Search Documents

By D. F. Scott

The purpose of this study was to determine if miners are at risk from exposures to chemicals used in the mining industry, and determine the nature and sources of the illnesses and injuries. The authors reviewed the Mine Safety and Health Administration?s (MSHA) Employment and Accident, Injury, and Illness database and identified 2,705 cases of chemical-related injuries and illnesses that were reported to MSHA from 1999-2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker. The number of nonfatal days lost did not change significantly and overall, the incidence rate of chemical-related cases decreased by 36%. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods, and safety culture to insure that their workers are protected.

Jan 1, 2009

By James C. Hower, B. K. Parekh

Introduction The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; and (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Although boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist; density differences; the relative friability of the coal and its associated impurities; hardness; and strength. Some of the other factors related to preparation are petrographic composition and rank. RANK CLASSIFICATION Coal is a general designation for a great number of solid organic minerals with different compositions and properties; all are rather rich in carbon and have a dark color, generally black. Next to mineral oil and kerogen, coal is the most important reservoir of carbon in the world. Carbon is an indispensable necessity of life as well as the main source of energy. Coals are found in stratified deposits, sometimes at great depths. All coals owe their origins to slow decomposition and chemical conversion of immense masses of organic material. As found in seams, coal is a heterogeneous mixture of organic and inorganic materials. Not only are there large differences in the properties of coal originating from different seams, but also in coal removed from different locations in a single seam. A genetic relationship exists between peats, brown coals, lignites, biturninous coals, and anthracites. As a whole, the process of coal formation, or coalification, proceeds as a continuous transformation of plant material, each phase characterized by a degree of coalification, or rank. As a measure of this rank, the carbon content or some related parameter can be used.

Jan 1, 1991

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By R. Raitani

Five kaolin crudes from the state of Georgia in the U.S. were investigated for processability with chemically enhanced magnetic separation (CEMS) technologies developed by Cytec. The technologies used magnetic reagent alone or in conjunction with specialty chemicals to selectively agglomerate and magnetize the desired minerals (impurities) to be removed by the conventional magnetic separation equipment. All crudes indicated treatability using CEMS. Results indicated that CEMS technology could be applied to different kaolin crudes to obtain a product with titanium impurities less than 0.6% TiO2 from individual crudes. The features and benefits of the technologies were also reviewed.

Feb 1, 2012

By Guy R. B. Elliott

If chemical mining is to work, it is extremely important to watch heat balances. Some reactions with coal give off heat and others absorb heat. The reactions of coal with oxygen or air give off heat, but the reactions of coal with steam or with carbon dioxide absorb heat. By balancing the proportions of the two types of reactions, the energy of the coal can be almost completely recovered and environmental damage is minimized. The chemical reactions are listed in Table 1 in the usual form with subscripts (s) and (g) indicating solid or gaseous materials. In reaction 1, solid corbon, C(s), reacts with gaseous oxygen, O2(g), to produce gaseous carbon dioxide, CO2 (g). H means enthalpy or available heat in the material; F is free energy, and it measures whether the reaction can go at all, and if so, how much.

Jan 9, 1973

By M N. Ingham

X-ray fluorescence (XRF) spectrometry has always been considered to be a comparative method of analysis. Reference materials are required to calibrate the analytical system. This paper describes the use of a set of æsyntheticÆ oxide standards, made from commercially available high purity compounds, to calibrate a spectrometer for 21 major and minor oxides. The spectrometer software uses simple methods of background correction, and a fundamental parameter method of matrix correction. Sample preparation is by fusion in 66 per cent lithium tetraborate, 34 per cent lithium metaborate. The use of synthetic standards, made from traceable compounds, brings XRF significantly closer to being a primary rather than a comparative method. Reference materials were used to validate the method described and examples of accuracy for major constituents are given using ores and other minerals. This method has successfully been used to analyse a wide variety of minerals and ores, as validation data shows. A titanium process example clearly shows the benefits of highest accuracy analysis.

