Search Documents

Meeting of June 26, 1914.-The President was authorized to appoint Advisory Committees to co operate with the United States Bureau of Mines. The President announced the appointment of Edward H. Benjamin and W. C. Ralston as additional members of the Committee on Arrangements for the San Francisco meeting, 1915. H. T. Van Ells and Judd Stewart were appointed to represent the Institute on a joint committee of several technical societies to consider the standardization of graphical methods for the presentation of statistics. The President announced the appointment of H. Foster Bain to succeed Edward H. Benjamin, resigned, on the Committee of Management of the International Engineering Congress, 1915. The Secretary was authorized to issue a new circular advertising the sale of back Transactions and to sell back Transactions, bound in cloth, at a price of $35 for 46 volumes, provided sufficient orders were received to warrant the special binding. The sum of $177.50 was contributed to the San Francisco Local Section. Upon recommendation of the Committee on Membership, 70 Members, 4 Associate Members and 7 Junior Members were elected to their respective classes; there was also one change of status from Junior Member to Member.

Jan 8, 1914

By John T. Galey

In all, 210 wellst were completed in southwestern Pennsylvania during 1939, which is 59 more than were drilled during the preceding year. Of this number, 137 were gas wells, which is a considerable increase from the 81 completed during 1938. Only 25 oil wells were completed, as against 28 in the previous year, and 28 dry holes, 6 more than last year. Shallow Development—Gas The increase in the number of gas wells is largely the result of a search for additional gas in Armstrong and Indiana Counties. Although a considerable number of wells were drilled in the latter county, the majority of them produced less than 100 M cu. ft. initial open flow. In Armstrong County, a new pool was opened in Cowanshannock township, producing from the third Bradford sand. Several large wells were obtained there, one of which produced an initial of nearly 12 million cu. ft., with a reservoir pressure of 1100 Ib. However, the productive area has been fairly well outlined by further drilling and shows that the pool covers only about 800 acres. The sand is 20 to 30 ft. thick, and probably has 5 to 6 ft. of pay. Thus this reserve is not an important one. Several wells were found in Menallen township, Fayette County, where the Big Injun sand has been having a play for the past three years, but the activity there is much less than a year ago. Oil On the west side of the Bradford sand gas pool, Cowanshannock township, Armstrong County, a well was drilled which flowed 100 bbl. the first day from the Tiona sand. The probability is that this well is a freak, as the Tiona has been drilled within a fairly close distance on every

Jan 1, 1940

By John T. Galey

In all, 210 wellst were completed in southwestern Pennsylvania during 1939, which is 59 more than were drilled during the preceding year. Of this number, 137 were gas wells, which is a considerable increase from the 81 completed during 1938. Only 25 oil wells were completed, as against 28 in the previous year, and 28 dry holes, 6 more than last year. Shallow Development—Gas The increase in the number of gas wells is largely the result of a search for additional gas in Armstrong and Indiana Counties. Although a considerable number of wells were drilled in the latter county, the majority of them produced less than 100 M cu. ft. initial open flow. In Armstrong County, a new pool was opened in Cowanshannock township, producing from the third Bradford sand. Several large wells were obtained there, one of which produced an initial of nearly 12 million cu. ft., with a reservoir pressure of 1100 Ib. However, the productive area has been fairly well outlined by further drilling and shows that the pool covers only about 800 acres. The sand is 20 to 30 ft. thick, and probably has 5 to 6 ft. of pay. Thus this reserve is not an important one. Several wells were found in Menallen township, Fayette County, where the Big Injun sand has been having a play for the past three years, but the activity there is much less than a year ago. Oil On the west side of the Bradford sand gas pool, Cowanshannock township, Armstrong County, a well was drilled which flowed 100 bbl. the first day from the Tiona sand. The probability is that this well is a freak, as the Tiona has been drilled within a fairly close distance on every

Jan 1, 1940

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgments are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate, and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources. Basic Reasons to Establish a Limestone Quarry Profit Motive: Certainly the dominant and overriding motive must be that of attaining a reasonable profit. In certain situations a quarry firm may acquire land, necessary rezoning (if required), and satisfy all of the other prerequisites preparatory to beginning operations but delaying the actual development.

