Search Documents

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

By Noris Del Be1 Belluz

Drilling underground in the Grasberg dewatering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are used. Pilot holes probe ahead of the tunnel development to intersect aquifers ahead of the face. And dewatering holes dewater rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, static pressures of >8.3 MPa (> 1,200 psi) have been recorded with flows from a 100 mm (4 in.) HQ core hole measured at 5,700 L/min (1,500 gpm). The waterflows can be slightly acidic, necessitating the use of stainless-steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early on to deal with these conditions. PT Freeport Indonesia (PTFI) established procedures to maintain the safety of the drill crews, to enable coring of the rock, and to maintain the safety of the miners driving the drifts. The collar gear controls the waterflows because these drill holes are a vital source of water for the concentrator.

Jan 1, 1998

By M. R. Yalamanchili, W. H. Jang, Y. Ye, J. D. Miller

Typically, rougher molybdenite flotation and recovery from bulk copper/molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment to depress copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40% and 90% at a concentrate grade of 5% to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Mo concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning resuIts in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/fotation strategy, the process is technically and economically viable and should be suitable for industrial ap¬plication.

Jan 1, 1991

By F. Warnaars

Historically, this area produced gold and silver from many well-known vein deposits, like Tayoltita, Topia, and San Jose de Gracia. Modern exploration identified three categories of deposits: 1) low grade porphyry golds in shallow level dacite porphyries; 2) batholith-related deposits; and 3) those formed in volcanic sequences of Late Cretaceous to Late Tertiary. At least four porphyry golds have been identified, of which Metates is best known. These are formed by and within dacite porphyries, associated hydrothermal breccias and sometimes within surrounding metasediments. Their ages are from mid-Cretaceous to Early Tertiary. Precious metal deposits associated with batholiths occur as veins, contact haloes in metasediments or volcanics, skarns, tectonic breccias, hydrothermal tourmaline breccias, dacite dikes or as disseminated or stockwork deposits such as La Fortuna. Several new gold discoveries were made in older Early Tertiary Volcanic Sequences and in the younger Tertiary volcanics within prominent structures exceeding 3 to 5 km in lengths. Some of these are open-pittable but most have to be mined by underground methods.

Jan 1, 1999

By M. G. Premo

The McKinley Mine is located in the northwest New Mexico, in McKinley County, approximately 25 miles from Gallup. The mine is operated by The Pittsburg & Midway Coal Mining Co. (P&M), a wholly owned subsidiary of the Chevron Corporation. P&M is headquartered in Englewood, Colorado. Since the McKinley Mine began operations in 1962 a total of 83,391,000 metric tons of coal have been sold through 1990. The 1991 production was approximately 5.000.000 metric tons. The mine operations are contained on a 109.000 square kilometers lease area of which 44.000 square kilometers are on the Navajo Nation. The present customer base consists of four utilities and one industrial account, all of which are located in Arizona. The utility customers are the Arizona Public Service Co. Cholla Station at Joseph City, The Salt River Project. Coronado Generating Station near Joseph City, and The Tucson Electric Company, Irvington Generating Station in Tucson. The industrial customer is the Stone Container Corporation, Snowflake Paper Mill.

Jan 1, 1992

By F. F. Peng, D. C. Yang, G. Yanief, E. H. Cho

This study deals with carrier flotation of cerium dioxide, a surrogate of plutonium oxide, which is the major contaminant at the Nevada Test Site (NTS). The objective of this study was to determine the feasibility of using carrier flotation for remediation of the site. In this study, a - 200-mesh fraction of pure cerium dioxide was used. Oleic acid was used as the collector, while calcium carbonate was used as the carrier. Mechanical-cell tests were conducted to float the surrogate from a mixture containing uncontaminated NTS soil, both in the absence and presence of the carrier. It was found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34% to 65% by adding only 0.5% calcium carbonate (-150 mesh). The recovery further increased to 95% by adding 10% calcium carbonate. The flotation method utilizing a carrier of calcium carbonate seems to have a high potential for the remediation of the soil contaminated with radionuclides at the NTS.