Jan 1, 2008

By H. Yasuhara, N. Kinoshita, S. Nakashima, K. Kishida

"In this study, flow-through experiments in fractured rocks have been conducted under different stress, temperature, and pH conditions so as to understand the evolution of permeability induced by these conditions. Throughout the experiments, the confining pressures and temperatures are well-controlled. Effluent concentrations are also measured for the ten elements of Si, Al, K, Fe, Ca, Na, Mg, Ti, S, and Cl that are included mainly in the targeted rocks. In the early stage of the experiments, the fracture permeability measured abruptly decreases with time, and subsequently reaches quasi-steady state within a relatively short period. In contrast, the permeability in the intact rocks monotonically increases with time. The permeability increase and decrease are attributed likely to the relative dominance of mineral dissolution in the pore spaces and to that of mineral dissolution/crushing at the propping asperities within the fracture and/or mineral precipitation onto the free surfaces, respectively. The evolving rates and magnitudes of the permeability are likely to be controlled by the stress exerted over the contacting asperities, temperatures, and pH of the permeant. Thus, this complicated behavior should be attributed to the coupled chemically- and mechanically-induced effects, which should be examined in more detail for longer period to contribute to the safe entombment of radioactive wastes. INTRODUCTIONUnderstanding of the flow and transport characteristics of porous/fractured rocks is required for the safe and long-term geological isolation of energy-related by-products (i.e., high level radioactive wastes and anthropogenic CO2). Notably, under relatively high temperature and stress conditions, mechanically- and chemically-mediated processes may alter the pore structures in rocks, resulting in an irreversible evolution of the flow and transport behavior. Augmentation in permeability may result from mechanical dilation due to shearing and mineral dissolution within the pore spaces, while reduction may result from reversible or irreversible mechanical compaction, mineral dissolution at the contacting areas, and clogging of pore spaces by precipitation of secondary minerals."

Jan 1, 2015

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium, and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. [Table 1] affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak- type brines, produced mainly for lithium. MARKET ATTRIBUTES Some of the important market traits common to industrial minerals used by the chemical industry are: 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities. 8. Purchases are generally by contract of one year or longer term, with spot buying playing only a minor role. 9. Contract prices are usually fixed in short term commitments, but may vary according to assay, with premiums and penalties for content above or below the norm; however, general practice is for specifications to be fixed in the contract with minimums being set for the desired material and maximums for undesired elements. In longer term contracts, prices are often escalated on labor, fuel, and other vendor processing costs. 10. Suppliers of individual commodities to the chemical industry tend to be limited in number and are generally medium- to large-size producers that supply a few major consumers. 11. The bulk of the mineral volume is for basic chemical uses, sulfur suppliers to sulfuric acid producers and fluorspar for hydrofluoric acid producers being typical examples. These basic chemical products then are used for the production of other products. 12. Shortage of a supply of adequate quality leads consumers to seek substitutes. In the case of fluorspar, much work is being done on recovery of fluorine from phosphate rock. Success in the form of fluorosilicic acid and/or hydrofluoric acid production could, in time, affect the hydrofluoric acid chemical industry. 13. Markets tend to be characterized by cycles of shortage followed by oversupply, with attendant wide price fluctuations. 14. Baniers to trade can have an adverse effect on the necessary movement of industrial minerals used by the chemical industry in international trade. Antidumping laws, quotas, and tariffs can disrupt or dislocate normal markets. 15. Chemical industry consumers may back-integrate for security of supply or for favorable economics, sometimes by joint ownership and often with experienced mining partners.

Jan 1, 1994

By Watt KL

Chemical anchors for use in rock bolting have been produced in Australia under licence for several years. These anchors are alternatives to the more normally used mechanical anchors and give improved anchorage strengths under some conditions, although at greater cost. Considerable development during this time has resulted in an improved sausage-type chemical anchor more competitive in price, to such an extent that its use is increasing markedly. Particular-improvements allow load application up to the strength of the bolt within 2 min, reduction in cost, self-extinguishing features in the resin, improvements in manufacturing techniques, and an improved water- insensitive casing. At the same time, smaller bolt sizes have allowed reduction in resin volumes with consequent cost reduction. At this stage several aspects remain to be improved, particularly specialty anchors for specific purposes and Packaging.

Jan 1, 1971

By E. E. Donath

THE coal hydrogenation process is well known as a means for production of liquid fuels from coal. In this paper, the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid-phase and vapor-phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high-molecular-weight aromatics and of tar acids and tar bases. The relative amounts of heavy and middle oil-boiling above and below 325ºC, for instance-can be influenced by temperature, residence time, and catalyst of the liquid-phase hydrogenation. In vapor-phase hydrogenation, a solid bed catalyst is used to convert the intermediate oil from the liquid-phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring-compound content of the liquid-phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparafhns.3 Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid-phase stage, coal is made into a paste with re- cycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high-pressure converters where the liquefaction of coal, conversion of the high-boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470ºC. The reaction products enter the hot catchpot in which oil vapors of lower boiling point

Jan 1, 1953

By E. E. Donath

THE coal hydrogenation process is well known as a means for the production of liquid fuels -from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aromatics and of tar acids and tar bases. The relative amounts of heavy and middle oil-boiling above and below, e.g., 325°C-can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.1 Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydro¬gen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catch-pot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1952

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth's surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country's primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By N. S. Dalal, N. Leelarasamee, V. Castranova, K. Van Dyke, V. Vallyathan