Jan 1, 1980

By A. C. Dorenfeld

In most mineral enterprises, what is the progress, and shift in responsibilities, as the young engineer advances in the corporation? You are all familiar with the normal pattern-in mine production from level boss, to shift boss, to superintendent to manager; in milling from test engineer, to shift boss, to foreman, to superintendent and then manager; in engineering from surveying on to Chief Engineer; and all then aspire to the corporation presidency. Note the shift-from purely technical jobs, say in the first five to ten years in the profession, to administrative positions for 30 to 40 years. What is the average preparation given to mineral engineering students, who can look forward to about 30 years of administrative work? From the catalogs of 21 institutions, offering 36 curricula of four years length, in mining and/or metallurgy, requiring the equivalent of about 150 to 160 semesterhours for graduation, the following results were obtained: Average number of semester hours of economics, 3 hr. Range of requirements, 0 to 8 hr. Thirteen curricula do not require any economics. Accounting and business law, average: 1 semester hr, 26 curricula do not require business law or accounting.

Jan 2, 1955

By James Aston

THE origin of wrought iron may be taken as coincident with the earliest record of ferrous products. The limitations of primitive methods of manufacture undoubtedly resulted in a material conforming to the general characteristics of what we now classify as wrought iron. Iron has been known from prehistoric times. It is frequently mentioned in Egyptian literature, and some samples in the British Museum are believed to date from 3733 B. C. Iron instruments, tools and weapons were used in Greece in 1400 B. C., and in Assyria and. Italy in 1100 B. C. History records their use in Central and Western Europe in 1000 B. C. And in Styria and Carinthia before the Christian era. The noted Pillar of Delhi is generally assumed to date from 400 A. D. The use of iron was general in Europe in the Roman Empire, and heat treatment of weapons and tools was then practiced. All of this early iron was the result of direct reduction from the ore. It serves to illustrate the ease with which the extraction may be effected, and to point out the well known principle that a malleable product of relatively high purity may be produced from high-grade iron ore at temperatures well below the fusion point of-the metal. The fact is also emphasized that there is no novelty in the seemingly ideal and constantly recurring attempts to effect direct reduction. Economic and engineering considerations have been dominant factors in dictating today's two-step practice in the manufacture of wrought iron and steel. Bear' in mind that all of this history antedated the blast furnace, and a knowledge and use of cast iron. It was only in attempts to get greater output by use of shaft-type furnaces, that cast iron was produced in Germany in the period 1300 to 1400 A. D. This was the result of longer contact with the carbon of the fuel, and higher temperatures in the furnace. This period marked the beginning of the existing two-stage operation, involving as the second step the refining of the. cast iron to a malleable product. For a time this was effected in small hearths not unlike a blacksmith's forge.

Jan 10, 1926

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By J. F. Breedis

The morphology and crystallography of marten -site formed during quenclzing were examined by transmission electron microscopy in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pet Ni and Fe-33 wt pet Ni. Depending upon composition, four types of transformation products were observed in this portion of the Fe-Cr-Ni system. Three of these products are denoted as lath, plate, and surface martensite. The hcp structure found in association with martensite it? certain higlz-clzromium stairzless steels does not influence the transformation crystallogyaphy and cannot he Considered to act as a transitional structure in the transformation from austenite to martensite. DISTINCT changes in the characteristics of mar-tensitic transformations are produced by the partial replacement of nickel by chromium in austenitic iron alloys. Large, discrete martensite plates form in Fe-30 pct Ni, while aggregates of small crystals form in sheets parallel with (111)A austenite planes in stainless steels containing in the vicinity of 18 pct Cr and 8 pct Ni. These transformation structures are termed plate and lath martensite, respectively. In addition, an hcp structure (E) has been observed in certain high-chromium stainless steels in association with martensite. It has been suggested that the E structure acts as an intermediate step in the nucleation of martensitel-' and influences the morphology and crystallography of the final transformation product. However, this structure may be the consequence of the deformation of austenite arising from the shape distortion accompanying the transformation to bcc martensite.' An hcp stacking of atoms is produced in an fcc lattice by the introduction of an intrinsic stacking fault on alternate (111)A planes. At present, the arguments behind each explanation for the E structure are based on circumstantial evidence. This investigation seeks to determine the importance of the hcp structure to the martensitic transformation, and to examine the crystallography and morphology of the structures produced in bulk samples by quenching in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pct Ni and Fe-33 wt pct Ni. These aspects of the martensitic transformations occurring in these alloys have been studied by electron metallography and selected-area diffraction of foils examined in transmission in the electron microscope. EXPERIMENTAL METHODS The alloys have been prepared from thoroughly mixed powders of pure iron (99.6+ pct, 0.06 max pct C, 0.15 max pct N), chromium (99.9+ pct), and nickel (99.9+ pct). After sintering in an Ar-H2 atmosphere, the mixtures were melted by induction heating in recrystallized alumina boats under purified argon. The ingots were cold-rolled to 0.4-mm sheets (100 pct reduction in thickness) after the removal of at least 1.5 mm from their surfaces by grinding. Three-millimeter discs were punched from the cold-rolled sheet and annealed at 1150°C for approximately 24 hr in evacuated quartz capsules. The average grain size was 40 µ Thin foils for examination in transmission in the electron microscope were prepared from discs quenched to liquid-nitrogen temperature. A depression was first jet-machined into the center of a disc and a thin area (less than approximately 3000A in thickness) was produced at the base of the depression by electropolishing. Electron-microscope studies utilized the RCA EMU-3 and the Philips EM-100B microscopes operating at 100 kv. X-ray examination of the polycrystalline alloys was performed either in a diffractometer or in a