Jan 1, 1998

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By M. G. Karfakis

This paper examines the chimney occurrences in the Hanna Coal Field, Wyoming. Chimney caving is defined, previously proposed mechanisms involved in the development of a chimney are critically reviewed, and factors controlling chimney cave are identified. The main portion of this paper deals with the identification and characterization of chimney subsidence due to underground coal mining in the Hanna Mining District. In an attempt to characterize the subsidence, sink-hole occurrences are correlated with the depth of coal, thickness of mined-out beds, mining methods, nature of overburden, structural geology, and hydrology. Most sinkholes in the Hanna Basin appear to be conical in profile, with the apex upward. The average diameter is 15 meters (50 feet), with an average depth of 11 feet. Most have developed above an overburden of less than 61 meters (200 feet). The average mining height to width ratio is 5. Much of the chimney development is governed by the thickness and character of the overburden, the width and height of the mine opening, and the in situ state of stress.

Jan 1, 1986

By M. S. Janssen

The development of a design equation for, and the testing of, a constant- flow airlift pump IS described. The predictions of the new airlift model agree with the results of experiments carried out using riser diameters between 0.025 and 0.300 m, submergence depths between 5 and 10 m, suspension densities between 1000 and 1650 kg/m3, and a solids dg of 70 to 100µm. The predictions o the model also agree with data from the literature for submergence depths that reached 130 m. This airlift model was employed to simulate the pulp flow through a series of tanks, each of which was fitted with an airlift pump to transfer the suspension to the next tank. Particular attention was paid to the riser diameter, submergence of the airlift pump, and control of the air supply to the airlift pump during the simulated operation of a series of tanks. The results of the simulation highlight some design parameters that could affect the efficiency and operation of a plant that employs airlift pumps to transfer suspensions.

Jan 1, 1989

By M. Takayasu, J. Y. Hwang, F. J. Friedlaender, G. Kullerud

Al unite has been used as raw material for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores are quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 µm. Adequate separation techniques for such ultrafine particles have not been developed. A new method for the beneficiation of al unite ore is proposed in this study. This method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g., an al unite concentrate of 90% grade with 80% recovery, has been obtained from Utah ore. Techniques for selective co-flocculation of magnetite and quartz, separation of the carried quartz, and recovery of magnetite after separation are discussed.