"INTRODCICTIONSilicosis is the chronic fibrosing disease of the lungs caused by the inhalation of crystalline silica. However, inhalation of crystalline silica, may induce three distinctly different disease patterns; i.e., chrome silicosis, accelerated silicosis, and acute silicosis. These three disease patterns differ in their pathologic characteristics, clinical symptoms, onset of disease, and mortality. Many studies in the past have focused on the elucidation of mechanisms involved in the development of chrome silicosis. We recently reported that freshly fractured silica has surface properties that could make it more reactive with lung tissue than aged silica, and that this unique reactivity of freshly fractured silica may be involved in the pathogenesis of acute silicosis (Dalal et al., 1986; Vallyathan et al., 1988; Shi et II., 1988). Because freshly fractured silica could contain some moieties in an ""excited state,"" due to the breakage of silicon oxygen bonds, we postulated that the de-excitation of these moieties could produce light which could be monitored by a luminescence measurement technique. In addition, if this ""excited state'' of silica could trigger a greater biologic response by phagocytic cells, this activation could be monitored by a chemiluminescence technique in the presence of appropriate enhancers.This investigation describes for the first time the use of luminescence in the study of freshly fractured silica and its properties. Enhanced biologic reactivity of the freshly fractured silica with alveolar macrophages was monitored by the chemiluminescence technique.MATERIALS AND METHODSNative silica was obtained from the dust bank of the GenericRespirable Dust Technology Center, Pennsylvania State University, State College, PA, and ground for 3~ min in an agate ball mill. It was then sieved through a 20 micron mesh filter and used within 1 O min as fresh silica or stored in glass bottles for aging. X-ray energy spectrometry and X-ray powder diffraction studies on representative samples were made to confirm the mineralogic purity. All the silica samples were found to be 99 % pure with minimal detectable conlamination by metal ions."

Jan 1, 1990

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974

By S. I. Sobol

Completeness of cobalt recovery from slag requires decomposition of maggemite and non - ferrous metal desorption with polymerized silicon-acid. Cobalt losses are reduced in leaching tai1s up to 200 g/t of iron.

Jan 1, 1993

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By S. K. Kawatra, S. J. Ripke

Finely disseminated iron ores compose much of today's reserves. After removing the silicate gangue, the resulting fine iron oxide concentrates require pelletization with a binder to enable transportation and reduction. Binders can be used more efficiently if their binding mechanisms can be completely understood. Typically, bentonite clay is needed as a binder to improve the strength of the pellets. Bentonite is an effective binder at a relatively low cost, but costs could be reduced further by replacing bentonite with even lower-cost binders, such as high-carbon Fly-Ash Based Binder (FBB). In this study, it was found that bentonite binds by a physical mechanism, while FBB binds by a chemical mechanism. These mechanisms were determined to be incompatible. Partial replacement of either binder with the other reduced dry magnetite pellet compressive strengths below the industrially acceptable value of 22.2 newtons (5 lbf). Activators and accelerators that activated the fly-ash deactivated the bentonite. The incompatibility of these two binders is explained.

Jan 1, 2000

By S. K. Kawatra, S. J. Ripke

During iron ore pellet production, bentonite clay is used as a binder. Typical pellet plants spend from $3 million to $5 million annually for the clay. If bentonite dosages could be reduced by using it more efficiently, a significant cost savings would result. If the binding mechanisms can be completely understood, procedures can be developed to use bentonite more efficiently. Classical bentonite bonding theory is based on the behavior of bentonite at low percent solids and high mixing shear rates. Under these conditions, bentonite was understood to expand, disperse into platelets, and dry into a bonding "film" or "gel." However, these are not the conditions that exist during pelletization, which is carried out at high percent solids and relatively low shear rates. In this paper SEM imaging was used to identify and explain the bonding mechanisms of bentonite on the surface of magnetite concentrate. It was determined that bentonite would form a fibrous network under the proper conditions and that the formation of these fibers corresponded with an increase in the bonding of particles by the bentonite.

Jan 1, 2000

By S. K. Kawatra, S. J. Ripke

During 1998, 62 million tons of iron ore pellets valued at $1.7 billion were shipped from U.S. mines. These pellets are the primary source for domestic iron and steel production. During pelletization, binders are required to improve the green strength of the pellets. Each year, bentonite binder costs a typical plant from $3 million to $5 million. Reducing the bentonite dosage has the advantages of significant cost savings while producing higher quality, lower silica pellets. The authors have recently identified a new and important bentonite binding mechanism, the fiber theory. During this study, procedures were developed that took advantage of the ability of bentonite to form fibers, and resulted in a dramatic decrease in the necessary bentonite dosage. Acceptable quality pellets were produced with the bentonite dosages reduced in half from 14 lb/lt (0.66%) to 7 lb/lt (0.33%).

Jan 1, 2001

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973