Jan 1, 1964

By E. Teghtsoonian, E. M. Schulson

The tensile behavior of bcc ordered P' AuZn single crystals (CsCl structure) has been investigated under varying conditions of temperature, composition, and orientation. Between -0.2 and 0.4 T, multi-stage hardening occurs fm stoichiometric and nonstoichio-metric crystals oriented near the middle of the primary stereographic triangle. At higher and lower temperatures, parabolic type hardening occurs, followed by work - softening at the higher temperatwes. Deviations from stoichiometry give rise to increased flow stresses. Multi-stage hardening was observed for most orientations, except along the [loll-[lll] boundary and near the [001] corner of the stereo -graphic triangle, where parabolic type hardening occurs. Along two slip systems, (hk0)[001] and (, operate simultaneously while in the [001] comer, slip occurs mainly on the system. Electron microscopy of deformed crystals revealed bundles of edge dislocations forming walls approximately Perpendicular to the glide plane. In general the plasticity of 4' AuZn closely resembles the plasticity of bcc crystals. In recent years, considerable interest has arisen concerning the mechanical properties of the CsCl type intermetallic compounds Ag Mg,'- Fe co,' and Ni Al.'-' The compound P'AuZn is structurally similar. It has a low and congruent melting point of 725"~,'" remains ordered up to the melting point,16 and pos-esses a range of solid solubility from 47.5 to 52.0 at. pct Au at room temperature.15 The present paper reports the results of an investigation on the general tensile behavior of material in single crystal form. Some dislocation configurations characteristic of the deformed state are also reported. The results of a detailed study of the slip geometry in AuZn are presented in a separate paper.17 PROCEDURE Alloy preparation, crystal growing techniques, and the procedure followed in selecting specimens of minimum composition variation are reported elsewhere.17 Dumb-bell shaped tensile specimens were prepared by carefully machining single crystals in a jewellers' lathe to a gage length of 0.80 in. and diam of 0.090 in. Back-reflection Laue X-ray patterns and room temperature tensile tests revealed that machining damage could be eliminated by electrochemically polishing 0.005 in. from the machined surface followed by annealing at 300°C for 1 hr. Specimens were polished in fresh 5 pct KCN solution (40°C, 12 v). Experiments were performed by gripping specimens in a self-aligning pin-chuck and threaded collet system, then straining in a floor model Instron tensile machine. All tests were performed in duplicate. Experimental variables included temperature, composition, and orientation. Unless otherwise stated the strain rate was 2.5 x 10"3 per sec. Liquid testing environments included nitrogen (WOK), nitrogen cooled petroleum ether (133" to 293"K), and silicone oil (293" to 488°K). Resolved shear stress-shear strain curves were electronically computed from autographically recorded load-elongation curves. Stress and strain were resolved on the macroscopic noncrystallographic (hkO) [001] system operative under the specific test conditions of temperature, strain rate, and orientation reported earlier.17 RESULTS The temperature dependence of the work-hardening curves is shown in Fig. 1 for gold-rich crystals of 51.0 at. pct Au oriented near the center of the stereo-graphic triangle. Over the range of intermediate temperatures from -200" to 400°K, they are very similar to those classically observed for fcc metals (reviewed by Nabarro et al.).'' The beginning of deformation is characterized by a region of decreasing hardening rate, stage 0, which is followed by a region of low linear hardening, stage I, and then a region of higher linear hardening, stage 11. At the higher temperatures, stage 111 is observed, a region of decreasing hardening rate. Over the intermediate temperature range, the extent of stage 0 and of the slow transition between stages I and I1 decreases with increasing temperature. Total ductility is large, often greater than 300 pct shear. As the temperature is either increased or decreased, the extent of stage I is decreased, giving rise to parabolic type flow and reduced ductility. Similar temperature effects have been reported for bcc ~r~stals.~~-~~ Below -14O°K, hardening is terminated in brittle fracture while above -400°K. initial hardening is followed first by work-softening and then by chisel-edge type ductile fracture. Stoichiometric (50.0 at. pct Au) and Zn-rich (51.0 at. pct Zn) crystals were also tested from 77" to -500°K. The effect of composition on the flow behavior is illus-