Jan 1, 1987

By Richard L. Bullock

At the beginning of the previous chapter, variation in the types of room-and-pillar stopes were briefly identified so that the reader could begin to understand the extensive application of this mining system. These same variations will be reviewed and elaborated upon in this chapter while discussing the methods by which the material is extracted. FULL-FACE SLICING BY DRILLING AND BLASTING When the entire mineralized thickness is taken in one pass of mining, it is known as full-face slicing. There is no mineral of economic value intentionally left either in the floor or the back. Theoretically, there is no limit as to how high the face could be in a single pass. But there are practical limitations to equipment size, pillar stability, and control of local loose slabs on the face, roof, and pillars that dictate current practices. The range of face height of the 15 typical room- and-pillar mines covered in Table 8 (Sec. 1, Subsec. 7) from the Dravo report, 1974 was 1.7 m (5.5 ft) to 9.8 m (32.1 ft), the average being 5.2 m (17.1 ft). In the Gaspe copper mine, Murduchville, Que., the drill jumbos were constructed with an extendable tower for full-face mining up to 15.2 m (49.9 ft) if necessary. However, a more common practice at that mine is to take the ore in multiple slices (Hall, 1959). In many metal mines the normal practice when starting stoping is to drive a single development drift into the ore zone a distance that will allow at least four or five rooms to be opened on each side of the initial drift. Since this opening will probably serve as the main haulage drift, it should be kept as straight and as level as possible. As to the other criteria for the stope developments, it might be well at this point for the mine planner to review the remarks presented earlier (Sec. 1, Subsec. 7) on drifts, entries, and crosscuts for production. After the initial drift is driven, it should be slabbed to the full room width if it is not that wide already. Next, the future pillars should be marked on the ribs and the rooms driven between them. If the ore extends beyond the length of the initial drift and is to be mined in the normal sequence of mining, care should be taken in a random room-and-pillar system to see that the extension of the initial roadway remains straight. If pillar "spotting" is left to the shift foreman or to the miners, they probably will not realize the importance of maintaining a uniform pillar line next to the roadway, and of keeping the line straight. Invariably, a pillar will end up in the middle of the future drift extension resulting in a "dogleg" in a possible main haul- age road. While this error is not catastrophic, too much weaving in and out of pillars will certainly slow down future production haulage and needlessly increase costs. Face or Breast Drilling and Blasting Practices To drill and blast the initial advances into the rock, usually some form of cut pattern must be used. In room-and-pillar mining, when a pattern is drilled in a face and that face is the only exposed surface to which all of the rock must be broken, the pattern is known as a "face round" or "swing." The face to which the rock must be broken is referred to as a "free face." Thus the most common way to advance a room into virgin rock with only one free face is by drilling swings. If, after breaking around a pillar, taking down back, or taking up bottom, there is a second (or third) face exposed, a group of holes drilled nearly parallel to a free face and breaking to it is known as a "slab round" or "slabbing." In some mining districts it is also known as "slashing." Obviously, because two faces exposed offer less resistance to fragmentation than a single face, slabbing requires less drilling and fewer explosives than required to break the same tonnage with the same degree of fragmentation with swings. Therefore, it behooves the driller (or supervisor) to plan the combination of

Jan 1, 1982

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By James T. Curry

The steady growth of the Northwest portion of the United States over the past two decades, and the very rapid development of Northern California, Western Nevada, and Oregon in particular, led the Calaveras Cement Company people to Shasta County, California in 1957. The presence of a large deposit of high calcium carbonate limestone had been recognized for many years, but it required the momentum of an expanding economy to make these long known reserves valuable. This, plus the availability of a reliable supply of fuel in the form of natural gas, and the ready means of shipping the product to the consumer both by highway and railroad, seemed to offer the proper combination to launch a successful venture. The Calaveras Cement Company had been manufacturing cement by the wet process since 1925 at their plant at San Andreas, California. Starting with two small kilns, the plant in Calaveras County started an expansion program in 1945 that ultimately resulted in the plant as it exists today, consisting of five kilns with a combined production of 4.5 million barrels annually.

Jan 1, 1967

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, gold-silver deposit. Current proven and probable reserves are 8.9 Mt (9.8 million st) grading 1.5 g/t (0.044 oz/ st) gold, minable by open pit and amenable to heap leaching. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold at Santa Rosa occurs principally as electrum, finely disseminated through intermediate tuffs, and associated with pyrite. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1995

By Rogério C. Guimarães, Antonio E. C. Peres

Arafertil's oxidized ore presents barite grades that oscillate between 5 and 12%. The barite separation plays a major role in the production of apatite concentrates for the manufacturing of phosphate fertilizers. The selectivity, via flotation, in the system barite-apatite is inherently difficult due to the similarity of the physical/chemical characteristics of these minerals. The evaluation of the relevant aspects of this separation was performed based on the determinations of the electrical surface charge of barite and apatite, the abstraction isotherms of cetyl-stearyl sodium sulfate and fatty acids soaps for barite and apatite, microflotation in a modified Hallimond tube, and flotation tests in a batch column. The results showed that the adsorption of cetyl- stearyl sodium sulfate occurs preferentially onto barite, in comparison with apatite. On the other hand, the rice bran oil soap presents similar adsorption levels onto both barite and apatite. The cetyl-stearyl sodium sulfate was selective as a barite collector in the presence of apatite, a fact that was not observed in the case of rice bran oil soap.

