different types of earthmoving equipment: dozers, wheel loaders in load-and-carry applications, wheel tractor scrapers, articulated trucks, rigid-frame trucks and wagons. Only the medium to large pieces of equipment were considered. From this chart (Figure 1), you can see the size range, in tons of carrying capacity, of Caterpillar equipment and the specific models analyzed.

Jan 1, 1994

By George M. Leonard

Mineral commodities on National Forest System lands contribute to the nation's well being. Access to these commodities is dependent on public perceptions of the effects of mineral operations on other resources. An outlook is described which the Forest Service believes is essential to the minerals industry if it plans to continue seeking minerals on National Forest and Grasslands.

Jan 1, 1991

By T. V. Subrahmanyam

Unlike coarse particles (40-50 µm), the fines (<10 µm) have low collision efficiencies with gas bubbles in flotation process. Among the alternative methods for recovering the fines are their aggregation with coarse particles (carrier flotation) and flocculation of the fines alone (shear-flocculation), prior to flotation. In any case, hydrophobic aggregation is the mechanism involved though the technique is known by different names in literature. This paper deals with theory and state-of-the-art of particle aggregation. To illustrate the dependence of aggregation on particle hydrophobicity, charge and, in turn, the sheer force, the results of quartz-DDACI and galena-xanthate systems are considered. In the flotation of complex ores selectivity is achieved by chemical control and aggregation of particles of the same species is analogous to that; however, more work is necessary on ores for a better understanding of the pulp chemical aspects from the view point of selectivity in aggregation. For a few ores, the results of earlier workers confirm improved recoveries of fines by aggregation prior to flotation.

Jan 1, 1997

By K. N. Santini

The evaporite deposit at Searles Lake consists of alternating brine-saturated saline beds and saline-bearing mud beds. Three major subsurface brine-saturated saline horizons have been identified by private companies and the U.S. Geological Survey. They have been termed, from bottom to top, the Mixed Layer, Lower Salt, and Upper Salt. The important water-soluble components (Na, K, Mg, CO3, HCO3 , SO4, Cl, and B407) are either in brines or have combined to form the following minerals: halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, northupite, sulfohalite, glaserite, etc. Kerr-McGee Chemical Corp., the current operator at the lake, selectively pumps interstitial brines from each of the major horizons to feed its three chemical plants. As the pumping continues, brines are continuously replenished within the deposit by dissolution of the minerals through natural recharge or artificial fluid injection (solution mining). The brines are processed to produce a variety of chemical products, which include sodium carbonate and sulfate, potassium chloride and sulfate, sodium borate, and boric acid. The Anaconda Minerals Co. has been evalua¬ting potential domestic trona acquisition since 1981. We have evaluated various properties in the Green River, Wyoming trona district, and Owens Lake and Searles Lake in southern California. In 1983, we purchased with our joint-venture partner, Leslie Salt Co., the southern portion of Searles Lake from Occidental Petroleum Corp. Since mid-1983, Anaconda has been conduct¬ing a small exploration-drilling program at the property. The initial core holes were drilled along and adjacent to the existing access road. In 1984 we used an all-terrain drill rig to gain access to drill sites on the playa where no roads exist. The use of this equipment proved to be highly successful. The drill program consists of coring to an average depth of 450 feet and collecting brine samples from potentially commercial horizons. The brine samples are collected by setting a packer and swabbing the hole. The core is logged and split lengthwise; one-half is submitted to our Tucson Geoanalytical Laboratory for semi-quantitative mineralogy by X-ray diffraction and the following suite of chemical analyses: Na, K, Mg, C03, HCO3, SO4, Cl, B407, Li, H20 insolubles, and acid insolubles. Additional test work for selected core samples will include effective porosity and horizontal permeability determinations. The brine samples are subjected to the same suite of chemical analyses (minus insolubles) as the core samples. In addition, specific gravity is also determined. Both cross sections and isopach maps are being constructed. The hydrological characteristics of the potentially commercial horizons are also being investigated.

Jan 1, 1987

By J. F. T. Agapito

Significant increases in extraction ratio on the order of six to eight percent, equivalent to as much as 142 t/m of panel advance, have occurred at the Big Island Mine during the last five years with the help of a practical rock mechanics program. This increase in resource recovery also has contributed to improvements in productivity. Both conventional and continuous machine mining have been used to mine two flat-laying trona beds at depths of 250 to 260 m in the Green River Formation in south-western Wyoming.

Jan 1, 1988

By T. A. Laser

"INTRODUCTION A positive workplace environmental, health, and safety (EHS) culture affords organizations and corporations many benefits, including increased trust and employee morale, sustainable EHS performance improvements, and reliable productivity and profit margin growth. Unfortunately, many leaders and EHS professionals struggle daily to achieve and maintain positive workplace cultures and consistent business results. While lack of management support, corporate or employee buy-in, resources, and time are common factors that conflict with an EHS culture and safe work behaviors and processes, there are many other actions that threaten the positive attributes of an organization’s culture. Often these culture killers are not recognized, or worse yet, ignored because they are considered taboo. For example, voicing observations or questioning long-held management practices or process that were initially designed to promote EHS values, but no longer do so. Unfortunately, this could be viewed as challenging authority, not being a team player or even not valuing EHS. And for those that speak up, the potential for negative consequences can be real impediments to positive change. Having an open mind, constantly striving to identify culture killers, and putting forth the effort to eliminate them are the first steps to begin reaping the benefits of having a sound workplace culture. This paper helps readers to: • Recognize culture killers that negatively impact fostering and maintaining sustainable EHS cultures in the workplace. • Understand how to prevent, avoid, and respond to culture killers, before they wreak havoc in your organization. • Assess EHS culture strength, and implement plans to continuously improve it. The desire to draw boundaries around concepts, put things into boxes, and nail down requirements for something that is virtually impossible to solidify for any length of time is quite fascinating! These desires can pose challenges when trying to define what the perfect EHS culture should look like. The very act of trying to define our culture tends to create silos, and these silos, in turn, can become “culture killers”. The following is one of the most common culture killers. UNBALANCED ORGANIZATIONS TRIGGER CULTURE KILLERS Unbalanced organizations occur when an organization’s constantly shifting focus forces other important needs to take a back seat--until the focus changes again. This balancing act can be detrimental and lead to catastrophic results including low morale, lack of trust, employee dissatisfaction, high turnover, increased incidents, poor profit margins, loss of market share, and ultimately into organization-wide failure."

Jan 1, 2018

By R. D. Lord

This paper deals with the search for the best practical means of storing sulphide bearing tailings, where there is no residual excess of carbonate material. It is the common experience that the sulphide content decomposes, with the aid of bacterial action, and the resulting sulphuric acid escapes, along with any heavy metal solutes, through embankments that are usually porous to some degree. The problem is typified in the tailings of the uranium operations of Elliot Lake, Ontario, where mining started some 20 years ago. The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base metal ores. Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice. Now experience has shown that these areas, some idle for over a dozen years, release acids, in seepage and overflows, to an unacceptable degree. To protect natural water courses neutralizing plants are operated wherever required. Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8.5 and precipitate heavy metals that may be in solution. The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found.

Jan 1, 1975

By C. S. Vender

Knife River Coal Mining Company&apos;s Beulah Mine is a multiple seam lignite operation located in western North Dakota. The mine began production in 1963 with annual production at 450,000 metric ton and now produces 2.2 mm ton. As development progresses, operations have advanced into more complex geologic areas. Various techniques have been analyzed to maximize coal recovery in a cost effective manner. Additional studies are on-going to determine what changes will be implemented as we encounter deep wet sands in the reserve area.

Jan 1, 1991