Jan 1, 1970

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

By B. D. Cullity, K. S. Sree Harsha

When a copper or aluminum single crystal is swaged into wire, the resulting deformation texture depends on the original orientation of the crystal. The<100> and <111>orientations me essentially stable, while <110> is unstable. The greater the <100> content of the deformation texture, the stronger the wire is in torsion. the greater the<111>content, the stvonger it is in tenszotz. The preferred orientation (texture) of fcc wires, either after deformation or recrystallization, is usually a double fiber texture in which some grains have <100> parallel to the wire axis and others have <111>. The relative amounts of these two texture components, as reported by different investigators for the same metal, vary considerably. Previous work in this laboratory&apos; has shown that the starting texture of a wire, i.e., the texture which it has before deformation, can have a decided influence on the texture produced by deformation. In particular, it was found that the deformation texture of copper wire is essentially a single <100> texture, if the wire before deformation contains only a <100> component. This is true even when the deformation is carried to more than 98 pct reduction in area. This paper reports on further studies of the role played by the starting texture. Copper and aluminum single crystals of various orientations have been cold swaged into wire, and quantitative measurements of the resulting deformation textures have been made. The tensile and torsional properties of the deformed wires have also been measured, and the relation between these properties has been correlated with the texture of the wire. These measurements were made in order to demonstrate that a cold-worked wire can be made relatively strong in torsion and weak in tension, or vice versa, by proper selection of the texture before deformation. MATERIALS The copper was of the tough-pitch variety, containing, by weight, 99.962 pct Cu, 0.003 pct Fe, 0.025 pct 0, and 0.0021 pct Si. The aluminum contained more than 99.99 pct .&apos;41; the only reported impurities were 0.001 pct Fe, 0.001 pct Si, and 0.003 pct Zn, by weight. Large single crystals of these metals were grown by the Bridgman method in graphite crucibles and a helium atmospliere. Cylindrical specimens of predetermined orientation, about 1.5 in. long and 0.36 in. in diameter, were machined from the as-grown crystals and then etched to 0.25 in. to remove the effects of machining. Their orientations were checked by back-reflection Laue photographs, and they were then swaged to a diameter of 0.050 in. (96 pct reduction in area). 111 order to study the "inside texture" of the deformed wires, they were etched, after swaging, to a diameter of 0.040 in. before the texture measurements were made. TEXTURE MEASUREMENTS The fiber texture which exists in wire or rod can be represented by a curve showing the relation between the pole density I, for some selected crystal-lographic plane, and the angle $ between the pole of that plane and the wire axis (fiber axis). Such a curve will show maxima at particular values of , and these values disclose the texture components which are present. The relative amounts of these components can be determined2&apos;3 from the areas under the maxima on a curve of I sin F vs F. It is seldom necesszlry to measure I over the whole range of F from 0 to 90 deg, since the existence of maxima in the low-F relgion can be inferred from measurements confined to the high-F region. The X-ray measurements were made with a General Electric XRD-5 diffractometer and filtered copper radiation, according to one or the other of the following procedures: 1) A method developed in this laboratory,4 involving diffraction from a single piece of wire. 2) A modification of the Field and Merchant method.5 This method was originally devised for the examination of sheet specimens, but it can easily be adapted to the measurement of fiber texture. Three or four short lengths of wire are held in grooves machined in the flat face of a special lucite specimen holder. The axes of the wires are parallel to the plane defined by the incident and diffracted X-ray beams, and the holder to which the wires are attached can be rotated step-wise about the diffractometer axis for measurements at various angles 9.