Jan 1, 1999

By Kenneth R. Maser

In the past 30 years, great advances have taken place in the development of tunnel boring machines, raise drills, large diameter drills and blind shaft borers that have revolutionized the shaft sinking and tunneling industries. Techniques for placing concrete linings, however, have not changed significantly during this period, and still constitute a stumbling block to the achievement of the rapid construction. In the past 5 years, Foster-Miller Associates, Inc. (FMA) has been involved with the development of a remotely operated shotcrete system for lining raise drilled shafts, an Extruded Tunnel Lining System (ETLS) for lining TBM bored tunnels, and a Continuous Shaft Lining System (CSL) for lining any type of machine bored shaft. This paper presents an overview of these three developments, including capabilities and limitations, a description of the concrete production, concrete placement, and advance rate, and control subsystems, a description of the concrete mix development required for each system, a discussion of test results to date, and an assessment of the state of development of each concept. Plans for future development will also be presented.

Jan 1, 1981

By S. K. Kawatra, S. J. Ripke

During iron ore pellet production, bentonite clay is used as a binder. Typical pellet plants spend from $3 million to $5 million annually for the clay. If bentonite dosages could be reduced by using it more efficiently, a significant cost savings would result. If the binding mechanisms can be completely understood, procedures can be developed to use bentonite more efficiently. Classical bentonite bonding theory is based on the behavior of bentonite at low percent solids and high mixing shear rates. Under these conditions, bentonite was understood to expand, disperse into platelets, and dry into a bonding "film" or "gel." However, these are not the conditions that exist during pelletization, which is carried out at high percent solids and relatively low shear rates. In this paper SEM imaging was used to identify and explain the bonding mechanisms of bentonite on the surface of magnetite concentrate. It was determined that bentonite would form a fibrous network under the proper conditions and that the formation of these fibers corresponded with an increase in the bonding of particles by the bentonite.

Jan 1, 2000

By John M. Hird

Texasgu1f's Lee Creek Mine in Eastern North Carolina is usin8 a combination Dredge-Dragline method for mining deep phosphate ore at a rate of 8.5 million tons per year. The matrix is thick, uniform in grade, and is processed into agricultural products. As in many other good mineral deposits, there are tough obstacles to overcome in recovering the ore. The deposit is in an area with a land surface of about ten feet above sea level, is close to tidewater, is overlain with 90 to 130 feet of unconsolidated overburden, and is underlain by an artesian aquifer with over 140 feet of natural hydrostatic head at the bottom of the bed, The upper 40 feet of overburden will not support stripping equipment and is unstable when cast as spoil. Barriers are emplaced to prevent flooding from hurricane tides. The ground water problems have been successfully controlled by pumping 60 million gallons per day from the aquifer. Only recently have the severe ground problems been overcome by this unusual Dredge-Dragline combination of mining equipment.

Jan 1, 1978

By O. Alvarez-Campos

Two porphyry copper orebodies, the North and Central MM orebodies, have been found through regional and structural geologic works, about 5 Km south of Chuquicamata, under a gravel bed of approximately 100 m and in the west side of the West Fissure. The mineralization is emplaced in a coarse granodioritic porphyry, predominantly with sericitic alteration. In the North MM ore-body, with 200 million metric tons of 1.0% Cu, the mineralization is mainly chalcopyrite, bornite, digenite and molibdenite. In the central MM orebody, with 700 million metric tons of 1.3% Cu, there are large veins of enargite, chalcocite and bornite, the last one increasing in depth, separated by chalcopyrite and pyrite zones; in these veins there are interesting gold and silver values. Both orebodies have an upper enrichment of chalcocite and covellite, with pyrite envelope. According with these characteristics, the MM orebodies could he the upper part, with sericitic alteration, of the Chuquicamata porphyry copper system, displaced by the West Fissure system movements, but we couldn't eliminate the possibility that MM can be a new orebody, different of Chuquicamata.

Jan 1, 1993