Jan 1, 1962

By Charles C. Templeton

Any explanation of the nature of multiphase fluid flow through porous media must ultimately involve a knowledge of the mechanism of such flow through the individual pores of the medium. To provide quantitative information of the latter type, a study was made of gas-liquid and liquid-liquid displacements in single uniform Pyrex capillaries with diameters as small as 4 microns. Quantitative observation of air-liquid displacements with zero contact. angle indicates the adequacy of a model based on Poiseuille&apos;s Law and the independence of capillary pressure and interfacial velocity. Consequently, this work discounts previous claims that flow is abnormally retarded in very small capillaries. For the displacement of a very viscous oil by water in a capillary initially filled with water, flow is faster than predicted by the above model. This behavior is probably due to the existence of a thin annular film of water between the oil column and the capi1lary wall as postulated by Yuster. INTRODUCTION The need for experimental observation of the microscopic nature of multiphase fluid flow, to further the understanding of the results of macroscopic flow investigations, has been previously recognized. Chatenever and Calhoun1 in connection with the API Project 47B have extensively studied the flow of fluids through layers of glass or lucite spheres between glass or lucite plates. Lowman2 prepared an interesting film concerning flow in a single capillary, using an apparatus which made a moving interface appear stationary in the field of a microscope. The purpose of the present investigation was to deter- mine what contribution might be made to this field by comprehensive quantitative observation of gas-liquid and liquid-liquid displacements in single capillaries of uniform, very small diameter. The techniques used are similar to those of Lowman but incorporate improvements necessary for quantitative work. Quantitative observations must begin with fluids of simple chemical composition to provide a basis for analyzing the more complex behavior that may be expected with natural reservoir fluids. However, some qualitative observations on systems involving crude oils are presented. Experiments of this sort involve the observation of the velocity of the interface separating two fluids, and have been performed in horizontal or vertical capillaries by several investigators.3,4,5,6,7,8 The most general treatment of their mechanics, by Brittin,9 involves forces due to capillarity, viscous resistance, gravity, an "end-drag" effect, and the rate of change of momentum of the capillary contents. Since the range of pore diameters of interest in petroleum reservoirs is about 0.1 to 100 microns, it was desired to perform these experiments in the smallest capillaries possible, to ascertain whether capillary diameter had any effect on the existing theory based on data from larger capillaries.* It was also important to be able more systematically to vary the direction and rate of displacement than was done by previous investigators. Finally, to concentrate attention on viscous and capillary forces by eliminating gravity as a parameter, this study involves only horizontal capillaries. The work of Eley and Pepper&apos; with a "large" (0.766-mm diameter) horizontal capillary is the previous investigation which is most similar to the present method of quantitative observation. Here capillaries with diameters as small as 4 microns will be studied.

Jan 1, 1955

By Donald L. Katz, Leslie J. Noaker

Experimental data are presented for hydrate formation conditions for mixtures of hydrogen sulfide and methane. Vapor-solid equilibrium constants for hydrogen sulfide are also presented. Equilibrium constants, defined here as the ratio of the mole fraction of hydrogen sulfide in the vapor phase (dry basis) to the mole fraction of hydrogen sulfide in the solid phase (dry basis), were calculated using the vapor-solid equilibrium constants for methane presented in an earlier paper. The conditions at which a natural gas will form gas hydrates with water may be computed from its composition, when hydrogen sulfide is present in addition to carbon dioxide and the paraffin hydrocarbons. INTRODUCTION Many gases are known to form solid hydrates in the presence of liquid water at temperatures above 32°F. This hydrate formation is of importance to the natural gas industry inasmuch as most of the constituents found in natural gases will form hydrates. The attention of the industry was called to hydrates by Hammer-schmidtl0 in 1934. A number of papers have been written giving the temperatures and pressures at which these hydrates will form3,4,5,6,7,8,9,10,13,14,15,18,19 and a bibliography on the subject has been compiled13. Deaton and Frost4,5,6,7,8 report work for various pure gases and for some natural gases. Katz and co-workers3,4,13,14,18,19 have reported data for various gases at high pressure. They developed a method of predicting conditions for hydrate formation from equilibrium constants3,19 and from gab gravity." The effects of anti-freeze agents on the formation of hydrogen sulfide hydrate were reported by Bond and Nelson.&apos; The hydrogen sulfide-water system, including hydrate, has been the subject of recent investigation by Sage and co-workers." Mixtures of hydrates behave as solid solutions and an equilibrium exists between the vapor phase and the solid phase that appears to be comparable to the equilibrium between vapor and liquid phases.3,10 By means of the vapor-solid equilibrium constants which have been published for methane, ethane, propane, iso-butane, and carbon dioxidel6 it is possible to determine the temperature and pressure at which hydrates will form for a specific gas mixture when water is present. Hydrogen sulfide which is frequently found in natural gases has a very strong tendency to form hydrate and must enter the solid solution when present in a natural gas forming a hydrate. To determine the effect of hydrogen sulfide when computing the conditions for gas hydrate formation, it is necessary to have the equilibrium constant giving the ratio of the concentration of hydrogen sulfide in the gas phase to the concentration in the solid phase. This paper presents data on hydrate formation for mixtures of hydrogen sulfide and methane and presents the equilibrium constants which were calculated from these data. EXPERIMENTAL PROCEDURE The apparatus used to determine the conditions of hydrate formation for the methane-hydrogen sulfide system was similar to that employed by previous investigators.3,18,19 A charge gas cylinder was used to supply the hydrogen sulfide-methane mixtures, called the charge gas, and to supply the pressure up to 1.000 psia. This

Jan 1, 1955

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman&apos;s2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman&apos;s method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman&apos;s2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

By Noel Jarrett, Allen S. Russell, Bernard M. Starner, Stanley C. Jacobs

A process has been developed to refine high-grade commercial aluminum to 99.99 pct purity. This enzploys precipitating titanium, vanadium, and zirconiu~ as borides. The upgraded liquid is partially crystallized under conditions that prevent massive freezing. The resulting crystals are compacted and washed free of adhernig impure liquid aluminum by melting the top crystals while draining off the liquid. Finally, the bottorn portion of the crystal bed is melted and removed as the pure product. Leakage from the crystallizat~on vessel is prevented by a layer of alumina granules that are not wetted by the aluminum. ALUMINUM of 99.99 pct purity is desired in a variety of applications. These include electrolytic capacitors, catalyst carriers, decorative trim for automobiles, aluminum powder, and high-strength alloys. This market was for many years filled by refining commercial-purity aluminum in a three-liquid-layer electrolytic cell of the type originally proposed by Hoopes. To meet the expanding need for lower-cost high-purity aluminum, a refining process based on chemical precipitation and fractional crystallization was developed. The availability of this super-purity metal was announced in November 1961, and three patents1-3 relating to the process were issued in 1965. An alternate process, comprising continuous fractional crystallization of a portion of a liquid-aluminum feed stream under conditions of strong agitation at the surface of the growing crystals, was published by Dewey4 in 1965. Earlier proposals by Larsen 5 and by Regner6 also emphasized the advantage of rapid agitation of the melt in the region of the crystallization zone. johnson 7 more recently proposed extracting purified aluminum from an alloy by mixing crystals of pure aluminum into the molten alloy, allowing them to grow, and removing the pure aluminum as by casting. Aamot&apos;s 8 recent patent describes a freeze refining process that involves controlled partial freezing against cooled moving retort walls. The Alcoa process to produce high-purity aluminum is schematically described in Fig. 1. Relatively pure aluminum is treated with boron in a furnace (a) to precipitate high melting point impurities, the supernatant liquid is transferred to a crystallization vessel (b), the liquid is partially crystallized with mechanized "tamping" (c), the remaining impure liquid is tapped out and the crystal bed partially and directionally re-melted to wash the underlying crystals (d), and the balance of the crystals is melted and withdrawn as high-purity aluminum (e). PRINCIPLES OF FRACTIONAL CRYSTALLIZATION Commonly encountered impurity elements form two types of systems with aluminum. Titanium, vanadium, and some other transition elements in periodic groups IV, V, and VI are the high melting point impurities. Initial solidification of aluminum containing small percentages of these elements will produce solid markedly enriched in them at temperatures slightly above the freezing point of high-purity aluminum. Most other elements, such as silicon and iron, produce eutectic type reactions with aluminum. In this case the first solid formed on initial solidification at temperatures slightly below the freezing point for high-purity aluminum is markedly depleted while the remaining liquid is enriched in these elements. The equilibrium change in composition during solidification of aluminum contaminated with silicon, iron, or titanium is illustrated in Fig. 2. Here, for clarity, the temperature scale is expanded beyond the

Jan 1, 1968

By S. Chander, D. W. Fuerstenau

The inherently sluggish nature of the reactions involving sulfide minerals, particularly molybdenite, in aqueous solutions under ambient flotation conditions make their investigation complicated and difficult. Since the physicochemical nature of sulfides is known to be controlled by electrochemical reactions, a number of attempts have been made in the past to study sulfide mineral-collector interactions through rest potential and electrode polarization measurements. The purpose of the present investigation was to study the interaction of potassium diethyldithiophosphate (KDTP) with molybdenite. In the present investigation of the interaction of KDTP at the molydenite surface, molybdenite electrode rest potential measurements and electrode polarization behavior were experimentally determined under various solution conditions. The standard reduction potential for the equilibrium between dithiophosphate ions (DTP-) and bis(diethoxythiophosphoryl)disulfide (DTP) [(DTP). + 2e :i7-± 2DTP- (1)] can be evaluated from the electrode rest potential measurements on a platinum electrode in deoxygenated KDTP solutions saturated with freshly prepared (DTP)2. Experimental A platinum wire was used as the electrode for potential measurements. Prior to each measurement the elec-

Jan 1, 1975

By Donald E. Garrett

The processing of brines from Searles Lake, California, yields one of the world&apos;s largest supplies of borax and boron chemicals, second probably only to the massive deposit at Boron, California. Two companies produce from this deposit, the American Potash & Chemical Corp. and the West End Chemical Co., a division of the Stauffer Chemical Co. Two processes are employed in recovering borax from the brines; one is used by both companies and consists of carbonating the brine to form sodium bicarbonate, removing this, and then cooling the liquor to crystallize a crop of borax. Only American Potash uses the second process, evaporating the brine to concentrate it and remove (crystallize) much of its NaCl, Na2CO3, Na2SO4, and NaLi2PO4 content, quick cooling the remaining liquor to remove KCI, and then seeding the filtrate to remove borax. Both methods will be briefly described. Searles Lake is a large evaporite body formed during the most recent two Sierra Nevada ice stages, the Tahoe and the Tioga. Runoff waters from the Sierra Nevada Mountains collected in the large Owens Valley drainage basin and from there overflowed into the Indian Wells basin and then into Searles Lake. In each Lake, evaporation took place. To a large extent the Owens and Indian Wells lakes acted as settling basins, for much of the mud, and insoluble calcium and magnesium precipitates were deposited there. Recent volcanic activity in the mountains to the north and east of Owens Lake had scattered considerable mineral-rich volcanic ash and debris throughout the drainage area, and several hot springs were formed that contained boron and other salts. The present flow rate and concentration of several springs, and the known age of at least the Tioga zone, can fairly well account for all of the boron present in Owens and Searles Lakes.1 The tungsten content can be accounted for in a similar manner.2 Most of the salts thus originally present in the fresh water runoff-from ice, snow, and rain-accompanying these two ice stages were ultimately deposited in Searles Lake. During the Tahoe period, from 25 to 40 ft of massive, mixed salts were deposited, along with six interspersed layers of mud (four inches to two feet thick) representing comparatively brief interglacial periods. Before the final desiccation of the lake, from 10 to 14 ft of new mud was deposited, representing the Tioga stage. The crystals subsequently deposited were from 70 to 90 ft thick, and form the present lake surface. The extent of the salt body is about 34 square miles, of which 12 square miles are exposed salt; the remaining area is covered by recent alluvial deposits (chiefly mud). The present lake is generally dry on the surface but floods to a shallow depth following heavy rains. The crystal body of both zones consists of continuous clusters of salts, and the voids between crystals (about 45 pct of the total volume) are occupied by brine. The level of this brine never recedes more than several inches below the salt surface. The brine pumped to the plants for processing is generally saturated with all of the solid phases present in that area, and thus is a complex mixture containing about 35 pct solids (see Table 3). The brine composition varies somewhat at different areas of the lake and from upper to lower structures, so wells are drilled in the areas and to the depths desired. A casing is cemented in the hole to within a short distance from the bottom, and pumps with about 14-ft suctions are mounted on the casing to pump the brine into the plants. The evaporation process of the American Potash & Chemical Corp. treats upper structure brine, evaporating all of the water from

Jan 1, 1960

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940